AXIS M1065-L Network Camera User Manual
About this Document This manual is intended for administrators and users of AXIS M1065-L Network Camera, and is applicable to firmware 6.15 and later. It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems may also be useful when developing shell scripts and applications. Later versions of this document will be posted at www.axis.com.
Battery The Axis product uses a 3.0 V BR1632 lithium battery as the power supply for its internal real-time clock (RTC). Under normal conditions this battery will last for a minimum of five years. Low battery power affects the operation of the RTC, causing it to reset at every power-up. When the battery needs replacing, a log message will appear in the product’s server report. For more information about the server report, see the product´s setup pages or contact Axis support.
AXIS M1065-L Network Camera Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hazard Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Other Message Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connectors and Buttons . . . . . .
AXIS M1065-L Network Camera Table of Contents Continuous Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date & Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS M1065-L Network Camera Safety Information Safety Information Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE TICE NO Indicates a situation which, if not avoided, could result in damage to property.
AXIS M1065-L Network Camera Hardware Overview Hardware Overview For specifications of the hardware components, see Technical Specifications on page 66. 1 2 3 4 5 6 7 8 9 10 11 Focus lock ring Focus ring IR LED PIR sensor Speaker Status LED Control button Not used Network connector PoE SD card slot Power connector Connectors and Buttons Network Connector RJ45 Ethernet connector with Power over Ethernet (PoE). NOTICE TICE NO The product shall be connected using a shielded network cable (STP).
AXIS M1065-L Network Camera Hardware Overview SD card slot NOTICE TICE NO • Risk of damage to SD card. Do not use sharp tools, metal objects or excessive force when inserting or removing the SD card. Use your fingers to insert and remove the card. • Risk of data loss and corrupted recordings. Do not remove the SD card while the product is running. Disconnect power or unmount the SD card from the Axis product’s webpages before removal. This product supports microSD/microSDHC/microSDXC cards (not included).
AXIS M1065-L Network Camera Access the Product Access the Product To install the Axis product, see the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. We recommend the following browsers: • Internet Explorer® with Windows® • Safari® with OS X® • ChromeTM or Firefox® with other operating systems. To view streaming video in Internet Explorer, allow installation of AXIS Media Control (AMC) when prompted. The Axis product includes one (1) H.
AXIS M1065-L Network Camera Access the Product Set the Root Password To access the Axis product, you must set the password for the default administrator user root. This is done in the Configure Root Password dialog, which opens when the product is accessed for the first time. To prevent network eavesdropping, the root password can be set via an encrypted HTTPS connection, which requires an HTTPS certificate.
AXIS M1065-L Network Camera Access the Product Click Snapshot to save a snapshot of the video image. This button is primarily intended for use when the AXIS Media Control viewer toolbar is not available. Enable this button from Live View Config > Action Buttons. The Audio clip drop-down list allows you to play an audio clip from the Live View page. Select the audio clip and click the Play button. Activate or de-activate IR illumination from Setup > Video & Audio > Camera Settings.
AXIS M1065-L Network Camera Access the Product For information about how to configure audio, see Set Up Audio on page 24. Speaker button — Click to turn the speakers on or off. Microphone button – Click to mute or unmute the microphone. In Simplex - speaker only mode, the Microphone and Talk buttons must both be active to send audio to the Axis product. Click either button to stop audio transmission. Use the slider to control the volume of the speakers and the microphone.
AXIS M1065-L Network Camera Media Streams Media Streams The Axis product provides several audio and video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, audio streams and to the list of available stream profiles. Other applications and clients can access video and audio streams directly, without going via the Live View page. How to Stream H.264 H.
AXIS M1065-L Network Camera Media Streams The AMC Control Panel can be used to configure various video and audio settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control Panel is automatically installed on first use, after which it can be configured. Open the AMC Control Panel from: • Windows Control Panel (from the Start screen or Start menu) • Alternatively, right-click the video image in Internet Explorer and click Settings.
AXIS M1065-L Network Camera Media Streams Note • = IP address • The Axis product supports QuickTime 6.5.1 and later. • QuickTime may add latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this.
AXIS M1065-L Network Camera Set Up the Product Set Up the Product The Axis product can be configured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have restricted access to settings, see Users on page 49 See also the online help .
AXIS M1065-L Network Camera Video and Audio Video and Audio The video and audio settings can be used to optimize video and audio quality. You can configure the following: • Video stream settings. See page 17. • Stream profiles. See page 19. • Camera settings. See page 20. • View area. See page 22. • Overlay image. See page 22. • Privacy mask. See page 24. • Audio settings. See page 24. • Audio clips. See page 25.
AXIS M1065-L Network Camera Video and Audio • Rotate image. If required, the image can be rotated. • Color setting. Select either Color or Black & White. Black & White uses less bandwidth than Color. • Maximum frame rate. To avoid bandwidth problems, the frame rate allowed to each viewer can be Limited to a fixed amount. Alternatively, the frame rate can be set as Unlimited, which means the Axis product always delivers the highest frame rate possible under the current conditions. • Overlay settings.
AXIS M1065-L Network Camera Video and Audio How to set an H.264 profile 1. To change the settings for all H.264 streams that do not use a stream profile, go to Video & Audio > Video Stream > H.264. 2. To increase or decrease the number of frames per GOP, set the GOP length. 3. Select one of the H.264 profiles. 4. Select on of the following: - Variable bit rate - Maximum bit rate 5. If you select Maximum bit rate, select which variable to prioritize in the Priority drop-down list. 6. Click Save.
AXIS M1065-L Network Camera Video and Audio Camera Settings The Video & Audio > Camera Settings page provides access to advanced image settings for the Axis product. Image Appearance To change Image Appearance go to the menus under Setup > Video & Audio > Camera Settings. Increasing the Color level increases the color saturation. The value 100 gives maximum color saturation and the value 0 gives minimum color saturation.
AXIS M1065-L Network Camera Video and Audio Shutter speed is related to the amount of time the shutter is opened and is measured in seconds (s). A slow shutter speed allows more light to reach the sensor and can help produce a brighter image in low light situations. On the other hand, a slow shutter speed can cause moving objects to appear blurry. Set Wide Dynamic Range to WDR Off and set Shutter to • Auto to set the shutter speed automatically.
AXIS M1065-L Network Camera Video and Audio Built-in IR Illumination WARNING Risk of eye injury. Do not look directly into the IR LED at short distance. Since the light provided from the IR LED is outside of the visible range, it is not possible to see if it is active. Use the camera to check if the IR illumination is active. The IR illumination can be activated or de-activated, and its intensity can be increased or decreased by moving the slider, from the product’s Live View page.
AXIS M1065-L Network Camera Video and Audio It is also possible to display text when an action rule is triggered, see How to include overlay text in an action rule on page 23. How to include overlay text 1. Go to Video & Audio > Video Stream and select the Image tab. 2. To include date and time, select Include date and Include time. 3. To include a text string, select Include text and enter the text in the field. Modifiers can be used, see File Naming & Date/Time Formats in the online help . 4.
AXIS M1065-L Network Camera Video and Audio 4. The Transparency Settings page is now displayed: - To make a color in the overlay image transparent, select Use transparency and enter the RGB hexadecimal value for the color. Example: To make white transparent, enter FFFFFF. For more examples of hexadecimal values, see the online help - . To scale the image automatically, select Scale with resolution. The image will be scaled down to fit the resolution used by the Axis product. 5. Click Save.
AXIS M1065-L Network Camera Video and Audio • Simplex – Network Camera microphone only - Audio captured by the product microphone is transmitted from the Axis product to one or more clients. To set the audio mode, go to Video & Audio > Audio Settings and select the desired mode from the Audio mode drop-down list. Audio Input Configure the audio input settings under Audio> Audio Settings. Source lists the built-in microphone. Use the Input gain to control the volume (dB Full Scale) of the audio input.
AXIS M1065-L Network Camera Configure the Live View Page Configure the Live View Page You can customize the Live View page and alter it to suit your requirements. It is possible to define the following features of the Live View page. • Stream Profile. See page 19. • Default Viewer for Browser. See page 26. • Viewer Settings. See page 26. • Action Buttons. These are the buttons described in Controls on the Live View Page on page 10. • User Defined Links. See page 27.
AXIS M1065-L Network Camera Configure the Live View Page User Defined Links To display user-defined links in the Live View page, select the Show custom link option, give the link a name and then enter the URL to link to. When defining a web link do not remove the 'http://' from the URL address. Custom links can be used to run scripts or activate external devices connected to the product, or they can link to a web page.
AXIS M1065-L Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) PTZ (pan, tilt and zoom) is available if you have enabled digital PTZ in the selected view area. For more information on view areas, see View Area on page 22. About preset positions A preset position is a saved view that can be used to quickly steer the camera to a specific position.
AXIS M1065-L Network Camera PTZ (Pan Tilt Zoom) The Panel Shortcut Command Buttons list shows the user-defined buttons that can be accessed from the Live View page’s Ctrl panel. These buttons can be used to provide direct access to commands issued using the VAPIX® application programming interface. Click Add to add a new shortcut command button.
AXIS M1065-L Network Camera Detectors Detectors About camera tampering Camera Tampering can generate an alarm when the camera is repositioned, or when the lens is covered, spray-painted or severely de-focused. To send an alarm, for example via email, an action rule must be set up. How to configure tampering detection 1. Go to Detectors > Camera Tampering. 2. Set the Minimum duration, that is the time that must elapse before an alarm is generated.
AXIS M1065-L Network Camera Detectors Once motion detection windows are configured, the Axis product can be configured to perform actions when motion is detected. Possible actions include uploading images and start recording. For more information, see Set Up Action Rules on page 41. Note • Using the motion detection feature may decrease the product’s overall performance. • The position of the Motion Detection Window is relative to the orientation of the Camera.
AXIS M1065-L Network Camera Detectors Note • To trigger on small objects or movements, use several small motion detection windows rather than one large window, and select a low object size. • To avoid triggering on small objects, select a high object size. • While monitoring an area where moving objects are not expected, select a high history level. This will cause motion detection to trigger as long as the object is present in the window. • To only detect flashing light, select a low sensitivity.
AXIS M1065-L Network Camera Applications Applications AXIS Camera Application Platform (ACAP) is an open platform that enables third parties to develop analytics and other applications for Axis products. For information about available applications, downloads, trials and licenses, go to www.axis.com/applications Note • Several applications can run at the same time but some applications might not be compatible with each other.
AXIS M1065-L Network Camera Applications If the Axis product is reset to factory default, uploaded applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings on page 61.
AXIS M1065-L Network Camera AXIS Video Motion Detection AXIS Video Motion Detection AXIS Video Motion Detection is an application that detects moving objects in the camera’s field of view. When a moving object is detected, AXIS Video Motion Detection sends an alarm that can be used by the Axis product or by third-party software to for example, record video or send a notification. AXIS Video Motion Detection 3 is included with the Axis product and is available under Setup > Applications.
AXIS M1065-L Network Camera AXIS Video Motion Detection 7. If too many unwanted objects are tracked, enable and configure one or more of the ignore filters. See Ignore Filters on page 37. After modifying a setting, click Save to apply the changes. The video stream will be restarted and it may take a few seconds before the change is applied. Include Area The include area is the area in which moving objects will be detected. Objects moving outside the include area will be ignored.
AXIS M1065-L Network Camera AXIS Video Motion Detection To highlight the exclude areas, click on the icon. Visual Confirmation Visual confirmation is used to validate that the settings are correct, that is, that all objects that should be detected are detected. Visual confirmation is used to validate that the settings are correct, that is, that all objects that should be tracked are tracked. Note To use visual confirmation, Internet Explorer and AXIS Media Control (AMC) must be used.
AXIS M1065-L Network Camera AXIS Video Motion Detection ponds or large trees, use exclude areas instead of the filter. The filter will be applied to all moving objects in scene and, if set to a value too large, important objects might not be detected. The swaying object filter is used to avoid tracking objects that only move a short distance, for example moving trees, flags and their shadows. Use the filter if such objects cause a lot of unwanted tracked objects.
AXIS M1065-L Network Camera AXIS Video Motion Detection 1. Select the Short-lived objects option. 2. Enter the number of seconds in the field. The number of seconds is the minimum time that must pass before the object is detected. Start with a small number. 3. Enter the number of seconds in the field. The number of seconds is the minimum time that must pass before tracking starts. Start with a small number. 4. Click Save to apply the filter. 5. Use visual confirmation to verify the settings. 6.
AXIS M1065-L Network Camera AXIS Video Motion Detection 1. Insert an SD card in the Axis product, or go to Setup > System Options > Storage in the Axis product’s webpages and configure the product to use a network share. 2. Optionally, go to Setup > Video & Audio > Stream Profiles and create a stream profile to use for recording. 3. Go to Setup > Events > Action Rules and click Add to create a new action rule. 4. From the Trigger drop-down list, select Applications and then select VMD 3DigitalAutoTracking.
AXIS M1065-L Network Camera Events Events The Event pages allow you to configure the Axis product to perform actions when different events occur. For example, the product can start a recording or send an email notification when motion is detected. The set of conditions that defines how and when the action is triggered is called an action rule.
AXIS M1065-L Network Camera Events • • • • - Virtual Inputs – can be used by a VMS (Video Management System) to trigger actions. Virtual inputs can, for example, be connected to buttons in the VMS user interface. - Moving – Trigger the rule when the camera view moves due to a PTZ operation. This can for example be used as an additional condition to prevent an action rule triggered by motion detection to record video while the camera view moves due to a PTZ operation.
AXIS M1065-L Network Camera Events • Status LED – Flash the LED indicator. This can for example be used to validate triggers such as motion detection during product installation and configuration. • WDR Mode – The WDR Mode can be turned on or off when the action rule is triggered. Add Recipients The product can send media files and messages to notify users about events. Before the product can send media files or notification messages, you must define one ore more recipients.
AXIS M1065-L Network Camera Events Network Share A network share can also be used as a storage device for recorded video. Go System Options > Storage to configure a network share before setting up a continuous recording or an action rule to record video. For more information about storage devices, see Storage on page 57.
AXIS M1065-L Network Camera Events 3. Click OK. To use the recurrence in an action rule, first select Time from the Trigger drop-down list in the Action Rule Setup page and then select the recurrence from the second drop-down list. To modify or remove recurrences, select the recurrence in the Recurrences List and click Modify or Remove.
AXIS M1065-L Network Camera Recordings Recordings The Axis product can be configured to record video continuously or according to an action rule: • To start a continuous recording, see page 47. • To set up action rules, see page 41. • To access recordings, see Find Recordings on page 46. • To play recordings, see Play Recording on page 46. • To export a recording as a video clip, see Export Video Clip on page 47. • To configure camera controlled storage, see Storage on page 57.
AXIS M1065-L Network Camera Recordings To play a recording, follow these steps: 1. Go to Recordings > List. 2. To reduce the number of recordings displayed, select the desired options under Filter and click the Filter button to apply the filters. See also Find Recordings on page 46. 3. Select the recording and click Play. The recording will be played in a new browser window. Export Video Clip Recordings on the SD card or network share can be exported as video clips.
AXIS M1065-L Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. To switch languages, go to Setup > Languages and first upload the new language file. Browse and locate the file and click the Upload Language button. Select the new language from the list and click Save.
AXIS M1065-L Network Camera System Options System Options Security Users User access control is enabled by default and can be configured under System Options > Security > Users. An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may access the Live View page.
AXIS M1065-L Network Camera System Options HTTPS HTTPS (HyperText Transfer Protocol over Secure Socket Layer, or HTTP over SSL) is a web protocol providing encrypted browsing. HTTPS can also be used by users and clients to verify that the correct device is being accessed. The security level provided by HTTPS is considered adequate for most commercial exchanges. The Axis product can be configured to require HTTPS when users from different user groups (administrator, operator, viewer) log in.
AXIS M1065-L Network Camera System Options About certificates Certificates are used to authenticate devices on a network. Typical applications include encrypted web browsing (HTTPS), network protection via IEEE 802.1X and secure upload of images and notification messages for example via email. Two types of certificates can be used with the Axis product: Server/Client certificates - To authenticate the Axis product. A Server/Client certificate can be self-signed or issued by a Certificate Authority (CA).
AXIS M1065-L Network Camera System Options • Synchronize with NTP Server – Obtains date and time from an NTP server. With this option, date and time settings are updated continuously. For information on NTP settings, see NTP Configuration on page 54. If using a host name for the NTP server, a DNS server must be configured. See DNS Configuration on page 54. • Set manually – Allows you to manually set date and time. If using an NTP server, select your Time zone from the drop-down list.
AXIS M1065-L Network Camera System Options 3. Open a command prompt and enter the following commands: Linux/Unix syntax arp -s temp ping -s 408 Linux/Unix example arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.
AXIS M1065-L Network Camera System Options Note AXIS Internet Dynamic DNS Service requires IPv4. Advanced TCP/IP Settings DNS Configuration DNS (Domain Name Service) provides the translation of host names to IP addresses. The DNS settings are configured under System Options > Network > TCP/IP > Advanced. Select Obtain DNS server address via DHCP to use the DNS settings provided by the DHCP server.
AXIS M1065-L Network Camera System Options To enable HTTPS, go to System Options > Security > HTTPS. For more information, see HTTPS on page 50. NAT traversal (port mapping) for IPv4 A network router allows devices on a private network (LAN) to share a single connection to the Internet. This is done by forwarding network traffic from the private network to the “outside”, that is, the Internet.
AXIS M1065-L Network Camera System Options QoS (Quality of Service) QoS (Quality of Service) guarantees a certain level of a specified resource to selected traffic on a network. A QoS-aware network prioritizes network traffic and provides a greater network reliability by controlling the amount of bandwidth an application may use. The QoS settings are configured under System Options > Network > QoS. Using DSCP (Differentiated Services Codepoint) values, the Axis product can mark different types of traffic.
AXIS M1065-L Network Camera System Options RTP/H.264 The RTP port range and multicast settings are configured under System Options > Network > RTP. The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used. Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.
AXIS M1065-L Network Camera System Options 4. The card can now be removed. Format SD Card NOTICE TICE NO Formatting the SD card will remove all data and recordings stored on the card. The Axis product can be configured to automatically format SD cards that are inserted into the product. If autoformat is enabled and an SD card is inserted, the product will check if the SD card has the ext4 file system. If the card has a different file system, the card will automatically be formatted to ext4.
AXIS M1065-L Network Camera System Options 7. Click Mount to mount the SD card. It is possible to change the passphrase without reformatting the card. Open Storage Management, click Encrypt and enter the old and new passphrases. The passphrase can only be changed when the card is mounted. Changing the passphrase does not disrupt ongoing recordings. To disable encryption, unmount the SD card and follow the steps above but clear the Enable SD card encryption option.
AXIS M1065-L Network Camera System Options • uploaded applications are kept but must be restarted Click Default to reset all settings, including the IP address, to the factory default values. This button should be used with caution. The Axis product can also be reset to factory default using the control button, see Reset to Factory Default Settings on page 61. To identify the product or test the Status LED, click Flash LED under Identify and specify the duration in seconds, minutes or hours.
AXIS M1065-L Network Camera System Options Axis strongly recommends that you do not use this function unless you understand the consequences. Axis Support does not provide assistance for problems with customized scripts. To open the Script Editor, go to System Options > Advanced > Scripting. If a script causes problems, reset the product to its factory default settings, see page 61. For more information, see www.axis.
AXIS M1065-L Network Camera Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your first actions when troubleshooting a problem should be to check the current firmware version. The latest version may contain a correction that fixes your particular problem. The current firmware version in the Axis product is displayed in the page Setup > Basic Setup and in Setup > About.
AXIS M1065-L Network Camera Troubleshooting 3. Open a browser and type in the product’s IP address. In the page that opens, use the Browse button to select the upgrade file to use. Then click Load to restart the upgrade process. 4. After the upgrade is complete (1–10 minutes), the product automatically restarts and shows a steady green on the Status indicator. 5. Reinstall the product, referring to the Installation Guide.
AXIS M1065-L Network Camera Troubleshooting The product is accessible locally but not externally Router configuration To configure your router to allow incoming data traffic to the Axis product, enable the NAT-traversal feature which will attempt to automatically configure the router to allow access to the Axis product, see NAT traversal (port mapping) for IPv4 on page 55. The router must support UPnPTM. Firewall protection Check the Internet firewall with your network administrator.
AXIS M1065-L Network Camera Troubleshooting No audio Incorrect setup Check the sound card in the computer. Ensure that mute is not selected and that the volume settings are correct. Check that Enable audio support is selected under Setup > System Options > Security > Audio Support. Check that the correct Audio Input source is selected under Setup > Video & Audio > Audio Settings. Poor audio quality Stuttering Reduce the number of listeners and viewers. Decrease image resolution and compression.
AXIS M1065-L Network Camera Technical Specifications Technical Specifications You can find the latest version of the technical specifications at www.axis.com Camera Image sensor 1/3" progressive scan RGB CMOS Lens Fixed focal length, 2.8 mm, F2.0 Horizontal field of view: 110° Vertical field of view: 61° M12 mount, fixed iris, IR corrected Day and night Automatically removable IR cut filter Minimum illumination Color: 0.25 lux at 50 IRE F2.0 B/W: 0.05 lux at 50 IRE F2.
AXIS M1065-L Network Camera Technical Specifications Analytics AXIS Video Motion Detection 3, Audio detection Support for AXIS Camera Application Platform, AXIS Cross Line Detection, AXIS Digital Autotracking and third-party applications, see www.axis.
AXIS M1065-L Network Camera Technical Specifications General Casing Polycarbonate, Aluminium, recycled plastic Color: White NCS S 1002-B For repainting instructions of skin cover or casing and impact on warranty, contact your Axis partner. Sustainability PVC free, 64% recycled plastic Memory 512 MB RAM, 256 MB Flash Power Power over Ethernet (PoE) IEEE 802.3af/802.3at Type 1 Class 2 Typical 2.7 W, max 4.8 W 4.75–5.25 V DC, typical 2.5 W, max 4.
AXIS M1065-L Network Camera Technical Specifications Performance Considerations When setting up your system, it is important to consider how various settings and situations will affect performance. Some factors affect the amount of bandwidth (the bit rate) required, others can affect the frame rate, and some affect both. If the load on the CPU reaches its maximum, this will also affect the frame rate.
User Manual AXIS M1065-L Network Camera © Axis Communications AB, 2016 Ver. M1.18 Date: August 2016 Part No.
