USER MANUAL AXIS P3384–V
About this Document This manual is intended for administrators and users of the AXIS P3384–V Fixed Dome Network Camera, and is applicable to firmware 5.4 and later. It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems may also be beneficial, for developing shell scripts and applications.
AXIS P3384–V Table of Contents Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessing the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Access from a Browser . . . . . . . . . . . . .
AXIS P3384–V Hardware Overview Hardware Overview 1 2 3 1 2 3 4 5 6 7 8 5 4 6 7 8 Product ID and Serial number (S/N) SD card slot Network connector (PoE) Audio out Network, Status and Power LED indicators Audio in I/O connector Control button Connectors For technical specifications, see page 54. Network connector - RJ-45 Ethernet connector. Supports Power over Ethernet (PoE). NOTICE The product shall be connected using a shielded network cable (STP).
AXIS P3384–V Hardware Overview • Connecting to AXIS Internet Dynamic DNS Service. See page 41. To connect, press and hold the button for about 3 seconds. • Resetting the product to factory default settings. See page 48. I/O terminal connector - Use in applications for e.g. motion detection, event triggering, time lapse recording and alarm notifications.
AXIS P3384–V Accessing the Product Accessing the Product To install the Axis product, refer to the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are Internet Explorer with Windows, Safari with Macintosh and Firefox with other operating systems. See Technical Specifications on page 54. To view streaming video in Internet Explorer, allow installation of AXIS Media Control (AMC) when prompted.
AXIS P3384–V Accessing the Product Access from the Internet Once connected, the Axis product is accessible on your local network (LAN). To access the product from the Internet you must configure your network router to allow incoming data traffic to the product. To do this, enable the NAT-traversal feature, which will attempt to automatically configure the router to allow access to the product. This is enabled from Setup > System Options > Network > TCP/IP Advanced.
AXIS P3384–V Accessing the Product Select the power line frequency (50 Hz or 60 Hz) used at the location of the Axis product. Selecting the wrong frequency may cause image flicker if the product is used in fluorescent light environments. When using 50 Hz, the maximum frame rate is limited to 25 fps. Note Power line frequency is different in different geographic regions. In the Americas, 60 Hz is usually used; most other parts of the world use 50 Hz.
AXIS P3384–V Accessing the Product AXIS Media Control viewer toolbar The AXIS Media Control viewer toolbar is available in Internet Explorer only. See AXIS Media Control (AMC) on page 11 for more information. The toolbar displays the following buttons: The Play button connects to the Axis product and starts playing a media stream. The Stop button stops the media stream. The Snapshot button takes a snapshot of the video image. The location where the image is saved can be specified in the AMC Control Panel.
AXIS P3384–V Accessing the Product Click the Ctrl panel button to open the PTZ control panel which provides additional PTZ controls. User-defined buttons can also appear in the Control panel. See Controls on page 27. To view a specific view area or preset position, select the view area or preset position from the Source list. Pan and Tilt bars – Use the arrows to pan and tilt the camera view, or click on a position on the bar to steer the camera view to that position.
AXIS P3384–V Media Streams Media Streams The Axis product provides several audio and video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, audio streams and to the list of available stream profiles. Other applications and clients can access video and audio streams directly, without going via the Live View page. How to Stream H.264 The video compression standard H.
AXIS P3384–V Media Streams The AMC Control Panel can be used to configure various video and audio settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control Panel is automatically installed on first use, after which it can be configured. Open the AMC Control Panel from: • Windows Control Panel (from the Start menu) • Alternatively, right-click the video image in Internet Explorer and click Settings.
AXIS P3384–V Media Streams Note • = IP addess • The Axis product supports QuickTime 6.5.1 and later. • QuickTime adds latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this.
AXIS P3384–V Setting Up the Product Setting Up the Product The Axis product can be configured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have access to all settings except System Options See also the online help . Basic Setup Basic Setup provides shortcuts to the settings that should be made before using the Axis product: 1.
AXIS P3384–V Video and Audio Video and Audio The video and audio settings can be used to optimize video and audio quality. You can configure the following: • Video stream settings. See page 15. • Stream profiles. See page 16. • Camera settings. See page 17. • View areas. See page 18. • Overlay image. See page 19. • Privacy mask. See page 20. • Focus and zoom. See page 20. • Audio settings. See page 21. • Audio clips. See page 22.
AXIS P3384–V Video and Audio • Resolution. Select the default resolution. • Compression. The compression level affects the image quality, bandwidth and file size of saved images; the lower the compression, the higher the image quality with higher bandwidth requirements and larger file sizes. • Rotate image. If required, the image can be rotated. • Mirror. If required, the image can be mirrored. • Maximum frame rate. To avoid bandwidth problems, the frame rate allowed to each viewer can be limited.
AXIS P3384–V Video and Audio Camera Settings The Video & Audio > Camera Settings page provides access to advanced image settings for the Axis product. Image Appearance Increasing the Color level increases the color saturation. The value 100 gives maximum color saturation. The value 0 gives a black and white image. The image Brightness can be adjusted in the range 0–100, where a higher value produces a brighter image. Increasing the Sharpness can increase bandwidth usage.
AXIS P3384–V Video and Audio Shutter & Gain The shutter and gain settings affect the amount of motion blur and noise in the image. To adapt to different lighting, available storage space and bandwidth, it is often necessary to prioritize either low motion blur or low noise. The Axis product allows using different prioritization in normal light and in low light. Shutter speed is related to the amount of time the shutter is opened and is measured in seconds (s).
AXIS P3384–V Video and Audio To add a new view area: 1. Go to Video & Audio > View Areas. 2. Click Add. 3. The new view area appears under Selected view area. Enter a descriptive name in the Name field. 4. Select an Aspect ratio and a Video stream resolution. 5. A new view area covers the whole image. Use the mouse to move and resize the view area. 6. Select Enable PTZ to enable digital PTZ for this view area. 7. Click Save to save the settings.
AXIS P3384–V Video and Audio 2. Click Browse and browse to the file. 3. Click Upload. 4. Select the image to use from the Use overlay image list. 5. Click Save. To display the overlay image: 1. Go to Video & Audio > Video Stream and select the Image tab. 2. Under Overlay Settings, select Include overlay image at the coordinates and enter the X and Y coordinates. 3. Click Save. For information about supported image formats, see the online help .
AXIS P3384–V Video and Audio 1. Click Open iris to open the iris to its maximum position. This gives the smallest depth of field and provides the best conditions for focusing. 2. Focus is set in the Focus window. Use the mouse to move and resize the focus window. 3. Set the zoom level using the slider and click Perform auto focus to focus the camera automatically. 4. Click in the Focus position bar to focus on a desired location. The buttons < and > move the focus position one step in either direction.
AXIS P3384–V Video and Audio Encoding - Select digital audio encoding format. • AAC requires a license for both encoding and decoding. AAC is the least complicated and most widely used codec. If achieving the best possible audio quality is a priority, AAC is the recommended codec to use. An AAC license is included in the Axis product. • G711 • G726 Sample rate - The number of times per second the sound is sampled.
AXIS P3384–V Live View Config Live View Config You can customize the Live View page and alter it to suit your requirements. It is possible to define the following features of the Live View page. • Stream Profile. See page 16. • Default Viewer for Browser. See page 23. • Viewer Settings. See page 24. • Action Buttons. These are the buttons described in Controls on the Live View Page on page 8 . • User Defined Links. See page 24. • Output Buttons. See page 24.
AXIS P3384–V Live View Config Browser Viewer Description Windows Internet Explorer AMC Recommended viewer in Internet Explorer (H.264/Motion JPEG). QuickTime H.264. Java applet A slower imaging alternative to AMC (Motion JPEG). Requires one of the following installed on the client: • JVM (J2SE) 1.4.2 or higher. • JRE (J2SE) 5.0 or higher. Still image Displays still images only. Click the Refresh button in your browser to view a new image.
AXIS P3384–V Live View Config - Active/Inactive displays two buttons, one or each action. To configure the active and inactive states, go to System Options > Ports & Devices > I/O Ports and set the port’s Normal state. For more information about I/O ports, see I/O Ports on page 46.
AXIS P3384–V PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) The PTZ menu is available if digital PTZ (pan, tilt and zoom) is enabled in the selected view area. For more information on view areas, see View Areas on page 18. Preset Positions A preset position is a predefined view that can be used to quickly steer the camera to a specific location. Preset positions can be accessed in several ways: • By selecting the preset from the Preset positions drop-down list in the Live View Page.
AXIS P3384–V PTZ (Pan Tilt Zoom) Guard Tour A guard tour displays the video stream from different preset positions, one-by-one, in a predetermined order or at random and for configurable time periods. The enabled guard tour will keep running after the user has logged off or closed the browser. To add a guard tour: 1. Go to PTZ > Guard Tour and click Add. 2. Enter a descriptive name. 3. Specify the pause length between runs. 4. Select an available preset position and click Apply. 5.
AXIS P3384–V Detectors Detectors Camera Tampering Camera Tampering can generate an alarm whenever the camera is repositioned, or when the lens is covered, sprayed or severely defocused. To send an alarm, for example an email, an action rule must be set up. To configure tampering: 1. Go to Detectors > Camera Tampering. 2. Set the Minimum duration, that is, the time that must elapse before an alarm is generated. This can help prevent false alarms for known conditions that affect the image. 3.
AXIS P3384–V Detectors Note Using the motion detection feature may decrease the product’s overall performance. Set Up Motion Detection Windows To set up a motion detection Include Window, follow these instructions: 1. Go to Detectors > Motion Detection. 2. Select a desired resolution for viewing while setting up Motion Detection from the View in list. 3. Select the Configure Included Windows option and click New. Select the new window in the list of windows and enter a descriptive name. 4.
AXIS P3384–V Detectors A large difference in luminance is required to trigger motion detection. Medium level (50%) Low level (0%) Even very small objects trigger motion detection. An object that appears in the window triggers motion detection only for a very short time before it is considered as non-moving. Only very bright objects on a dark background trigger motion detection.
AXIS P3384–V Applications Applications Third party applications can be uploaded to and installed on the Axis product. For information about available applications, downloads, trials and licenses, go to www.axis.com/applications To upload an application, go to Applications > Overview, click Browse to locate the file and then click Upload Package. Click on the uploaded application’s name to open the menu options Settings, License and About.
AXIS P3384–V Events Events The Axis product can be configured to perform actions when different events occur, for example, start a recording when motion is detected. The set of conditions that defines how and when the action is triggered is called an Action Rule. Available Action Rule triggers and conditions include: • Applications — use installed applications to trigger the rule, see Applications on page 31.
AXIS P3384–V Events • - System Initializing — trigger the rule when the product is being started. This can for example be used to send a notification when the product restarts. - Recurrence — trigger the rule periodically, see Recurrences on page 35. This can for example be used to upload an image every 5 minutes. - Use Schedule — trigger the rule according to the selected schedule, see Schedules on page 34. Time Available actions include: • IR light — activate/de-activate IR light.
AXIS P3384–V Events 8. Select Network Share from the Storage drop-down list. To add additional criteria, select the Additional conditions option and add additional triggers. To prevent an action from being triggered repeatedly, a Wait at least time can be set. Enter the time in hours, minutes and seconds, during which the trigger should be ignored before the action rule can be activated again. The recording Duration of some actions can be set to include time immediately before and after the event.
AXIS P3384–V Events 3. Click OK. To use the schedule in an Action Rule, select the schedule from the Schedule drop-down list in the Action Rule Setup page. Recurrences Recurrences are used to trigger Action Rules repeatedly, for example every 5 minutes or every hour. To set up a recurrence: 1. Go to Events > Recurrences and click Add. 2. Enter a descriptive name and recurrence pattern. 3. Click OK.
AXIS P3384–V Recordings Recordings The Axis product can be configured to record video continuously or according to an action rule: • To start a continuous recording, see page 36. • To set up action rules, see page 33. • To access recordings, see Recording List on page 36. • To configure camera controlled storage, see Storage on page 45. Recording List Recorded videos are listed on the Recordings > List page.
AXIS P3384–V Recordings Note If a new stream profile is selected while a recording is ongoing, the recording will be stopped and saved in the recording list and a new recording with the new stream profile will start. All previous continuous recordings will remain in the recording list until they are removed manually or through automatic removal of old recordings.
AXIS P3384–V System Options System Options Security Users User access control is enabled by default and can be configured under System Options > Security > Users. An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may access the Live View page.
AXIS P3384–V System Options IEEE 802.1X IEEE 802.1X is a standard for port-based Network Admission Control providing secure authentication of wired and wireless network devices. IEEE 802.1X is based on EAP (Extensible Authentication Protocol). To access a network protected by IEEE 802.1X, devices must authenticate themselves.
AXIS P3384–V System Options A Server/Client certificate can be self-signed or issued by a Certificate Authority (CA). A self-signed certificate offers limited protection and can be used before a CA-issued certificate has been obtained. To install a self-signed certificate: 1. Go to System Options > Security > Certificates. 2. Click Create self-signed certificate and provide the requested information. To create and install a CA-signed certificate: 1. Create a self-signed certificate as described above. 2.
AXIS P3384–V System Options Network Basic TCP/IP Settings The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one version must always be enabled. IPv4 Address Configuration By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.
AXIS P3384–V System Options Advanced TCP/IP Settings DNS Configuration DNS (Domain Name Service) provides the translation of host names to IP addresses. The DNS settings are configured under System Options > Network > TCP/IP > Advanced. Select Obtain DNS server address via DHCP to use the DNS settings provided by the DHCP server.
AXIS P3384–V System Options NAT traversal (port mapping) for IPv4 A network router allows devices on a private network (LAN) to share a single connection to the Internet. This is done by forwarding network traffic from the private network to the “outside”, that is, the Internet. Security on the private network (LAN) is increased since most routers are pre-configured to stop attempts to access the private network (LAN) from the public network (Internet).
AXIS P3384–V System Options QoS (Quality of Service) QoS (Quality of Service) guarantees a certain level of a specified resource to selected traffic on a network. A QoS-aware network prioritizes network traffic and provides a greater network reliability by controlling the amount of bandwidth an application may use. The QoS settings are configured under System Options > Network > QoS.
AXIS P3384–V System Options UPnPTM The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol. UPnPTM can be disabled under System Options > Network > UPnPTM. RTP/H.264 The RTP port range and multicast settings are configured under System Options > Network > RTP. The RTP port range defines the range of ports from which the video/audio ports are automatically selected.
AXIS P3384–V System Options If the card’s status shows as failed, click Check disk to see if the problem can be found and then try Repair. This option is only available for SD cards with ext4. For SD cards with vFAT, use a card reader or computer to troubleshoot the card. To avoid filling the card, it is recommended to remove recordings continuously. Under Recording Settings, select Remove recordings older than and select the number of days or weeks.
AXIS P3384–V System Options • the default router • the subnet mask • the system time • the IEEE 802.1X settings • the focus position Click Default to reset all settings, including the IP address, to the factory default values. This button should be used with caution. The Axis product can also be reset to factory default using the control button, see Reset to Factory Default Settings on page 48. To reset the optics to the factory default position, click Calibrate under Optics.
AXIS P3384–V System Options The log levels for the System Log and the Access Log are set under System Options > Support > Logs & Reports > Configuration. The Access Log can be configured to list all connections to the product (select Critical, Warnings & Info). If required, a different log level can be used when sending emails. Advanced Scripting Scripting allows experienced users to customize and use their own scripts.
AXIS P3384–V Troubleshooting Troubleshooting Checking the Firmware Firmware is software that determines the functionality of network devices. One of your first actions when troubleshooting a problem should be to check the current firmware version. The latest version may contain a correction that fixes your particular problem. The current firmware version in the Axis product is displayed in the page Setup > Basic Setup and in Setup > About.
AXIS P3384–V Troubleshooting ping -s 408 In Windows, type the following from a command/DOS prompt (this may require that you run the command prompt as an administrator): arp -s ping -l 408 -t 2. If the product does not reply in 30 seconds, restart it and wait for a reply. Press CTRL+C to stop Ping. 3. Open a browser and type in the product’s IP address. In the page that appears, use the Browse button to select the upgrade file to use.
AXIS P3384–V Troubleshooting The product is accessible locally but not externally Router configuration To configure your router to allow incoming data traffic to the Axis product, enable the NAT-traversal feature which will attempt to automatically configure the router to allow access to the Axis product, see NAT traversal (port mapping) for IPv4 on page 43. The router must support UPnPTM. Firewall protection Check the Internet firewall with your network administrator.
AXIS P3384–V Troubleshooting No images displayed on web page Problems with AXIS Media Control (Internet Explorer only) To enable the updating of video images in Internet Explorer, set the browser to allow ActiveX controls. Also, make sure that AXIS Media Control is installed on your computer. Installation of additional ActiveX component restricted or prohibited Configure the Axis product to use a Java applet for updating video images in Internet Explorer.
AXIS P3384–V Troubleshooting No audio Incorrect setup Check the sound card in the computer. Ensure that mute is not selected and that the volume settings are correct. No audio or very poor audio quality Check that Enable audio support is selected under Setup > System Options > Security > Audio Support. Check that the correct Audio Input source is selected under Setup > Video & Audio > Audio Settings. Poor audio quality CPU overloaded Reduce the number of listeners and viewers.
AXIS P3384–V Technical Specifications Technical Specifications Function/group Video Item Specifications Models AXIS P3384–V Image sensor Progressive scan RGB CMOS 1/3” (effective) Lens Varifocal, remote focus and zoom, IR corrected, P-Iris control, megapixel resolution 3-9 mm, 84° - 30° view (horizontal angle of view, F1.
AXIS P3384–V Technical Specifications Function/group Item Specifications Network Security Password protection, IP address filtering, HTTPS encryption*, IEEE 802.1X network access control*, digest authentication, user access log Supported protocols IPv4/v6, HTTP, HTTPS, SSL/TLS*, QoS Layer 3 DiffServ, FTP, CIFS/SMB, SMTP, Bonjour, UPnP™, SNMPv1/v2c/v3(MIB-II), DNS, DynDNS, NTP, RTSP, RTP, TCP, UDP, IGMP, RTCP, ICMP, DHCP, ARP, SOCKS, etc.
AXIS P3384–V Technical Specifications Function/group Item Specifications FCC:FCC Part 15, Subpart B, Class B demonstrated by compliance with EN 55022 (CISPR 22) Japan: VCCI-2008, Class B, ITE • C-tick AS/NZS CISPR 22, demonstrated by compliance with EN 55022 (CISPR 22) Canada: ICES-003 Canadian ICES-003, Class B digital, demonstrated by compliance with EN 55022 (CISPR 22) Korea: Emission: KN22, Immunity: KN24 Australia: AS/NZS CISPR 22 Environmental:IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-14, IEC 60068-
User Manual AXIS P3384–V © Axis Communications AB, 2012 Ver. M1.10 Date: June 2012 Part No.
