AXIS 241Q and AXIS 241S Video Servers User’s Manual Installation instructions are also available in German, French, Italian and Spanish in this manual.
About This Document This manual is intended for administrators and users of the AXIS 241Q/241S Video Server, and is applicable for software release 4.20. It includes instructions for installing, using and managing the AXIS 241Q/241S on your network. Previous experience of networking will be of use when installing and using this product. Some knowledge of UNIX or Linux-based systems would also be beneficial, for developing shell scripts and applications.
AXIS 241Q/241S Table of contents Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Hardware Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 AXIS 241Q Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 AXIS 241S Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS 241Q/241S Event Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Event Servers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Event Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS 241Q/241S Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Montage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Videokameras anschließen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Installationsmethoden . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS 241Q/241S - Product Description Product Description The AXIS 241Q/241S is a fully featured video server for security surveillance and remote monitoring needs. Based on the AXIS ARTPEC-2 compression chip, it can digitize up to 4 analog video sources and make these available on the network as real-time, full frame rate Motion JPEG and/or MPEG-4 video streams. The AXIS 241Q has 4 BNC inputs for analog video devices and the AXIS 241S has 1 BNC input and a matching loop-through output.
AXIS 241Q/241S - Product Description AXIS 241Q Front Panel Indicators - After completion of the startup and self-test routines, the multi-colored Network, Status, Power Indicators flash as follows: Network Status Power Amber Flashes for activity on a 10 Mbit/s network Green Flashes for activity on a 100 Mbit/s network Red Flashes rapid red for hardware error, together with the Status indicator None No connection Green Normal operation Amber Flashes during reset to factory default or at firmw
AXIS 241Q/241S - Product Description AXIS 241S Front Panel Indicators - After completion of the startup and self test routines, the multi-colored Network, Status, Power Indicators flash as follows: Network Status Power Amber Flashes for activity on a 10 Mbit/s network Green Flashes for activity on a 100 Mbit/s network Red Flashes rapid red for hardware error, together with the Status indicator None No connection Green Normal operation Amber Flashes during reset to factory default or at fi
AXIS 241Q/241S - Product Description AXIS 241Q/241S Rear Panel The Serial Number is located on the label on the underside of the unit. Power Supply Connector - A single socket for connection of the PS-K power adapter. I/O Terminal connector - The I/O Terminal connector provides the physical interface to 4 digital transistor outputs, 4 digital inputs and an RS-485 interface. See Unit Connectors, on page 48 for more information.
AXIS 241Q/241S - Installation Installation Mounting The AXIS 241Q/241S is supplied with a mounting kit for wall or rack mounting. The mounting brackets can be positioned for mounting the video server on a vertical surface or in a rack (4U). Follow the instructions below to attach the brackets to the video server: ❶ Slide the grey frame off the front panel of the video server (no tools needed). ❶ ❷ Insert the metal plates in the slots on each side of the video server.
AXIS 241Q/241S - Installation Connecting video cameras Coaxial cable Connect the video output of your camera(s) to the AXIS 241Q/241S video server using a standard 75 Ohm coaxial video cable with BNC connectors. Note: Use a RCA-to-BNC adapter if your camera has a standard phono-type (RCA) connector. Installation Methods The AXIS 241Q/241S is designed for installation on an Ethernet network. This involves assigning it an IP address, either manually or via an automated network service (DHCP).
AXIS 241Q/241S - Installation Set the IP address manually If the AXIS 241Q/241S does not appear in the window, click the Refresh button to try again. If it still does not appear, set the IP address manually. 1. Acquire an unused IP address. AXIS IP Utility detects the subnet your computer is connected to. The AXIS 241Q/241S must be installed on the same network segment. 2. Click the button “Set IP address using serial number” and enter the serial number and IP address for the AXIS 241Q/241S. 3.
AXIS 241Q/241S - Installation ARP and Ping in Windows Assign your product a unique IP address from a computer on your network as follows: 1. Acquire an unused IP address for the AXIS 241Q/241S from your network administrator. 2. Connect the AXIS 241Q/241S to the network using a standard network cable. 3. Locate the serial number (S/N) found on the label on the underside of the AXIS 241Q/241S. 4. From a computer on your network, open a Command Prompt, i.e. from the Windows Start menu, select Run...
AXIS 241Q/241S - Installation ARP and Ping in UNIX/Linux Assign your product with a unique IP address from a computer on your network, as follows: 1. Acquire an unused IP address for the AXIS 241Q/241S from your network administrator. 2. Connect the AXIS 241Q/241S to the network using a standard network cable. 3. Locate the serial number (S/N) found on the label on the underside of the AXIS 241Q/241S. Syntax: arp -s temp ping -s 408 Example: arp -s 192.168.0.
AXIS 241Q/241S - Installation AXIS Internet Dynamic DNS Service The AXIS Internet Dynamic DNS Service is a free service provided by Axis. The service allows you to quickly and simply install your video server, which then receives a static name (DNS name) and a dynamic IP address. More information about the AXIS Internet Dynamic DNS Service is available at www.axiscam.net The video server can be unregistered from the service at any time. Please visit www.axiscam.
AXIS 241Q/241S - Using the video server Using the video server The AXIS 241Q/241S can be used with most standard operating systems and supports Microsoft Internet Explorer 5.x or later. Other browsers may impose limitations when using the AXIS 241Q/241S. For more information please see www.axis.com/techsup Accessing the video server 1. Start your browser. 2. Enter the IP address or host name of the AXIS 241Q/241S in the Location/Address field of your browser. 3.
AXIS 241Q/241S - Using the video server The Live View page If the AXIS 241Q/241S has been customized, the buttons and other items described below will be displayed accordingly on the Live View page. The following provides an overview of each button: To resize the displayed image, click the View Size buttons: half-size (x1/2), full-size (x1), x2 or x4. This will not change the resolution of the image (not available in Sequence Mode).
AXIS 241Q/241S - Using the video server The Snapshot button takes a snapshot of the currently displayed image. The Snapshot function and the target directory for saving snapshots can be configured from AMC (AXIS Media Control), which is available from the Windows Control Panel (Internet Explorer only). Click the View Full Screen button and the video image will fill the entire screen area. No other windows will be visible. Press Esc (Escape) on your keyboard to cancel full screen view.
AXIS 241Q/241S - Video Streams Video Streams The AXIS 241Q/241S provides several different image and video stream formats. The type to use depends on your requirements and on the properties of your network. The Live View page in the AXIS 241Q/241S provides access to Motion JPEG and MPEG-4 video streams, as well as to single JPEG images. Other applications and clients can also access these video streams/images directly, without going via the Live View page.
AXIS 241Q/241S - Video Streams MPEG-4 protocols and communication methods To deliver live streaming video over IP networks, various combinations of transport protocols and broadcast methods are employed. • RTP (Realtime Transport Protocol) is a protocol that allows programs to manage the real-time transmission of multimedia data, via unicast or multicast. • RTSP (Real Time Streaming Protocol) serves as a control protocol, to negotiate which transport protocol to use for the stream.
AXIS 241Q/241S - Video Streams RTP/RTSP This unicast method is RTP tunneled over RTSP. This can be used to exploit the fact that it is relatively simple to configure firewalls to allow RTSP traffic. RTP/RTSP/HTTP or RTP/RTSP/HTTPS These two methods can also be used to traverse firewalls. Firewalls are commonly configured to allow the HTTP protocol, thus allowing RTP to be tunneled.
AXIS 241Q/241S - Video Streams Other MPEG-4 clients Although it may be possible to use other clients to view the MPEG-4 stream, this is not guaranteed by Axis. For some other clients, e.g. QuickTime™ the Video Object Type must be set to Simple. It may also be necessary to adjust the advanced MPEG-4 settings. To assess the video stream from e.g. QuickTime™ the following path can be used: rtsp:///mpeg4/#/media.
AXIS 241Q/241S - Configuring the video server Configuring the video server This section describes how to configure the AXIS 241Q/241S and is intended for: • administrators, who have unrestricted access to all the Setup tools • operators, who have access to the Video & Image, Live View Config and Event Configuration settings. The AXIS 241Q/241S is configured from the Setup link, in a standard browser (see Technical Specifications, on page 57).
AXIS 241Q/241S - Video & Image Settings Video & Image Settings The following descriptions show examples of the available features in the AXIS 241Q/241S. For details of each setting, please refer to the online help available from each page. Click to access the online help. Image Settings Image Appearance Modify the Image Appearance to optimize the video images according to your requirements.
AXIS 241Q/241S - Video & Image Settings Overlay Settings Use these settings to include a) an image as an overlay, and/or b) the date and time, along with text of your own. Overlay text Overlay image Text overlays are all included on one line at the top or bottom of the video image. Image overlays can be placed anywhere in the video image. To upload an overlay image, see below.
AXIS 241Q/241S - Video & Image Settings Pan Tilt Zoom The settings here are for configuring preset positions and the PTZ Control Queue. For detailed information on these settings, please see the online help. For an overview of Pan Tilt Zoom functionality, please see page 37. Advanced - MPEG-4 Settings Tools for adjusting the MPEG-4 settings and for controlling the video bit rate. The MPEG-4 standard provides many different coding tools for various applications in different situations.
AXIS 241Q/241S - Video & Image Settings Overlay Image Settings An overlay image is an image superimposed over the video image. Follow these instructions to upload and use an overlay image: 1. To upload the file (the image) to the AXIS 241Q/241S, click the Browse button and locate it on your computer or server. 2. Click the Upload button and follow the on-screen instructions. 3. The image is now available in the Use overlay image drop-down list. 4. Click Save.
AXIS 241Q/241S - Live View Config Live View Config Layout These are the tools for deciding the layout of the Live View page. The layout can be set in 3 ways: • Use Axis look - the layout is unchanged. • Use custom settings - modify the default page with your own colors, images etc. Click the Configure button and see the following page. • Own Home Page - Upload and use your own custom made page as the default web page. Click the Configure button and see the following page.
AXIS 241Q/241S - Live View Config Upload Own Web Files Your own web files, background picture, color etc. must first be uploaded to the AXIS 241Q/241S in order to be available for selection in the Custom Settings setup dialog. Once uploaded, the files are shown in the drop-down list. 1. Enter the path to the file, e.g. a file located on your workstation or click the Browse button. 2. Select the user level for the uploaded file.
AXIS 241Q/241S - Live View Config 6. Enter the cgi link: http://192.168.0.125/axis-cgi/com/ptz.cgi?camera=1&continuouspantiltmove=0,0 7. These links will appear in the web interface and can be used to control the PTZ camera For more information on the Axis HTTP API, see the Support / Developer pages on the Axis Web site at http://www.axis.com. See also the section on PTZ, on page 37. Action Buttons These buttons can be used to manually trigger and stop an event from the Live View page.
AXIS 241Q/241S - Live View Config HTML Examples You can add live video from your AXIS 241Q/241S to your own web site. The video server can send Motion-JPEG or MPEG-4 images to up to 20 simultaneous connections, although an administrator can restrict this to fewer. This does not affect or include the number of multicast viewers. Enter the Image Type, Image size and other settings to suit your web page and click Update.
AXIS 241Q/241S - Event Configuration Event Configuration This section describes how to configure the AXIS 241Q/241S for alarm handling. Various actions can be configured to run when certain types of events occur. Event type A set of parameters describing how and when the video server is to perform certain actions Triggered Event (see page 33) - the circumstances that start an event e.g.
AXIS 241Q/241S - Event Configuration Event Types An Event Type is a set of parameters describing how and when the video server is to perform certain actions. Example: If somebody walks past the connected camera, and an event has been configured to act on this, the video server can e.g. record and send video images to an FTP server, or send a notification email to a pre-configured email address with a pre-configured message. Video images can be sent as an attachment with the email.
AXIS 241Q/241S - Event Configuration Pre-trigger and Post-trigger buffers This function is very useful when checking to see what happened immediately before and after a trigger, e.g. 2 minutes before and after a door was opened. Check the Upload images checkbox under Event Types > Add Triggered... > Triggered by... to expand the web page with the available options. Buffer size - AXIS 241Q - up to 36 MB buffer; AXIS 241S - up to 9 MB buffer.
AXIS 241Q/241S - Event Configuration 7. Click OK to save the Event in the Event Types list. Please see the online help for descriptions of each available option. Motion Detection In the Motion Detection menu, you can configure the video source(s) for motion detection. The motion detection feature is used to generate an alarm whenever movement occurs (or stops) in the image. The AXIS 241Q can use a maximum of 40 Include/Exclude windows, whilst the AXIS 241S can use a maximum of 10.
AXIS 241Q/241S - Event Configuration 6. Adjust the size (drag the bottom right-hand corner) and position (click on the text at the top and drag to the desired position). 7. Adjust the Object size, History and Sensitivity profile sliders (see table below for details). Any detected motion within an active window is then indicated by red peaks in the Activity window (the active window has a red frame). 8. Click Save.
AXIS 241Q/241S - Pan Tilt Zoom Pan Tilt Zoom If the AXIS 241Q/241S has been appropriately configured, the Live View page will display the controls available for the installed Pan Tilt Zoom (PTZ) device. The administrator can enable/disable the controls for specified users. Video sources Preset positions Tilt bar (relative) The exact controls shown depends on the make and model of PTZ device. There may be e.g.
AXIS 241Q/241S - Pan Tilt Zoom In contrast, when using an absolute driver, each position on the bar (see right) represents a defined position in the device’s range of movement, with the center of the bar representing the point midway between the two extremes of movement. Clicking a position directly on the bar moves the camera directly to the new position in one smooth movement. Clicking on the arrows at the ends of a bar causes a stepped, incremental change.
AXIS 241Q/241S - Pan Tilt Zoom Installing PTZ Devices The AXIS 241Q/241S supports several PTZ devices. Please see www.axis.com for a complete list of supported devices, and to obtain the correct driver. Follow the instructions below to install a PTZ device: 1. Using an appropriate cable, connect the device to your selected port (RS-232 or RS-485). These ports are available via the D-Sub connector and the I/O terminal connector, respectively. See pages 48 and 49 for more information. 2.
AXIS 241Q/241S - System Options System Options Security User access control is enabled by default, when the administrator sets the root password on first access.
AXIS 241Q/241S - System Options HTTPS For greater security, the AXIS 241Q/241S can be configured to use HTTPS (Hypertext Transfer Protocol over SSL (Secure Socket Layer)). That is, all communication that would otherwise go via HTTP will instead go via an encrypted HTTPS connection.
AXIS 241Q/241S - System Options Date & Time Format Used in Images - specify the formats for the date and time (12h or 24h) displayed in the Live View video streams. Use the predefined formats or use your own custom date and time formats. See File Naming & Date/Time Formats in the online help for information on how to create your own file formats.
AXIS 241Q/241S - System Options Network - Advanced TCP/IP Settings DNS Configuration DNS (Domain Name Service) provides the translation of host names to IP addresses on your network. Obtain DNS server address via DHCP - automatically use the DNS server settings provided by the DHCP server. Click the View button to see the current settings.
AXIS 241Q/241S - System Options Network Traffic The default setting is Auto-negotiate which means that the correct speed is automatically selected. If necessary, you can set the connection speed by selecting it from the drop-down list. Maximum bandwidth - Specify, in Mbit/s or kbit/s, the maximum bandwidth that the video server is allowed to use on your network. This is a useful function when connecting your video server to busy or heavily loaded networks. The default setting is Unlimited.
AXIS 241Q/241S - System Options Ports & Devices I/O Ports - the pinout, interface support and the control and monitoring functions provided by this connector are described in Unit Connectors, on page 48. Maintenance • Restart - The unit is restarted without changing any of the settings. Use this method if the unit is not behaving as expected. • Restore - The unit is restarted and most current settings are reset to factory default values.
AXIS 241Q/241S - System Options Support The support overview page provides valuable information on troubleshooting and contact information, should you require technical assistance. Logs & Reports - when contacting Axis support, please be sure to provide a valid Server Report with your query. View Information - The Log report and the Parameter List also provide valuable information for troubleshooting and when contacting Axis’ support service.
AXIS 241Q/241S - System Options Resetting to the Factory Default Settings To reset the AXIS 241Q/241S to the original default settings, go to the System Options > Maintenance web page (described in Maintenance, on page 45) or use the control button on the AXIS 241Q/241S, as described below: Using the Control Button Follow the instructions below to reset the AXIS 241Q/241S to the factory default settings using the Control Button. 1. Switch off the AXIS 241Q/241S by disconnecting power. 2.
AXIS 241Q/241S - Unit Connectors Unit Connectors The following connectors are described in this section: • • • • The D-Sub Connector, on page 48 The I/O Terminal Connector, on page 49 COM Ports RS-232 and RS-485, on page 50 Y/C to BNC Cable (AXIS 241S only), on page 51 The D-Sub Connector The AXIS 241Q/241S provides one 9-pin D-sub connector, providing the physical interface for an RS-232 port, used for connecting accessory equipment; such as stand-alone PTZ devices for the remote control of connected
AXIS 241Q/241S - Unit Connectors The I/O Terminal Connector This section describes the pinout and interface support provided by the 12-pin I/O terminal connector, which includes: • • • • 4 digital transistor outputs 4 digital inputs an RS-485 interface auxiliary power and GND The terminal connector is used in applications for e.g. motion detection, event triggering, time lapse recording, alarm notification via email, image storage to FTP locations, etc. • Inputs - e.g. a push button.
AXIS 241Q/241S - Unit Connectors Schematic Diagram - I/O Terminal Connector Switch Mode Power Supply 3.3V AXIS 241Q/241S Video Server + o PS-K 9W o z 1 o GND 2 o e.g.
AXIS 241Q/241S - Unit Connectors Y/C to BNC Cable (AXIS 241S only) The AXIS 241S supports conversion from Y/C (S-video) to composite video using an Y/C to BNC cable. The cable is available as an accessory - see the Axis Web site at: http://www.axis.com. Follow these instructions to connect the Y/C to BNC cable: 1. Connect the BNC connector marked IN to the Video In connector on the video server. 2. Connect the BNC connector marked OUT to the Video OUT connector on the video server. 3.
AXIS 241Q/241S - Troubleshooting Troubleshooting Checking the Firmware Firmware is software that determines the functionality of the AXIS 241Q/241S. One of your first actions when troubleshooting a problem should be to check the currently installed version. The latest version may contain a correction that fixes your particular problem. The current firmware version in your AXIS 241Q/241S can be seen under Setup > Basic Configuration.
AXIS 241Q/241S - Troubleshooting Emergency Recovery Procedure If power or the network connection to the AXIS 241Q/241S is lost during the upgrade, the process will fail and the unit will become unresponsive. A flashing red Status LED indicates a failed upgrade. To recover the unit, follow the steps below. The serial number is found on the underside label on the product casing. 1.
AXIS 241Q/241S - Troubleshooting Symptoms, Possible Causes and Remedial ActionsI Problems setting the IP address Using ARP/Ping - the IP address Restart the server and try again. Ensure also the ping length is set to 408. See or ARP and Ping must be set within two minutes in Windows on page 13, or ARP and Ping in UNIX/Linux on page 14. after power has been applied to the video server The video server is located on a different subnet.
AXIS 241Q/241S - Troubleshooting No images displayed in the Web interface Problem with AMC (Internet Explorer only) To enable the updating of images in Microsoft Internet Explorer, set your Web browser to allow ActiveX controls. Also, make sure that AXIS Media Control (AMC) component is installed on your workstation.
AXIS 241Q/241S - Troubleshooting Poor rendering of MPEG-4 images. Color depth set incorrectly on clients. Set to 16-bit or 32-bit color. If text overlays are blurred, or if there are other rendering problems, you may need to enable Advanced Video Rendering. This is done on the MPEG-4 tab in the AMC control panel applet. Ensure that your graphics card is using the latest device driver. The latest drivers can usuallly be downloaded from the manufacturer's web site.
AXIS 241S/241Q - Technical Specifications Technical Specifications Item Specification Models • AXIS 241Q: 4-channel video server • AXIS 241S: 1-channel video server Video compression • Motion-JPEG, including single snapshot JPEG images.
AXIS 241S/241Q - Technical Specifications Item Specification Power • External power adapter PS-K (included): 9V DC, 9W • Via terminal connector: 7-20V DC, max 8W Operating conditions • Temperature: 5oC (41oF) to 50oC (122oF) • Humidity: 20-80% RH (non-condensing) System integration support • API for software integration available at www.axis.
AXIS 241S/241Q - Technical Specifications General performance considerations When setting up your system, it is important to consider how various settings and situations will affect performance. Some factors affect the amount of bandwidth (the bit rate) required, others can affect the frame rate, and some will affect both. If the load on the CPU reaches its maximum, this will also affect the frame rate.
AXIS 241S/241Q - Technical Specifications Frame rates - Motion JPEG The following test results show the frame rates in frames/second (fps) for Motion JPEG streams from the AXIS 241S/241Q, using a compression level of 50%. Note that these values are guidelines only - actual values may vary.
AXIS 241S/241Q - Technical Specifications Bandwidth As there are many factors affecting bandwidth, it is very difficult to predict the required amounts. The settings that affect bandwidth are: • • • • • • the image resolution the image compression the frame rate the MPEG-4 object type the MPEG-4 GOV structure the analog cameras connected to the video server There are also factors in the monitored scene that will affect the bandwidth.
AXIS 241Q/241S - Installation Installation Montage Im Lieferumfang des AXIS 241Q/241S ist ein Montagesatz für die Wandanbringung oder den Rackeinbau enthalten. Die Halterungen können so montiert werden, dass der Videoserver auf einer senkrechten Fläche angebracht oder in ein Rack (4 HE) eingebaut werden kann. Gehen Sie folgendermaßen vor, um die Halterungen an den Videoserver anzubringen: ❶ Ziehen Sie den grauen Rahmen vorn am Videoserver ab (kein Werkzeug erforderlich).
AXIS 241Q/241S - Installation Videokameras anschließen Schließen Sie den Video-Ausgang Ihrer Kamera(s) mit einem Standard-Koaxial-Videokabel (75 Ohm) mit BNC-Anschlüssen an den AXIS 241Q/241S Videoserver an. Koaxial-Kabel Hinweis: Verwenden Sie einen RCA/BNC-Adapter, falls Ihre Kamera über einen RCA-Anschluss verfügt. Installationsmethoden Der AXIS 241Q/241S ist für die Installation in einem Ethernet-Netzwerk vorgesehen.
AXIS 241Q/241S - Installation AXIS IP Utility AXIS IP Utility ist eine kostenlose Windows-Anwendung, mit der Axis-Geräte im Netzwerk erkannt und angezeigt werden. Die Anwendung dient außerdem zum manuellen Festlegen einer statischen IP-Adresse. Sie können AXIS IP Utility von den Supportseiten unter www.axis.com/techsup/software herunterladen. Automatische Erkennung 1. Prüfen Sie, ob Netzwerk- und Stromkabel mit dem AXIS 241Q/241S verbunden sind. 2. Starten Sie AXIS IP Utility.
AXIS 241Q/241S - Installation 7. Die Installation ist damit abgeschlossen. Fahren Sie mit dem Abschnitt Using the video server, auf Seite 16 fort. Die Seriennummer (S/N) befindet sich auf dem Etikett auf der Unterseite des AXIS 241Q/241S. UPnP™ Die UPnP-Funktionalität des AXIS 241Q/241S ist standardmäßig aktiviert.
AXIS 241Q/241S - Installation Beispiel 6. Starten Sie den AXIS 241Q/241S, bzw. starten Sie ihn neu. Der Start/Neustart muss binnen zwei Minuten nach Eingabe der Befehle "ARP" und "Ping" erfolgen. 7. Sobald "Antwort von 192.168.0.125: ..." angezeigt wird, also nach ca. 10–15 Sekunden, können Sie den Ping-Befehl durch Betätigen von Ctrl+C stoppen. 8. Starten Sie einen Webbrowser, und geben Sie im Adressfeld die IP-Adresse ein. 9. Betätigen Sie die Eingabetaste. 10.
AXIS 241Q/241S - Installation ARP and Ping unter UNIX/Linux Gehen Sie folgendermaßen vor, um Ihrem Produkt von einem Computer Ihres Netzwerks aus eine eindeutige IP-Adresse zuzuweisen: 1. Lassen Sie sich von Ihrem Netzwerkadministrator eine nicht zugewiesene IP-Adresse für den AXIS 241Q/241S geben. 2. Schließen Sie den AXIS 241Q/241S über ein Standard-Netzwerkkabel an das Netzwerk an. 3. Die Seriennummer (S/N) ist auf dem Etikett auf der Unterseite des AXIS 241Q/241S zu finden.
AXIS 241Q/241S - Installation AXIS Internet Dynamic DNS Service Der AXIS Internet Dynamic DNS Service wird von Axis als kostenloser Service zur Verfügung gestellt. Damit können Sie Ihren Videoserver schnell und einfach installieren. Der Videoserver erhält dabei einen statischen Namen (DNS-Namen) und eine dynamische IP-Adresse. Weitere Einzelheiten zum AXIS Internet Dynamic DNS Service erhalten Sie unter www.axiscam.net.
AXIS 241Q/241S - Installation Hinweis: MC muss installiert sein, damit direkt übertragene Bilder im Microsoft Internet Explorer angezeigt werden können. Falls in Ihrer Arbeitsumgebung die Installation weiterer Softwarekomponenten nicht zugelassen ist, können Sie Ihren AXIS 241Q/241S so konfigurieren, dass zum Aktualisieren der Bilder ein Java-Applet verwendet wird.
AXIS 241Q/241S - Installation Installation Montage Votre AXIS 241Q/241S est équipé d’un kit de montage pour support mural ou sur baie (rack). Les supports de montage peuvent être positionnés pour monter le serveur vidéo sur une surface verticale ou dans une baie (4U). Suivez les instructions ci-dessous pour fixer les supports de montage au serveur vidéo : ❶ Faites glisser la structure du panneau avant du serveur pour l’enlever (pas besoin d’outils).
AXIS 241Q/241S - Installation Connexion des caméras vidéo Câble coaxial Connectez la sortie vidéo de votre ou vos caméras à votre AXIS 241Q/241S à l’aide d’un câble vidéo coaxial standard de 75 Ohms avec connecteurs BNC. Remarque : Utilisez un adaptateur RCA/BNC si votre caméra dispose d’un connecteur de type phono (RCA). Méthodes d’installation Votre AXIS 241Q/241S est conçu pour une installation dans un réseau Ethernet.
AXIS 241Q/241S - Installation Détection automatique 1. Vérifiez que les câbles d'alimentation et le réseau sont bien raccordés à votre AXIS 241Q/241S. 2. Démarrez AXIS IP Utility. Double-cliquez sur l’icône AXIS 241Q/241S lorsqu’elle apparaît dans la fenêtre de façon à en ouvrir la page d’accueil. Définissez manuellement l’adresse IP. Si AXIS 241Q/241S ne s’affiche pas, cliquez sur le bouton Actualiser pour réessayer. Si l’icône ne s’affiche toujours pas, définissez l’adresse IP manuellement. 1.
AXIS 241Q/241S - Installation UPnP™ La fonction UPnPest activée par défaut dans votre AXIS 241Q/241S. Si elle est aussi activée sur votre ordinateur (Windows ME ou XP), le serveur vidéo sera automatiquement détecté et une nouvelle icône sera ajoutée à « Mes emplacements réseau ». Cliquez sur cette icône pour accéder à votre AXIS 241Q/241S.
AXIS 241Q/241S - Installation 6. Démarrez/redémarrez votre AXIS 241Q/241S. Vous devez le faire dans les 2 minutes qui suivent la saisie des commandes ARP et Ping. 7. Lorsque le message « Reply from 192.168.0.125: ... » (Réponse de) s’affiche (au bout d’environ 10-15 secondes), tapez Ctrl+C pour fermer la session Ping. 8. Lancez un navigateur Web et entrez l’adresse IP dans le champ Adresse/emplacement. 9. Appuyez sur Entrée. 10. Entrez un mot de passe pour l’utilisateur root (administrateur). 11.
AXIS 241Q/241S - Installation ARP et Ping sous UNIX/Linux Affectez une adresse IP unique à votre ordinateur à partir d’un ordinateur du réseau, en procédant comme suit : 1. Trouvez une adresse IP non utilisée pour votre AXIS 241Q/241S en la demandant à votre administrateur de réseau. 2. Connectez votre AXIS 241Q/241S à votre réseau à l’aide d’un câble de réseau standard. 3.
AXIS 241Q/241S - Installation AXIS Internet Dynamic DNS Service AXIS Internet Dynamic DNS Service est un service gratuit offert par Axis pour vous permettre d’installer rapidement et facilement votre serveur vidéo, qui reçoit ainsi un nom statique (nom DNS) et une adresse IP dynamique. Davantage d’informations sur l’AXIS Internet Dynamic DNS Service sont disponibles sur le site www.axiscam.net. Le serveur vidéo peut être désactivé à tout moment. Visitez www.axiscam.
AXIS 241Q/241S - Installation 7. Le cas échéant, acceptez l’installation de AMC sur votre station de travail. Remarque : AMC doit être installé pour visionner les images en direct dans Microsoft Internet Explorer. Si votre environnement de travail limite les composants logiciels supplémentaires, vous pouvez configurer votre AXIS 241Q/241S pour utiliser un applet Java pour mettre à jour les images.
AXIS 241Q/241S - Installazione Installazione Montaggio AXIS 241Q/241S comprende un kit per montaggio a parete o su rack. Le staffe di montaggio possono essere posizionate per montare il server video su una superficie verticale o in un armadio rack (4U). Seguire le istruzioni in basso per collegare le staffe al server video: ❶ Estrarre il telaio grigio dal pannello anteriore del server video (non sono necessari attrezzi).
AXIS 241Q/241S - Installazione Connessione delle videocamere Collegare l’uscita video delle videocamere al server video AXIS 241Q/241S utilizzando un cavo coassiale standard 75 Ohm con connettori BNC. Nota: Utilizzare un convertitore RCA-BNC se la Cavo coassiale videocamera è dotata di un connettore standard RCA. Metodi di installazione L'AXIS 241Q/241S è progettata per l'installazione in una rete Ethernet.
AXIS 241Q/241S - Installazione Rilevamento automatico 1. Controllare che i cavi di rete e di alimentazione siano collegati all'AXIS 241Q/241S. 2. Avviare AXIS IP Utility. Quando l’AXIS 241Q/241S verrà visualizzata, fare doppio clic su di essa per aprirne l'home page. Impostazione manuale dell'indirizzo IP Se l'AXIS 241Q/241S non viene visualizzata all'interno della finestra, fare clic sul pulsante Aggiorna per effettuare un nuovo tentativo.
AXIS 241Q/241S - Installazione UPnP™ La funzionalitàUPnP è attiva per impostazione predefinita nell’AXIS 241Q/241S. Se è abilitata anche sul computer in uso (con sistema operativo Windows ME o XP), il server video verrà automaticamente rilevato e verrà aggiunta una nuova icona in "Risorse di rete". Fare clic su questa icona per accedere all'AXIS 241Q/241S. Nota: Per installare il servizio UPnP sul computer, aprire il Pannello di controllo dal menu Start e selezionare Installazione applicazioni.
AXIS 241Q/241S - Installazione 7. Quando viene visualizzato ‘Reply from 192.168.0.125: ...’ (circa 10-15 secondi), digitare Ctrl+C per interrompere la sessione Ping. 8. Avviare un browser Web e immettere l’indirizzo IP nel campo Indirizzo/Posizione. 9. Premere Invio. 10. Immettere una password per l’utente root (amministratore). 11. Se necessario, accettare l’installazione di AMC sulla workstation. Nota: AMC deve essere installato per visualizzare le immagini dal vivo in Internet Explorer di Microsoft.
AXIS 241Q/241S - Installazione ARP e Ping in UNIX/Linux Assegnare al prodotto un indirizzo IP unico da un computer della rete, come segue: 1. Ottenere un indirizzo IP non utilizzato per l'AXIS 241Q/241S dall’amministratore di rete. 2. Collegare l’AXIS 241Q/241S alla rete mediante un cavo di rete standard. 3. Individuare il numero di serie (S/N) sull'etichetta sulla parte inferiore dell'AXIS 241Q/241S. Sintassi: arp -s temp ping -s 408 Esempio: arp -s 192.168.
AXIS 241Q/241S - Installazione Servizio AXIS Internet Dynamic DNS Il servizio AXIS Internet Dynamic DNS è un servizio gratuito fornito da Axis, che consente di installare in modo rapido e facile il server video, che riceve un nome statico (nome DNS) e un indirizzo IP dinamico. Ulteriori informazioni sul servizio AXIS Internet Dynamic DNS sono disponibili all'indirizzo www.axiscam.net. La registrazione per l’assistenza del server video può essere annullata in qualsiasi momento.
AXIS 241Q/241S - Installazione Nota: AMC deve essere installato per visualizzare le immagini dal vivo in Internet Explorer di Microsoft. Se l’ambiente di lavoro non consente l’aggiunta di componenti software, è possibile configurare AXIS 241Q/241S in modo da utilizzare un’applet Java per l’aggiornamento delle immagini.
AXIS 241Q/241S - Instalación Instalación Montaje El AXIS 241Q/241S se suministra con un kit especial para montaje de pared o sobre un bastidor (rack). Los soportes de montaje se pueden colocar de manera que servidor de vídeo pueda montarse en una superficie vertical o sobre un bastidor (4U). Siga las instrucciones siguientes para fijar los soportes de montaje en el servidor de vídeo: ❶ Retire el armazón gris del panel frontal del servidor de vídeo (no necesita herramientas).
AXIS 241Q/241S - Instalación Conexión de las cámaras de vídeo Conecte la salida de vídeo de su(s) cámara(s) al servidor de vídeo AXIS 241Q/241S utilizando un cable de vídeo coaxial de 75 ohmios con conectores BNC. Cable coaxial Notas: Utilice un adaptador de RCA a BNC si su cámara tiene un conector estándar tipo fono (RCA). Métodos de instalación El AXIS 241Q/241S está diseñado para instalarse en una red Ethernet.
AXIS 241Q/241S - Instalación Detección automática 1. Compruebe que los cables de red y alimentación estén conectados al AXIS 241Q/241S. 2. Inicie AXIS IP Utility. Cuando aparezca el AXIS 241Q/241S en la ventana, haga doble clic en el icono para abrir la página de inicio. Configuración manual de la dirección IP Si el AXIS 241Q/241S no aparece en la ventana, haga clic en el botón Actualizar y vuelva a intentarlo. Si sigue sin aparecer, defina la dirección IP manualmente. 1.
AXIS 241Q/241S - Instalación UPnP™ La funcionalidad UPnP está habilitada de forma predeterminada en el AXIS 241Q/241S. Si también está habilitada en su equipo (Windows ME o XP), el servidor de vídeo detectará la cámara automáticamente y agregará un nuevo icono a “Mis sitios de red”. Haga clic en este icono para acceder al AXIS 241Q/241S. Nota: Para instalar el servicio UpnP en su equipo, abra el Panel de control desde el menú Inicio y seleccione Agregar o quitar programas.
AXIS 241Q/241S - Instalación 7. Cuando aparezca ‘Reply from 192.168.0.125: ...’ (aproximadamente 10-15 segundos), presione Ctrl+C para detener Ping. 8. Inicie un navegador e introduzca la dirección IP en el campo Dirección/Ubicación. 9. Presione Intro. 10. Introduzca una contraseña para el usuario root (administrador). 11. Si es necesario, acepte la instalación de AMC en su estación de trabajo. Nota: AMC debe estar instalado para ver vídeos en vivo en Microsoft Internet Explorer.
AXIS 241Q/241S - Instalación El AXIS Internet Dynamic DNS Service El AXIS Internet Dynamic DNS Service es un servicio gratuito de Axis, que le permite instalar su servidor de vídeo de forma rápida y sencilla y, después, recibir un nombre estático (nombre DNS) y una dirección IP dinámica. Encontrará más información sobre el AXIS Internet Dynamic DNS Service en www.axiscam.net El servidor de vídeo puede darse de baja del servicio en cualquier momento.
AXIS 241Q/241S - Glossary Glossary ActiveX - A control (or set of rules) used by a browser. ActiveX controls are often downloaded and installed automatically as required. API - Application Programming Interface. The Axis API can be used for integrating Axis products into other applications. ARP - Address Resolution Protocol. Used to associate an IP address to a hardware MAC address. A request is broadcast on the local network to find out what the MAC address is for the IP address.
AXIS 241Q/241S - Glossary TCP/IP - Transmission Control Protocol/Internet Protocol. A suite of network protocols that determine how data is transmitted. TCP/IP is used on many networks, including the Internet. TCP keeps track of the individual packets of information and IP contains the rules for how the packets are actually sent and received.
AXIS 241Q/241S - Index Index A Accessing the video stream 21 Action 32 Action buttons 17, 30 Active/Inactive 17, 30 Administrators 23, 40 Advanced TCP/IP settings 43 Alarm 32, 35, 49 Allowed IP addresses 40 AMC 16, 21, 74 Anonymous viewers 40 ARP and Ping 13 AXIS Internet Dynamic DNS Service 15, 42 AXIS IP Utility 11 B Backup 45 Bandwidth 19, 61 Basic TCP/IP settings 42 Buffers 34 C CGI links 29, 38 Click-in-image 38 COM Port RS-485 50 Constant bit rate 19 Control button 7, 8, 47 Customize 28 D D
AXIS 241Q/241S - Index 95 MPEG-4 protocols 20 MPEG-4 settings 44 Multicasting 20 N Network indicator 8 Network settings 42 Network traffic 44 Notification of IP address change 42 O Operators 40 Output buttons 17, 30 Overlays 25, 27 Own home page 29 Own web files 29 P Pan/Tilt/Zoom 37, 50 Pinout - I/O connectors 49 Port status 36 Ports & Devices 44 Post-trigger buffer 34 Preset positions 38 Pre-trigger buffer 34 PTZ commands 29, 38 PTZ control queue 38 Pulse 17, 30 Q Quad stream 17, 26 R Recovery 5
