User`s manual

ManualsBrandsAxis ManualsComputer equipment5670e

AXIS 5570e/AXIS 5670e User’s Manual

AXIS 5570e

AXIS 5670e

User’s Manual

Summary of content (377 pages)

PAGE 1
AXIS 5570e/AXIS 5670e User’s Manual AXIS 5570e AXIS 5670e User’s Manual 1
PAGE 2
AXIS 5570e/AXIS 5670e User’s Manual Safety notices Take some time to read through the safety notices before installing the AXIS 5570e/AXIS 5670e. Please observe all safety markings and instructions when using this product. Warning! - must be observed to avoid bodily injuries. Caution! - must be observed to avoid loss of data or damage to your equipment. Important: - must be observed to avoid operational impairment.
PAGE 3
AXIS 5570e/AXIS 5670e User’s Manual dealer. If your questions cannot be answered immediately, your Axis dealer will forward your queries through the appropriate channels to ensure you a rapid response. On www.axis.com, you will find on-line manuals, technical support, software updates, application software and corporate information. AXIS 5570e/AXIS 5670e User’s Manual Part no.20897 Copyright © Axis Communications AB,2003 Revision 1.
PAGE 4
AXIS 5570e/AXIS 5670e User’s Manual Preface Thank you for purchasing the AXIS 5570e/AXIS 5670e Print Server. These products have been developed to connect your printers anywhere in your network, allowing all network users access to the shared printer resources. About this manual This manual provides introductory information as well as detailed instructions on how to set up and manage the AXIS 5570e/AXIS 5670e in various network environments.
PAGE 5
AXIS 5570e/AXIS 5670e User’s Manual Table of Contents Table of Contents Table of Contents 5 Section 1 Introduction 9 Product Model Summary 9 Where to use it 10 How to use it 11 AXIS 5570e/AXIS 5670e Features and Benefits 12 Section 2 Product Overview 14 Hardware Inventory 14 Protocols and Datastreams 15 The AXIS 5570e Network Print Server 16 The AXIS 5670e Network Print Server 16 Section 3 Basic Installation 19 Getting Started 19 Connecting a printer to the Ethernet Network 20 Installation Guide 22 S
PAGE 6
Table of Contents AXIS 5570e/AXIS 5670e User’s Manual Adding Printers in Windows NT 4 Using the Microsoft LPR Monitor 112 AXIS Print Monitor Software 114 Adding Printers over TCP/IP in Windows NT 4 using AXIS Print Monitor 115 Adding NetBIOS/NetBEUI Printers in Windows 2000 using AXIS Print Monitor 116 Adding Printers over NetBIOS/NetBEUI in Windows NT 4 using AXIS Print Monitor 117 Adding Printers in Windows 98 and Me over TCP/IP using AXIS Print Monitor 119 Adding Printers in Windows 98 and Me over N
PAGE 7
AXIS 5570e/AXIS 5670e User’s Manual Table of Contents Section 10 Management and Configuration 180 Using a Web browser 181 Using AXIS ThinWizard for Print Server Management 189 Using FTP for Print Server Management 192 Using Telnet 195 Using SNMP 199 Using Novell Utilities 201 Configuring the Print Server from an IBM host 203 Section 11 Configuration Possibilities 205 Autodetect Printer Type 205 AutoIP 206 E-mail Notification 206 IPP (Internet Printing Protocol) 207 Logical Printers for Customized Print
PAGE 8
Table of Contents AXIS 5570e/AXIS 5670e User’s Manual Section 18 IPDS Overview 268 IPDS Parameter Settings 268 IPDS System Languages 268 IPDS Fonts 276 Printer Resident Fonts 276 Immediate Font Substitutions 277 Unsupported Fonts 277 Typographical Fonts 278 Section 19 DBCS Support 279 Configuring the AS/400 Host, 5494 CU mode 279 Configuring the AXIS 5570e/AXIS 5670e 280 Verifying the Communications Link 281 Amending Device Features 282 Extended IBM Printer Emulation 283 Font Tables 283 Section 20
PAGE 9
AXIS 5570e/AXIS 5670e User’s Manual Section 1 Section 1: Introduction Introduction Product Model Summary The AXIS 5570e/AXIS 5670e is a LAN attached multi-protocol print server that prints IBM and ASCII data streams to any ASCII printer. Supporting IBM Mainframes, AS/400, NetWare, UNIX, LAN Server Manager, Windows and Apple EtherTalk, these products are ideal for IBM Mainframe and AS/400 sites that are migrating from pure IBM networks to LAN environments.
PAGE 10
Section 1: Introduction AXIS 5570e/AXIS 5670e User’s Manual Where to use it Supported Environments The AXIS 5570e/AXIS 5670e is the ideal print server in mixed environments as it can communicate with all the major computer systems and network protocols including: • IBM Mainframe and AS/400 • Windows • NetWare • UNIX • Windows clients connected to LANtastic networks • Macintosh • Internet via any standard Web browser
PAGE 11
AXIS 5570e/AXIS 5670e User’s Manual Section 1: Introduction How to use it Installation and Integration The installation of the AXIS 5570e/AXIS 5670e and its integration into the network is performed using the appropriate client software, provided with your print server or your operating system. Note: The AXIS 5570e/AXIS 5670e is designed for 10 Mbps Ethernet and 100 Mbps Fast Ethernet networks and connects to the network via a twisted pair RJ45 category 5 cable (10baseT and 100baseTX).
PAGE 12
Section 1: Introduction AXIS 5570e/AXIS 5670e User’s Manual AXIS 5570e/AXIS 5670e Features and Benefits Reliability The AXIS 5570e/AXIS 5670e print server provides high performance and reliability combined with low power consumption. The electronic circuits are based on the AXIS ETRAX 100LX chip, which comprises an integrated 32 bit RISC processor and associated network controllers.
PAGE 13
AXIS 5570e/AXIS 5670e User’s Manual Monitoring Section 1: Introduction The internal AXIS 5570e/AXIS 5670e Web pages allow you to continuously monitor printer status. Integrity of your printing is also monitored via interactive communication with the IBM host. The AXIS Print Monitor for Windows 98, Windows Me and Windows NT can be configured to display pop-up messages that show the status of peer-to-peer print jobs. The AXIS 5570e/AXIS 5670e additionally supports SNMP for remote monitoring.
PAGE 14
Section 2: Product Overview Section 2 AXIS 5570e/AXIS 5670e User’s Manual Product Overview Unpack and check all the items using the following check list. Contact your dealer if anything is missing or damaged. All packing materials are recyclable Hardware Inventory Item AXIS 5570e Model/Title TCP/IP IPDS SNA TCP/IP IPDS SNA Country Part number 0188 0193 0189 0194 Europe 19108 UK 19109 Australia 19111 USA/Japan 19110 CD AXIS Product CD rev 1.
PAGE 15
AXIS 5570e/AXIS 5670e User’s Manual Section 2: Product Overview Protocols and Datastreams The AXIS 5570e/AXIS 5670e are available in two versions; IPDS SNA and TCP/IP. The table below displays the functionality of each version. AXIS 5570e IPDS support SCS support 3270DS support TN3270E TN5250E SNA support Digital Copier Support AXIS 5670e IPDS support SCS support 3270DS support TN3270E TN5250E SNA support Digital Copier Support IPDS SNA (part no. 0193) TCP/IP (part no. 0188) . . . . . . . . . . .
PAGE 16
Section 2: Product Overview AXIS 5570e/AXIS 5670e User’s Manual The AXIS 5570e Network Print Server LPT1 Test Button Network Indicator USB1 Ethernet Connector Power Connector Power Indicator The AXIS 5670e Network Print Server Power Indicator COM1 Network Indicator LPT1 LPT2 Test button Ethernet Connector Power Connector
PAGE 17
AXIS 5570e/AXIS 5670e User’s Manual Section 2: Product Overview Backside label on print server Serial number Printer Ports AXIS 5570e is equipped with one USB port that is USB 1.1 and 2.0 low and full speed compliant, and one high-speed IEEE 1284 compatible parallel port AXIS 5670e is equipped with two high-speed IEEE 1284 compatible parallel ports and one RS232 serial port.
PAGE 18
Section 2: Product Overview AXIS 5570e/AXIS 5670e User’s Manual Power Indicator The power indicator is lit while power is applied. If it is not lit, or if it flashes, there is a problem with the print server or its Power Adapter. Configuration and Management The print server can be configured and managed from its internal Web pages, using HTTP as well as HTTPS in the secure mode.
PAGE 19
AXIS 5570e/AXIS 5670e User’s Manual Section 3 Section 3: Basic Installation Basic Installation Getting Started After you have verified that no items in Product Overview, on page 14, are missing from the package, you are ready to install your AXIS 5570e/AXIS 5670e. Follow the instructions below to install the AXIS 5570e/AXIS 5670e in your environment: 1. Start the procedure by connecting the AXIS 5570e/AXIS 5670e to your network and printer.
PAGE 20
Section 3: Basic Installation AXIS 5570e/AXIS 5670e User’s Manual Connecting a printer to the Ethernet Network Follow the instructions below to connect a printer to the network via the AXIS 5570e/AXIS 5670e print server. Important: Make sure that the AXIS 5570e/AXIS 5670e external power supply is marked with the correct voltage! 1. Switch off the printer(s) and disconnect the AXIS 5570e/AXIS 5670e external power supply. 2.
PAGE 21
AXIS 5570e/AXIS 5670e User’s Manual Section 3: Basic Installation Mounting the AXIS 5570e Using the supplied clip and holder, the AXIS 5570e can be mounted e.g. on the back of the printer or on a wall. Adhesive Clip Fasten to print server by peeling off adhesive tape. Adhesive Holder Fasten to mounting surface by peeling off adhesive tape. The print server can now be installed in your network using one of the methods detailed in the Installation Guide, on page 22.
PAGE 22
Section 3: Basic Installation AXIS 5570e/AXIS 5670e User’s Manual Installation Guide After connecting the AXIS 5570e/AXIS 5670e to your network, you are now ready to perform the basic setup procedures. The method of installation that you choose should be dictated by your printing requirements and the type of network into which you are integrating. 1. Start out with setting an IP address on the print server, described in Setting the IP address, on page 24. 2.
PAGE 23
AXIS 5570e/AXIS 5670e User’s Manual Installation Tools Section 3: Basic Installation The recommended installation tools and management methods for the AXIS 5570e/AXIS 5670e are summarized here: Protocols Operating Systems Configuration method Management method TCP/IP Windows 2000/XP Windows Standard Add Printer Wizard Web Browser, FTP, Telnet, SNMP AXIS ThinWizard TCP/IP Windows 98/NT/Me AXIS Print Monitor software and Windows Add Printer Wizard Web Browser, FTP, Telnet, SNMP TCP/IP Mac OS
PAGE 24
Section 3: Basic Installation AXIS 5570e/AXIS 5670e User’s Manual Setting the IP address Dynamic IP Address Assignment Method Server required Comment DHCP DHCP server Dynamic assignment of IP addresses. See Dynamic IP Address Assignment, on page 24 RARP RARP server Static assignment of I P adresses. Cannot be used over routers. See Dynamic IP Address Assignment, on page 24 BOOTP BOOTP server Static assignment of IP addresses.
PAGE 25
AXIS 5570e/AXIS 5670e User’s Manual Section 3: Basic Installation Dynamic IP address Assignment Obtaining an IP address through DHCP • • Obtaining an IP Address through AutoIP Important: If you have a DHCP server on your network, your print server will receive an IP address automatically. The IP address will then appear on the test page printed when you press the test button once.
PAGE 26
Section 3: Basic Installation AXIS 5570e/AXIS 5670e User’s Manual Notes: Manual IP address assignment • Use a Web browser with JavaScript support and Java enabled. • The AXIS 5570e/AXIS 5670e supports WINS (Windows Internet Name Service), which is recommended when setting the IP address using DHCP in Windows environments.
PAGE 27
AXIS 5570e/AXIS 5670e User’s Manual Section 3: Basic Installation Note: If you are using host names, you can map a unique host name to the IP address. Refer to your system manuals for instructions on how this is performed on your system. Setting the IP address using AXIS IP JumpStarter First, install AXIS IP JumpStarter which is available free of charge on www.axis.com 1. Select the required server from the serial number list in the IP JumpStarter dialog window. Server menu 2.
PAGE 28
Section 3: Basic Installation AXIS 5570e/AXIS 5670e User’s Manual 7. To access the print server’s web pages, highlight the AXIS 5570e/AXIS 5670e in the list and select Server Home Page from the Server menu. Note: If your print server does not appear in the serial number list, refer to the AXIS IP JumpStarter online help files.
PAGE 29
AXIS 5570e/AXIS 5670e User’s Manual Section 3: Basic Installation Notes: Using RARP in UNIX • The Ethernet address is equal to the serial number, which is located on the underside label of the AXIS 5470e. • The ARP command varies between different UNIX systems. Some BSD type systems expect the host name and node address in reverse order. Furthermore IBM AIX systems will require the additional argument ether.
PAGE 30
Section 3: Basic Installation Using BOOTP in UNIX AXIS 5570e/AXIS 5670e User’s Manual Follow the instructions below to set the IP address using BOOTP: 1. Append the following entry to your boot table. This is typically performed by editing the file: /etc/bootptab :ht=:vm=:\ :ha=:ip=:\ :sm=:gw= Example: npsname:ht=ether:vm=rfc1048:\ :ha=00408c100086:ip=192.168.3.191:\ :sm=255.255.255.0:gw=192.168.1.
PAGE 31
AXIS 5570e/AXIS 5670e User’s Manual Section 3: Basic Installation Notes: • The AXIS 5570e/AXIS 5670e supports WINS (Windows Internet Name Service), which is recommended when setting the IP address using DHCP in Windows environments. • The Ethernet Address is the same as the serial number, found on the print server’s underside label. Enter the Ethernet Address in the same format as in the example above.
PAGE 32
Section 3: Basic Installation Managing DHCP AXIS 5570e/AXIS 5670e User’s Manual Follow the instructions below to download the IP address using DHCP: 1. Edit or create a scope in the DHCP manager of the DHCP daemon. The entries included in this scope should contain the following parameters: • range of IP addresses • subnet mask • default router IP address • WINS server IP address(es) • lease duration 2. Activate the scope. The AXIS 5570e/AXIS 5670e will automatically download the DHCP parameters.
PAGE 33
AXIS 5570e/AXIS 5670e User’s Manual IP address Section 3: Basic Installation If you do not have a DHCP server on your network, you must obtain an unused IP address from your network administrator. Important: DO NOT use the IP addresses used in the following examples when installing your AXIS 5570e/AXIS 5670e. Always consult your network administrator before assigning an IP address to your AXIS 5570e/AXIS 5670e.
PAGE 34
Section 3: Basic Installation AXIS 5570e/AXIS 5670e User’s Manual Notes: • The host name limitations conclude that if you want to register the same host name at a WINS server and a DDNS server, the host name should be no longer than 15 characters and it should only contain the characters: ‘A - Z’, ‘a-z’ and ‘-’ • Refer to your system manuals or to your network administrator for instructions on how host name resolutions are performed on your system.
PAGE 35
AXIS 5570e/AXIS 5670e User’s Manual Section 4 Section 4: Setting Up - AS/400 (iSeries) Setting Up - AS/400 (iSeries) This section describes how to configure the AXIS 5570e/AXIS 5670e for printing SCS and IPDS data streams using SNA and TCP/IP transport protocols in the AS/400 (iSeries) environment. Note: SNA is only available for print server models with the SNA option installed. Please refer to Product Model Summary, on page 9 A number of protocols and print methods are available.
PAGE 36
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual If you intend to operate your AXIS 5570e/AXIS 5670e in a multiprotocol environment, you should also proceed to the other relevant sections in this manual: Section 5 Setting Up - IBM Mainframe (zSeries), on page 59 Section 7 Setting Up - NetWare, on page 123 Section 6 Setting Up - Windows, on page 101 Section 8 Setting Up - OS/2, on page 117 Section 8 Setting Up - Macintosh, on page 158 Section 9 Setting Up - UNIX, on page 165
PAGE 37
AXIS 5570e/AXIS 5670e User’s Manual The AS/400 Host System Checklist Section 4: Setting Up - AS/400 (iSeries) If you are using AS/400 Version 3 Release 1 or higher, the AS/400 host in 5494 CU mode is automatically configured. The instructions in this section describe this automated configuration procedure. If you are using a pre-version 3 release, you must perform the configuration procedure manually. If this is the case, please refer to the Axis Web site for further documentation.
PAGE 38
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual 3. Press F11 to display keywords. Display Line Description S44A6643 Line description . . .: LIND Option . . . . . . . .: OPTION Category of line . . .: Resource name . . . .: Online at IPL . . . . : Vary on wait . . . . .: Network controller . .: Local adapter address : Exchange identifier . : Ethernet standard . .: Line speed . . . . . .: Enable only for TCP/IP: Current line speed . .: Duplex . . . . . . . .
PAGE 39
AXIS 5570e/AXIS 5670e User’s Manual Section 4: Setting Up - AS/400 (iSeries) 4. For future reference, note the values of the Local Adapter Address (ADPTADR) and Maximum Controllers (MAXCTL) parameters. Press Enter to view the active switched controllers display. Display Line Description Line description . . : LIND Option . . . . . . . : OPTION Category of line . .
PAGE 40
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual 5. Press Enter to display the SSAP list. Make sure that there is at least one SSAP entry dedicated for SNA. For your future reference, note the SSAP value for this entry. Verify that the number of controllers displayed on this screen does not exceed the value for maximum controllers (MAXCTL) from above. Display Line Description S44A6643 Line description .: LIND Option . . . . . : OPTION Category of line .: SSAP List. . . .
PAGE 41
AXIS 5570e/AXIS 5670e User’s Manual Section 4: Setting Up - AS/400 (iSeries) 6. Press Enter to display the Autocreate controller (AUTOCRTCTL) parameter. Ensure that the AUTOCRTCTL parameter is set to *YES. Press F3 to return to the command line. Display Line Description S44A6643 Line description . . : Option . . . . . . . : Category of line . . : LIND OPTION ETHERNET *APPN *ELAN Link speed . . . . .: Cost/connect time . .: Cost/byte . . . . . : Security for line. . : Propagation delay. .
PAGE 42
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual 9. Type DSPSYSVAL QAUTORMT on a command line and press Enter. Make sure the Autoconfigure remote controller parameter is turned on(1). Press F3 to exit. Display System Value System value . . . . . : Description . . . . . : QAUTORMT Autoconfigure of remote controllers Autoconfigure remote controller : 1 0=Off 1=On 10. Type DSPMODD QRMTWSC on the command line and press Enter. Press F11 to display the keywords.
PAGE 43
AXIS 5570e/AXIS 5670e User’s Manual Section 4: Setting Up - AS/400 (iSeries) 11. Type DSPUSRPRF QUSER and press Enter. Make sure that the QUSER Status is *ENABLED. Display User Profile - Basic User profile . . . . . . . . Previous sign-on . . . . . . Sign-on attempts not valid . Status . . . . . . . . . . . Date password last changed . Password expiration interval Set password to expired . . User class . . . . . . . . . Special authority . . . . . Group profile . . . . . . . Owner . . . . . . . . . . .
PAGE 44
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual Use the command WRKCFGSTS *CTL xxxx* (where xxxx is the first 4 characters of the AXIS 5570e/AXIS 5670e 5494 LU Name)and press Enter to delete any previously created Controller and Device descriptions specific to your AXIS 5570e/AXIS 5670e. Delete the Device Descriptions (indented text) first and then the Controllers. Print a test page if you are unsure of the AXIS 5570e/AXIS 5670e 5494 LU Name.
PAGE 45
AXIS 5570e/AXIS 5670e User’s Manual Configuring the AXIS 5570e/AXIS 5670e Section 4: Setting Up - AS/400 (iSeries) To perform the instructions presented in this section, you should first assign an IP address to your AXIS 5570e/AXIS 5670e using one of the methods presented in Setting the IP address, on page 24.
PAGE 46
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual 4. Click the Add Session button. This will start the Configuration Wizard which is a step-by-step guide through the required IBM configuration settings. Notes for SCS printing: • In the Configuration Wizard’s IBM Printer Emulation window, 38xx is the value used for LaserWriter printers and all other values are used for matrix printers.
PAGE 47
AXIS 5570e/AXIS 5670e User’s Manual Verifying the Communication Link Section 4: Setting Up - AS/400 (iSeries) 1. Type WRKCFGSTS *CTL xxxx* on the AS/400 command line (xxxx is the first four characters of the AXIS 5570e/AXIS 5670e 5494 LU Name)and press Enter. After a couple of minutes, ensure that the following items are displayed: • One APPC controller with the same name as the AXIS 5570e/AXIS 5670e 5494 LU Name.
PAGE 48
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual TN5250E printing (SCS over IP) TN5250E is the recommended protocol to use when printing SCS data streams over TCP/IP. This print method offers superior control, management and throughput for the AXIS 5570e/AXIS 5670e. Before you begin Make sure that the AS/400 host is running OS/400 V3R2 or higher with TCP/IP support installed and configured. Make sure that the latest PTFs are installed.
PAGE 49
AXIS 5570e/AXIS 5670e User’s Manual Configuring the AXIS 5570e/AXIS 5670e Section 4: Setting Up - AS/400 (iSeries) Follow the instructions below to configure the AXIS 5570e/AXIS 5670e for TN5250E printing using a Web browser: 1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator. 2. Enter the IP address or the host name of the AXIS 5570e/AXIS 5670e in the location field and press the Enter key on your keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e will appear.
PAGE 50
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual Notes: Verifying the communication link • In the Configuration Wizard, you must choose a new and unused name for the printer (in the ‘Printer Name’ field) when in the ‘TN5250E Protocol Configuration’ window. • In the Configuration Wizard’s ‘Printer Driver’ window, PCL is used for LaserWriter printers, all other values apply to matrix printers. 1.
PAGE 51
AXIS 5570e/AXIS 5670e User’s Manual Section 4: Setting Up - AS/400 (iSeries) PPR/PPD Printing - IPDS data streams Note: IPDS is only available for AXIS 5570e/AXIS 5670e models with the IPDS option installed. For more information, refer to Product Model Summary, on page 9.
PAGE 52
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual 3. Select a name for the PSF configuration and enter it at the PSF configuration (PSFCFG) line. The name may comprise the letters A-Z and the numerals 0-9, but must begin with a letter. A maximum of 10 characters are allowed. 4. Enter QGPL at the Library line. 5. Enter *YES at the IPDS pass through (IPDSPASTHR) line. 6. Enter *NORDYF at the Activate release timer (ACTRLSTMR) line. 7.
PAGE 53
AXIS 5570e/AXIS 5670e User’s Manual Creating a Printer Device Description Section 4: Setting Up - AS/400 (iSeries) Create a printer device description by following the instructions below: 1. Issue the command CRTDEVPRT and press Enter. 2. Press F11 to display keywords. 3. Select a name for the printer device and enter it at the Device Description (DEVD) line. The name may comprise the letters A-Z and the numerals 0-9, but must begin with a letter. A maximum of 10 characters are allowed.
PAGE 54
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual Many of the settings presented in the following panel example can be left at their default settings. However, the settings that you must change are highlighted in bold text and the settings that you must enter exactly as shown in the example are highlighted in bold underlined text.
PAGE 55
AXIS 5570e/AXIS 5670e User’s Manual Section 4: Setting Up - AS/400 (iSeries) Create Device Desc (Printer) (CRTDEVPRT) Type choices, press Enter. Device description . . . . . . . DEVD > AXISPR1 Device class . . . . . . . . . . DEVCLS > *LAN Device type . . . . . . . . . . TYPE > *IPDS Device model . . . . . . . . . . MODEL > 0 LAN attachment . . . . . . . . . LANATTACH > *IP Advanced function printing . . . AFP Port number . . . . . . . . . . PORT Online at IPL . . . . . . . . .
PAGE 56
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual User-defined objects . . . . . . USRDFNOBJ Object . . . . . . . . . . . . Library . . . . . . . . . . Object type. . . . . . . . . . Data transform program . . . . . USRDTATFM > AXISPR1 > QGPL > *PSFCFG *NONE Library. . . . . . . . . . . . User-defined driver program. . . USRDRVPGM *NONE Library. . . . . . . . . . . . Text ‘description’ . . . . . . . TEXT IPDS over PPR/PPD More...
PAGE 57
AXIS 5570e/AXIS 5670e User’s Manual Configuring the AXIS 5470e Section 4: Setting Up - AS/400 (iSeries) Follow the instructions below to configure your AXIS 5570e/AXIS 5670e using a standard Web browser: 1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator. 2. Enter the IP address or the host name of the AXIS 5570e/AXIS 5670e in the location field and press the Enter key on your keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e will appear.
PAGE 58
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual Note for IPDS printing: In the Configuration Wizard, you can choose between PCL or PostScript printing. Choose the printer language that corresponds to your printer. 3. Click the Configuration Wizard for IBM sessions button. 4. Click the Add Session button. This takes you to the Configuration Wizard which is a step-by-step guide through the required configuration settings.
PAGE 59
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Section 5 Setting Up - IBM Mainframe (zSeries) This section describes how to configure the AXIS 5570e/AXIS 5670e for printing SCS, 3270 and IPDS data streams using SNA and TCP/IP transport protocols in the IBM Mainframe (zSeries) environment.
PAGE 60
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual If you intend to operate your AXIS 5570e/AXIS 5670e in a multiprotocol environment, you should also proceed to the other relevant sections in this manual, namely: Section 4 Setting Up - AS/400 (iSeries) Section 7 Setting Up - NetWare Section 6 Setting Up - Windows Section 8 Setting Up - OS/2 Section 8 Setting Up - Macintosh Section 9 Setting Up - UNIX SNA Printing The AXIS 5570e/AXIS 5670e supports printing of SCS, 327
PAGE 61
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Configuring the Mainframe Host System Before you begin These procedures are compulsory for printing in the IBM Mainframe environment. Configuring the host system requires you to do the following: • Make sure that a VTAM Logon-mode entry is available for your AXIS 5570e/AXIS 5670e. • Create the VTAM Definition for the Major Node where the Print Server definition is to be placed.
PAGE 62
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual 2. Add the Print Server PU and LU definitions to the major node definition. For Switched Major Node definitions you need to: • Add the IDBLK (default = E07) and IDNUM (default = last 5 digits of the AXIS 5570e/AXIS 5670e MAC address) entries to the PU definition. • Code a PATH definition using the unit’s full 12 digit MAC address.
PAGE 63
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Logon-mode Entry Creating a VTAM Logon-mode entry for your AXIS 5570e/AXIS 5670e.
PAGE 64
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual Switched major node definitions The example below shows how the print server PU, PATH, and LU definitions may be coded in a switched major node definition. * PU definition * E07xxxxxx is the node ID set in AXIS 5570e/AXIS 5670e.
PAGE 65
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Note: In the PU definition, IDNUM should be set to the five last digits of the AXIS 5570e/AXIS 5670e node address, NODE_ADDR. By default NODE_ADDR stands for the five last digits of the AXIS 5570e/AXIS 5670e serial number.
PAGE 66
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual If the LAN media at the remote (Print Server) location differs from that at the host location (e.g. Remote LAN = Ethernet and Host LAN = Token Ring), the MAC address definitions must be modified, as outlined below: Print Server Modifications: The AXIS 5570e/AXIS 5670e Host MAC address (H1_MAC_ADDR) must be bitorder reversed for each byte, e.g.
PAGE 67
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Configuring the AXIS 5570e/AXIS 5670e To perform the instructions presented in this section, you should first assign an IP address to your AXIS 5570e/AXIS 5670e using one of the methods presented in Setting the IP address, on page 24. The purpose of the configuration of the AXIS 5570e/AXIS 5670e is to emulate a LAN attached IBM 3174 Control Unit running SNA PU2.0.
PAGE 68
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual 4. Click the Add Session button. This will start the Configuration Wizard which is a step-by-step guide through the required configuration settings. Notes for SCS printing: • In the Configuration Wizard’s IBM Printer Emulation window, 38xx is the value used for LaserWriter printers and all other values are used for matrix printers.
PAGE 69
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Verifying the Communication Link Procedures The easiest way to test the communication is by sending a print job to the AXIS 5570e/AXIS 5670e. If there are problems, press the test button once to print the test page where you can find the present SNA link status. 1. Power on the Print Server and wait for 2 minutes. 2.
PAGE 70
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual TCP/IP TN3270E Printing The following procedures describe how to configure the AXIS 5570e/AXIS 5670e for SCS, 3270DS and IPDS printing, using TCP/IP TN3270E.
PAGE 71
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Configuring the AXIS 5570e/AXIS 5670e Follow instructions below to configure the AXIS 5570e/AXIS 5670e using a Web browser: 1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator. 2. Enter the IP address or the host name of the AXIS 5570e/AXIS 5670e in the location field and press the Enter key on your keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e will appear.
PAGE 72
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual Notes for SCS printing: • In the Configuration Wizard, Non-IPDS Printer Emulation uses value structure 38xx for LaserWriter printers. All other values can be used for matrix printers. • In the Configuration Wizard’s Printer Driver window, PCL is used for LaserWriter printers, all other values apply to matrix printers.
PAGE 73
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Microsoft SNA Server Communication is established in two separate stages, SNA Server-toHost connection and SNA Server to AXIS 5570e/AXIS 5670e connection, as described below: SNA Server-to-Host Connection Follow the steps below to set-up a SNA Server-to-Host connection for the AXIS 5570e/AXIS 5670e: 1. Start Microsoft SNA Server Manager and click the Servers folder.
PAGE 74
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual 6. Click OK. SNA Server Manager Main Window SNA Server - AXIS 5570e/AXIS 5670e connection 1. Select the new LUA and drag it to the TN3270 connection definition (highlighted in the SNA Server Manager Window above). 2. Select the properties of the LUA. 3. Click the TN3270 tab in the properties popup window. 4. Select Generic Printer Type. 5. Click the IP Address List tab. 6.
PAGE 75
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Verifying the Communication: 1. Activate the connection you created in step 2 of the above SNA Server - AXIS 5570e/AXIS 5670e connection procedures. The status of the connection should be “active”. 2. Make sure the corresponding LU in the host is activated. 3. Activate the TN3270 connection to the AXIS 5570e/AXIS 5670e. The LUA should change status to SSCP. 4.
PAGE 76
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual 4. Leave the rest at their default settings. Peer PU profile 5. Click the TN3270 icon. The panel below will appear. 6. Select All Available Host PU profiles. 7. Enter the user name, from the User List, that you want all TN3270 clients to use. 8. Specify the maximum number of TELNET connections you want to allow each TN3270 client. 9. Leave the rest at their default settings and click OK.
PAGE 77
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) PU profile name and Logical adapter 10. Press the “insert” key to create a new Host PU Profile. Choose Host PU Profile from the list displayed in the dialog. Then the panel below will appear. Printer LU 11. Enter a unique name as PU profile name. 12. Enter the number of dependent LUs you want for this PU. 13. Enter the starting LU number. 14. Enter the Node ID (the same ID as for item 3 above). 15. Choose logical adapter.
PAGE 78
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual 21. Set Default LU type to Printer (LU type 1 or 3). 22. Specify the VTAM LU name prefix. Click OK. Notes: • When the LUs are created the default names for the Printer Devices will be followed by a two digit number starting at the number you entered in the starting dependent LU number field. • In the example below, eight LUs are created automatically.
PAGE 79
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Profile Name NWSAA Number of local service access points: 2 Enable adapter at startup: Yes PU Profile Name NWSAAPU Number of dependent LUs: 8 Starting dependent LU number: 4 Peripheral node control point name: Node ID (block/PU ID): NWSAAPU 66204 Offline test mode: No Assign only LUs activated by the host: Yes Enable SDDLU Support: No Adapter Name: E100B_1 Adapter Type: 802.
PAGE 80
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual Profile Name NWSAA Yes Enable PU profile at startup: Type Mod Termination Method 14 2 TSELF BRLTST04 1 2 TSELF Public BRLTST05 1 2 TSELF 6 Public BRLTST06 1 2 TSELF 7 Public BRLTST07 1 2 TSELF 8 Public BRLTST08 1 2 TSELF 9 Public BRLTST09 1 2 TSELF 10 Public BRLTST0A 1 2 TSELF 11 Public BRLTST0B 1 2 TSELF LU id Category 0 Public 4 Public 5 VTAM LU Name PU Pro
PAGE 81
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) 2. Send a print job from the host. The AXIS 5570e/AXIS 5670e is now ready for use. If needed, it can be further adapted to your system using the Web-based configuration pages or IBM Printer Emulation. Please refer to Extended IBM Printer Emulation, on page 251. You can check the status of the TN3270E connection by printing a test page from the Print Server. This is done by pressing the test button once.
PAGE 82
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual PPR/PPD Printing - IPDS data streams Important: IPDS is only available for print server models with the IPDS option installed. Please refer to Product Model Summary, on page 9. Before you begin Configuration Procedures In order to use the AXIS 5570e/AXIS 5670e to print IPDS data using TCP/IP as the transport protocol, the following software must be installed and configured on your MVS: • PSF/MVS Version 2 release 2.
PAGE 83
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Specifying the TCP/IP address space name To specify a TCP/IP address space name you should enter the following EXEC statement in the appropriate PSF writer procedure: //STEP01 EXEC PGM=APSPPIEP,REGION=4096K,PARM=(,,,,tcpip_name) where tcpip_name is the name of the TCP/IP address space. If this parameter is not coded, PSF uses the default name TCPIP.
PAGE 84
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual Modifying the TCP/IP profile The TCP/IP profile contains system configuration statements used to initialize the TCP/IP address space.
PAGE 85
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) The table below provides more information about the statements. Statement Explanation DATABUFFERPOOLSIZE Defines the number and size of the data buffers. It is recommended that you specify at least 160 data buffers and a buffer size of 32768 bytes SMALLDATABUFFERPOOLSIZE Defines the number of small data buffers.
PAGE 86
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual Configuring the AXIS 5570e/AXIS 5670e Follow the instructions below to configure your AXIS 5570e/AXIS 5670e using a standard Web browser: 1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator. 2. Enter the IP address or the host name of the AXIS 5570e/AXIS 5670e in the location field and press the Enter key on your keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e will appear.
PAGE 87
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Verifying the communication You can verify the communication between the MVS system and the AXIS 5570e/AXIS 5670e by pinging the print server from the MVS system. A successful ping indicates that the MVS system can communicate with the AXIS 5570e/AXIS 5670e. From an TSO session, enter the following command: TSO PING Note: The IP address is the IP address of the AXIS 5570e/AXIS 5670e.
PAGE 88
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual JES definitions When a TCP-attached printer is to be used with JES, it must be defined for deferred-printing mode. To use a PSF printer for deferred printing under JES, you must first code JES initialization statements to define FSSs and FSAs for PSF printers. For JES2, the FSS is defined by an FSS statement, and the FSA is defined by a PRTnnnn statement.
PAGE 89
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) The following paragraphs describe the JES2 initialization statements shown above, which are typical of the JES2 statements used with PSF. For more detailed descriptions of all JES2 initialization statements, refer to the JES2 initialization and tuning publication for your operating system. FSS Statement: The FSS initialization statement is optional but recommended.
PAGE 90
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual The PRTnnnn parameters create JES2 default values that are used unless other values are specified in the application program JCL. The PRTnnnn statement contains the following parameters: PRTnnnn Statement Explanation CKPTPAGE Specifies the number of pages between data-set checkpoints. If checkpoint intervals are too frequent, printer performance is significantly reduced.
PAGE 91
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) PRTnnnn Statement Explanation PRMODE Specifies the data-set processing modes supported for the printer. It lists all the PRMODE values that the printer accepts. If the AXIS 5570e/AXIS 5670e is connected to a PostScript printer, the correct setting is PRMODE=(PAGE,LINE,).. This setting indicates that composed-page and line data sets can be printed. Enables job-header and job-trailer separator pages to be produced.
PAGE 92
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual The following paragraphs describe the JES3 initialization statements shown above, which are typical of the JES3 statements used with PSF. For more detailed descriptions of all JES3 initialization statements, refer to the JES3 initialization and tuning publication for your operating system. FSSDEF Statement: The FSSDEF initialization statement is optional but recommended.
PAGE 93
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) DEVICE Statement: A DEVICE statement is required for each printer. The DEVICE parameters create JES3 default values that are used unless other values are specified in the JCL application program. The DEVICE statement can contain the following parameters: Device Statement Explanation Specifies the JES default page definition. The value YES specifies that the page definition can be changed during startup procedures.
PAGE 94
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual Device Statement Explanation JUNIT Specifies: 1. The device address (host-connected, channel-attached, non-SNA printers only). Do not specify a device address for the AXIS 5570e/AXIS 5670e when using TCP/IP attachment. 2. The name of the processor to which the device is attached 3. A destination class for messages about the device 4 .Whether the device is initially online or offline This parameter is required.
PAGE 95
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Defining the printer to PSF Each AXIS 5570e/AXIS 5670e must be defined to PSF with a PRINTDEV statement in the PSF startup procedure. The following keywords are required on the PRINTDEV statement: • IPADDR='xxx.xxx.xxx.xxx' • PORTNO='xxxx' The IPADDR parameter specifies the IP address of the AXIS 5570e/AXIS 5670e in dotted-decimal notation. Note: Do not specify a host name in place of the dotted-decimal address.
PAGE 96
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual If you want to print both 240-pel and 300-pel AFP/IPDS jobs, create two separate FSAs, one for jobs with resolution of 120 or 240, and one for jobs with resolution of 300 pels. The 240-pel resolution FSA uses 240-pel resources, and the 300-pel resolution FSA uses 300-pel resources. Both FSAs are defined to drive the same printer; however, only one FSA can be active at one time for a given printer.
PAGE 97
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Example continues CONT... //* REQUIRED ACTIONS = //* RESOLUTION - THIS START PROCEDURE IS SET UP FOR DRIVING //* A TCP/IP DEVICE AT 240 PEL RESOLUTION.
PAGE 98
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual Example continues CONT... //* ************************************************************ //* //* ************************************************************ //PRT1 CNTL //PRT1 PRINTDEV FONTDD=*.FONT01, /* 240 PEL FONT LIBRARY DD //* /* <-- SEE REQUIRED ACTIONS //* /* ABOVE //*PRT1 */ PRINTDEV PRINTDEV FONRDD=*.
PAGE 99
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Although it is not recommended, it is possible to drive the printer with just one FSA, if one of the following conditions are met: • All the resources in the resource libraries are resolution-independent, and all the jobs that use inline resources or user libraries contain resources that are resolution-independent.
PAGE 100
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual When you install PSF, you must create or update the required libraries referenced by the startup procedure, and you should consider any need to increase the region size, as specified in the EXEC statement, to accommodate resources and an increased number of printer FSAs. The startup procedure can also specify defaults that cannot be set with JES initialization statements for printer FSA definitions.
PAGE 101
AXIS 5570e/AXIS 5670e User’s Manual Section 6 Section 6: Setting Up - Windows Setting Up - Windows Having connected the AXIS 5570e/AXIS 5670e to your network, as described in Connecting a printer to the Ethernet Network, on page 20, this section describes how to install the AXIS 5570e/AXIS 5670e in the Windows environment. Identify your Windows platform and follow the installing instructions from the list below.
PAGE 102
Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual If you intend to use the AXIS 5570e/AXIS 5670e in a multiprotocol environment, you should also refer to the following sections: Section 7 Section 8 Section 8 Section 9 Setting Up - NetWare, on page 123 Setting Up - OS/2, on page 117 Setting Up - Macintosh, on page 158 Setting Up - UNIX, on page 165 Adding Printers in Windows 2000/ Windows XP over TCP/IP (LPR) Follow the instructions below to use the standard Windows method for addi
PAGE 103
AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows 2. Select Local Printer attached to this computer. Make sure the Automatically detect and install my Plug and Play printer check box is not checked. Click Next. 3. Click the Create a new port radio button and select Standard TCP/IP Port from the list. Click Next and the Add Standard TCP/IP Printer Port Wizard starts. Click Next.
PAGE 104
Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual 4. Enter the IP address of the print server (Example: 192.168.3.191) The Port Name field will be filled in automatically when you enter the IP address. Add the port you want to use as a suffix (optional): 5570e: Physical Port Add suffix Entry example USB port Type _USB1 192.168.3.191_USB1 LPT1 (parallel port) Type _LPT1 192.168.3.191_LPT1 Physical Port Add suffix Entry example LPT1 (parallel port) Type _LPT1 192.168.3.
PAGE 105
AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows 5. In the Additional Port Information Required window, enter the Device Port you want to use, you will see LPT1, LPT2 and COM1 in a drop-down menu: 5570e: Physical print server port connected to printer Choose port USB port LPT2 LPT1 (parallel port) LPT1 5670e: Physical print server port connected to printer Choose port LPT1 (parallel port) LPT1 LPT2 (parallel port) LPT2 COM1 (serial port) COM1 Click Next.
PAGE 106
Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual Click Next and Finish 6. Select Manufacturer and Printer from the driver list. Click Next.
PAGE 107
AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows 7. Choose whether you want to keep the existing driver or to replace it. If you already have the printer’s driver installed, you will be asked whether to keep it or to replace it. 8. Click Next. Supply a name for the printer and choose whether you want to make it your default printer. Click Next.
PAGE 108
Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual 9. Choose whether you want to share the printer with other network users, print a test page, etc. Select the appropriate radio button and click Next and Finish. 10. Print a test page to verify your installation. You have now completed the installation. ¨ Check www.axis.com/techsup for updates on the ‘tcpmon.
PAGE 109
AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows Adding Printers in Windows 2000/Windows XP using the Microsoft LPR Monitor This section describes how to set up a Windows 2000/XP server for LPR printing over the TCP/IP protocol, using the built-in Microsoft LPR Monitor i.e. Print Services for UNIX. Note: See Alternative Method for LPR Printing, on page 111 for instructions on how to set up printing over LPR without installing Print Services for Unix.
PAGE 110
Section 6: Setting Up - Windows Windows XP: Windows 2000: AXIS 5570e/AXIS 5670e User’s Manual 1. Go to Start | Printers and Faxes and click the Add a Printer icon to start the Add Printer Wizard. Click Next. 1. Go to Start | Settings | Printers and click the Add Printer icon to start the Add Printer Wizard. Click Next. 2. Select the appropriate radio button: Local Printer. Click Next. 3. Click the Create a new port radio button and select LPR Port from the list. Click Next. 4.
PAGE 111
AXIS 5570e/AXIS 5670e User’s Manual Alternative Method for LPR Printing Section 6: Setting Up - Windows If you wish to print over LPR but do not wish to install Print Services for Unix you can do this by changing the printing protocol after having installed the printer using the Standard TCP/IP method, see Adding Printers in Windows 2000/ Windows XP over TCP/IP (LPR), on page 102 for instructions. LPR is chosen by default with this method.
PAGE 112
Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual Adding Printers in Windows NT 4 Using the Microsoft LPR Monitor If you have not already done so, you should perform the TCP/IP basic setup procedures prior to installing a printer for LPR printing. Preparing for LPR Printing In the Control Panel, double-click the Network icon. Select the Services tab. If the TCP/IP Printing entry appears, then TCP/IP is already installed.
PAGE 113
AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows 5. Type the print server’s name or IP address in the field Name or address of server providing lpr (Example: 10.13.6.198). Then enter which port to use in the field Name of printer or print queue on that server according to the table below (Example: USB1). Click OK and then Close. Ports USB port available AXIS 5570e USB1 AXIS 5670e LPT1 Parallel port Serial port LPT1 LPT2 — COM1 6.
PAGE 114
Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual AXIS Print Monitor Software AXIS Print Monitor is the recommended tool to use for network printing in Windows NT, 98 and Me environments. AXIS Print Monitor is available free of charge on www.axis.com AXIS Print Monitor Overview AXIS Print Monitor allows an AXIS 5570e/AXIS 5670e to be connected in the same simple fashion as connecting a local printer. Once installed, it is automatically initialized upon system startup.
PAGE 115
AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows Adding Printers over TCP/IP in Windows NT 4 using AXIS Print Monitor 1. Install AXIS PrintMonitor on all workstations that will print via the print server. AXIS PrintMonitor is available free of charge on www.axis.com 2. To start the Add Printer Wizard, select Settings | Printers from the Start menu and double-click the Add Printer icon. 3. The Wizard asks you to select My Computer or Network printer server.
PAGE 116
Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual Adding NetBIOS/NetBEUI Printers in Windows 2000 using AXIS Print Monitor See to it that the NetBEUI protocol is installed on your client. Follow the procedure below to install Axis Printer Ports from a Windows 2000 workstation: 1. To start the Add Printer Wizard, select Settings | Printers from the Start menu and double-click the Add Printer icon. Start the installation by clicking Next. 2.
PAGE 117
AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows 7. Click the Have Disk... button. Insert the printer driver diskette/CD that was provided with your printer, select the appropriate diskette/CD drive and click OK. 8. Select the printer driver you want to install and click Next. 9. Enter an appropriate name for your printer and click Next. 10. Choose whether you want to share the printer with other network users and click Next. 11.
PAGE 118
Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual 6. Select the AXIS Port you want to add from the list of available ports. The port appears as . (Example: AX100086.LP1). The is taken from the table below. Click OK. Ports available AXIS 5570e AXIS 5670e USB port Parallel port 1 US1 LP1 LP1 Parallel port Serial port 2 — — LP2 CM1 7. Close the Printer Ports window. 8. Click the Configure Port... button.
PAGE 119
AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows Adding Printers in Windows 98 and Me over TCP/IP using AXIS Print Monitor 1. Install AXIS PrintMonitor on all workstations that will print via the Axis print server. 2. Next, start the Windows Add Printer Wizard: select Settings | Printers from the Start menu and double-click the Add Printer icon. 3. After clicking Next in the first dialog, the Wizard asks you to select between Local Printer and Network Printer.
PAGE 120
Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual 12. Click the radio button “other”. Select AXIS Port and then click OK. 13. Select LPR (TCP/IP) as your choice of protocol and click OK. 14. Enter the IP address or the host name of your print server (Example IP address: 192.168.3.191 or host name: AXIS181636). In the Logical Printer Name field, enter the port you wish to use; USB1, LPT1, LPT2 or COM1. 15.
PAGE 121
AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows Adding Printers in Windows 98 and Me over NetBIOS/NetBEUI using AXIS Print Monitor Follow the procedures below to install Axis NetBIOS/NetBEUI printer ports on a Windows 98 workstation, using AXIS Print Monitor: 1. To start the Add Printer Wizard, select Settings | Printers from the Start menu and double-click the Add Printer icon. 2. After clicking Next in the first dialog, the Wizard asks you to select Local printer or Network printer.
PAGE 122
Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual 6. Select the AXIS Printer Port from the Available Ports list. The port names appears as .. Here, is AX followed by the last six digits of the print server’s serial number (e.g. AX100086) and is taken from the table below. Click the Configure Port button. Ports available AXIS 5570e AXIS 5670e USB port Parallel port 1 US1 LP1 LP1 Parallel port Serial port 2 — — LP2 CM1 Example: AX100086.US1 7.
PAGE 123
AXIS 5570e/AXIS 5670e User’s Manual Section 7 Section 7: Setting Up - NetWare Setting Up - NetWare This section describes how to continue the installation of the AXIS 5570e/AXIS 5670e in the NetWare environment. Identify which transport protocol you are running on your network and which installation method you should use.
PAGE 124
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual Setup using NDPS The AXIS 5570e/AXIS 5670e supports Novell Distributed Print Services (NDPS). You can run NDPS over Pure IP (TCP/IP) or IPX/SPX. Before the AXIS 5570e/AXIS 5670e can be installed, make sure that NDPS is installed and a Broker is loaded on your NetWare file server. AXIS 5570e/AXIS 5670e uses the AXIS NDPS Gateway for printing in networks using either IP or IPX as transport protocols.
PAGE 125
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 1. Double-click on the NDPS Manager object you will be using to control the Printer Agents. 2. On the Identification page for the NDPS Manager, click the printer Agent List button. The Printer Agent List dialog will appear. 3. Click New. The Create Printer Agent dialog will appear. 4. Type a name of your choice in the NDPS Printer Agent field: 5. Select the Axis Gateway configuration in the Gateway Type window. 6.
PAGE 126
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 7. In the Select the printer’s type window, choose your printer. If you cannot find the printer, select an appropriate Generic one (PCL, PS, etc) 8. Select TCP/IP (default) or IPX as network protocol. Click Next. 9. You will find the print server in the next window with the printer attached on the connected port.
PAGE 127
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 1. Only the ports with a connected printer show up in this window. If the printer is not in the displayed print list, click Manually specify the print server and do the following: Enter the Print Servers’ IP address in the IP Address Field 2. Choose a port in the Print Server Port field e.g., 192.168.70.
PAGE 128
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual The IPX Addresses for the above printers will appear as: :: i.e.: 01d7e1c2:00408c5ff6a6:400c where 400c, 401c, and 402c are the socket numbers corresponding the LPT1, LPT2, USB1 and COM1 physical ports: LPT1 400c LPT2 401c USB1 401c COM1 402c If the printer is not in the displayed print list, click Manually specify the print server and do the following: 1.
PAGE 129
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 3. Choose a port in the Print Server Port field, e.g. 01d7e1c2:00408c5ff6a6 and LPT1 The port numbers are USB1*, LPT1, LPT2 or COM1. Ports available AXIS 5570e AXIS 5670e *USB1 port Parallel port 1 Parallel port 2 Serial port other/unknown LPT1 — — LPT1 LPT2 COM1 (Example: other/unknown, which stands for the USB1 port.) 4. When done, select your printer and click Finish. 5.
PAGE 130
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 6. Click Continue and OK in the next NDPS window. The new Printer Agent appears in the Printer Agent List window. Check the Status: it should be Idle. 7. Press Cancel to close the NDPS Manager To install the printer on the workstation, See “Installing an NDPS Printer on the Workstation” on page 137.
PAGE 131
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 4. From the Object menu, select Create. The New Object dialog appears. 5. Select NDPS Printer. The Create NDPS Printer dialog appears.
PAGE 132
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 6. Type a name of your choice in the NDPS Printer Name field, e.g. AXIS5FF66A_IPX1 In the Printer Agent Source field, select the source of the Printer Agent. The following options are available: - Create a New Printer Agent. If you select this option, you are asked to select either the Novell Gateway or a third party Gateway. - Printer Agent on Existing NDS Object.
PAGE 133
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 12. Select TCP/IP (default) or IPX as network protocol. 13. Click Next. 14. You will find the print server in the next window with the printer attached on the connected port. Depending on the transport protocol you used when you start the installation, the print server will appear as: • TCP/IP Network protocol: IP Address and Port, e.g. 192.168.70.243 and LPT1 Only the ports with a connected printer will show up in this window.
PAGE 134
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual If the printer is not in the displayed print list: 1. Click Manually specify the print server enter the Print Servers’ IP address in the IP Address Field. 2. Choose a port in the Print Server Port field e.g., 192.168.70.243 and LPT1: The port numbers are USB1*, LPT1, LPT2 or COM1.
PAGE 135
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare The IPX Addresses for the above printers will appear as: :: i.e.: 01d7e1c2:00408c5ff6a6:400c where 400c, 401c, and 402c are the socket numbers corresponding the LPT1, LPT2, USB1 and COM1 physical ports: LPT1 400c LPT2 401c USB1 401c COM1 402c If the printer is not in the displayed print list: 1.
PAGE 136
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 3. Choose a port in the Print Server Port field: e.g.: 01d7e1c2:00408c5ff6a6 and LPT1. The port numbers are USB1*, LPT1, LPT2 or COM1. Ports available AXIS 5570e AXIS 5670e *USB1 port Parallel port 1 Parallel port 2 Serial port other/unknown LPT1 — — LPT1 LPT2 COM1 (Example: other/unknown, stands for the USB1 port.) 4. When done, select your printer and click Finish.
PAGE 137
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 5. Next, select the printer drivers for each client operating system. (Windows 2000, Windows NT4 and Windows 95/98). These drivers will be automatically downloaded to users’ workstations when they install this printer in the future. 6. Click Continue and OK in the next NDPS window. Your printer will appear as an NDS object in the Directory Tree and will offer a full range of network security options.
PAGE 138
Section 7: Setting Up - NetWare Using Novell Printer Manager AXIS 5570e/AXIS 5670e User’s Manual 1. Log in as Admin. 2. On the any workstation, browse to \SYS:PUBLIC\Win32 and start Nwpmw32.exe (Novell Printer Manager). The Novell Printers dialog appears, displaying a list of installed Public or Controlled printers (if any printers have previously been installed on the workstation). 3. From the Printer Manager’s Printer pull down menu, select New. 4. Click Add.
PAGE 139
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 5. The list of available printers shows the NDPS Public Access Printers on the network and the NDPS Controlled Access Printers in you current NDS context. To see the Controlled Access Printers in other context that you have rights to, click the Browse button and select your choice. Click OK. 6. Once selected, click Install. The Novell Printers – Install dialog appears.
PAGE 140
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 7. Click OK. The default driver for that printer is then automatically downloaded. If the printer object does not have a printer driver associated with it, or a driver was not found, you will be prompted to either to choose from a list of printer drivers provided by NDPS or to provide a disk with the appropriate driver. The Novell Printers dialog appears with the new printer, e.g. AXIS5FF6A6_IPX1 in the installed list. 8.
PAGE 141
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 9. Verify by clicking Start - Settings - Printers on the workstation. Using the Add Printer Wizard 1. Click Start on your workstation, select Settings =>Printers. There might be some differences regarding this menu depending of MS Operating System you are running. 2. Start the Add Printer Wizard on the workstation. The Add Printer Wizard dialog will appear. Click Next.
PAGE 142
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 3. Select Network printer and click Next. 4. Click Next again in the Locate Your Printer dialog (Win2000/XP) or press the Browse button (Win9X) 5. Browse to the NDPS Printers. Expand either the NDPS Controlled Access Printers or the NDPS Public Access Printers folder, select your newly installed NDPS printer and follow the instructions. When you have completed these steps, you are ready to start printing.
PAGE 143
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare Notes: • The Public Access print servers are immediately available for everyone on the network • The Axis Gateway Configuration Utility is an installation and configuration tool for NDPS printers in the NetWare environment. The Axis Gateway will appear in NetWare 5.1 and later releases. You can download the Axis Gateway Configuration Utility for use with earlier versions of NetWare from www.axis.com.
PAGE 144
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual When you install Service Pack 6 (16 April 2003) for NetWare 5.1 or later and Service Pack 3 (16 April 2003) for NetWare 6.0 or later, the AXIS LPR Gateway Configuration will automatically be installed and configured on the NetWare Servers and ready for use. The AXIS IPP Gateway Configuration Snap-in for NetWare 6.0 can be downloaded for free from www.axis.com.
PAGE 145
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 5. Map the next available drive (e.g. G:) to the root of volume SYS on your NetWare server. From the temporary directory where axisIPP-snap-in.zip has been unzipped, run the batch file AxisIPP.bat (default G:). If the drive G: is not available, you have to edit the batch file and change the drive to next available one. Check that each line in the batch file is executed without failure. 6.
PAGE 146
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 6. Use a web browser and the local host URL to login into iManager on your NetWare server. 7. Open your browser to the following URL: https://:2200/eMFrame/iManager.html You have to authenticate. 8. Click on iPrint Management on the left pane. 9. Click on Create Printer. 10. Choose a name of your choice for the printer 11. Choose the context where the printer will be installed. 12.
PAGE 147
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 7. Open your browser to the following URL: https://:2200/eMFrame/iManager.html You have to authenticate. 8. Click on iPrint Management on the left pane. 9. Click on Create Printer. 10. Choose a name for the printer. 11. Choose the context where the printer will be installed. 12. Browse for the NDPS Manager and select it. 13. In the Gateway Type drop-down list, choose the Axis LPR Gateway Configuration. Click Next.
PAGE 148
Section 7: Setting Up - NetWare Installing the iPrint Printer using the iPrint Client. AXIS 5570e/AXIS 5670e User’s Manual In order for users to use iPrint, they need to install the Novell® iPrint Client software and a printer. When a user selects a printer to be installed by iPrint, iPrint checks to see if the Novell iPrint Client software is installed and then installs it if necessary. Then the printer driver is downloaded and the printer is installed in the user's Printer folder.
PAGE 149
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare Basic Setup with AXIS NetPilot Install the AXIS NetPilot software on your computer. AXIS NetPilot runs on any of these Windows platforms; Windows 98 and Windows NT. Starting the Installation Follow the instructions below to install the AXIS 5570e/AXIS 5670e with AXIS NetPilot: 1. Start AXIS NetPilot by double-clicking the NetPilot icon, which is located in the folder where you installed AXIS NetPilot. 2.
PAGE 150
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual The IP address Choose the method the AXIS 5570e/AXIS 5670e should employ for obtaining an IP address. DHCP, ARP, RARP, BOOTP and Auto-IP are supported. You can also select to set the IP address manually. Refer to Assigning an IP Address to the Print Server, on page 14 for further information about setting the IP address.
PAGE 151
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare located in the AXIS NetPilot main window. NetWare Network Environment Window The NetWare Network Environment window allows you to connect additional print queues to your AXIS 5570e/AXIS 5670e as well as create new ones. Follow the steps below to gain access to the NetWare Network Environment window: 1. Select the required Network Print Server from the ‘Network Print Server’ folder. 2.
PAGE 152
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 3. Click the Connect... button. The Connect NetWare Print Queues window appears. The AXIS NetPilot Connect NetWare Print Queues window 4. Select the tree or server location of the print queue from the Resources box. 5. Select an existing print queue to connect to the server port, or create a new print queue by clicking on Create Queue... If you have selected an existing queue, advance to step 8.
PAGE 153
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare Notes: • You cannot type or edit the name manually. • Make sure that you have PSERVER.NLM running if you selected Remote Printer Mode in step 8. 10. If you want to define a remote printer number slot manually, check the Manual box and type the desired number in the box. 11. Click the OK button to return to the Network Environments window. Basic Queue-based printing over IP Axis print servers with software version 6.
PAGE 154
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 3. Set the parameters on the NetWare page: • PSERVER NDS Tree (example: NW5TREE) or PSERVER NDS File Server: (example: FILESERVERNAME) • PSERVER NDS Distinguished Name: (example: AXISXXXXXX., where is the container where you want to create your print server) Setting the PSERVER parameters in the AXIS 5570e/AXIS 5670e Web interface. 4.
PAGE 155
AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare Using a Web Browser for Print Server Management, on page 86. If both the IPX and IP protocols are enabled in your network and the print server uses DUAL_STACK (enabled by default) as its network transport protocol, then IPX will be chosen.
PAGE 156
Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual Advantages • NetWare user licences are not required. Limitations • • Lower performance, typically 20 - 70 kbytes/s for NLM. Higher network load. Using Novell Utilities After installing the AXIS 5570e/AXIS 5670e into the NetWare environment, you can manage your AXIS 5570e/AXIS 5670e, using either Novell’s NetWare Administrator, or PCONSOLE.
PAGE 157
AXIS 5570e/AXIS 5670e User’s Manual Print Layout Section 7: Setting Up - NetWare You can view installed AXIS 5570e/AXIS 5670e and their relative print queues for any NetWare Organizational Unit. You can also display summary information by right-clicking on the printer object you want to examine.
PAGE 158
Section 8: Setting Up - Macintosh Section 8 AXIS 5570e/AXIS 5670e User’s Manual Setting Up - Macintosh Having connected the AXIS 5570e/AXIS 5670e to your network, this section now describes how to set up your print server for printing in Mac OS X and earlier Macintosh environments using AppleTalk. If you intend to use the print server in a multi-protocol environment, refer to the chapters pertaining to the respective operating systems in this manual.
PAGE 159
AXIS 5570e/AXIS 5670e User’s Manual Section 8: Setting Up - Macintosh Note: If you want to print using LPR, select: 1. Printers | Add Printer... 2. From the Printer List dialog, select LPR printers using IP. 3. Enter the IP address or host name of the print server in the LPR printer’s Address field. You must uncheck the Use Default Queue on Server check box and enter a Queue Name: Physical ports: USB1, LPT1, LPT2 or COM1 4. Choose a printer driver from the Printer Model list and click Add to finish.
PAGE 160
Section 8: Setting Up - Macintosh AXIS 5570e/AXIS 5670e User’s Manual Choosing a Printer Selecting a Printer The method for choosing a printer varies depending on which version of LaserWriter printer driver you are using. • • Autodetect Printer Type The LaserWriter 7.0 driver assumes that you use a standard PostScript driver, and cannot take advantage of any printer specific features. The LaserWriter 8.0 driver uses PPD files that contain printer descriptions.
PAGE 161
AXIS 5570e/AXIS 5670e User’s Manual Section 8: Setting Up - Macintosh 4. Click the name of the printer you want — the ports are shown as _. Example: AXIS100086_USB1. 5. Click the Close box. This completes the configuration and closes the Chooser. Repeat this procedure for each Macintosh computer on the network using the print server. LaserWriter 8.0 Printer Driver Follow the instructions below to choose a printer: 1. Select Chooser from the Apple menu. 2. Click the LaserWriter 8.0 icon.
PAGE 162
Section 8: Setting Up - Macintosh AXIS 5570e/AXIS 5670e User’s Manual This functionality has backward compatibility with older printers and Macintosh computers, which means that the AXIS 5570e/AXIS 5670e can generate appropriate responses to Macintosh printer queries when the connected printer does not support bi-directional communication. Verifying the Setup You simply need to print a document from the Macintosh computer to verify communication to the chosen printer.
PAGE 163
AXIS 5570e/AXIS 5670e User’s Manual Setting Parameters Section 8: Setting Up - Macintosh In AppleTalk, you can change a limited number of the parameters of the AXIS 5570e/AXIS 5670e.
PAGE 164
Section 8: Setting Up - Macintosh AXIS 5570e/AXIS 5670e User’s Manual Note: Parameters that you do not want to set should be excluded from the text file. Refer to the Parameter list in this manual for information about which values that are valid for each parameter. 7. Print the text file. The settings will be stored in the print server. 8. Open the Chooser and select the printer port you wish to use for printing documents. 9. Close the Chooser.
PAGE 165
AXIS 5570e/AXIS 5670e User’s Manual Section 9 Section 9: Setting Up - UNIX Setting Up - UNIX Print Tools For printer configuration, printtool and printconfig are the most common. How they are invoked depends on which distribution and window manager you use. AIX SMIT is the recommended printing tool. It contains an integrated printer driver list, but does not have printer detection functionality. Instructions: Type the command smit in a Terminal window, then click Print Spooling.
PAGE 166
Section 9: Setting Up - UNIX Red Hat AXIS 5570e/AXIS 5670e User’s Manual printconf is the recommended printing tool. The program contains an integrated printer driver list, but does not have printer detection functionality. Instructions: Type the command printconf-gui in a Terminal window to start the graphical version. You can also run printconf as a text-based application if you do not have the X Window System installed, or if you prefer the text-based interface.
PAGE 167
AXIS 5570e/AXIS 5670e User’s Manual Section 9: Setting Up - UNIX Notes: • A versatile IPP client for UNIX/Linux is CUPS. It can be downloaded from the Common Unix Printing System’s Web site at www.cups.org • If you don't find your specific printer in your distribution, have a look at http://www.linuxprinting.org/database.html Typical Invocation via a Windows Manager Using the Mandrake 8.
PAGE 168
Section 9: Setting Up - UNIX AXIS 5570e/AXIS 5670e User’s Manual version. The same information as was described above will be needed. Note: In Mandrake, even if you type printtool at a shell prompt, will automatically start. printerdrake Debian 3.0 Debian offers a choice between plain LPD, LPRng and CUPS. There are several printer configuration tools in this distribution, e.g. the apsfilter (version 5 or later), which adds support for LPRng and Ghostscript's uniprint driver scheme.
PAGE 169
AXIS 5570e/AXIS 5670e User’s Manual Section 9: Setting Up - UNIX Text fields for the following options appears: Printer name — Enter a unique name for the printer. (The name cannot contain spaces and must begin with a letter. Valid characters are a - z, A - Z, 0 - 9, -, and _. Remote Host — The hostname or IP address of the remote machine to which the printer is attached. Remote Queue and input filter — The remote printer queue and input filter. Click Next to continue.
PAGE 170
Section 9: Setting Up - UNIX AXIS 5570e/AXIS 5670e User’s Manual 4. You can also run printconf as a text based application if you do not have the X Window System installed, or you just prefer the text based interface. To run it, log in as root (or use the command su to temporarily change to the root user), and type the command /usr/sbin/printconf -tui from a shell prompt.
PAGE 171
AXIS 5570e/AXIS 5670e User’s Manual Adding a Remote Unix Printer Section 9: Setting Up - UNIX To add a remote UNIX printer, such as one attached to a different UNIX/Linux system on the same network, click the New button in the main printconf window. Select Unix Printer from the Queue Type menu, and click Next. Enter a unique name for the printer in the Queue Name text field. The printer name cannot contain spaces and must begin with a letter a through z or A through Z.
PAGE 172
Section 9: Setting Up - UNIX AXIS 5570e/AXIS 5670e User’s Manual SuSE 8.0 The printing system on SuSE Linux is based on an apsfilter, with some enhancements; SuSE's apsfilter will recognize all common file formats (including HTML, if html2ps is installed).
PAGE 173
AXIS 5570e/AXIS 5670e User’s Manual Section 9: Setting Up - UNIX AXIS axinstall Script Having performed the basic TCP/IP setup procedures as defined earlier in this manual, you are now able to print in interactive mode using PROS, LPR, FTP or Reverse Telnet protocols. However, if you want to integrate the AXIS 5570e/AXIS 5670e with your host spooler, you can use the Axis automatic installation script axinstall.
PAGE 174
Section 9: Setting Up - UNIX AXIS 5570e/AXIS 5670e User’s Manual FTP version. > ftp npserver connected to npserver. 220 AXIS 5570e/AXIS 5670e FTP Print Server v6.42 March 23 2003 ready. Name (npsserver:thomas): root 331 User name ok, need password Password: pass (not visible) 230 User logged in ftp> get axinstall 200 PORT command successful. 150 Opening data connection for axinstall (192,36,253,4,13,223), (mode ascii). 226 Transfer complete.
PAGE 175
AXIS 5570e/AXIS 5670e User’s Manual Section 9: Setting Up - UNIX Note: NLPRng is not supported by axinstall. The axinstall script will suggest one of the systems listed below when started. If you do not find the suggestion appropriate, then manually select any of the systems listed. 1....SunOS 4 (SUN BSD, Solaris 1.x) 2....SunOS 5 (SUN SYS V, Solaris 2.x) 3....AIX (IBM RS/6000, BULL DPX 20) 4....HP-UX (HP 9000) 5....BOS (BULL DPX 2) 6....DEC OSF/1 (Digital Equipment, Alpha) 7....
PAGE 176
Section 9: Setting Up - UNIX AXIS 5570e/AXIS 5670e User’s Manual Print Methods on TCP/IP Networks The AXIS 5570e/AXIS 5670e supports several different print methods in the TCP/IP environment. axinstall will suggest a print method suitable for your particular UNIX/Linux system, but you might want to use another method depending on your printing requirements (banner pages, status logging, etc). The diagram below shows the alternative data paths taken by some of the UNIX/Linux print methods.
PAGE 177
AXIS 5570e/AXIS 5670e User’s Manual LPD Section 9: Setting Up - UNIX The Line Printer Daemon is a protocol for transferring print jobs between hosts. This is the recommended method for UNIX/Linux systems, but some System V versions do not support LPD. Advantages: Easy to set up — install the AXIS 5570e/AXIS 5670e as a remote queue in System V, or add a remote printer to /etc/printcap using the rm and rp fields (BSD).
PAGE 178
Section 9: Setting Up - UNIX PROS PROS A Advantages PROS A Limitations AXIS 5570e/AXIS 5670e User’s Manual A protocol developed at Axis. Comes in two versions; named pipe (PROS A) and filter (PROS B). The AXIS 5570e/AXIS 5670e appears as a device to the system. This makes all filter and model options available. It provides accounting and status logging. Supports bi-directional printing. The printer information read back can be viewed in a log file.
PAGE 179
AXIS 5570e/AXIS 5670e User’s Manual Section 9: Setting Up - UNIX Alternatively, FTP may be used. It is a good idea to use bsd/ftp_bsd or sysv/ftp_sysv as a starting point. IBM MVS Systems A sample JCL script, jclex, is available in the mvs directory of the print server. It gives an example of how to print a file from an MVS mainframe to an AXIS 5570e/AXIS 5670e using FTP.
PAGE 180
Section 10: Management and Configuration Section 10 AXIS 5570e/AXIS 5670e User’s Manual Management and Configuration The management and configuration tools that are supported by the AXIS 5570e/AXIS 5670e allow you to: Configuration Overview • Change the print server parameters, i.e.
PAGE 181
AXIS 5570e/AXIS 5670e User’s Manual Section 10: Management and Configuration Using a Web browser Once you have established the AXIS 5570e/AXIS 5670e in the TCP/IP environment, as described in Setting the IP address, on page 24, you are free to access the AXIS 5570e/AXIS 5670e Web pages from any standard Web browser. The Web interface of the AXIS 5570e/AXIS 5670e is divided into two modes of operation, User mode and Admin mode. User In User mode, you have no rights to change any parameter settings.
PAGE 182
Section 10: Management and Configuration Accessing the Web Pages AXIS 5570e/AXIS 5670e User’s Manual Follow the steps below to access the internal web pages of the AXIS 5570e/AXIS 5670e: 1. Enter the print server’s IP address (or host name) in the Location/Address field of your Web browser. Press Enter 2. The Printer Overview page will appear. Click the admin button to access the Administration web pages. 3.
PAGE 183
AXIS 5570e/AXIS 5670e User’s Manual Section 10: Management and Configuration Available Services from the User Mode The following services are available from the User mode. A link to the Axis home page is available from this mode. Printer Overview The Printer Overview page contains a section that allows you to view the general parameter setting of the AXIS 5570e/AXIS 5670e, including the print server name and the location of the print server in your organization, if defined.
PAGE 184
Section 10: Management and Configuration Available Services from the Admin Mode This Print Server AXIS 5570e/AXIS 5670e User’s Manual The following services are available from the Admin mode. An additional link to www.axis.com is available from this mode. The This Print Server page contains a section that allows you to view and modify the general parameter setting of the AXIS 5570e/AXIS 5670e, including the print server name, the node address, the password and the base URL.
PAGE 185
AXIS 5570e/AXIS 5670e User’s Manual Section 10: Management and Configuration Print Jobs From the Print Jobs page you can view the status of the current print jobs, including the number of printed bytes and the origin of the print job. You can also view a log of the 20 latest print jobs that includes the user, the printing protocol and the file size. A log that displays the accumulated usage of the connected printers allows you to control the usage of the connected printers.
PAGE 186
Section 10: Management and Configuration Network Settings AXIS 5570e/AXIS 5670e User’s Manual From the Network Settings page you can set all parameters that control the network traffic to and from the AXIS 5570e/AXIS 5670e. You can enable or disable any of the supported network protocols and fine-tune the parameter settings. Admin | Network Settings | Detailed View | TCP/IP If you want to set a static IP address, make sure you first set DHCP, RARP, BOOTP and Auto-IP Enabled to No.
PAGE 187
AXIS 5570e/AXIS 5670e User’s Manual Section 10: Management and Configuration Statistics The Statistics page displays information about the network traffic to and from the AXIS 5570e/AXIS 5670e as well as information about servers and services that are connected or associated with the AXIS 5570e/AXIS 5670e. Help The Help page displays a comprehensive description of the configuration and management activities that can be performed from the internal Web pages of the AXIS 5570e/AXIS 5670e.
PAGE 188
Section 10: Management and Configuration Software Default AXIS 5570e/AXIS 5670e User’s Manual A Software Default will reset all print server parameters and settings to their default values except: • Node address (NODE_ADDR.) • IP Address (INT_ADDR.) • DHCP enabled (DHCP_ENB) • Installed certificate • Private key A Software Default differs from a Factory Default in that the latter is done by pressing the test button in a specific sequence to default/clear all print server parameters to default.
PAGE 189
AXIS 5570e/AXIS 5670e User’s Manual Section 10: Management and Configuration Using AXIS ThinWizard for Print Server Management AXIS ThinWizard software allows you to manage and upgrade multiple Axis products. Using a standard Web browser, you can find, install, monitor, configure and upgrade your Axis print servers remotely in any TCP/IP network. AXIS Thin Wizard 3.0 is Windows 2000 and Windows XP compatible. Installing AXIS ThinWizard AXIS ThinWizard software is available on www.axis.
PAGE 190
Section 10: Management and Configuration AXIS 5570e/AXIS 5670e User’s Manual 4. The AXIS ThinWizard start page now appears in the Web browser. Enter the user id and password you specified during installation and click Log in. 5. The AXIS ThinWizard interface appears: The first time you use AXIS ThinWizard, set the Preferences to reflect your network environment: Select a network group from the list on the Manage Network page. If the list is empty, you must first create a group.
PAGE 191
AXIS 5570e/AXIS 5670e User’s Manual Section 10: Management and Configuration 3. The Create Network Group page opens. Type the name of the network group, enter the IP address ranges and Axis server types that should be included. If you are only interested in managing print servers, deselect all options but the print server option. 4. Click OK to create the network group. You can edit the properties of each network group from the Network Groups page.
PAGE 192
Section 10: Management and Configuration AXIS 5570e/AXIS 5670e User’s Manual Using FTP for Print Server Management Having assigned an IP address to your AXIS 5570e/AXIS 5670e, as described in Setting the IP address, on page 24, you can change the AXIS 5570e/AXIS 5670e parameter settings using the File Transport Protocol (FTP). Editing the config file Follow the instructions below to edit the config file using FTP: 1.
PAGE 193
AXIS 5570e/AXIS 5670e User’s Manual Section 10: Management and Configuration Example: > ftp npserver connected to npserver. 220 AXIS 5570e/AXIS 5670e FTP Print Server v6.30 Dec 16 2000 ready. Name (npserver:thomas): root 331 User name ok, need password Password: pass (not visible) 230 User logged in ftp> get config 200 PORT command successful. 150 Opening data connection for config (192,36,253,4,13,223), (mode ascii). 226 Transfer complete. 8588 bytes received in 0.24 seconds (35.
PAGE 194
Section 10: Management and Configuration Viewing the Account File AXIS 5570e/AXIS 5670e User’s Manual The account file contains data concerning the ten last print jobs. It specifies an internal job number, the user that initiated the job, the protocol and logical printer that was used, current status (Completed, Off-line, or Printing), number of bytes printed, elapsed time and offline time. Follow the instructions below to view the account file using FTP: 1.
PAGE 195
AXIS 5570e/AXIS 5670e User’s Manual Section 10: Management and Configuration Using Telnet Having assigned an IP address to your AXIS 5570e/AXIS 5670e, as described in Setting the IP address, on page 24, you can manage your AXIS 5570e/AXIS 5670e using the Telnet protocol. Viewing the Account File The account file contains data concerning the last ten print jobs.
PAGE 196
Section 10: Management and Configuration AXIS 5570e/AXIS 5670e User’s Manual Example: > telnet npserver Trying 192.36.253.96... Connected to npserver. Escape character is ‘^]’. AXIS 5570e/AXIS 5670e TELNET Print Server v6.30 Dec 16 2000 AXIS 5570e/AXIS 5670e network login: root Password: pass (not visible) AXIS 5570e/AXIS 5670e TELNET Print Server v6.
PAGE 197
AXIS 5570e/AXIS 5670e User’s Manual Viewing the Status file Section 10: Management and Configuration The status command shows which printer port the logical printers are assigned to, and their current status. Follow the instructions below to view the status file using telnet: 1. Log in to the AXIS 5570e/AXIS 5670e by typing: telnet or telnet in a DOS window (Windows and OS/2) or in a UNIX shell. 2. Enter the user id and the password. (The default entries are root and pass.) 3.
PAGE 198
Section 10: Management and Configuration AXIS 5570e/AXIS 5670e User’s Manual Follow the instructions below to perform a hexdump printout for the SNA printing protocol: 1. Log in to the AXIS 5570e/AXIS 5670e by typing: telnet or telnet in a DOS windows (Windows and OS/2) or in a UNIX shell. 2. Enter the user id and the password. (The default entries are root and pass.) 3. Enable the AXIS 5570e/AXIS 5670e to hexdump mode by typing: snahexdump 4.
PAGE 199
AXIS 5570e/AXIS 5670e User’s Manual Section 10: Management and Configuration Using SNMP You can use SNMP (Simple Network Management Protocol) for remotely monitoring and configuring of the AXIS 5570e/AXIS 5670e. All major functions for print servers are supported. General Information SNMP refers to a set of standards for network management, including a protocol, a database structure specification, and a set of data objects. The AXIS 5570e/AXIS 5670e SNMP implementation runs in the TCP/IP environment.
PAGE 200
Section 10: Management and Configuration The AXIS MIB AXIS 5570e/AXIS 5670e User’s Manual The AXIS MIB contains a large number of objects which may be categorized as follows: • Menu objects - used for viewing and changing the AXIS 5570e/AXIS 5670e configuration from the NMS program. Refer to The Parameter List, on page 295. • Printer status and unit administration objects - used for monitoring AXIS 5570e/AXIS 5670e print jobs and storing parameter changes permanently.
PAGE 201
AXIS 5570e/AXIS 5670e User’s Manual Section 10: Management and Configuration Using Novell Utilities After installing the AXIS 5570e/AXIS 5670e into the NetWare environment, you can manage your AXIS 5570e/AXIS 5670e, using either Novell’s NetWare Administrator, or PCONSOLE.
PAGE 202
Section 10: Management and Configuration AXIS 5570e/AXIS 5670e User’s Manual Notification You can use the NetWare Administrator to enable or disable status notification messages for printers connected to the AXIS 5570e/AXIS 5670e, e.g. Busy, Off-line, Out of paper, Paper jam, etc. You can also add or remove print job owners and administrators from the list of persons to be notified.
PAGE 203
AXIS 5570e/AXIS 5670e User’s Manual Section 10: Management and Configuration Configuring the Print Server from an IBM host Once communication with an IBM host has been established, all the AXIS 5570e/AXIS 5670e parameters can be edited by printing a file containing special configuration commands. To start the configuration, the command %CONFIG+ is entered in the file. To protect your settings, a password must be provided. By default, the password is pass.
PAGE 204
Section 10: Management and Configuration AXIS 5570e/AXIS 5670e User’s Manual Select the PCL5 printer driver and disable the NetWare protocol: %CONFIG+ password; PRDRIVER = PCL5; %CONFIG++ NETW_ENB = NO; %CONFIG-SAVE; %CONFIG- (If you have not changed the default password (pass), the password is optional) For parameters requiring more than one value, the values should be separated using a comma.
PAGE 205
AXIS 5570e/AXIS 5670e User’s Manual Section 11 Section 11: Configuration Possibilities Configuration Possibilities This section describes some special features offered by the AXIS 5570e/AXIS 5670e: Autodetect Printer Type, on page 205 AutoIP, on page 206 E-mail Notification, on page 206 Flash Loading of Firmware over the Web, on page 230 IPP (Internet Printing Protocol), on page 207 Logical Printers for Customized Printing, on page 220 Network Speed, on page 230 NetWare Packet Signature Level 1,2,3, on p
PAGE 206
Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual AutoIP In the absence of an IP address management mechanism such as DHCP, the print server will receive a temporary IP address automatically over AutoIP, a method which enables the host to automatically take a linklocal IPv4 address. AutoIP is supported by Windows 98, Me, 2000, XP and Mac OS version 8.5 or higher.
PAGE 207
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities 3. Click OK and exit when done. Important: Check that the SMTP Server and Domain Name parameters in the print server’s internal web pages are correct. This is done in: Admin | Network Settings | Detailed view | TCP/IP IPP (Internet Printing Protocol) Printing over the Internet with IPP (Internet Printing Protocol) is possible with the AXIS 5570e/AXIS 5670e.
PAGE 208
Section 11: Configuration Possibilities IPP Printing Requirements AXIS 5570e/AXIS 5670e User’s Manual Before you print to an IPP printer you need to know: • the http:// address of the print server. • the brand and model of the printer in order to install the appropriate printer driver. Address Schemes for IPP Printers When using IPP printing, you need to know the IP address or host name of your IPP enabled Axis print server.
PAGE 209
AXIS 5570e/AXIS 5670e User’s Manual IPP clients Section 11: Configuration Possibilities An IPP client needs to be installed on your computer together with an appropriate printer driver for proper IPP functionality. The IPP client is a tool that adds destination printers to your printer list. The AXIS 5570e/AXIS 5670e with integrated IPP is compatible with any 1.0 and 1.1 compliant IPP client. The AXIS 5570e/AXIS 5670e presents IPP printer objects to the client, one for each printer port.
PAGE 210
Section 11: Configuration Possibilities Firewall Considerations with IPP How to Print from Windows 98: AXIS 5570e/AXIS 5670e User’s Manual If there are one or more firewalls between the IPP client and the server, you may have to make some changes to the firewall configuration. IPP uses TCP Port 631 for printing, so any firewalls between client and server must be configured to allow bi-directional traffic on that port.
PAGE 211
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities 5. Select the appropriate printer driver corresponding to the destination printer. 6. Specify a name for the printer you wish to add to your printer list. Click Finish. The destination printer will be added to your printer list and you are ready to print using IPP. How to Print from Windows NT: Before you print to an IPP printer you will need to know: • the http:// address of the print server.
PAGE 212
Section 11: Configuration Possibilities Adding an IPP Printer to your Printer List in Windows NT AXIS 5570e/AXIS 5670e User’s Manual 1. Install the Internet Printer Connection software from Hewlett Packard (can be downloaded from the Hewlett Packard Web site) on your computer. 2. Open Start | Settings | Printers. 3. Choose Add Printer. The Add Printer Wizard will start. 4. Next, the Wizard will ask you if you want to install on My Computer or on a Network print server.
PAGE 213
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities 5. In the Available Ports window, click Add Port: 6. The Printer Ports dialog will appear, showing a list of Available Printer Ports. 7. Choose The HP Internet Printer Connection Port and click New Port. 8. The HP Internet Printer Connection will start. Click Next.
PAGE 214
Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual 9. In the IP Address, Host Name or URL field, type the http:// address of the AXIS 5570e/AXIS 5670e to which the destination printer is connected. The URL will automatically appear in the Port Name field as well: Example: http://171.16.5.218:631/LPT1 if you want to address the parallel port or http://171.16.5.218:631/USB1 to address the USB port. Click Next. 10. The Wizard will confirm the information you have entered.
PAGE 215
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities 12. Next, choose a suitable driver for the destination printer and install it. Click Next . 13. You will be asked if you want the newly added printer to be your default printer and if you want to share the printer on your network with other users. Choose the alternatives that suit your printing needs and click Finish to complete the installation.
PAGE 216
Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual 14. The new printer will appear in your Printer window. You are now ready to start printing using IPP. How to Print from Windows 2000/XP Before you print to an IPP printer you will need to know: • the http:// address of the print server. The http:// address contains the IP address or host name of the print server and the printer port name.
PAGE 217
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities 3. The recipient of the print job can collect the print job at the destination printer. Adding an IPP Printer to your Printer List in Windows 2000/XP 1. Choose File | Print from the document you wish to print. 2. In the Select Printer field, click the Add Printer icon. The Add Printer Wizard will start. Click Next. 3. The Wizard will ask you if you want to install a local printer or a network printer.
PAGE 218
Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual 6. The Installation Wizard will ask you to select a printer driver corresponding to the destination printer. Select the printer driver from the list and click OK. 7. The Wizard will ask you if you want the printer to be your default destination printer. Make your choice and click Next to complete the Add Printer Wizard installation.
PAGE 219
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities 8. The new printer is added to your Select Printer window: 9. You are now ready to print using IPP: specify your new destination printer from the printer list and click Print.
PAGE 220
Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual Logical Printers for Customized Printing The AXIS 5570e/AXIS 5670e has a powerful facility for altering the print data. This means that your desired print format can be realized on any type of printer.
PAGE 221
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities Notes: • The examples in this section describe how you can configure the available logical printers using a standard Web browser. If you want to set them directly by editing the config file, just enter the values for the corresponding parameters. • The examples should only be viewed as suggestions how to configure the logical printers. You should, of course, configure them according to the needs of your network.
PAGE 222
Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual 3. Set the parameter Physical Port to USB1. 4. Set the parameter Character Set Conversion to ISO>IBM. 5. Click the OK button. 6. Select the PR2 tab. 7. Set the parameter Physical Port to USB1. 8. Set the parameter Character Set Conversion to DEC>IBM. 9. Click the OK button. The ISO 8859-2 printer data that is sent to logical printer PR1 converts to IBM PC Set 2 and is printed on USB1.
PAGE 223
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities Example: You have an HP LaserJet printer with dual trays, and want to print on pre-printed forms when using the logical printer PR4. The standard forms are taken from the lower tray, and the preprinted forms are taken from the upper tray. The string before print job should contain the command to select the upper tray: EC&l1H (hex 1B 26 6C 31 48).
PAGE 224
Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual 1. From the print server’s internal Web page, select Admin | Logical Printers. 2. Select the PR1 Web page. 3. Enter the string 01 0A 02 0D 0A in the String Substitutions text field. Hex Code Explanation 01 length of the string you want to replace 0A the string you want to replace 02 length of the substitute string 0D 0A the substitute string 4. Click the OK button.
PAGE 225
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities 3. Enter the string 01 0A 02 0D 0A 03 1B 47 31 02 1B 59 in the String Substitutions text field.
PAGE 226
Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual Activate your desired filter by setting the Printer Language Translation (PRx_FILT.) parameter. Example: Follow the instructions below to convert ASCII print data to PostScript for logical printer PR2: 1. From the print server’s internal Web page, select Admin | Logical Printers. 2. Select the PR2 tab. 3. Set the Printer Language Translation parameter to POSTSCR. 4. Click the OK button.
PAGE 227
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities The PostScript font can be any font that is installed in the printer. If no font is specified, Courier will be used. Example: Follow the instructions below to set the PostScript parameters for logical printer PR2: 1. From the print server’s internal Web page, select Admin | Logical Printers. 2. Select the PR2 tab. 3. Set the Printer Language Translation parameter to POSTSCR. 4. Set the PostScript Page Size parameter to LETTER. 5.
PAGE 228
Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual 1. From the print server’s internal Web page, select Admin | Logical Printers. 2. Select the PR1 tab. 3. Set the Physical Port parameter to USB1. 1. Set the Secondary Printer parameter to PR3. 2. Set the Wait On Busy parameter to NO. 3. Click the OK button. 4. Select Admin | Logical Printers and the PR3 tab. 5. Set the Physical Port parameter to LPT2. 6. Click the OK button.
PAGE 229
AXIS 5570e/AXIS 5670e User’s Manual Read Back of information Example: Section 11: Configuration Possibilities The AXIS 5570e/AXIS 5670e support bi-directional printing. The information from the printer is read back on the parallel port when the parameter Read Back Port (PRx_IN.) has the default setting of AUTO. However, it is required that the printer also supports bidirectional printing. Please refer to your printer documentation for further details regarding bi-directional printing support.
PAGE 230
Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual Network Speed With the Network Speed parameter you can manually specify the speed at which you will send and receive network packages. You can change the Network Speed setting to correspond to the type of network you are using (10 or 100 Mbit). To change the Network Speed in an Ethernet network, log in to the print server’s internal Web pages and click Admin | General Settings =>Change.
PAGE 231
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities Secure Web Services — SSL/TLS In a new and unconfigured AXIS 5570e/AXIS 5670e, SSL/TLS is disabled. Certificates To use SSL/TLS you have to create or obtain a digital certificate. There are two kinds of certificates: self-signed certificates and third party certificates. • Self-signed certificates are less secure but normally they are sufficiently secure for small networks with no public access.
PAGE 232
Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual Enter the data asked for: • Country Name: Example: US • State or Province Name: Example: California • Locality Name: Example: Los Angeles • Organization Name: Example: Printers Inc • Organizational Unit Name: Example: Sales Dept • Common Name*: Example: printserver2@company.
PAGE 233
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities Click Finish and the print server will generate a public/private key pair as well as the self-signed certificate itself (this process will take a few minutes) and store these data in the print server. When the certificate is generated, the print server automatically loads it into your present browser session. The browser reports the new state by changing into https mode.
PAGE 234
Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual Importing a Certificate When you receive the PEM-encoded certificate from your Certificate Authority, open the print server’s Web interface and select Admin | Security Settings. Click Import and follow the instructions on the screen. https:// Whenever SSL/TLS is enabled, you can only reach the print server’s Web interface through the secure services.
PAGE 235
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities Important: To ensure maximum security, it is highly recommended that you change your Administrator password after generating a certificate and disabling insecure protocols! This is done from Admin | General Settings | Change => | General | Root Password.
PAGE 236
Section 12: Upgrading the Firmware Section 12 AXIS 5570e/AXIS 5670e User’s Manual Upgrading the Firmware Upgrading the Firmware You can upgrade the AXIS 5570e/AXIS 5670e firmware using one of the following methods: • • • AXIS ThinWizard (TCP/IP) From the print server’s internal Web pages (TCP/IP) FTP (TCP/IP) Note: Updating instructions are supplied with the firmware release notes.
PAGE 237
AXIS 5570e/AXIS 5670e User’s Manual Section 12: Upgrading the Firmware 1. Click the Firmware button. The Firmware Wizard starts. 2. Browse through the upgrading tips and click Next > when you are done. Select Latest Available Version. Click Next >. 3. Select the servers you want to upgrade, by checking the correct upgrade boxes. Click Next >. 4. Enter the default User ID and Password of the servers you selected in the previous step.
PAGE 238
Section 12: Upgrading the Firmware Upgrading using FTP AXIS 5570e/AXIS 5670e User’s Manual To upgrade over the network using FTP you will need a file with the new print server firmware. The name of this file is in the form product_version.bin. You can use any of the previously mentioned methods to obtain the new file. You must assign an IP address to the AXIS 5570e/AXIS 5670e before you can use this upgrading method. Caution! Be careful not to interrupt the file transfer.
PAGE 239
AXIS 5570e/AXIS 5670e User’s Manual Section 12: Upgrading the Firmware 6. Connect to the print server using ftp. Type ftp 10.13.4.105 (Example using print server IP address 10.13.4.105) 7. Type root after "User:", press Enter. Type pass after "Password:" (your entry will not be visible) press Enter. 8. Change to binary mode transfer. Type bin HASH (or binary HASH) and press Enter. 9. Use the 'put' command to upload the upgrade file to the flash location: (Example using firmware named 5570e_v2_6_42.
PAGE 240
Section 13: SNA Parameter Overview Section 13 AXIS 5570e/AXIS 5670e User’s Manual SNA Parameter Overview This appendix provides summary information on the parameters that control the basic operation of the SNA communication and the IBM printer emulation. It also describes how these parameters may be changed. An overview of how parameters are mapped during the autoconfiguration process is also provided. Refer to the Parameter List document on www.axis.
PAGE 241
AXIS 5570e/AXIS 5670e User’s Manual Parameter Summary Section 13: SNA Parameter Overview The following tables summarize SNA host communication parameters that must be considered when installing the AXIS 5570e/AXIS 5670e.
PAGE 242
Section 13: SNA Parameter Overview AXIS 5570e/AXIS 5670e User’s Manual Mainframe Specific Parameters Parameter Name Default NODE_ID Node ID E07xxxxx, where "xxxxx" are the last five digits of the Print Server’s MAC address. This is the SNA PU identification. The first 3 digits is the IDBLK and the last five is the IDNUM. When defining a VTAM Switched Major Node, this parameter should match the IDBLK and IDNUM values specified in the PU definition.
PAGE 243
AXIS 5570e/AXIS 5670e User’s Manual Section 13: SNA Parameter Overview Updating parameters This is most easily done from the internal web pages of your AXIS 5570e/AXIS 5670e. To set the parameters using a Web browser, you first need to assign an IP address to the AXIS 5570e/AXIS 5670e. For instructions on how to do this, refer to Setting the IP address, on page 24. Alternatively, you can update the parameters via FTP, TFTP or by using extended IBM printer emulation.
PAGE 244
Section 13: SNA Parameter Overview AXIS 5570e/AXIS 5670e User’s Manual To set the parameters to their default values, enter the following in your document and print it. %CONFIG+ password (If you have not changed the default password (pass), the password is optional.
PAGE 245
AXIS 5570e/AXIS 5670e User’s Manual Section 13: SNA Parameter Overview Auto-configuration and Mapping The configuration created in the AS/400 and the mapping to the AXIS 5570e/AXIS 5670e as a result of the auto-configuration process is illustrated by the figure below. Configuration in the AXIS 5470e LU 6.
PAGE 246
Section 13: SNA Parameter Overview AXIS 5570e/AXIS 5670e User’s Manual Printer devices will be named "A201PRT01", A201PRT02", A201PRT02"… The designation "PRTnn" corresponds to the logical printers in the Print Server, i.e. printer device "A201PRT01" will be mapped to Logical Printer #1. By default, all Logical Printers are mapped to the Physical Port LPT1. To customize the print server, proceed to the SNA Printing - 5494 Mode, on page 36.
PAGE 247
AXIS 5570e/AXIS 5670e User’s Manual Section 14 Gateway Configuration, 3174 CU mode Pass-through gateway Section 14: SNA Gateways SNA Gateways Some hints specific to SNA gateways are given below. • AXIS 5570e/AXIS 5670e appears to a gateway as a Down Stream Physical Unit (DSPU), with eight LUs, 1 to 8 (LU 1 may not be available). • Only gateways that communicate with DSPUs using SNA over LLC type 2 are supported.
PAGE 248
Section 14: SNA Gateways Concentrator gateway, general AXIS 5570e/AXIS 5670e User’s Manual A concentrator gateway typically behaves as a PU (or a few PUs) to the host, even though a number of PUs may be available downstream. If it is an SDLC or channel attached gateway, typically only one SDLC or sub-channel address will be used. Examples of concentrator gateways are: IBM Communications Manager/2 (OS/2), Novell NetWare for SAA (NetWare 3.x), Microsoft SNA Server (Windows NT), etc.
PAGE 249
AXIS 5570e/AXIS 5670e User’s Manual Section 14: SNA Gateways 5. Configure PU and LUs. On the Configure PU Profile screen you can set default LU attributes, starting dependent LU address, number of dependent LUs, give CP a name, enable off-line test mode, status assignment of LUs activated by host, status call host at workstation attach, status PU profile start-up and logical adapter name.
PAGE 250
Section 14: SNA Gateways AXIS 5570e/AXIS 5670e User’s Manual 3. Select host connection and assign one or more DownStream LUs to it. 4. Select downstream connection and associate the DownStream LUs (from step 3) with that connection. 5. If necessary, reorder the DownStream LU numbers, that is, the LU numbers used by the downstream system. 6. To connect multiple PUs (boxes) repeat steps 2-5.
PAGE 251
AXIS 5570e/AXIS 5670e User’s Manual Section 15 Section 15: Extended IBM Printer Emulation Extended IBM Printer Emulation When printing from an IBM host, the AXIS 5570e/AXIS 5670e allows you to make use of the following printer functions not found in standard IBM printers: • Configuration Mode • Hex Transparency • User Defined Strings • String Substitutions • Bar Codes • Font Selection. This appendix provides a brief overview of some of these functions.
PAGE 252
Section 15: Extended IBM Printer Emulation Font Selection AXIS 5570e/AXIS 5670e User’s Manual Fonts can be selected directly by FGID (Extended Emulation commands or SCS SFG commands) or indirectly by pitch SCS SCD/SPD commands. Notes: Hex Transparency • SFG control code is only supported by Twinax page printer emulations • Matrix printers only support a few fonts The Transparency function allows you to send ASCII data to the printer directly from the host application.
PAGE 253
AXIS 5570e/AXIS 5670e User’s Manual Section 15: Extended IBM Printer Emulation Before the bar codes can be printed, a bar code format has to be defined. This format sets the type and size of the bar code to be printed. Up to 16 formats can be predefined. The definitions are made by setting up the BAR parameter.
PAGE 254
Section 15: Extended IBM Printer Emulation AXIS 5570e/AXIS 5670e User’s Manual To set up the BAR parameter, use the %CONFIG command in your document. To print bar codes, bar code commands may be included anywhere in your documents. They begin with ‘percent-slash’ (%/) followed by the word BAR. Then follows the number of the bar code definition to be used, a comma, and the sequence to be printed. The command is ended by a semi-colon (;).
PAGE 255
AXIS 5570e/AXIS 5670e User’s Manual Section 16 Font Selection, Coax Printer Emulations Section 16: IBM Fonts IBM Fonts Fonts can be indirectly selected by the IBM system using pitch selection (CPI). In order to gain full access to the fonts the AXIS 5570e/AXIS 5670e offers an alternative font selection command. Please note that matrix printers only support a few fonts. Font selection commands may be included anywhere in your documents.
PAGE 256
Section 16: IBM Fonts Available Fonts AXIS 5570e/AXIS 5670e User’s Manual The fixed pitch fonts are not scalable. If a Point Size is specified, it will be used to compress or expand the character spacing. (%/FONT 11,105; will compress the 10 CPI font to 10.5 CPI without changing the size of the characters).
PAGE 257
AXIS 5570e/AXIS 5670e User’s Manual Pitch 12 CPI Fonts Pitch 13.
PAGE 258
Section 16: IBM Fonts AXIS 5570e/AXIS 5670e User’s Manual Pitch 20 CPI Fonts 281 Gothic Text 20 Pitch 25 CPI Fonts 289 Gothic Text 25 Pitch 26.
PAGE 259
AXIS 5570e/AXIS 5670e User’s Manual Proportional Typographic Fonts (Scalable - User Defined FGIDs) Section 16: IBM Fonts FGID IBM Font Name 3840 CG Times 3841 CG Times Bold 3842 CG Times Italic 3843 CG Times Bold Italic 3844 CG Omega 3845 CG Omega Bold 3846 CG Omega Italic 3847 CG Omega Bold Italic 3848 Coronet 3849 Clarendon Condensed 3850 Univers Medium 3851 Univers Bold 3852 Univers Medium Italic 3853 Univers Bold Italic 3854 Univers Medium Condensed 3855 Univers Bold
PAGE 260
Section 16: IBM Fonts AXIS 5570e/AXIS 5670e User’s Manual Proportional Typographic Fonts (Scalable - User Defined FGIDs) Proportional Typographic Fonts (Scalable Point Size) 3863 Garamond Kursiv 3864 Garamond Kursiv Halbfett 3865 Marigold 3866 Albertus Medium 3867 Albertus Extra Bold 3868 Arial 3869 Arial Bold 3870 Arial Italic 3871 Arial Bold Italic 3872 Times New 3873 Times New Bold 3874 Times New Italic 3875 Times New Bold Italic 3876 Symbol 3877 Wingdings FGID IBM
PAGE 261
AXIS 5570e/AXIS 5670e User’s Manual (cont.
PAGE 262
Section 17: IBM Print Formatting Section 17 AXIS 5570e/AXIS 5670e User’s Manual IBM Print Formatting This appendix provides general parameter information relating to non-IPDS IBM print formatting. IBM Printer Emulation Coax Printer Emulations Mainframe The following tables display the valid printer emulations that can be used in coax and twinax printer emulations.
PAGE 263
AXIS 5570e/AXIS 5670e User’s Manual Section 17: IBM Print Formatting Twinax Printer Emulations AS/400 Parameter Name PREMUL 3816_cx System Languages Default Printer Emulation Options Printer Description 3812_tx IBM 3812 model 1 and 2 page printer 3816_tx IBM 3816 models 01S and 01D, page printer with 5219 diskette 4214_tx IBM 4214 model 2 matrix printer 5224_tx IBM 5224 models 1 and 2, matrix printer 5225_tx IBM 5225 models 1 through 4, matrix printer 5256_tx IBM 5256 models 1 through 3,
PAGE 264
Section 17: IBM Print Formatting AXIS 5570e/AXIS 5670e User’s Manual Coax mode Mainframe Parameter Name SYSL Default 37 US English Value Description Value User defined system language *37 US English, Portuguese Alternate and Canadian Bilingual 833 Korean (Jamo) 256 International Set 1 836 Chinese 260 Canadian French 838 Thai 273 Austrian/German 870 East Europe 274 Belgian 871 Icelandic 275 Brazilian 892 OCR-A 277 Danish/Norwegian 893 OCR-B 278 Swedish/Finnish 114
PAGE 265
AXIS 5570e/AXIS 5670e User’s Manual Section 17: IBM Print Formatting Twinax mode AS/400 Parameter Name SYSL Default 37 US English Value Description Value User defined system language 37 US English, Portuguese Alter-nate and Canadian Bilingual 281 Japanese English 256 New Spanish Word Processing 282 Portuguese 273 Austrian/German 284 Spanish and Spanish Speaking 274 Belgian 285 UK English 275 Brazilian 297 French Azerty 277 Danish/Norwegian 500 Internat.
PAGE 266
Section 17: IBM Print Formatting Paper Size The parameters take two values, orientation and paper size. The following tables describe the paper sizes that can be used in coax and twinax mode. Parameters BIN1 - BIN 6, MANUAL, ENVELOPE, CONTINUOUS Paper Orientation AXIS 5570e/AXIS 5670e User’s Manual Default LETTER Printer Emulation Options Printer Description EXEC 7.25 × 10.5 inches LETTER 8.5 × 11 inches LEGAL 8.5 × 14 inches A4 210 × 297 mm (8.27 ◊ 11.
PAGE 267
AXIS 5570e/AXIS 5670e User’s Manual Section 17: IBM Print Formatting Notes: COR printouts require a Laser Printer with the following characteristics: ASCII Printer Driver • Landscape orientation • Vertically compressed to 70% • Horizontally compressed by using a font of higher character density • Top and left margins of 0.5 inches each by default This parameter should match the printer type you have connected to your AXIS 5570e/AXIS 5670e.
PAGE 268
Section 18: IPDS Overview Section 18 AXIS 5570e/AXIS 5670e User’s Manual IPDS Overview This section describes: • IPDS parameter settings • IPDS fonts IPDS Parameter Settings Before printing IPDS data streams, the basic parameters should be set.
PAGE 269
AXIS 5570e/AXIS 5670e User’s Manual Section 18: IPDS Overview Code page System language *37 US English, Portuguese Alternate and Canadian Bilingual 256 International set 1 259 Symbols set 7 260 Canadian French 273 Austrian/German 274 Belgian 275 Brazilian 277 Danish/Norwegian 278 Swedish/Finnish 280 Italian 281 Japanese English 282 Portuguese 284 Spanish and Spanish Speaking 285 UK English 286 Austrian/German Alternate 287 Danish/Norwegian Alternate 288 Swedish/Finnish A
PAGE 270
Section 18: IPDS Overview AXIS 5570e/AXIS 5670e User’s Manual The Euro character is implemented in the Code Pages 1140 - 1149: Code page System language - Latin 1 EBCDIC Publishing 1140 US English, Canadian English, Canadian French, Netherlands, Brazil, Portugal 1141 Austrian, German 1142 Danish, Norwegian 1143 Finnish, Swedish 1144 Italian 1145 Castilian Spanish, Latin, American Spanish 1146 UK English 1147 French 1148 Multinational ECECP, Belgian, French, Belgian Dutch, Switzerla
PAGE 271
AXIS 5570e/AXIS 5670e User’s Manual Section 18: IPDS Overview Code page System language - Latin 2/3/4/5 EBCDIC and ASCII 852 Croatian, Czech, East German, Hungarian, Polish, Romanian, Slovak, Slovenian 912 Latin 2 ISO/ ANSI 8 Bit 853 Latin 3 Multilingual PC 905 Latin 3 Multilingual 1069 Latin 4 EBCDIC 914 Latin 4 ISO/ASCII 857 Latin 5 PC 920 Latin 5 ISO/ANSI 8 Bit 1026 Latin 5 Code page System language - Latin 9 EBCDIC and ASCII 923 Latin 9 924 Latin 9 EBCDIC 271
PAGE 272
Section 18: IPDS Overview IPDS Configuration AXIS 5570e/AXIS 5670e User’s Manual The basic IPDS parameters are set from the IBM Emulators | Detailed view (IBM IPDS Emulator Settings) page: Enter the configuration settings for the parameters described below. When you are finished, click OK at the bottom of the page to save your settings to the print server. True Color Support The Color Support setting determines how color information is to be interpreted.
PAGE 273
AXIS 5570e/AXIS 5670e User’s Manual Optimize Duplex Section 18: IPDS Overview Use this option to optimize duplex print jobs. Optimization means that sheets are printed in simplex if the reverse side of the sheet is empty, resulting in higher throughput. Important: Some printers will internally turn the sheet upside down when duplex is used. This may cause undesired effects when using pre-printed forms.
PAGE 274
Section 18: IPDS Overview Loaded Font Smoothing AXIS 5570e/AXIS 5670e User’s Manual A downloaded 240 dpi font may appear jagged when printed on a 300 dpi printer. The AXIS 5570e/AXIS 5670e uses a font smoothing feature to enhance the appearance of these fonts. The font smoothing may be disabled if you want to speed up the font loading or if your printer has insufficient PostScript virtual memory. Loaded font smoothing is Enabled by default.
PAGE 275
AXIS 5570e/AXIS 5670e User’s Manual Section 18: IPDS Overview IPDS PCL Configuration Click the IPDS PCL Driver Settings tab and enter the configuration settings for the parameters as described below. When you are finished, click OK at the bottom of the page to save your settings to the print sever. Language version Select the correct PCL language version depending on your connected printer. Symbol set Select the preferred symbol set from the drop-down list.
PAGE 276
Section 18: IPDS Overview AXIS 5570e/AXIS 5670e User’s Manual IPDS Fonts This section describes how IPDS fonts are handled by the AXIS 5570e/AXIS 5670e. There are two different approaches to font handling: • downloading fonts from the host. • using fonts that are already resident in the printer. Both methods are supported by the AXIS 5570e/AXIS 5670e. Host Downloaded fonts IPDS provides functions for downloading fonts from the host computer.
PAGE 277
AXIS 5570e/AXIS 5670e User’s Manual Section 18: IPDS Overview The FGIDs are grouped according to the following table: FGID (hex) FGID (dec) TYPE 0001 - 0041 1 -65 0042 - 0099 66 - 153 12 CPI 009A - 00C8 154 - 200 Proportional PSM 00C9 - 00D2 201 - 210 13 CPI 00D3 - 00EF 208 - 239 15 CPI 00F0 - 00F7 240 - 247 5 CPI 00F8 - 0103 248 - 259 17 CPI 0104 - 0111 260 - 273 8 CPI 0112 - 0117 274 - 279 17 CPI 0118 - 011B 280 - 283 20 CPI 011C - 0120 284 - 288 25 CPI 0121 - 012B 28
PAGE 278
Section 18: IPDS Overview AXIS 5570e/AXIS 5670e User’s Manual Typographical Fonts This section deals with font width selections for typographical (proportional pitch) fonts. Note that when an unsupported typographical font (FGID range 512 65534) is selected, the resulting font will be a fixed pitch and the selected font width value will be ignored.
PAGE 279
AXIS 5570e/AXIS 5670e User’s Manual Section 19 Section 19: DBCS Support DBCS Support The AXIS 5570e/AXIS 5670e supports Double-Byte Character Set (DBCS) for SNA and TN5250E printing. This facilitates printing from an IBM AS/400 host system for languages employing double-byte character sets.
PAGE 280
Section 19: DBCS Support AXIS 5570e/AXIS 5670e User’s Manual Configuring the AXIS 5570e/AXIS 5670e A number of printer emulations exist for DBCS printing. To set the correct system language and printer driver, refer to the tables below and enter the values in the IBM Configuration Wizard.
PAGE 281
AXIS 5570e/AXIS 5670e User’s Manual Section 19: DBCS Support Important: To protect the admin pages and the Configuration Wizard from unauthorized use, enter a password (default Pass) in the Root Password field under admin | General Settings. 3. Click the Configuration Wizard for IBM sessions button. 4. Click the Add Session button. This will start the Configuration Wizard which is a step-by-step guide through the required IBM configuration settings.
PAGE 282
Section 19: DBCS Support AXIS 5570e/AXIS 5670e User’s Manual Amending Device Features After automatic setup, it may be necessary to change the Device features and Last Code Point of the printer device. Failure to do so may cause corruption within your print data. Follow the instructions below, to set the appropriate Device features and Last Code Point for your chosen printer device: 1.
PAGE 283
AXIS 5570e/AXIS 5670e User’s Manual Section 19: DBCS Support Extended IBM Printer Emulation Extended emulation will only work in SBCS mode. Before entering extended emulation you will have to change to single byte mode by sending shift in.
PAGE 284
Section 19: DBCS Support AXIS 5570e/AXIS 5670e User’s Manual 50005 MS Mincho 15 CPI 50105 SimSun 15 CPI 50017 MS Mincho 15 CPI 50117 SimSun 15 CPI 50009 MS Mincho 17.1 CPI 50109 SimSun 17.1 CPI 50020 MS Mincho 17.1 CPI 50120 SimSun 17.1 CPI 50006 MS Mincho 18 CPI 50106 SimSun 18 CPI 50018 MS Mincho 18 CPI 50118 SimSun 18 CPI 50010 MS Mincho 18.9 CPI 50110 SimSun 18.9 CPI 50021 MS Mincho 18.9 CPI 50121 SimSun 18.9 CPI 500111 MS Mincho 21.
PAGE 285
AXIS 5570e/AXIS 5670e User’s Manual Section 19: DBCS Support 50038 HanYang 14.3 CPI 50138 Compst 14.3 CPI 50049 HanYang 14.3 CPI 50149 Compst 14.3 CPI 50034 HanYang 15 CPI 50134 Compst 15 CPI 50035 HanYang 15 CPI 50135 Compst 15 CPI 50047 HanYang 15 CPI 50147 Compst 15 CPI 50039 HanYang 17.1 CPI 50139 Compst 17.1 CPI 50050 HanYang 17.1 CPI 50150 Compst 17.
PAGE 286
Section 20: Digital Copier Support Section 20 AXIS 5570e/AXIS 5670e User’s Manual Digital Copier Support The logical printers support the printing options available on digital copiers and multi-functional printers. It is recommended that you configure the eight logical printers (PR1-PR8) to allow for eight different combinations of the following options to suit your printing needs.
PAGE 287
AXIS 5570e/AXIS 5670e User’s Manual Copier Hole Punch Copier Paper Source Copier Copies Section 20: Digital Copier Support • Left 2 i.e. two staples on the left hand side of the document. • Center 2 i.e. two staples set in the center of the page. This option is intended for documents printed in A3 format. The staples are placed in the center of the page where the document is to be folded. Please refer to the documentation of your digital copier for more information on these features.
PAGE 288
Section 21: Test Button Section 21 AXIS 5570e/AXIS 5670e User’s Manual Test Button The test button is located on the front right hand side of the AXIS 5570e/AXIS 5670e and is used for: • Printing a test page, checking the connection to the printer. • Printing a parameter list, showing the AXIS 5570e/AXIS 5670e current settings. • Resetting the AXIS 5570e/AXIS 5670e parameters to the factory default settings. The Test Page Press the test button once to print a test page.
PAGE 289
AXIS 5570e/AXIS 5670e User’s Manual Section 21: Test Button 4. Restart the AXIS 5570e/AXIS 5670e by disconnecting and reconnecting the external power supply. Important! All parameters are reset to their default values when performing a factory default with the test button. Installed certificates and keys are not affected by a factory default.
PAGE 290
Section 22: Technical Specifications Section 22 AXIS 5570e/AXIS 5670e User’s Manual Technical Specifications Refer to the ‘Parameter List’ document on www.axis.com for a complete description of the Axis print server parameters. Supported Printers: IBM Capabilities Support for all printers and copiers except host-based printers such as Windows GDI.
PAGE 291
AXIS 5570e/AXIS 5670e User’s Manual Supported systems: Section 22: Technical Specifications • Microsoft Windows: 98, Me, NT, 2000, XP and 2003 Server • Novell NetWare: 3.X, 4.X, 5.X, 6.X. Supports bindery and NDS mode. Supports user messages and printer status. NDPS supported over IP and IPX. Support for iPrint using both LPR and IPP protocols. PSERVER (IP/IPX), RPRINTER/NPRINTER supported • Apple MacOS 7, 8, 9, MacOS X version 10.
PAGE 292
Section 22: Technical Specifications AXIS 5570e/AXIS 5670e User’s Manual Copiers Each logical printer port can be configured to activate a number of finishing options in the digital copier. Please visit the support pages at www.axis.com for a list of supported copiers.
PAGE 293
AXIS 5570e/AXIS 5670e User’s Manual Printer Connection Section 22: Technical Specifications • Parallel: 36-pin Centronics connector, highspeed IEEE 1284 compliant with ECP support and throughput of 1 MB/sec • USB: USB 1.1 Low and Full speed. Successfully tested with USB 2.0 Printers • Serial: 9-pin DSUB connector, RS-232, XON/ XOFF or RTS/CTS, data rates up to 115.
PAGE 294
Section 22: Technical Specifications Approvals AXIS 5570e/AXIS 5670e User’s Manual • EMC: EN 55022/1998, EN 55024:1998, EN 61000-3-2, EN 610003-3, VCCI Class B, CTICK AS/NZS 3548, Compliance to FCC part 15 Subpart B, Class B • Safety: EN 60950
PAGE 295
AXIS 5570e/AXIS 5670e User’s Manual Section 23 Section 23: The Parameter List The Parameter List This appendix provides an overview of the AXIS 5570e/AXIS 5670e parameters. You can download the latest technical information on www.axis.com The Config File The left-hand column shows the parameters (default values) as they appear in the internal Web pages. After you have changed them, most parameters take effect for the next print job.
PAGE 296
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual TN3270E_IR. : 0 TN3270E_1. : OFF, 0 0 0 0, 23, PR1, 1, AXPR1 TN3270E_2. : OFF, 0 0 0 0, 23, PR2, 2, AXPR2 TN3270E_3. : OFF, 0 0 0 0, 23, PR3, 3, AXPR3 TN3270E_4. : OFF, 0 0 0 0, 23, PR4, 4, AXPR4 TN3270E_5. : OFF, 0 0 0 0, 23, PR5, 5, AXPR5 TN3270E_6. : OFF, 0 0 0 0, 23, PR6, 6, AXPR6 TN3270E_7. : OFF, 0 0 0 0, 23, PR7, 7, AXPR7 TN3270E_8. : OFF, 0 0 0 0, 23, PR8, 8, AXPR8 --- TN5250E TN5250E_KA. : YES TN5250E_1.
PAGE 297
AXIS 5570e/AXIS 5670e User’s Manual RARP_ENB. : YES WINS_ENB. : YES Section 23: The Parameter List WINS_ADDR1. : 0 0 0 0 WINS_ADDR2. : 0 0 0 0 NBT_SCOPE_ID. : DNS_ENB. : YES DNS_ADDR1. : 0 0 0 0 DNS_ADDR2. : 0 0 0 0 DOMAIN_NAME. : SLP_ENB. : YES SLP_SCOPE_LIST. : DEFAULT SMTP_SERVER. : FTP_ENB. : YES TELNET_ENB. : YES DEFAULT_RAW_TCP. : 9100-9101 (9100-9101, CLOSED) RTN_OPT. : NO RTN_PR1. : 0, ASCII, 1 RTN_PR2. : 0, ASCII, 2 RTN_PR3. : 0, ASCII, 3 RTN_PR4. : 5011, SCS, 4 RTN_PR5.
PAGE 298
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual SYS_NAME. : SNMP_AUT. : DISABLE (DISABLE, ENABLE) TRAP_PRT. : DISABLE (DISABLE, ENABLE) --- NetWare Menu NETW_ENB. : YES NETW_TRANSPORT_PROTOCOL. : DUAL_STACK (IPX_ONLY, IP_ONLY, DUAL_STACK) NDPS. : TCP_AND_SPX (TCP_AND_SPX, TCP_ONLY, SPX_ONLY, DISABLED) JOB_CHECK_DELAY. : 5 CONF_CHECK_DELAY. : 300 FR_802_3. : YES FR_ETH_2. : YES FR_802_2. : YES FR_SNAP. : YES NCP_BURST_MODE. : YES PSERVER_NDS_TREE.
PAGE 299
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PSERVER_BINDERY16. : NPRINTER1. : NPRINTER2. : NPRINTER3. : NPRINTER4. : NPRINTER5. : NPRINTER6. : NPRINTER7. : NPRINTER8. : --- NetBIOS/NetBEUI Menu LSLM_ENB. : YES NB_FR_TYPE. : FR_802_2 (FR_AUTO, FR_802_2, FR_DIX) LPRINT_1. : AX181E6A.LP1 LLOGIC_1. : PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1) LPRINT_2. : AX181E6A.US1 LLOGIC_2. : PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1) LPRINT_3. : LLOGIC_3.
PAGE 300
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual --- AppleTalk Menu ATLK_ENB. : YES ATK_ZONE. : ZONER_EN. : YES ATK_FONT. : DEFAULT (DEFAULT, 35N, ALL) AUTO_DT_PRIN. : NO APRINT_1. : AXIS181E6A_LPT1 ATYPE_1. : LaserWriter ALOGIC_1. : PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1) BINARY_TYPE_1. : TBCP (TBCP, BCP, NONE) APRINT_2. : AXIS181E6A_USB1 ATYPE_2. : LaserWriter ALOGIC_2. : PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1) BINARY_TYPE_2.
PAGE 301
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List --- Printer2 Menu PR2_OUT. : USB1 (NONE, LPT1, USB1) PR2_NAME. : PR2_SCND. : PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR2_WAIT. : YES PR2_IN. : AUTO (AUTO, NONE) PR2_BEF. : PR2_STR. : PR2_CSET. DEC>IBM) : NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM, PR2_FILT. : NONE (NONE, POSTSCR, AUTO_PS) PR2_AFT. : PR2_DUMP. PR2_SIZE. : NO : A4 (A4, LETTER, LEGAL, EXECUT) PR2_ORNT.
PAGE 302
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual PR3_FONT. : --- Printer4 Menu PR4_OUT. : USB1 (NONE, LPT1, USB1) PR4_NAME. : PR4_SCND. : PR4 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR4_WAIT. : YES PR4_IN. : AUTO (AUTO, NONE) PR4_BEF. : PR4_STR. : PR4_CSET. DEC>IBM) : NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM, PR4_FILT. : NONE (NONE, POSTSCR, AUTO_PS) PR4_AFT. : PR4_DUMP. PR4_SIZE. : NO : A4 (A4, LETTER, LEGAL, EXECUT) PR4_ORNT.
PAGE 303
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PR5_ORNT. : PORTR (PORTR, LANDS, R_PORTR, R_LANDS) PR5_FORM. : 66 0 100 60 30 50 PR5_FONT. : --- Printer6 Menu PR6_OUT. : USB1 (NONE, LPT1, USB1) PR6_NAME. : PR6_SCND. : PR6 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR6_WAIT. : YES PR6_IN. : AUTO (AUTO, NONE) PR6_BEF. : PR6_STR. : PR6_CSET. DEC>IBM) : NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM, PR6_FILT. : NONE (NONE, POSTSCR, AUTO_PS) PR6_AFT.
PAGE 304
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual PR7_DUMP. PR7_SIZE. : NO : A4 (A4, LETTER, LEGAL, EXECUT) PR7_ORNT. : PORTR (PORTR, LANDS, R_PORTR, R_LANDS) PR7_FORM. : 66 0 100 60 30 50 PR7_FONT. : --- Printer8 Menu PR8_OUT. : USB1 (NONE, LPT1, USB1) PR8_NAME. : PR8_SCND. : PR8 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR8_WAIT. : YES PR8_IN. : AUTO (AUTO, NONE) PR8_BEF. : PR8_STR. : PR8_CSET.
PAGE 305
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List U1_COMMENT. : U1_BIDIR. : AUTO (DISABLE, AUTO) U1_READT. :3 --- IBM EMULATOR 1 PREMUL1. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX, 5X27_005_TX) SYSL1.
PAGE 306
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual LPI2. : 6 (3, 4, 6, 8) CPI2. : 10 (5, 10, 12, 13.3, 15, 17, 18) DCPI2. : 5.0 (5.0, 6.0, 6.7, 7.5, 9.0) AUTORI2. : YES LM2. : 0, 0, 48 TM2. : 26, 26, 74 LDSF2. : 100, 100, 70 DEFBIN2. : BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS) PRDRIVER2. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS) --- IBM EMULATOR 3 PREMUL3.
PAGE 307
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List --- IBM EMULATOR 4 PREMUL4. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX, 5X27_005_TX) SYSL4.
PAGE 308
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual LM5. : 0, 0, 48 TM5. : 26, 26, 74 LDSF5. : 100, 100, 70 DEFBIN5. : BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS) PRDRIVER5. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS) --- IBM EMULATOR 6 PREMUL6.
PAGE 309
AXIS 5570e/AXIS 5670e User’s Manual PASSTHR7. : NO MPL7. : 66, ENA MPP7. : 132, ENA LPI7. : 6 (3, 4, 6, 8) CPI7. : 10 (5, 10, 12, 13.3, 15, 17, 18) DCPI7. Section 23: The Parameter List : 5.0 (5.0, 6.0, 6.7, 7.5, 9.0) AUTORI7. : YES LM7. : 0, 0, 48 TM7. : 26, 26, 74 LDSF7. : 100, 100, 70 DEFBIN7. : BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS) PRDRIVER7.
PAGE 310
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual --- IBM SCS PAGE FORMAT PCORI. : NO DWSISO. : NO BIN1. : COR, LETTER, 0, 0 BIN2. : COR, LETTER, 0, 0 BIN3. : COR, LETTER, 0, 0 BIN4. : COR, LETTER, 0, 0 BIN5. : COR, LETTER, 0, 0 BIN6. : COR, LETTER, 0, 0 MANUAL. : COR, LETTER, 0, 0 ENVELOPE. : COR, LETTER, 0, 0 CONTINUOUS. : COR, LETTER, 0, 0 SIMBF. : YES --- IBM SCS CPI MAPPING FGID_CPI5. : 244, 11 FGID_CPI10. : 11, 204 FGID_CPI12. : 86, 230 FGID_CPI15.
PAGE 311
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List --- IBM 3270 OPTIONS CASE. : DUAL (DUAL, MONO) BASCOL. : BLACK, ENA XSTRN. :0 AUTNL. :1 ADDNL. :1 FFWPB. :0 FFEOPB. :1 NULSUP. :0 FFCPOS. :0 AFEOPB. :0 --- IBM SCS EXTENDED EMULATION XEMUL. : YES WARN. : NO SSUBST. : YES SBTS. : TLIS. : 025 03C TTRS. : 03E 025 FLIS. : 025 02F EECS. COBXEM. CCLIS.
PAGE 312
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual --- SSTR -------- --- MSTR -------- --- IBM PRINTER DRIVER PRDRIVERBASE. : PCL5 (GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS) SOJS. : 1B 45 1B 26 6C 30 4C EOJS. : 1B 45 BACKSPS. : 08 CRS. : 0D LFS. : 0A NLS. : 0D 0A FFS. : 0C SOS. : SIS. BLKS. : : GRNS. : BLUS. : REDS. : MAGS. : CYNS. YELS. : : BIN1S. : 1B 26 6C 31 48 BIN2S. : 1B 26 6C 34 48 BIN3S.
PAGE 313
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List CSIZS. : LAC. : HP_PCL (DISABLE, HP_PCL, EPSON_LQ) GRD. : HP_PCL (DISABLE, HP_PCL, EPSON_LQ) JOGS. : 1B 26 6C 31 54 SSUS. : SBSET. : PC850 (ECMA94, LATIN9, PC437, PC850, PC852, PC857, PC858, PC874, PC891, PC903, PC904, PC942, ROMAN8, USASCII, USER) --- FONT FGID CSSF SBSET SPACING PITCH HEIGHT STYLE STROKE TYPEFACE STRING ---------------------------------------------------------------------------------FONT.
PAGE 314
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual FONT. : 84, 98, DEFAULT,FIXED, 120, 0, UPRIGHT,MEDIUM,4099, FONT. : 85, 98, DEFAULT,FIXED, 120, 0, UPRIGHT,MEDIUM,4099, FONT. : 86, 98, DEFAULT,FIXED, 120, 0, UPRIGHT,MEDIUM,4099, FONT. : 87, 98, DEFAULT,FIXED, 130, 0, UPRIGHT,MEDIUM,4102, FONT. : 91, 98, DEFAULT,FIXED, 120, 0, ITALIC,MEDIUM,4099, FONT. : 108, 98, DEFAULT,FIXED, 120, 0, UPRIGHT,BOLD, 4099, FONT.
PAGE 315
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 751, 100, DEFAULT,PROP, 0, 80, FONT. : 1051, 100, DEFAULT,PROP, 0, 100, UPRIGHT,MEDIUM,4101, FONT. : 1053, 100, DEFAULT,PROP, 0, 100, UPRIGHT,BOLD, 4101, FONT. : 1056, 100, DEFAULT,PROP, 0, 100, ITALIC,MEDIUM,4101, FONT. : 1351, 100, DEFAULT,PROP, 0, 120, UPRIGHT,MEDIUM,4101, FONT. : 1653, 100, DEFAULT,PROP, 0, 160, UPRIGHT,BOLD, 4101, FONT. : 2103, 100, DEFAULT,PROP, 0, 240, UPRIGHT,BOLD, 4101, FONT.
PAGE 316
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual FONT. : 3861, 100, DEFAULT,PROP, 0, 0, UPRIGHT,MEDIUM,4197, FONT. : 3862, 100, DEFAULT,PROP, 0, 0, UPRIGHT,BOLD, 4197, FONT. : 3863, 100, DEFAULT,PROP, 0, 0, ITALIC,MEDIUM,4197, FONT. : 3864, 100, DEFAULT,PROP, 0, 0, ITALIC,BOLD, 4197, FONT. : 3865, 100, DEFAULT,PROP, 0, 0, UPRIGHT,MEDIUM,4297, FONT. : 3866, 100, DEFAULT,PROP, 0, 0, UPRIGHT,NONE, 4362, 1B 28 73 31 42 FONT.
PAGE 317
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 33591,100, DEFAULT,PROP, 0, 0, UPRIGHT,MEDIUM,16602, FONT. : 33601,100, DEFAULT,PROP, 0, 0, UPRIGHT,BOLD, 16602, FONT. : 33719,100, DEFAULT,PROP, 0, 0, ITALIC,MEDIUM,16602, FONT. : 33729,100, DEFAULT,PROP, 0, 0, ITALIC,BOLD, 16602, FONT. : 34103,100, DEFAULT,PROP, 0, 0, UPRIGHT,MEDIUM,4148, FONT. : 34123,100, DEFAULT,PROP, 0, 0, UPRIGHT,BOLD, 4148, FONT.
PAGE 318
Section 23: The Parameter List FONT. AXIS 5570e/AXIS 5670e User’s Manual : 50010,100, PC942,PROP, 0, 76, UPRIGHT,MEDIUM,28752, 1B 67, UPRIGHT,MEDIUM,28752, 1B 67, UPRIGHT,MEDIUM,28752, 1B 56, UPRIGHT,MEDIUM,28752, 1B 28 31 39 4B 1B 26 74 33 31 50 FONT. : 50011,100, PC942,PROP, 0, 28 31 39 4B 1B 26 74 33 31 50 FONT. : 50012,100, PC942,PROP, 0, 28 31 39 4B 1B 26 74 33 31 50 FONT. : 50013,100, PC942,PROP, 0, 28 31 39 4B 1B 26 74 33 31 50 FONT.
PAGE 319
AXIS 5570e/AXIS 5670e User’s Manual FONT. : 50032,100, PC891,PROP, 0, Section 23: The Parameter List 120, UPRIGHT,MEDIUM,43088, 1B 28 31 39 48 1B 26 74 33 38 50 FONT. : 50033,100, PC891,PROP, 0, 108, UPRIGHT,MEDIUM,43088, 1B 28 31 39 48 1B 26 74 33 38 50 FONT. : 50034,100, PC891,PROP, 0, 96, UPRIGHT,MEDIUM,43088, 1B 96, UPRIGHT,MEDIUM,43088, 1B 80, UPRIGHT,MEDIUM,43088, 1B 28 31 39 48 1B 26 74 33 38 50 FONT. : 50035,100, PC891,PROP, 0, 28 31 39 48 1B 26 74 33 38 50 FONT.
PAGE 320
Section 23: The Parameter List FONT. AXIS 5570e/AXIS 5670e User’s Manual : 50048,100, PC891,PROP, 0, 80, UPRIGHT,MEDIUM,41040, 1B 28 31 39 48 1B 26 74 33 38 50 FONT. : 50049,100, PC891,PROP, 0, 101, UPRIGHT,MEDIUM,41040, 1B 28 31 39 48 1B 26 74 33 38 50 FONT. : 50050,100, PC891,PROP, 0, 84, UPRIGHT,MEDIUM,41040, 1B 76, UPRIGHT,MEDIUM,41040, 1B 67, UPRIGHT,MEDIUM,41040, 1B 56, UPRIGHT,MEDIUM,41040, 1B 28 31 39 48 1B 26 74 33 38 50 FONT.
PAGE 321
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 50081,100, PC904,PROP, 0, 76, UPRIGHT,MEDIUM,0, FONT. : 50082,100, PC904,PROP, 0, 67, UPRIGHT,MEDIUM,0, FONT. : 50083,100, PC904,PROP, 0, 56, UPRIGHT,MEDIUM,0, FONT. : 50100,100, PC903,PROP, 0, 144, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT. : 50101,100, PC903,PROP, 0, 144, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT.
PAGE 322
Section 23: The Parameter List FONT. AXIS 5570e/AXIS 5670e User’s Manual : 50115,100, PC903,PROP, 0, 120, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT. : 50116,100, PC903,PROP, 0, 108, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT. : 50117,100, PC903,PROP, 0, 96, UPRIGHT,MEDIUM,37058, 1B 80, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT. : 50118,100, PC903,PROP, 0, 28 31 38 43 1B 26 74 33 38 50 FONT.
PAGE 323
AXIS 5570e/AXIS 5670e User’s Manual FONT. : 50137,100, PC891,PROP, 0, Section 23: The Parameter List 101, UPRIGHT,MEDIUM,43088, 1B 28 31 38 48 1B 26 74 33 38 50 FONT. : 50138,100, PC891,PROP, 0, 101, UPRIGHT,MEDIUM,43088, 1B 28 31 38 48 1B 26 74 33 38 50 FONT. : 50139,100, PC891,PROP, 0, 84, UPRIGHT,MEDIUM,43088, 1B 76, UPRIGHT,MEDIUM,43088, 1B 67, UPRIGHT,MEDIUM,43088, 1B 67, UPRIGHT,MEDIUM,43088, 1B 56, UPRIGHT,MEDIUM,43088, 1B 28 31 38 48 1B 26 74 33 38 50 FONT.
PAGE 324
Section 23: The Parameter List FONT. AXIS 5570e/AXIS 5670e User’s Manual : 50153,100, PC891,PROP, 0, 56, UPRIGHT,MEDIUM,41040, 1B 28 31 38 48 1B 26 74 33 38 50 --- Email Menu EMAIL_NOTIFICATION. : YES REPLY_ADDRESS. : PAPER_JAM_ADDRESS. : OUT_OF_PAPER_ADDRESS. : TONER_LOW_ADDRESS. : NO_TONER_ADDRESS. : PRINTER_OFFLINE_ADDRESS. : AXIS 5670e: --- General Menu NODE_ADDR. : 00 40 8C XX XX XX NETWORK_SPEED. : AUTO_SENSE (AUTO_SENSE, 10_HALF_DX, 10_FULL_DX, 100_HALF_DX, 100_FULL_DX) PS_NAME.
PAGE 325
AXIS 5570e/AXIS 5670e User’s Manual NODE_ID. Section 23: The Parameter List : E0 78 1E 58 NODE_SAP. : $4 NWORK_NAME. : APPN LU_NAME. H1_SAP. : A85E181C : $4 H1_ADDR. : FF FF FF FF FF FF H1_NW_NAME. : APPN H1_MOD_NAME. : QRMTWSC H1_LU_NAME. : DEFAULT SNA_LU1. : NONE, 1 SNA_LU2. : NONE, 2 SNA_LU3. : NONE, 3 SNA_LU4. : NONE, 4 SNA_LU5. : NONE, 5 SNA_LU6. : NONE, 6 SNA_LU7. : NONE, 7 SNA_LU8. : NONE, 8 AUTODIAL. : NO DIALTIME. : 20 JOB_TIME. : 10 IR_TIME. :0 SNA_HEXDUMP.
PAGE 326
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual TN3270E_8. : OFF, 0 0 0 0, 23, PR8, 8, AXPR8 --- TN5250E TN5250E_KA. : YES TN5250E_1. : OFF, 0 0 0 0, 23, PR1, 1, AXPR1, QSYSOPR, QSYS TN5250E_2. : OFF, 0 0 0 0, 23, PR2, 2, AXPR2, QSYSOPR, QSYS TN5250E_3. : OFF, 0 0 0 0, 23, PR3, 3, AXPR3, QSYSOPR, QSYS TN5250E_4. : OFF, 0 0 0 0, 23, PR4, 4, AXPR4, QSYSOPR, QSYS TN5250E_5. : OFF, 0 0 0 0, 23, PR5, 5, AXPR5, QSYSOPR, QSYS TN5250E_6.
PAGE 327
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List DOMAIN_NAME. : SLP_ENB. : YES SLP_SCOPE_LIST. : DEFAULT SMTP_SERVER. : FTP_ENB. : YES TELNET_ENB. : YES DEFAULT_RAW_TCP. : 9100-9102 (9100-9102, CLOSED) RTN_OPT. : NO PPR_PRSTAT. : NO RTN_PR1. : 5001, IPDS, 1 RTN_PR2. : 0, ASCII, 2 RTN_PR3. : 0, ASCII, 3 RTN_PR4. : 5011, SCS, 4 RTN_PR5. : 5012, SCS, 5 RTN_PR6. : 5013, SCS, 6 RTN_PR7. : 0, ASCII, 7 RTN_PR8. : 0, ASCII, 8 DEF_IP_FRAME_TYPE.
PAGE 328
Section 23: The Parameter List NDPS. AXIS 5570e/AXIS 5670e User’s Manual : TCP_AND_SPX (TCP_AND_SPX, TCP_ONLY, SPX_ONLY, DISABLED) JOB_CHECK_DELAY. : 5 CONF_CHECK_DELAY. : 300 FR_802_3. : YES FR_ETH_2. : YES FR_802_2. : YES FR_SNAP. : YES NCP_BURST_MODE. : YES PSERVER_NDS_TREE. : PSERVER_NDS_FILESERVER. : PSERVER_NDS_DISTINGUISHED_NAME. : PSERVER_BINDERY1. : PSERVER_BINDERY2. : PSERVER_BINDERY3. : PSERVER_BINDERY4. : PSERVER_BINDERY5. : PSERVER_BINDERY6. : PSERVER_BINDERY7.
PAGE 329
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List NPRINTER7. : NPRINTER8. : --- NetBIOS/NetBEUI Menu LSLM_ENB. : YES NB_FR_TYPE. : FR_802_2 (FR_AUTO, FR_802_2, FR_DIX) LPRINT_1. : AX181E58.LP1 LLOGIC_1. : PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2) LPRINT_2. : AX181E58.LP2 LLOGIC_2. : PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2) LPRINT_3. : AX181E58.CM1 LLOGIC_3. : PR3 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2) LPRINT_4.
PAGE 330
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual APRINT_2. : AXIS181E58_LPT2 ATYPE_2. : LaserWriter ALOGIC_2. : PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2) BINARY_TYPE_2. : TBCP (TBCP, BCP, NONE) APRINT_3. : AXIS181E58_COM1 ATYPE_3. : LaserWriter ALOGIC_3. : PR3 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2) BINARY_TYPE_3. : TBCP (TBCP, BCP, NONE) --- Printer1 Menu PR1_OUT. : LPT1 (NONE, LPT1, COM1, LPT2) PR1_NAME. : PR1_SCND.
PAGE 331
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PR1_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL, TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT, TOP_DOUBLE, LEFT_DOUBLE, CENTER) PR1_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE) PR1_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD) PR1_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5) PR1_DC_COP. : 1 --- Printer2 Menu PR2_OUT. : LPT2 (NONE, LPT1, COM1, LPT2) PR2_NAME. : PR2_SCND.
PAGE 332
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual PR2_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE) PR2_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD) PR2_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5) PR2_DC_COP. : 1 --- Printer3 Menu PR3_OUT. : COM1 (NONE, LPT1, COM1, LPT2) PR3_NAME. : PR3_SCND. : PR3 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR3_WAIT. : YES PR3_IN. : AUTO (AUTO, NONE, COM1) PR3_BEF. : PR3_STR. : PR3_CSET.
PAGE 333
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PR3_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5) PR3_DC_COP. : 1 --- Printer4 Menu PR4_OUT. : COM1 (NONE, LPT1, COM1, LPT2) PR4_NAME. : PR4_SCND. : PR4 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR4_WAIT. : YES PR4_IN. : AUTO (AUTO, NONE, COM1) PR4_BEF. : PR4_STR. : PR4_CSET. DEC>IBM) : NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM, PR4_FILT. : NONE (NONE, POSTSCR, AUTO_PS) PR4_AFT. : PR4_DUMP.
PAGE 334
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual --- Printer5 Menu PR5_OUT. : LPT1 (NONE, LPT1, COM1, LPT2) PR5_NAME. : PR5_SCND. : PR5 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR5_WAIT. : YES PR5_IN. : AUTO (AUTO, NONE, COM1) PR5_BEF. : PR5_STR. : PR5_CSET. DEC>IBM) : NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM, PR5_FILT. : NONE (NONE, POSTSCR, AUTO_PS) PR5_AFT. : PR5_DUMP. PR5_SIZE. : NO : A4 (A4, LETTER, LEGAL, EXECUT) PR5_ORNT.
PAGE 335
AXIS 5570e/AXIS 5670e User’s Manual PR6_OUT. Section 23: The Parameter List : LPT2 (NONE, LPT1, COM1, LPT2) PR6_NAME. : PR6_SCND. : PR6 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR6_WAIT. : YES PR6_IN. : AUTO (AUTO, NONE, COM1) PR6_BEF. : PR6_STR. : PR6_CSET. DEC>IBM) : NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM, PR6_FILT. : NONE (NONE, POSTSCR, AUTO_PS) PR6_AFT. : PR6_DUMP. PR6_SIZE. : NO : A4 (A4, LETTER, LEGAL, EXECUT) PR6_ORNT.
PAGE 336
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual PR7_SCND. : PR7 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR7_WAIT. : YES PR7_IN. : AUTO (AUTO, NONE, COM1) PR7_BEF. : PR7_STR. : PR7_CSET. DEC>IBM) : NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM, PR7_FILT. : NONE (NONE, POSTSCR, AUTO_PS) PR7_AFT. : PR7_DUMP. PR7_SIZE. : NO : A4 (A4, LETTER, LEGAL, EXECUT) PR7_ORNT. : PORTR (PORTR, LANDS, R_PORTR, R_LANDS) PR7_FORM.
PAGE 337
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PR8_IN. : AUTO (AUTO, NONE, COM1) PR8_BEF. : PR8_STR. : PR8_CSET. DEC>IBM) : NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM, PR8_FILT. : NONE (NONE, POSTSCR, AUTO_PS) PR8_AFT. : PR8_DUMP. PR8_SIZE. : NO : A4 (A4, LETTER, LEGAL, EXECUT) PR8_ORNT. : PORTR (PORTR, LANDS, R_PORTR, R_LANDS) PR8_FORM. : 66 0 100 60 30 50 PR8_FONT. : PR8_DC_MOD.
PAGE 338
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual --- COM1 Menu C1_BAUDR. : 9600 (300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200) C1_NBITS. : 8 (7, 8) C1_PARIT. : NONE (NONE, ODD, EVEN) C1_STOPB. : 2 (1, 2) C1_HNDSH. : ROBUST-BOTH (NONE, XON/XOFF, ROBUST, RDY/BSY, BOTH, ROBUST-BOTH) C1_READT. :3 C1_BSYTM. : 60 C1_MGM_INFO. : AUTO (DISABLE, AUTO) C1_COMMENT. : --- LPT2 Menu L2_CENTR. : HISPEED (IBM_PC, STNDRD, FAST, HISPEED, HINOACK) L2_BSYTM.
PAGE 339
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List IPDS_BIN1. : Letter, 0, 0 IPDS_BIN2. : Letter, 0, 0 IPDS_BIN3. : Letter, 0, 0 IPDS_BIN4. : Letter, 0, 0 IPDS_BIN5. : Letter, 0, 0 --- IBM IPDS PostScript Driver Settings PS_LFSM. : Enabled PS_ERRH. : Disabled PS_OPTOVL. : Enabled PS_G4SUP. : Disabled PS_VM. : 2000 PS_BIN1. : Default, 100, 100, 0, 0 PS_BIN2. : Default, 100, 100, 0, 0 PS_BIN3. : Default, 100, 100, 0, 0 PS_BIN4. : Default, 100, 100, 0, 0 PS_BIN5.
PAGE 340
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual IPDS_PREMUL1. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3, IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1, IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332) IPDS_PRRES1. : 0 IPDS_SYSL1.
PAGE 341
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List IPDS_SYSL2. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361, 420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860, 861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923, 924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, 1252) IPDS_PD2. : PostScript (PostScript, PCL) IPDS_SOJS2. : IPDS_EOJS2. : PREMUL2.
PAGE 342
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual IPDS_SOJS3. : IPDS_EOJS3. : PREMUL3. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX, 5X27_005_TX) SYSL3.
PAGE 343
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PREMUL4. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX, 5X27_005_TX) SYSL4.
PAGE 344
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual SYSL5. : 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, USER) PASSTHR5. : NO MPL5. : 66, ENA MPP5. : 132, ENA LPI5. : 6 (3, 4, 6, 8) CPI5. : 10 (5, 10, 12, 13.3, 15, 17, 18) DCPI5. : 5.0 (5.0, 6.0, 6.7, 7.5, 9.0) AUTORI5. : YES LM5. : 0, 0, 48 TM5.
PAGE 345
AXIS 5570e/AXIS 5670e User’s Manual MPP6. Section 23: The Parameter List : 132, ENA LPI6. : 6 (3, 4, 6, 8) CPI6. : 10 (5, 10, 12, 13.3, 15, 17, 18) DCPI6. : 5.0 (5.0, 6.0, 6.7, 7.5, 9.0) AUTORI6. : YES LM6. : 0, 0, 48 TM6. : 26, 26, 74 LDSF6. : 100, 100, 70 DEFBIN6. : BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS) PRDRIVER6.
PAGE 346
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual AUTORI7. : YES LM7. : 0, 0, 48 TM7. : 26, 26, 74 LDSF7. : 100, 100, 70 DEFBIN7. : BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS) PRDRIVER7. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS) --- IBM EMULATOR 8 IPDS_PREMUL8.
PAGE 347
AXIS 5570e/AXIS 5670e User’s Manual DEFBIN8. Section 23: The Parameter List : BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS) PRDRIVER8. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS) --- IBM SCS PAGE FORMAT PCORI. : NO DWSISO. : NO BIN1. : COR, LETTER, 0, 0 BIN2. : COR, LETTER, 0, 0 BIN3. : COR, LETTER, 0, 0 BIN4. : COR, LETTER, 0, 0 BIN5. : COR, LETTER, 0, 0 BIN6. : COR, LETTER, 0, 0 MANUAL.
PAGE 348
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual SUPFFBLANK. : NO --- IBM 3270 OPTIONS CASE. : DUAL (DUAL, MONO) BASCOL. : BLACK, ENA XSTRN. :0 AUTNL. :1 ADDNL. :1 FFWPB. :0 FFEOPB. :1 NULSUP. :0 FFCPOS. :0 AFEOPB. :0 --- IBM SCS EXTENDED EMULATION XEMUL. : YES WARN. : NO SSUBST. : YES SBTS. TLIS. : : 025 03C TTRS. : 03E 025 FLIS. : 025 02F EECS. COBXEM. CCLIS.
PAGE 349
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List -------- --- MSTR -------- --- IBM PRINTER DRIVER PRDRIVERBASE. : PCL5 (GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS) SOJS. : 1B 45 1B 26 6C 30 4C EOJS. : 1B 45 BACKSPS. : 08 CRS. : 0D LFS. : 0A NLS. : 0D 0A FFS. : 0C SOS. SIS. BLKS. : : : GRNS. : BLUS. : REDS. : MAGS. : CYNS. YELS. : : BIN1S. : 1B 26 6C 31 48 BIN2S. : 1B 26 6C 34 48 BIN3S.
PAGE 350
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual LAC. : HP_PCL (DISABLE, HP_PCL, EPSON_LQ) GRD. : HP_PCL (DISABLE, HP_PCL, EPSON_LQ) JOGS. : 1B 26 6C 31 54 SSUS. : SBSET. : PC850 (ECMA94, LATIN9, PC437, PC850, PC852, PC857, PC858, PC874, PC891, PC903, PC904, PC942, ROMAN8, USASCII, USER) --- FONT FGID CSSF SBSET SPACING PITCH HEIGHT STYLE STROKE TYPEFACE STRING ---------------------------------------------------------------------------------FONT.
PAGE 351
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 85, 98, DEFAULT,FIXED, 120, 0, UPRIGHT,MEDIUM,4099, FONT. : 86, 98, DEFAULT,FIXED, 120, 0, UPRIGHT,MEDIUM,4099, FONT. : 87, 98, DEFAULT,FIXED, 130, 0, UPRIGHT,MEDIUM,4102, FONT. : 91, 98, DEFAULT,FIXED, 120, 0, ITALIC,MEDIUM,4099, FONT. : 108, 98, DEFAULT,FIXED, 120, 0, UPRIGHT,BOLD, 4099, FONT. : 110, 98, DEFAULT,FIXED, 130, 0, UPRIGHT,BOLD, 4102, FONT.
PAGE 352
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual FONT. : 1051, 100, DEFAULT,PROP, 0, 100, UPRIGHT,MEDIUM,4101, FONT. : 1053, 100, DEFAULT,PROP, 0, 100, UPRIGHT,BOLD, 4101, FONT. : 1056, 100, DEFAULT,PROP, 0, 100, ITALIC,MEDIUM,4101, FONT. : 1351, 100, DEFAULT,PROP, 0, 120, UPRIGHT,MEDIUM,4101, FONT. : 1653, 100, DEFAULT,PROP, 0, 160, UPRIGHT,BOLD, 4101, FONT. : 2103, 100, DEFAULT,PROP, 0, 240, UPRIGHT,BOLD, 4101, FONT.
PAGE 353
AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 3862, 100, DEFAULT,PROP, 0, 0, UPRIGHT,BOLD, 4197, FONT. : 3863, 100, DEFAULT,PROP, 0, 0, ITALIC,MEDIUM,4197, FONT. : 3864, 100, DEFAULT,PROP, 0, 0, ITALIC,BOLD, 4197, FONT. : 3865, 100, DEFAULT,PROP, 0, 0, UPRIGHT,MEDIUM,4297, FONT. : 3866, 100, DEFAULT,PROP, 0, 0, UPRIGHT,NONE, 4362, 1B 28 73 31 42 FONT. : 3867, 100, DEFAULT,PROP, 0, 0, UPRIGHT,NONE, 4362, 1B 28 73 34 42 FONT.
PAGE 354
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual FONT. : 33601,100, DEFAULT,PROP, 0, 0, UPRIGHT,BOLD, 16602, FONT. : 33719,100, DEFAULT,PROP, 0, 0, ITALIC,MEDIUM,16602, FONT. : 33729,100, DEFAULT,PROP, 0, 0, ITALIC,BOLD, 16602, FONT. : 34103,100, DEFAULT,PROP, 0, 0, UPRIGHT,MEDIUM,4148, FONT. : 34123,100, DEFAULT,PROP, 0, 0, UPRIGHT,BOLD, 4148, FONT. : 34231,100, DEFAULT,PROP, 0, 0, ITALIC,MEDIUM,4148, FONT.
PAGE 355
AXIS 5570e/AXIS 5670e User’s Manual FONT. : 50011,100, PC942,PROP, 0, Section 23: The Parameter List 67, UPRIGHT,MEDIUM,28752, 1B 67, UPRIGHT,MEDIUM,28752, 1B 56, UPRIGHT,MEDIUM,28752, 1B 28 31 39 4B 1B 26 74 33 31 50 FONT. : 50012,100, PC942,PROP, 0, 28 31 39 4B 1B 26 74 33 31 50 FONT. : 50013,100, PC942,PROP, 0, 28 31 39 4B 1B 26 74 33 31 50 FONT. : 50014,100, PC942,PROP, 0, 144, UPRIGHT,MEDIUM,28752, 1B 28 31 39 4B 1B 26 74 33 31 50 FONT.
PAGE 356
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual 28 31 39 48 1B 26 74 33 38 50 FONT. : 50034,100, PC891,PROP, 0, 96, UPRIGHT,MEDIUM,43088, 1B 96, UPRIGHT,MEDIUM,43088, 1B 80, UPRIGHT,MEDIUM,43088, 1B 28 31 39 48 1B 26 74 33 38 50 FONT. : 50035,100, PC891,PROP, 0, 28 31 39 48 1B 26 74 33 38 50 FONT. : 50036,100, PC891,PROP, 0, 28 31 39 48 1B 26 74 33 38 50 FONT. : 50037,100, PC891,PROP, 0, 101, UPRIGHT,MEDIUM,43088, 1B 28 31 39 48 1B 26 74 33 38 50 FONT.
PAGE 357
AXIS 5570e/AXIS 5670e User’s Manual FONT. : 50050,100, PC891,PROP, 0, Section 23: The Parameter List 84, UPRIGHT,MEDIUM,41040, 1B 76, UPRIGHT,MEDIUM,41040, 1B 67, UPRIGHT,MEDIUM,41040, 1B 56, UPRIGHT,MEDIUM,41040, 1B 28 31 39 48 1B 26 74 33 38 50 FONT. : 50051,100, PC891,PROP, 0, 28 31 39 48 1B 26 74 33 38 50 FONT. : 50052,100, PC891,PROP, 0, 28 31 39 48 1B 26 74 33 38 50 FONT. : 50053,100, PC891,PROP, 0, 28 31 39 48 1B 26 74 33 38 50 FONT.
PAGE 358
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual 28 31 38 43 1B 26 74 33 38 50 FONT. : 50101,100, PC903,PROP, 0, 144, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT. : 50102,100, PC903,PROP, 0, 120, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT. : 50103,100, PC903,PROP, 0, 108, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT.
PAGE 359
AXIS 5570e/AXIS 5670e User’s Manual FONT. : 50117,100, PC903,PROP, 0, Section 23: The Parameter List 96, UPRIGHT,MEDIUM,37058, 1B 80, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT. : 50118,100, PC903,PROP, 0, 28 31 38 43 1B 26 74 33 38 50 FONT. : 50119,100, PC903,PROP, 0, 101, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT.
PAGE 360
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual 28 31 38 48 1B 26 74 33 38 50 FONT. : 50140,100, PC891,PROP, 0, 76, UPRIGHT,MEDIUM,43088, 1B 67, UPRIGHT,MEDIUM,43088, 1B 67, UPRIGHT,MEDIUM,43088, 1B 56, UPRIGHT,MEDIUM,43088, 1B 28 31 38 48 1B 26 74 33 38 50 FONT. : 50141,100, PC891,PROP, 0, 28 31 38 48 1B 26 74 33 38 50 FONT. : 50142,100, PC891,PROP, 0, 28 31 38 48 1B 26 74 33 38 50 FONT. : 50143,100, PC891,PROP, 0, 28 31 38 48 1B 26 74 33 38 50 FONT.
PAGE 361
AXIS 5570e/AXIS 5670e User’s Manual PAPER_JAM_ADDRESS. : OUT_OF_PAPER_ADDRESS. : TONER_LOW_ADDRESS. : NO_TONER_ADDRESS. : PRINTER_OFFLINE_ADDRESS.
PAGE 362
Section 24: Glossary Section 24 AXIS 5570e/AXIS 5670e User’s Manual Glossary Active Directory Active Directory - a structure supported by Windows 2000 that lets any object on a network be tracked and located. Active Directory is the directory service used in Windows 2000 Server and provides the foundation for Windows 2000 distributed networks. 3270DS 3270 Data Stream is a control language used for the 3270 family of terminals and controllers. Also used for printing.
PAGE 363
AXIS 5570e/AXIS 5670e User’s Manual Section 24: Glossary BSD Berkeley Software Distribution. The University of California, Berkeley additions to the UNIX operating system. config file This is a file that resides in the print server’s memory and contains all the parameters that determine the AXIS 5570e/AXIS 5670e functionality. By editing the config file (changing the parameter settings), you can configure the AXIS 5570e/AXIS 5670e to meet the printing needs of your network.
PAGE 364
Section 24: Glossary Flash Memory FTP AXIS 5570e/AXIS 5670e User’s Manual The print server software is stored in Flash Memory. This memory is provided by a silicon chip that like any other ROM device, retains data content even after power is removed. However, Flash Memory is unique because it allows its data to be erased and re-written. This means that you can install software updates for your server as soon as they become available, without having to replace any parts.
PAGE 365
AXIS 5570e/AXIS 5670e User’s Manual Section 24: Glossary Logical Printer A logical printer acts as a filter between the network and the physical printer. It appears to the user as a normal printer with additional characteristics. For example a UNIX workstation may only send a line feed (LF) to a shared printer that needs carriage return (CR) and LF. The logical printer can solve this problem by adding a CR. LPD Line Printer Daemon protocol. A print server protocol widely used on the Internet.
PAGE 366
Section 24: Glossary AXIS 5570e/AXIS 5670e User’s Manual NCP(2) Network Control Program. SNA program resident in the FEP. NCP offloads certain line protocol and routing functions from the host CPU. NDS PPR/PPD PU PU2.1 NetWare Directory Services. A hierarchical data base that manages NetWare network resources such as servers and volumes. Page Printer Requester/Page Printer Daemon. Bidirectional IBM proprietary TCP/IP application protocol.
PAGE 367
AXIS 5570e/AXIS 5670e User’s Manual Section 24: Glossary SCS SNA Character String. A sequence of control commands that allows sophisticated control of printers and other devices. SNA Systems Network Architecture. IBM's data communications architecture defining levels of protocols for communications between terminals and applications as well as between programs. Originally SNA was strictly host-based with VTAM controlling the network except for path control which was provided by NCP in the FEP.
PAGE 368
Section 24: Glossary AXIS 5570e/AXIS 5670e User’s Manual URL Uniform Resource Locator. A way of specifying the location of publicly available information on the Internet. VPDI Virtual Printer Driver Interface VTAM Virtual Telecommunications Access Method. Mainframe software that performs network control and management. VTAM's most important objective is to provide the SSCP services. WINS Windows Internet Name Service.
PAGE 369
AXIS 5570e/AXIS 5670e User’s Manual Index Numerics 3270DS 362 A Account file 194, 195 Active Directory 362 Admin 181 AIX 362 APPC 362 AppleTalk 159 Approvals 294 AS/400 35 ASCII 362 ASCII to Postscript Conversion 225 Autodetect 160 Auto-Detect Printer Type 162 AutoIP 25, 206 AutoIP address structure 25 Axinstall 173 AXIS IPP Gateway Configuration 143 AXIS LPR Gateway Configuration 143 AXIS MIB 200 AXIS Print Monitor 114 AXIS Product CD 18 AXIS ThinWizard Installing 189 B Backside label 17 Bar Codes 251 Bar
PAGE 370
AXIS 5570e/AXIS 5670e User’s Manual BSD 363 C Certificates 231 Delete 235 Import 234 View 235 Character Set Conversion 221 Checking SSL/TLS Status 235 Color 272 Concentrator gateway, general 248 Concentrator gateway, Microsoft 249 Concentrator gateway, NetWare 248 config file 180, 295, 363 Configuration and Management 18 Configuration methods FTP 192 NetWare Administrator 156, 201 PCONSOLE 156, 201 SNMP 199 Telnet 195 Web browser 182 Configuration Mode 251 Configuring AS/400 48 IBM Mainframes 61 Confi
PAGE 371
AXIS 5570e/AXIS 5670e User’s Manual Hex Dump Mode 229 Print Problems 229 Default Input Bin 273 Delete Certificate 235 Device Features 282 DEVICE Statement 93 DHCP Enabled parameter 25 Digital Copier printing 287 Digital Copier Support 286 Dimensions 293 Disabling Protocols 234 DNS 363 DSPU 247 Duplex 272 Dynamic IP address Assignment 25 E EBCDIC 363 Enable/disable SNMP 189 Enabling Protocols 234 Enabling SSL 231 Environmental 293 Ethernet Address 32 F Factory Default 188 Factory default settings 288 FEP 36
PAGE 372
AXIS 5570e/AXIS 5670e User’s Manual Selection 252 Typographical 278 Width 278 Front Panel 293 FSS Statement 89 FSSDEF Statement 92 FTP 192, 364 FTP_ENB 189 H Hardware 293 Hardware Inventory 14 Hex Dump Mode 229 Hex Transparancy 252 Host Name 33 HPR 364 HTML 364 HTTP 364 HTTPS 234 I IBM Capabilities 290 IBM Font Selection 255 IBM SNA 59 Importing a Certificate 234 Indicators 17, 18 Installation guide 22 Installation Summary 23 Installing AXIS ThinWizard 189 Internet Address 150 IP 364 IP Address Auto
PAGE 373
AXIS 5570e/AXIS 5670e User’s Manual IPP Client 209 Printing Requirements 208 iPrint 123 L Last Code Point 282 LLC 247 Local Printer 110 Logical Printer 365 Logical Printers 220, 291 Logon-mode Entry 63 LPD 177, 365 LPR 365 LU 365 LU6.
PAGE 374
AXIS 5570e/AXIS 5670e User’s Manual Remote Printer Mode 155 NetWare SAA 248 Network Indicator 17 Printer 110 Speed 230 Network Connection 292 Network Connector 17 Network Group Create 190 Network Indicator 17 P Paper Size Physical 273 Parameter List 187, 295 Pass-through gateway 247 password 182 Point size 278 Ports 17 Power Indicator 18 Power Consumption 293 PPR/PPD 366 Print Jobs Redirect 227 Print Problems Debugging 229 Print Server Management 292 Printer Autodetect 160 Ports 17 Printer Connection
PAGE 375
AXIS 5570e/AXIS 5670e User’s Manual Test page 288 Protocols Disable 234 Enable 234 Protocols and Datastreams 15 PRTnnnn Statement 89 PU 366 PU2.
PAGE 376
AXIS 5570e/AXIS 5670e User’s Manual SNA 367 SNA Printing 3174 CU Mode 48 5494 CU Mode 36, 60 Snap-in for iPrint 143 SNMP 199, 367 SSCP 367 SSL 231 SSL/TLS Status 235 Starting AXIS ThinWizard 189 Status file 194, 197 String Functions 222 String Substitutions 223, 251 Substitutions 223 Supported Printers 18, 290 Supported Protocols 291 Supported systems 291 Supported web browsers 291 Switched major node definitions 64 T TCP 367 Technical Specifications 286, 290 Test Button 17 Test button 288 Test page 2
PAGE 377
AXIS 5570e/AXIS 5670e User’s Manual LPD 177 PROS A 178 PROS B 178 Reverse Telnet 178 Upgrading 236 URL 368 User 181, 182 User Defined Strings 251 V View Certificate 235 VTAM 368 VTAM Logon-mode entry 63 W Web Flash Loading 230 WINS 32, 33 Wizard 368 World Wide Web 265 377