AXIS 2420 AXIS 2420 W/Lens Network Camera User’s Manual
AXIS 2420 User’s Manual 2 About This Document Liability This manual is intended for administrators and users of the AXIS 2420 and the AXIS 2420 W/Lens Network Camera, and is applicable for software release 2.31. Both products are referred to throughout as the AXIS 2420. Readers are recommended to use this document as a supplement to the Wizards and other on-line information available via the Web-based interface. Later versions of this manual will be posted to the Axis Website, as required.
AXIS 2420 User’s Manual Table of Contents Table of Contents An Introduction to the AXIS 2420 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Camera Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deutsch AXIS 2420 User’s Manual Deutsch Physische Beschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Bedienfeld vorn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Bedienfeld hinten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Montage der AXIS 2420 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS 2420 User’s Manual An Introduction to the AXIS 2420 An Introduction to the AXIS 2420 Camera Models The AXIS 2420 Network Camera is available in 4 different variants: • • • • The AXIS 2420 (PAL) - supplied without a lens. The AXIS 2420 W/Lens (PAL) - supplied with a DC-Iris varifocal lens. The AXIS 2420 (NTSC) - supplied without a lens. The AXIS 2420 W/Lens (NTSC) - supplied with a DC-Iris varifocal lens.
An Introduction to the AXIS 2420 AXIS 2420 User’s Manual To simplify the installation process, the Web-based interface provides an Installation Wizard and an Application Wizard, which help you towards a seamless and automated integration into your networking and application environments.
AXIS 2420 User’s Manual An Introduction to the AXIS 2420 Outdoor Use - The AXIS 2420 is a professional product including full DC-iris control and is shipped either without a lens (AXIS 2420) or with a DC-Iris varifocal lens (AXIS 2420 W/Lens). Both variants can alternatively be fitted with any standard C-CS type lens. Installed into an appropriate outdoor housing, the camera makes an ideal remote monitoring tool for outdoor use.
An Introduction to the AXIS 2420 AXIS 2420 User’s Manual Modem Support - The Point to Point Protocol (PPP) support allows you to use your AXIS 2420 remotely over a serial link, just as if it were located on your local network. You can initially set up the AXIS 2420 over the network, or use a computer connected directly to the AXIS 2420 via the supplied Null Modem cable. The AXIS 2420 is accessed using a standard Dial-up (PPP) connection.
AXIS 2420 User’s Manual Physical Description Physical Description Please read the following information to familiarize yourself with your AXIS 2420, making particular note of where the connectors and indicators are located. This section provides a useful reference when installing the product. Front Panel Status Indicator Used in conjunction with the Focus Assistant, this multi-colored indicator can be used as a local focusing aid (see Focusing Your Camera, on page 17).
Physical Description AXIS 2420 User’s Manual Rear Panel RS-232 Serial Connector A single 9-pin D-sub connector provides the RS-232 serial interface for connecting a modem or the AXIS 2191 Audio Module. For pinout information, refer to Appendix F - The Unit Connectors. Power Supply Connector PS-D connector for connection of the AXIS 2420 power supply.
AXIS 2420 User’s Manual Checking The Hardware Inventory Mounting the AXIS 2420 The AXIS 2420 is supplied without a mounting assembly. Screw holes for attaching the camera to an assembly are provided on both the top and bottom surfaces of the unit, for easy installation on a wall or from a ceiling. The screw hole has an internal dimension of 1/4" UNC. Screw holes on top and base.
Installing on a Network AXIS 2420 User’s Manual Installing on a Network • Macintosh users - Please refer to Notes for Macintosh Users, on page 53. • Easy installation - Use The AXIS IP Installer. See Using the AXIS IP Installer, on page 52. • Quick installation - Follow the instructions below to install the AXIS 2420 on an Ethernet network. ❶ Fit or replace a lens (if required). The lens is fitted by turning it in a clockwise direction. ❷ Note the Serial number on the underside of the unit.
AXIS 2420 User’s Manual Installing on a Network ❺ Attach the external Power Supply to the unit and connect it to your local mains supply. ❻ Approximately 10-15 seconds after connecting the power supply, the message ‘Reply from 172.21.1.200...’ - or similar, is returned in the DOS/command window. Ensure that the Power Indicator is permanently lit and that the Network Indicator flashes intermittently. Power Supply Connector ❼ Exit ping.
Installing via a Modem AXIS 2420 User’s Manual Installing via a Modem The information in this section describes how to connect the AXIS 2420 to a serial modem for transmitting images over a dial-up connection. Important! • Although instructions for configuring the AXIS 2420 using a null modem cable are provided below, it is recommended that (if possible) the unit is initially installed and configured over a network.
AXIS 2420 User’s Manual Installing via a Modem Creating a Dial-Up Networking Connection Follow the steps below to create a dedicated Dial-Up networking connection to your product: ❶ Double-click My Computer and then double-click the Dial-Up Networking icon. ❷ Double-click the Make New Connection icon. ❸ Provide the connection with a name (AxisCamera is the name used in these examples). ❹ From the drop-down list, select the Standard Modem previously created for the AXIS 2420. Click Configure...
Installing via a Modem AXIS 2420 User’s Manual Refining the Dial-Up Networking Properties Having created the Dial-Up connection for your AXIS 2420, follow the steps below to refine the connection properties: ❺ Click TCP/IP settings and then check the Server assigned IP address, and Server assigned name server addresses radio buttons. ❶ From the Dial-Up Networking dialog, right-click the dedicated Dial-Up connection previously created for your AXIS 2420 (AxisCamera in this example). Select Properties.
AXIS 2420 User’s Manual Focusing Your Camera Verifying the Modem Connection and Completing the Installation Having initiated your Dial-Up connection, as described above, you can quickly test the connection by accessing the AXIS 2420 from a standard browser, such as Netscape or Internet Explorer, as follows: abc.xyz ❶ Since the AXIS 2420 emulates a DNS server, you can type in any URL containing a period in the address field of your browser to display the AXIS 2420 Home Page, as shown here.
Configuring Your Camera AXIS 2420 User’s Manual Configuring Your Camera Before you begin: Successful installation of the product is prerequisite to configuring the unit. You should therefore read the following information before commencing with this section: • Installing on a Network, on page 12, or Installing via a Modem, on page 14, and then • Choosing Your Application, on page 31. Important! Javascript must be enabled in your browser for the AXIS 2420 Web-based interface to work.
AXIS 2420 User’s Manual Configuring Your Camera The Installation Wizard The Installation Wizard provides a quick and easy way of defining the basic settings for your installation - as explained in the Administration Tools Overview, on page 21. Using the Installation Wizard 1. Start the Installation Wizard from the product’s Home Page or from the administration tools page. 2. Click Start>. Follow the instructions to complete the configuration. 3. Click the Finish button to save the settings to the camera.
Configuring Your Camera AXIS 2420 User’s Manual The Administration Tools Whether you are viewing images directly over the network, or transmitting images over a modem, you can use the Web-based Administration Tools for configuring and managing your AXIS 2420 at any time. After initially setting up the AXIS 2420 with the Installation Wizard, these tools are ideal for more advanced users. Accessing the Tools Follow the instructions below to access the Administration Tools using a browser: 1.
AXIS 2420 User’s Manual Configuring Your Camera 3. The Administration Tools are now presented as links on the Administration Page. Simply click the relevant link for the parameters you want to configure. Administration Tools Overview The table below provides a one-stop overview of the Administration Tools: Settings Image Tool Description Focus the camera using the Focus Assistant, adjust the Auto Iris settings, and define image attributes for your AXIS 2420.
Configuring Your Camera AXIS 2420 User’s Manual Applications Operation Tool Description Choose to run your AXIS 2420 in Sequential or Alarm Mode, and specify how and where images will be uploaded. Note that you must enable your application by following the Enable link. If there is already an older application present, then this must first be disabled before you enable your new application. Motion Detection Create and enable in-picture motion detection windows.
AXIS 2420 User’s Manual Configuring Your Camera System Security To prevent unauthorized use of the camera, the AXIS 2420 supports multi-user password protection, and access can be restricted to defined users only. A system Administrator has unrestricted access to the product´s Administration Tools and can determine the registration and access rights for all users.
Configuring Your Camera AXIS 2420 User’s Manual Motion Detection The AXIS 2420 includes in-picture motion detection, for creating specific surveillance zones in the image area. You can create, name, and use up to 3 motion detection windows. You can also move, resize, or delete them at any time. Use motion detection to generate an alarm whenever movement occurs in the specified area. Simply click and drag with your mouse in the image area to create and automatically enable a motion detection window.
AXIS 2420 User’s Manual Configuring Your Camera 4. Set the Size, History and Sensitivity profile sliders accordingly for the surveillance area. The sliders are described briefly below. A fuller description is provided in the on-line help. •Size - The relative size of the moving object in the motion detection window. •History - Specifies for how long a moving object will trigger the motion detection before being regarded as non-moving.
Configuring Your Camera AXIS 2420 User’s Manual Modem The Modem page allows you to set your specific modem type and configure it, using the following parameters: • Disable incoming calls - use this only if you will not need to dial-in to the AXIS 2420. • Modem Type - set the brand of modem and provide a specific Initstring, if required. • Communication Settings - advanced settings for your modem. Please see the documentation for your modem. • Callback - use this to get your modem to return your call.
AXIS 2420 User’s Manual Configuring Your Camera Connecting PTZ Devices The diagram below illustrates how the AXIS 2420 connects to your workstation and PTZ device. AXIS 2420 PTZ Driver Network Connection PC Browser Administration Tools RS-485 RS-232 Device contolled via RS-232 or RS-485/422 External PTZ Device Installation Procedure Follow the instructions below to install a PTZ device: 1. Attach the PTZ device to the RS-232 or RS-485/422 port of the AXIS 2420 using the appropriate cable. 2.
Configuring Your Camera AXIS 2420 User’s Manual When using a Pan-Tilt device, the camera’s home page will show Pan and Tilt bars, as well as a drop-down list for preset positions, if this is supported. Note that the presence and appearance of some functions (e.g. the zoom function) will depend on the Pan-Tilt device being used.
AXIS 2420 User’s Manual Configuring Your Camera Preset Positions To enable quick and accurate camera positioning to known camera hotspots, the Administrator can set and save any camera orientation as a named entity - a Preset Position, which can be used at any time. The orientation for the camera is controlled by Pan and Tilt control bars. Follow the instructions below to define a preset position: 1. From the COM-Port page, click the Preset Position button.
The Factory Default Settings AXIS 2420 User’s Manual The Factory Default Settings In certain circumstances, it may be necessary to reinstate the Factory Default settings for your AXIS 2420. This is performed by clicking the appropriate button in the Administration Tools, or by pressing the Control Button (see the illustration on page 9). Follow the instructions below to reinstate the product factory default settings using the Control Button: 1.
AXIS 2420 User’s Manual Choosing Your Application Choosing Your Application The AXIS 2420 can be used in a wide variety of applications and installs directly onto an Ethernet network, or over a V.90-compatible modem. Requiring no additional software on your viewing desktop, it is a completely self contained unit that delivers crisp live images to your browser. Using the Web-based Administration Tools and easy-to-use Wizards, you can quickly and easily develop your application.
Choosing Your Application 32 AXIS 2420 User’s Manual Picture frequency for Networking Applications When used in a TCP/IP networking environment, the AXIS 2420 delivers up to 30/25 (NTSC/PAL) images/second.
AXIS 2420 User’s Manual Choosing Your Application Modem Applications If a local network connection is not available at your chosen point of installation, you can alternatively connect your AXIS 2420 to a V.90-compatible modem and quickly configure any number of exciting applications using the Wizards; including: • Using Motion Detection to generate alarms and trigger uploads of recorded images.
Choosing Your Application AXIS 2420 User’s Manual Picture Frequency for Modem Applications The speed of your modem link is a dominant factor in determining the frequency at which images are displayed in your browser, and an average-sized image is normally transmitted in 2-4 seconds. For alarm applications, where picture updating is critical, images are buffered into internal memory prior to being uploaded to your ISP or Web server.
AXIS 2420 User’s Manual Choosing Your Application Sequentially Uploading Images to an FTP Server/ISP Ideal for busy Web sites on large or small networks, this application uploads images to an FTP server/ISP, via the network or a modem, and is perfect for applications where a large audience is expected. Your images can then be accessible to several specific users, or to the whole Internet community! You can select any of the ISPs in the Application Wizard, or specify your own.
Choosing Your Application AXIS 2420 User’s Manual Uploading Pre and/or Post Alarm Images to an FTP server/ISP The AXIS 2420 is the ideal solution for a wide variety of surveillance and process control applications. By connecting your external alarm devices to the I/O connector (see Appendix F - The Unit Connectors), you can quickly configure the product to upload single images, or send pre/post alarm image sequences to an FTP server or ISP when an event occurs.
AXIS 2420 User’s Manual Choosing Your Application Viewing live Images in a Browser This application represents the most basic application using a network camera. It is ideally suited for occasionally-visited sites on both large corporate networks, and SOHO (Small-Office Home-Office) applications, where a small network is installed and maintained.
The AXIS 2191 Audio Module 38 AXIS 2420 User’s Manual The AXIS 2191 Audio Module The AXIS 2191 Audio Module is an add-on device that provides audio capability to Axis network cameras. The module connects quickly and easily to the serial port of the camera and is configured and controlled via the camera’s user interface. The AXIS 2191 is supplied separately.
AXIS 2420 User’s Manual The AXIS 2191 Audio Module The Front Panel Serial Port Connector - Connect the serial cable from here to the serial port on the camera. Power Connector Power Indicator - Normally lit. Activity Indicator - Lights up when the camera has configured the audio module. The Rear Panel In 3.5mm socket for connection of external microphone. Volume In Level control for input. Use a screwdriver to adjust. Mic Built-in omni-directional microphone.
The AXIS 2191 Audio Module AXIS 2420 User’s Manual Installing the Audio Module ❶ Before installing the AXIS 2191 Audio Module, first install your network camera. Refer to the installation section of this manual. If you intend running the audio module in full-duplex mode, check that the sound card on your computer supports this. ❷ If using an external microphone, connect it to the socket provided. To use an alternative input device, (e.g. CD-player or radio) connect it to Line-In on the terminal block.
AXIS 2420 User’s Manual The AXIS 2191 Audio Module Configuring the Audio Module The network camera’s administration pages provide all the tools required for successfully configuring the AXIS 2191. From the camera’s home page, click on the link to Administration Tools. A new page containing the tools will open. To complete the configuration of your audio module, follow these instructions: 1.From the Admin tools, click External Devices. Select the AXIS 2191 Audio Module as the device to use. Click Save.
The AXIS 2191 Audio Module AXIS 2420 User’s Manual Using the Audio Module with Your Camera Your audio module is now configured and ready for use with your network camera. Enter your camera’s IP-address in Internet Explorer, or click Home on the camera’s admin page. You should then see the control panel for the AXIS 2191 below the camera image. If no audio controls are visible, check that you have made the correct setting under External Devices. NB.
AXIS 2420 User’s Manual The AXIS 2191 Audio Module Simplex - Talk Simplex - Talk mode means that only the web-client end of the connection can transmit audio (that is, to the AXIS 2191). This could be used, for example, to provide spoken instructions to a person seen in the network camera. This mode also requires you to use the Push-to-Talk button. Simplex - Listen Simplex - Listen mode can only receive audio from the AXIS 2191 to the web-client.
The AXIS 2191 Audio Module AXIS 2420 User’s Manual Troubleshooting the Audio Module Symptoms No audio controls below camera image. Possible causes The AXIS 2191 is not selected as the external device. Wrong camera firmware. No sound from the AXIS 2191 or from a PC trying to access a web page containing audio content. Incorrect settings or faulty connections. No audio signal from PC to the AXIS 2191 when passing a proxy server. No full-duplex function. Poor performance.
AXIS 2420 User’s Manual The AXIS 2191 Audio Module Technical Specifications for the AXIS 2191 • Operating temperature: 40-105oF (5-40oC). • Humidity - 8-80% relative humidity. • EMC : EN55024, EN55022, Class B and EN61000-3-3. • EMC - FCC Class A of FCC Rules and Regulations part 15, subpart B. • EMC • Full-duplex audio: Audio data encoded in ADPCM format at 32kbps, 8 kHz sampling (G.721). Data is sent using HTTP. • 9-pin D-SUB serial connector: RS-232. • Power Input: Axis PS-D power supply.
The AXIS 2191 Audio Module AXIS 2420 User’s Manual The Audio Module to Camera Serial Cable The serial cable supplied with your AXIS 2191 is wired as shown in the table below: Pinouts for the RS-232 Port Audio Pin Pin Camera Signal IN 1 1 IN CD IN 2 2 IN RXD OUT 3 3 OUT TXD OUT 4 4 OUT DTR GND 5 5 GND GND IN 6 6 IN DSR OUT 7 7 OUT RTS IN 8 8 IN CTS Unused 9 9 IN RI
AXIS 2420 User’s Manual Troubleshooting Appendix A - Troubleshooting This appendix provides useful information to help you to resolve any difficulty you might have with your AXIS 2420. Symptoms, possible causes and remedial actions are provided in a quick reference table. PINGing Your IP Address By sending a packet to the specified address and waiting for a reply, the PING utility can determine whether a specific IP address is accessible.
Troubleshooting AXIS 2420 User’s Manual Symptoms, Possible Causes and Remedial Actions Symptoms The AXIS 2420 cannot be accessed from a Web browser. Possible causes The IP address is already being used by another device. Remedial actions 1. Disconnect your AXIS 2420 from the network. 2. Run the PING utility (as described in PINGing Your IP Address, on page 47) and follow the appropriate recommendations.
AXIS 2420 User’s Manual Symptoms The Network indicator displays red. Possible causes Faulty cabling. Troubleshooting Remedial actions 1. To verify that the cable is functional, connect the cable to a known functioning device on the network and PING it from your workstation. 2. If the cabling is OK and your network is reachable, you should receive a reply similar to this: Reply from : bytes = 32; time = 10 ms..... The Active and Network indicators are flashing every 0.5 seconds.
Troubleshooting Symptoms Bad quality images. No images available in your browser application. Note: AXIS 2420 User’s Manual Possible causes The Display Properties are incorrectly configured for your computer screen. Remedial actions Open the Display Properties for your screen and configure it to show at least 65000 colors, i.e. at least 16-bit. The camera is not focused correctly.
AXIS 2420 User’s Manual Other IP Setup Methods Appendix B - Other IP Setup Methods In addition to the ARP command (described earlier in the Installation section of this manual), you can alternatively set the IP address for your AXIS 2420 using any of the following methods - as appropriate for your operating system: Method Operating Systems Refer to... AXIS IP Installer Windows Using the AXIS IP Installer, on page 52.
Other IP Setup Methods AXIS 2420 User’s Manual Using the AXIS IP Installer AXIS IP Installer is a Windows program that is ideal for setting the IP addresses for multiple Axis networking products on your network. Also allowing you to access the home page of any Axis ThinServer device connected to your network, this freely distributed software is available for download from www.axis.com. Installing the AXIS IP Installer: 1.
AXIS 2420 User’s Manual Other IP Setup Methods Notes for Macintosh Users The AXIS 2420 supports TCP/IP over Ethernet, or PPP Modem dial-up. You must use TCP/IP on your Macintosh network, as there is no support for AppleTalk. When using the AXIS 2420 on a Macintosh, please observe the following points: • The camera has a default IP address of 192.36.253.80. • Assign a temporary IP address to a Mac workstation in the same subnet (e.g. 192.36.253.81) and then connect to the camera.
Lenses and Advanced Focusing AXIS 2420 User’s Manual Appendix C - Lenses and Advanced Focusing Your camera was supplied either without a lens (AXIS 2420), or with a DC-Iris lens (AXIS 2420 W/Lens). Either model can be fitted with any standard CS/C lens. The DC-Iris support included with the AXIS 2420 will drive any standard DC-Iris lens. Fitting a Lens Note: The AXIS 2420 is equipped with a CS-mount, so any standard CS lens can be fitted directly.
AXIS 2420 User’s Manual Lenses and Advanced Focusing Direct Focusing in Your Browser The AXIS 2420 is easily targeted for different applications. With your video stream displayed in a browser, simply adjust the camera focus ring until you are satisfied with the focus. Important! The illustration below is displayed as an example of a commonly available lens type, but is NOT typical for all lens types.
Lenses and Advanced Focusing AXIS 2420 User’s Manual Plane of Focus The lens has rotational focus control that allows the focal length of the lens to be adjusted manually. Depending on the chosen physical location for your camera, it is likely that several planes of focus will exist throughout the full focusing depth of the unit; consequently, the Status Indicator is likely to display green - indicating a good level of focus - several times throughout the full travel of the lens assembly.
AXIS 2420 User’s Manual Lenses and Advanced Focusing 5. Finally, turn the lens slowly towards the Far-focus (F, ∞) position, until the Status Indicator displays Green; that is, until a Good level of focus is achieved. Notes: •A Good level of focus is normally achievable throughout several planes within the focusing range of the camera. •The Status Indicator displays Green to indicate a Good level of focus at 80% of optimum focus.
Lenses and Advanced Focusing AXIS 2420 User’s Manual Exposure Control Overview The table below provides a summary of the Exposure Control settings in the Image Advanced page. Select the parameters for your lens type and product application. Lens Options Description DC-Iris The DC-Iris setting is the standard factory default setting found on the Image-Advanced page. It allows the user to manually specify the exposure, shutter speed, gain, and ALC levels.
AXIS 2420 User’s Manual Lenses and Advanced Focusing Adjusting the Back Focus Your AXIS 2420 is supplied with the back focus roughly set to accommodate a reasonable level of focus throughout the complete focusing range. However, if you are dissatisfied with the quality of focusing at a specific plane (or at several planes) within the focusing range, you may need to make some fine adjustments to the back focusing of the lens.
Customizing Your Camera AXIS 2420 User’s Manual Appendix D - Customizing Your Camera Modifying the File System The Linux-based operating system and flash memory file system make it possible for advanced users and application developers to customize the AXIS 2420 by adding additional files to the read-write area of the flash memory. Important! • Modification of the flash file system is NOT supported by Axis.
AXIS 2420 User’s Manual Customizing Your Camera Custom Web Pages The AXIS 2420 contains a re-writable flash memory file system that allows some directories and files to be changed by the root user, using FTP. This strictly non-supported product functionality makes it possible for advanced users and application developers to add their own Web pages, scripts, and other files to the Axis product.
Customizing Your Camera AXIS 2420 User’s Manual 4. Fetch the boa.conf file, by typing: get boa.conf 5. Edit boa.conf and add the following lines to the end of the file: Alias /index.html /etc/httpd/html/index.html Alias / /etc/httpd/html This will create an alias to your own "homemade" index.html file stored in the /etc/httpd/html/ directory and redirect access to it. Replace the edited boa.conf in the camera, by using the put command. 6. Restart the camera.
AXIS 2420 User’s Manual Updating the Firmware Appendix E - Updating the Firmware The AXIS 2420 camera firmware is stored in Flash memory. This memory is provided by a silicon chip that, just like any other ROM device, retains data content even after power is removed. Flash memory is unique because it allows its data to be erased and re-written. This means that you can install firmware updates for your AXIS 2420 as soon as they become available - without having to replace any parts.
The Unit Connectors AXIS 2420 User’s Manual Appendix F - The Unit Connectors This section provides an overview of the product connectors, namely: •1 x RS-232 Serial Connector •2 x I/O Connectors (I/O-A and I/O-B) •1 x DC-Iris Connector •1 x BNC Video Output •1 x Ethernet network connector (RJ-45) The RS-232 Serial Connector In the absence of a local network connection, a single 9-pin D-sub connector provides a dedicated physical interface for connecting a modem or computer to the AXIS 2420.
AXIS 2420 User’s Manual The Unit Connectors The I/O-A Connector Used for connecting external alarm devices and triggering images for alarm-based events, the 4-pole I/O-A Connector provides the interface for a single digital input. Connected to a switch or other external security device, an image is recorded every time the switch is activated. It also provides an auxiliary DC power input or output for the AXIS 2420. Pinout Information Pin Function 4 Digital Input - Photocoupled Cathode (-) As below.
The Unit Connectors AXIS 2420 User’s Manual The I/O-B Connector The 4-pole I/O-B connector provides a digital relay switch for the control of external surveillance devices and services; such as, lighting, annunciators, audible alarms, etc. It is also an RS-485/422 port for the control of pan tilt devices, etc. A pinout table is provided below. Pinout Information Pin Function 1 Relay switch - pole 1. Electrically isolated from chassis and connectors. 2 Relay switch - pole 2.
AXIS 2420 User’s Manual The Unit Connectors The DC-Iris Connector The AXIS 2420 can be used with any standard C/CS lens. With full support for standard DC-Iris lenses, the camera will automatically regulate the amount of light entering the camera. The DC-Iris Connector provides the power and control signalling required for a DC-Iris lens. The connector is located on the rear panel and the pinout for the connector is shown below.
The Unit Connectors AXIS 2420 User’s Manual This requires you to have root access to the AXIS 2420 and consequently, to supply a user name and password. Login as root and supply the root password (default = pass). Tip! Developers wishing to create applications incorporating sophisticated alarm conditioning using the relay output and digital input are encouraged to read the Camera API, HTTP-Interface Specification, available from the Axis Web at www.axis.com.
AXIS 2420 User’s Manual High-Speed Services Appendix G - High-Speed Services The AXIS 2420 is designed with high-speed Internet services foremost in mind, and you will experience the full performance of your AXIS 2420 if you are fortunate enough to have xDSL or a cable modem connection. However, as most high-speed Internet services only provide you with one external IP address, there are some practical issues that should be considered when developing your application.
Technical Specifications 70 AXIS 2420 User’s Manual Appendix H - Technical Specifications System Requirements - The AXIS 2420 uses the standard Internet TCP/IP suite of protocols and can be used with most operating systems: Windows, Linux, UNIX, Mac and several others. The only software required is Microsoft Internet Explorer 4.x/5.x or Netscape 4.x. Installation - Physical network connection using RJ-45 twisted pair cable, or remote connection using any standard serial modem.
AXIS 2420 User’s Manual Technical Specifications Metrics: - Height: 2.24” (57mm), Width: 3.39” (86mm), Length: 5.43” (138mm). Hardware - ARTPEC-1 compression chip; ETRAX-100LX (32-bit RISC, 100 MIPS CPU), 16 Mbytes DRAM, 4 Mbytes FLASH PROM. Lens (AXIS 2420 W/Lens only) - Varifocal DC Iris lens with CS Mount, manual zoom, variable focus, and exposure control. Variable shutter speeds between 1/50 - 1/10000 (PAL) and 1/60 -1/10000 (NTSC).
Physische Beschreibung AXIS 2420 User’s Manual Physische Beschreibung Machen Sie sich anhand der folgenden Informationen mit der AXIS 2420 vertraut, und beachten Sie insbesondere die Position der Anschlüsse und Anzeigen. Dieser Abschnitt enthält praktische Hinweise zur Installation des Produkts.
AXIS 2420 User’s Manual Physische Beschreibung 73 Bedienfeld hinten Netzteil-Anschluss PS-D-Stecker für den Anschluss an das AXIS 2420-Netzteil. Betriebsanzeige (PWR) Leuchtet normalerweise, wenn das Gerät an die Stromversorgung angeschlosssen ist. Leuchtet die Anzeige nicht oder blinkt sie, liegt ein Problem an der Kamera oder am externen Netzteil vor.
Überprüfen des Lieferumfangs AXIS 2420 User’s Manual Montage der AXIS 2420 Die AXIS 2420 wird ohne Befestigungsbaugruppe oder Ständer geliefert. Für die Befestigung der Kamera an der Baugruppe sind auf der oberen und unteren Gehäuseoberfläche Schraublöcher für die einfache Wand- oder Deckenmontage vorhanden. Das Schraubloch hat einen inneren Durchmesser von 1/4 Zoll UNC (Grobgewinde). Schraublöcher oben und unten.
AXIS 2420 User’s Manual Installieren in einem Netzwerk 75 Installieren in einem Netzwerk • Macintosh Anwender- bitte lesen Sie Notes for Macintosh Users auf Seite 53. • Einfach Installation mit dem AXIS IP Installer. Lesen Sie Using the AXIS IP Installer auf Seite 52. • Schnelle Installation - Befolgen Sie die nachfolgenden Anweisungen. ❶ Setzen Sie die gewünschle Linse in die AXIS 2420 ein. Die Linse raslet ein, indem Sie sie im Uhrzeigerfinn hineindrehen.
Installieren in einem Netzwerk AXIS 2420 User’s Manual ❺ Schließen Sie das externe Netzteil an die Einheit an, und verbinden Sie es mit Ihrem lokalen Stromnetz. ❻ Etwa 10-15 Sekunden nach dem Anschluss an das Stromnetz wird die Meldung "Reply from 172.21.1.200...“ (oder eine ähnliche Meldung) im DOS-Fenster angezeigt. Vergewissern Sie sich, dass die Betriebsanzeige konstant leuchtet und die Netzwerk-Anzeige in bestimmten Abständen blinkt. ❼ Verlassen Sie Ping.
AXIS 2420 User’s Manual Anschließen an ein Modem 77 Anschließen an ein Modem In diesem Abschnitt wird beschrieben, wie Sie die AXIS 2420 an ein serielles Modem anschließen, um Bilder über eine herkömmliche DFÜ-Verbindung zu übertragen. Wichtig! • • • Obwohl im Folgenden die Konfiguration des AXIS 2420 über ein Null-Modemkabel beschrieben wird, wird empfohlen (falls möglich), das Gerät zuerst über ein Ethernet-Netzwerk zu installieren und zu konfigurieren.
Anschließen an ein Modem AXIS 2420 User’s Manual Erstellen einer DFÜ-Netzwerkverbindung Führen Sie die folgenden Schritte aus, um eine DFÜ-Netzwerkverbindung zu Ihrer zu AXIS 2420 erstellen: ❶ Doppelklicken Sie auf Arbeitsplatz und anschließend auf das Symbol DFÜ-Netzwerk. ❷ Doppelklicken Sie auf das Symbol Neue Verbindung. ❸ Geben Sie einen Namen für die Verbindung ein (AxisCamera wird in den folgenden Beispielen als Name verwendet).
AXIS 2420 User’s Manual Anschließen an ein Modem 79 Feinabstimmung der DFÜ-Netzwerkeigenschaften Nachdem Sie die DFÜ-Verbindung für Ihre AXIS 2420 erstellt haben, führen Sie die folgenden Schritte aus, um eine Feinabstimmung der Verbindungseigenschaften vorzunehmen: ❶ Klicken Sie im Dialogfeld “DFÜ-Netzwerk” mit der rechten Maustaste auf die DFÜ-Verbindung, die Sie zuvor für Ihren AXIS 2420 erstellt haben (AxisCamera ist die in den vorangehenden Beispielen erstellte Verbindung).
Scharfeinstellung der Kamera AXIS 2420 User’s Manual Überprüfen der Modemverbindung und Fertigstellen der Installation Nachdem die DFÜ-Verbindung mithilfe des oben beschriebenen Verfahrens aufgebaut wurde, können Sie die Integrität der Verbindung schnell und einfach überprüfen, indem Sie über einen Standard-Web-Browser, wie z. B. Netscape oder Internet Explorer, auf die AXIS 2420 zugreifen. Gehen Sie folgendermaßen vor: abc.
AXIS 2420 User’s Manual Werkseitige Standardeinstellungen 81 Werkseitige Standardeinstellungen Unter bestimmten Umständen kann es erforderlich sein, die werkseitigen Standardeinstellungen Ihrer AXIS 2420 wiederherzustellen. Klicken Sie dazu auf die entsprechende Schaltfläche in den Verwaltungsprogrammen, oder drücken Sie die Kontroll-Taste. Befolgen Sie die Anweisungen, um die werkseitigen Standardeinstellungen mithilfe der Kontroll-Taste wiederherzustellen: 1.
Description du Materiel AXIS 2420 User’s Manual Description du Materiel Lisez les informations ci-dessous pour vous familiariser avec la caméra AXIS 2420, en portant particulièrement attention à l’emplacement des connecteurs et des voyants. Ces informations constituent une référence utile lors de l’installation du produit.
AXIS 2420 User’s Manual Description du Materiel 83 Panneau arrière Connecteur d’alimentation Connecteur PS-D pour la connexion de l’alimentation de la caméra AXIS 2420. Connecteur réseau La caméra AXIS 2420 est conçue pour les réseaux Ethernet 10 Mbit/s et Fast Ethernet 100 Mbit/s et se connecte au réseau à l’aide d’un câble à paire torsadée de catégorie 5 (10baseT et 100baseTX), terminé par un connecteur RJ-45 standard.
Vérification de la liste du matériel AXIS 2420 User’s Manual Fixation de la caméra AXIS 2420 La caméra AXIS 2420 est livrée sans support de montage, ni pied. Des trous de vis permettant de fixer la caméra sont fournis à la fois sur les surfaces supérieures et inférieures de l’unité, pour une installation facile sur un mur ou encore au plafond. Ces trous se caractérisent par une dimension interne de ¼" UNC.
AXIS 2420 User’s Manual Installation sur un réseau 85 Installation sur un réseau • Macintosh - Veuillez vous référez à Notes for Macintosh Users à la page 53. • Installation simple - Utilisez l'AXIS IP Installer. Voir Using the AXIS IP Installer à la page 52. • Installation rapide - Utilisez le guide ci-dessous pour installer rapidement votre serveur AXIS 2420 dans un réseau Ethernet: ❶ Installez l'objectif de votre choix sur l'AXIS 2420.
Installation sur un réseau AXIS 2420 User’s Manual ❺ Connectez l’adaptateur secteur externe à l’unité et branchez-le sur une source de courant secteur. ❻ Approximativement 10 à 15 secondes après la connexion de l’alimentation, le message ’Reply from 172.21.1.200...’ ou similaire, est renvoyé dans la fenêtre DOS. Assurez-vous que le voyant d’alimentation est allumé et que le voyant réseau clignote par intermittence. Connecteur d’alimentation ❼ Appuyez sur Control-C pour sortir de la commande ping.
AXIS 2420 User’s Manual Installation par l’intermédiaire d’un 87 Installation par l’intermédiaire d’un modem Les informations de cette section expliquent comment connecter le serveur AXIS 2420 à un modem série en vue de transmettre des images sur une connexion d’accès réseau à distance normale.
Installation par l’intermédiaire d’un modem AXIS 2420 User’s Manual Création d’une connexion d’accès réseau à distance Suivez les étapes ci-dessous pour créer une connexion d’accès réseau à distance dédiée pour votre produit: ❶ Double-cliquez sur Poste de travail puis double-cliquez sur l’icône Accès réseau à distance. ❷ Double-cliquez sur l’icône Nouvelle connexion. ❸ Donnez un nom à la connexion (les exemples qui suivent utilisent le nom AxisCamera).
AXIS 2420 User’s Manual Installation par l’intermédiaire d’un 89 Paramétrage des propriétés de l’accès réseau à distance Une fois la connexion d’accès réseau à distance de votre serveur AXIS 2420 créée, suivez les étapes ci-dessous pour affiner les propriétés de la connexion : ❶ Dans la boîte de dialogue Accès réseau à distance, cliquez avec le bouton droit sur la connexion d’accès réseau à distance dédiée créée précédemment pour votre serveur AXIS 2420 (AxisCamera dans notre exemple).
Mise au point de votre caméra AXIS 2420 User’s Manual Vérification de la connexion modem Après avoir lancé votre connexion d’accès à distance, comme cela est décrit ci-dessus, vous pouvez rapidement vérifier l’intégrité de la connexion en accédant à votre serveur AXIS 2420 à partir d’un navigateur Web standard, tel que Netscape (4.x) ou Internet Explorer (4.x/5.x): abc.
AXIS 2420 User’s Manual Restauration des paramètres d’usine 91 Restauration des paramètres d’usine par défaut Dans certaines circonstances, il peut être nécessaire de restaurer les paramètres par défaut (Factory Default) de votre caméra AXIS 2420. Pour cela, cliquez sur le bouton approprié dans la fenêtre Administration Tools, ou appuyez sur le bouton Control. Suivez les instructions ci-dessous pour restaurer les valeurs d'usine par défaut des paramètres de votre caméra, en utilisant le bouton Control.
Descripción física AXIS 2420 User’s Manual Descripción física Lea la información siguiente para familiarizarse con la AXIS 2420, haciendo especial atención en el lugar en el que están situados los conectores e indicadores. Esta sección proporciona una útil referencia cuando se instala el producto. Panel frontal Indicador de estado Utilizado junto con el asistente de foco, este indicador multicolor puede utilizarse como ayuda de enfoque local (consulte Enfocando la cámara en la página 100).
AXIS 2420 User’s Manual Descripción física 93 Panel posterior Para información del pinout, consulte Appendix F - The Unit Connectors. Conector de fuente de alimentación Conector PS-D para conectar la fuente de alimentación de la AXIS 2420. Indicador de corriente Normalmente iluminado cuando se aplica corriente. Si no está encendido, o destella, hay un problema en la cámara o en la fuente de alimentación externa.
Comprobar el inventario de hardware AXIS 2420 User’s Manual Montar la AXIS 2420 La AXIS 2420 se suministra sin una base o ensamblaje de montaje. En las superficies superior e inferior de la unidad hay agujeros roscados para sujetar la cámara a un ensamblaje, para instalarla fácilmente en una pared o en un techo. El agujero roscado tienen una dimensión interna de 1/4" UNC. Agujeros roscados en la parte superior y en la base.
AXIS 2420 User’s Manual Instalación de la cámara a una red 95 Instalación de la cámara a una red • Si Usted utiliza Macintosh - Consulte Notes for Macintosh Users en la página 53. • Instalación sencilla - Utilize AXIS IP Installer. Consulte Using the AXIS IP Installer en la página 52. • Instalación rápida - Siga las instrucciones debajo para instalar la AXIS 2420 en una red Ethernet. ❶ Monte su lente preferida en la AXIS 2420. Fije su lente rotandola en dirección a favor del reloj.
Instalación de la cámara a una red AXIS 2420 User’s Manual ❺ Conecte la fuente de alimentación externa a la unidad y conéctela a la red local. ❻ Aproximadamente 10 o 15 segundos después de haber conectado la fuente de alimentación, elmensaje ‘Contestar desde 172.21.1.200...’ - o similar vuelve a aparecer en la ventana de DOS. Asegúrese de que el indicador de corriente está encendido de forma permanente y de que el indicador de red destella intermitentemente. ❼ Pulse Control-C para salir de ping.
AXIS 2420 User’s Manual Instalación de la cámara a un módem 97 Instalación de la cámara a un módem La información de esta sección describe cómo conectar la AXIS 2420 a un módem de serie para transmitir imágenes a través de una conexión con marcación directa normal. ¡Importante! • • • Aunque las instrucciones para configurar la AXIS 2420 usando un cable de módem nulo aparecen a continuación, se recomienda que (si es posible) la unidad se instale y configure inicialmente sobre una red Ethernet.
Instalación de la cámara a un módem AXIS 2420 User’s Manual Creación de un acceso telefónico a redes Siga los siguientes pasos para crear un acceso directo a redes dedicado a su producto: ❶ Haga doble clic en Mi PC y haga doble clic en el iconoIcono Acceso telefónico a redes. ❷ Haga doble clic en el icono Realizar conexión nueva. ❸ Dé un nombre a la conexión (AxisCamera es el nombre que se utiliza en los ejemplos siguientes).
AXIS 2420 User’s Manual Instalación de la cámara a un módem 99 Configuración de las propiedades de acceso telefónico a redes Una vez creada la conexión con marcación directa para su AXIS 2420, siga los siguientes pasos para configurar las propiedades de conexión: ❶ Desde el diálogo de acceso telefónico a redes, haga clic con el botón de la derecha en la conexión con marcación directa creada anteriormente para su cámara (AxisCamera era la conexión creada que se utilizó en los ejemplos anteriores).
Enfocando la cámara AXIS 2420 User’s Manual Verificando la conexión de módem Habiendo iniciado la conexión con marcación directa tal como se describe arriba, puede verificar rápidamente la integridad de la conexión accediendo a la AXIS 2420 usando un buscador de web estándar, como Netscape o Internet Explorer de la siguiente forma: abc.
AXIS 2420 User’s Manual Incluir los parámetros por defecto 101 Incluir los parámetros por defecto En algunas circunstancias, puede ser necesario volver a incluir los Parámetros de fábrica por defecto para su AXIS 2420. Esto se realiza haciendo clic en el botón adecuado en Herramientas de administración o pulsando el botón Control. Siga las siguientes instrucciones para volver a incluir los parámetros del producto de fábrica por defecto utilizando el botón Control: 1.
Index 102 Index A Access rights 23 Admin - access rights 23 Administration Tools 20 Advanced lens parameters 58 Anonymous user access 23 AppleTalk 53 Application Wizard 19 Applications 31 ARP 48 ARTPEC-1 7 Audio Configuration 41 AXIS IP Installer 51 B Back focus 59 BNC Video Output 67 Boa Web server 8 BOOTP 51 C CCD 9 CGI scripts 6 COM-Ports 25 Compression 7 Configuring your camera 18 Connecting PTZ Devices 27 Connectors 64 Control Button 9 Creating a Motion Detection Window 24 CS Mount Ring 9 D DC
AXIS 2420 User’s Manual Motion Detection 24 Mounting the unit 11 N Network Address Translation (NAT) 69 Network Connector 10 Network Indicator 10 Network installation 12 Null Modem Cable 14 O Other IP setup methods 51 P Pan/Tilt/Zoom devices 25, 27 Picture frequency 32 PING the IP Address 47 Plane of Focus 56 Power Indicator 10 Power indicator 44 Power supply connector 10 PPP 8 Preset positions 29 Problems 47 Proprietary ISP Dial-up Protocols 34 R Rear Panel 10 Relay output 68 Routers 69 RS-232 conn
