User manual

ManualsBrandsAxis Communications ManualsOtherWebcam P1357

AXISP13Series

AXISP1354NetworkCamera

AXISP1357NetworkCamera

ENGLISH

InstallationGuide

Summary of content (20 pages)

PAGE 1
AXIS P1354 Network Camera AXIS P1357 Network Camera Installation Guide ENGLISH AXIS P13 Series
PAGE 2
Legal Considerations Regulatory Information Video and audio surveillance can be regulated by laws that vary from country to country. Check the laws in your local region before using this product for surveillance purposes. This product includes one (1) H.264 decoder license and one (1) AAC decoder license. To purchase further licenses, contact your reseller. Europe Liability Every care has been taken in the preparation of this document.
PAGE 3
This product fulfills the requirements for immunity according to EN 55024 office and commercial environments Australia/New Zealand This digital equipment fulfills the requirements for RF emission according to the Class B limit of AS/NZS CISPR 22. The product shall be connected using a shielded network cable (STP) that is properly grounded.
PAGE 4
PAGE 5
AXIS P13 Series Safety Information Read through this Installation Guide carefully before installing the product. Keep the Installation Guide for future reference. Hazard Levels Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
PAGE 6
AXIS P13 Series Safety Instructions WARNING • The Axis product shall be installed by a trained professional. NOTICE TICE NO • The Axis product shall be used in compliance with local laws and regulations. • To use the Axis product outdoors, or in similar environments, it shall be installed in an approved outdoor housing. • Store the Axis product in a dry and ventilated environment. • Avoid exposing the Axis product to shocks or heavy pressure.
PAGE 7
AXIS P13 Series WARNING • Risk of explosion if the battery is incorrectly replaced. • Replace only with an identical battery or a battery which is recommended by Axis. • Dispose of used batteries according to local regulations or the battery manufacturer's instructions.
PAGE 8
PAGE 9
AXIS P13 Series Installation Guide This Installation Guide provides instructions for installing AXIS P1354/P1357 Network Camera on your network. For other aspects of using the product, see the User Manual available at www.axis.com Installation Steps Package Contents • • • • • • Network Camera AXIS P1354 AXIS P1357 Terminal block connector 4-pin connector block for connecting external devices to the I/O terminal connector 2x terminal connector 2-pin STR 2.
PAGE 10
AXIS P13 Series Hardware Overview 4 2 3 5 1 11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 12 8 9 6 13 7 14 Focus puller Zoom puller LED indicator Power LED Network LED Control button I/O terminal block Iris connector Power connector* RS485/422 SD card slot (microSD) Audio in Audio out Network connector PoE * Not used for -E versions.
PAGE 11
AXIS P13 Series LED Indicators Note • The Status LED can be configured to be unlit during normal operation. To configure, go to Setup > System Options > Ports & Devices > LED. See the online help for more information. • The Status LED can be configured to flash while an event is active. • The Status LED can be configured to flash for identifying the unit. Go to Setup > System Options > Maintenance . Indication Green Steady green for normal operation.
PAGE 12
AXIS P13 Series Connectors and Buttons For specifications and operating conditions, see page 13. Network Connector RJ45 Ethernet connector with Power over Ethernet (PoE). NOTICE TICE NO The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network shall be intended for their specific use. Make sure that the network devices are installed in accordance with the manufacturer’s instructions.
PAGE 13
AXIS P13 Series RS485/RS422 Connector Two terminal blocks for RS485/RS422 serial interface used to control auxiliary equipment such as pan-tilt devices. SD Card Slot NOTICE TICE NO • Risk of damage to SD card. Do not use sharp tools or excessive force when inserting or removing the SD card. This product supports microSD/microSDHC/microSDXC cards (not included). For SD card recommendations, see www.axis.com Control Button For location of the control button, see Hardware Overview on page 10.
PAGE 14
AXIS P13 Series Power Consumption Products DC PoE AXIS P1354 8-28 V DC max 7.2 W IEEE 802.3af/802.3at Type 1 Class 3 AXIS P1357 8-28 V DC max 7.9 W IEEE 802.3af/802.3at Type 1 Class 3 Connectors I/O Connector 4–pin terminal block For an example diagram, see Connection Diagrams on page 16. Function Pin 0 V DC (-) 1 Notes Specifications DC output 2 Can be used to power auxiliary equipment. Note: This pin can only be used as power out. 3.
PAGE 15
AXIS P13 Series Audio Connector 3.5 mm audio connectors (stereo) 3 1 Tip 2 1 2 Ring 3 Sleeve Microphone/Line in Ground Audio Output Line out (mono) Ground RS485/422 Connector Two 2-pin terminal blocks for RS485/RS422 serial interface.
PAGE 16
AXIS P13 Series Connection Diagrams I/O Connector 1 2 3 4 1 2 3 4 0 V DC (-) DC output 3.3 V, max 50 mA Digital input 0 to max 40 V DC Digital output 0 to max 40 V DC, open drain, 100 mA Install the Hardware Connect the Cables 1. Connect external input/output devices if required, such as alarm devices. For information about the terminal connector pins, see page 14 . 2. Connect an active speaker and/or external microphone if required. 3. Connect the camera to the network using a shielded network cable.
PAGE 17
AXIS P13 Series - Connect an external power adapter to the power connector block. For wiring information, see page 14. 5. Check that the indicator LEDs indicate the correct conditions, see LED Indicators on page 11 . Access the Product The product can be used with most operating systems and browsers. The recommended browsers are • Internet Explorer® with Windows® • Safari® with OS X® • ChromeTM or Firefox® with other operating systems.
PAGE 18
AXIS P13 Series 7. On the Focus page, click Fine-tune focus automatically and wait until automatic fine tuning is completed. 8. Click Enable iris. If the button is inactive the iris is already enabled. 9. If needed, make further adjustments under the Advanced tab. See the online help for more information. Focus Assistant To focus using the Focus Assistant, follow the instructions in steps 1–3 on page 17 before you start with the steps below.
PAGE 19
AXIS P13 Series Reset to Factory Default Settings Important Reset to factory default should be used with caution. A reset to factory default will reset all settings, including the IP address, to the factory default values. Note The installation and management software tools are available from the support pages on www.axis.com/techsup 1. Disconnect power from the product. 2. Press and hold the control button and reconnect power. See Hardware Overview on page 10. 3.