SHB210 Series ™ ™ Intel Core 2 Duo/ Core Duo ™ ® Core Solo/ Celeron M PICMG 1.
Disclaimers This manual has been carefully checked and believed to contain accurate information. AXIOMTEK Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use. AXIOMTEK does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. AXIOMTEK does not make any commitment to update the information in this manual.
ESD Precautions Computer boards have integrated circuits sensitive to static electricity. To prevent chipsets from electrostatic discharge damage, please take care of the following jobs with precautions: Do not remove boards or integrated circuits from their anti-static packaging until you are ready to install them. Before holding the board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. It discharges static electricity from your body.
Table of Contents Disclaimers ........................................................................................................... ii ESD Precautions ................................................................................................. iii Chapter 1 1.1 1.2 1.3 1.4 Introduction .................................................................................... 1 Specifications ................................................................................. 2 Utilities Supported .......
Chapter 5 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12 5.13 5.14 5.15 5.16 Award BIOS Utility........................................................................ 28 Entering Setup.............................................................................. 28 Control Keys ................................................................................. 29 Getting Help .................................................................................. 29 The Main Menu .............................
MEMO vi
SHB210 Socket M Half-Size SBC User’s Manual Chapter 1 Introduction The SHB210 PICMG 1.3 half-size Single Board Computer supports ® ™ ™ ™ ® Intel Core 2 Duo/Core Duo/Core Solo/Celeron M processors, ® at FSB 533/667 MHz. The board integrates chipsets Intel 945GME and ICH7M-DH that deliver outstanding system performance through high-bandwidth interfaces, multiple I/O functions for interactive applications and various embedded computing solutions.
SHB210 Socket M Half-Size SBC User’s Manual 1.
SHB210 Socket M Half-Size SBC User’s Manual z Ethernet The LAN1/LAN2 is 8111B Ethernet controller support 10/100/1000 Mb Dual PCI-Express LAN z Audio HD audio interface for audio converter kit AX93242 z Serial ATA Support Serial ATA/Serial ATA II Two Serial ATA channels for a total of two Serial ATA hard drives Maximum transfer rate could up to 300MB/sec z Hardware Monitoring Controller: Winbond W83627HG-AW Detection of CPU temperature, System temperature, Power failure and Fan speed
SHB210 Socket M Half-Size SBC User’s Manual 1.3 Block Diagram 1.
SHB210 Socket M Half-Size SBC User’s Manual Chapter 2 Jumpers and Connectors 2.
SHB210 Socket M Half-Size SBC User’s Manual 2.
SHB210 Socket M Half-Size SBC User’s Manual 2.3 Jumper Settings Proper jumer settings configure the SHB210 to meet your application purpose. 2.3.1 COM2 Mode Select Jumpers: JP2, JP3, JP4 These jumpers select the COM1 port’s communication mode to operate RS-232 or RS-422/485. Description COM1 Function Jumper Setting RS-232 (Default) JP2 JP3 JP4 RS-422 JP2 JP3 JP4 RS-485 JP2 JP3 JP4 2.3.2 Compact Flash Setting Jumper: JP6 Use this jumper to set Master/Slave Compact Flash interface.
SHB210 Socket M Half-Size SBC User’s Manual 2.3.3 Compact Flash Voltage Selection Jumper: JP8 This jumper is to select the voltage for Compact Flash interface. Description Function Jumper Setting 3.3V (Default) LCD Voltage Function JP8 5V Jumper Setting JP8 2.3.4 COM1 DCD and Voltage Selection Jumper: JP1 Jumper Description Jumper Setting COM1 DCD Normal & RI (Default) Voltage Selection 12V Description Jumper Setting JP1 5V JP1 JP1 DCD/5V RI/12V JP1 2.3.
SHB210 Socket M Half-Size SBC User’s Manual 2.4 Connectors Connectors connect this board with other parts of the system. Loose or improper connection might cause problems. Make sure all connectors are properly and firmly connected. Here is a summary table shows you all connectors on the board.
SHB210 Socket M Half-Size SBC User’s Manual 2.4.1 Front Panel Output Connector: CN1 2.4.2 Printer Port Connector: CN2 Print Port Connector This board has a multi-mode parallel port to support the following modes: 1. Standard Mode: IBM PC/XT, PC/AT and PS/2™ are compatible with bi-directional parallel port. 2. Enhanced Mode: Enhanced parallel port (EPP) is compatible with EPP 1.7 and EPP 1.9 (IEEE 1284 compliant). 3.
SHB210 Socket M Half-Size SBC User’s Manual CN2: Pin Assignment Table Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 Signal Strobe# Data 0 Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 Acknowledge # Busy Paper Empty # Print Select Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 Signal CN2 Auto Form Feed# Error # Initialize # Printer Select In # GND GND GND GND GND GND GND GND GND 2.4.3 EPIC Power Connector: CN4 Pin 1 3 5 7 9 Signal PSON# GND +3.
SHB210 Socket M Half-Size SBC User’s Manual 2.4.5 Serial Port Interface Connectors: COM1, COM2 The serial interface for the board consists of COM1 port support RS232/422/485(COM1) and COM2 (COM2) supports RS-232. Pin Signal Pin 1 Data Carrier Detect (DCD) 2 3 Receive Data (RXD) 4 5 Transmit Data (TXD) 6 7 Data Terminal Ready (DTR) 8 9 Ground (GND) 10 Signal COM1, COM2 Data Set Ready (DSR) Request to Send (RTS) Clear to Send (CTS) Ring Indicator (RI) NC 2.4.
SHB210 Socket M Half-Size SBC User’s Manual CN6 2.4.7 IDE Interface Connector: CN3 The board provided one IDE Port to support maximum up to two IDE devices.
SHB210 Socket M Half-Size SBC User’s Manual CN3 2.4.8 LVDS/LCD Connectors: CN14, CN16, CN21 There are several connectors to support CRT VGA and flat panel displays. CN14 is a standard 15-pin connector commonly used for the CRT VGA display, CN16 a Hirose DF20-40pin connector for the LVDS flat panel connection, and CN21 a Hirose DF13-7pin connector for inverter.
SHB210 Socket M Half-Size SBC User’s Manual Pin 35 Signal Pin Signal LVDSA_D2- 36 LVDSA_CLK- 37 LVDSA_D2+ 38 LVDSA_CLK+ 39 GND 40 GND CN16 Hirose DF13-7pin LCD Power Connector for Inverter: CN21 Pin 1 2 3 4 5 6 7 Signal CN21 12V 12V 5V ENAB GND GND GND Jumpers and Connectors 15
SHB210 Socket M Half-Size SBC User’s Manual CRT Connector: CN14 CN14 is a standard 15-pin pin DB15 connector commonly used for the CRT VGA display. Pin 1 Signal Red Pin 2 Signal Pin Green 3 Signal Blue 4 N/A 5 GND 6 AGND 7 AGND 8 AGND 9 N/A 10 GND 11 N/A 12 DDC DAT 13 Horizontal Sync 14 Vertical Sync 15 DDC CLK CN14 2.4.9 Ethernet Connectors: CN5, CN7 The RJ-45 connectors CN5 and CN7 are for Ethernet.
SHB210 Socket M Half-Size SBC User’s Manual 2.4.10 USB Connectors: CN10, CN11 These Universal Serial Bus (USB) connectors on this board are for installing versatile USB interface peripherals. These are 10-pin standard USB connectors. Pin Signal Pin 1 USB POWER 3 USB P05 USB P0+ 7 USB GND 9 GND CN10, CN11 Signal 2 USB POWER 4 6 8 10 USB P1USB P1+ USB GND GND 2.4.
SHB210 Socket M Half-Size SBC User’s Manual 2.4.12 Front Panel Connector Power LED Pins 1, 3, 5 connect the system power LED indicator to its respective switch on the case. Pin 1 is +, and pin 5 assigned to -. Pin 3 is defined as NC. External Speaker and Internal Buzzer Connector Pins 2, 4, 6, 8 can be connected to the case-mounted speaker unit or internal buzzer. Hareware Reset Pins 11 and 12 are designed for Hardware Reset.
SHB210 Socket M Half-Size SBC User’s Manual 2.4.13 External Mouse/Keyboard Connectors: CN9/CN13 The board provides a keyboard (CN13) and Mouse (CN9) interface with two 5-pin connectors. 2.4.14 Clock 1 Data 2 No Connection 3 GND 4 Power 5 SYSTEM FAN1/FAN2/FAN3 Connectors: You can connect the system cooling fan cable to FAN1/FAN2/FAN3 for system cooling fan power. 2.4.
SHB210 Socket M Half-Size SBC User’s Manual 2.4.16 Ethernet Connector 1 External Speed LED: CN23 Pin Signal 1 2 3 CN23 100, Low Active 3.3V Gigibit, Low Active 2.4.17 Ethernet Connector 2 External Act/Link LED: CN24 Pin 1 2 Signal CN24 3.3V Link active 2.4.18 Ethernet Connector 1 External Act/Link LED: CN22 Pin 1 2 Signal CN22 3.3V Link active 2.4.19 Audio Connector CN12 Pin Signal Pin Signal 1 SDOUT 2 +12V 3 BCLK 4 +5VSB 5 SDIN0 6 +3.
SHB210 Socket M Half-Size SBC User’s Manual Jumpers and Connectors 21
SHB210 Socket M Half-Size SBC User’s Manual Chapter 3 Hardware Installation ® Before installing the processor, please access Intel website for more detailed information http://www.intel.com . 3.1 Installing the Processor The Intel® Pentium® M Processor is available as a boxed processor for laptop computers in the micro-FCPGA form factor.
SHB210 Socket M Half-Size SBC User’s Manual 3. If the cooling solution prevents you from accessing the processor socket, you may need to remove it. Instructions on how to remove your cooling solution should be provided in the documentation that came with the system. 4. To un-install the current processor, use a screwdriver to disengage (open) the socket actuator, as shown in Figure 1 below. (The most commonly used sockets are Molex* or FoxConn* sockets, so they are used in the illustrations below.
SHB210 Socket M Half-Size SBC User’s Manual 3.2 Installing the Memory The board supports two 200-pin DDR2 SO-DIMM memory sockets with maximum memory capacity up to 4GB. Please follow steps below to install the memory modules: 1 2 Push down latches on each side of the SO-DIMM socket. Align the memory module with the socket that notches of memory module must match the socket keys for a correct intallation. Install the memory module into the socket and push it firmly down until it is fully seated.
SHB210 Socket M Half-Size SBC User’s Manual MEMO Hardware Installation 25
SHB210 Socket M Half-Size SBC User’s Manual Chapter 4 Hardware Description 4.1 Microprocessors ® ™ ™ ™ The SHB210 Series supports Intel Core 2 Duo/ Core Duo/Core ® solo, Celeron M processors, which make your system operated under ® Windows 2000/XP and Linux environments. The system performance depends on the microprocessor. Make sure all correct settings are arranged for your installed microprocessor to prevent the CPU from damages. 4.
SHB210 Socket M Half-Size SBC User’s Manual 4.4 I/O Port Address Map ® ™ ™ ™ ® The Intel Core 2 Duo/ Core Duo/Core Solo, Celeron M CPUs can communicate via I/O ports. There are total 1KB port addresses available for assignment to other devices via I/O expansion cards.
SHB210 Socket M Half-Size SBC User’s Manual Chapter 5 Award BIOS Utility The Phoenix-Award BIOS provides users with a built-in Setup program to modify basic system configuration. All configured parameters are stored in a battery-backed-up RAM (CMOS RAM) to save the Setup information whenever the power is turned off. 5.1 Entering Setup There are two ways to enter the Setup program.
SHB210 Socket M Half-Size SBC User’s Manual 5.
SHB210 Socket M Half-Size SBC User’s Manual 5.4 The Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu appears on the screen. In the Main Menu, there are several Setup functions and a couple of Exit options for your selection. Use arrow keys to select the Setup Page you intend to configure then press to accept or enter its sub-menu.
SHB210 Socket M Half-Size SBC User’s Manual 5.5 Standard CMOS Setup Menu The Standard CMOS Setup Menu displays basic information about your system. Use arrow keys to highlight each item, and use or key to select the value you want in each item. z Date The date format is , . Press to show the calendar. day month Date year z It is determined by the BIOS and read only, from Sunday to Saturday. It can be keyed with the numerical/ function key, from 1 to 31.
SHB210 Socket M Half-Size SBC User’s Manual z IDE Channel 0 Master/IDE Channel 0 Slave/IDE Channel 1 Master/IDE Channel 1 Slave These items identify the types of each IDE channel installed in the computer. There are 45 predefined types (Type 1 to Type 45) and 2 user’s definable types (Type User) for Enhanced IDE BIOS. Press /<+> or /<−> to select a numbered hard disk type, or directly type the number and press . Please be noted your drive’s specifications must match the drive table.
SHB210 Socket M Half-Size SBC User’s Manual z Halt On This item determines whether the system will halt or not, if an error is detected while powering up. No errors The system booting will halt on any errors detected. (default) All errors Whenever BIOS detects a non-fatal error, the system will stop and you will be prompted. All, But Keyboard The system booting will not stop for a keyboard error; it will stop for other errors.
SHB210 Socket M Half-Size SBC User’s Manual 5.6 Advanced BIOS Features This section allows you to configure and improve your system, to set up some system features according to your preference. z CPU Feature Scroll to this item and press to view the CPU Feature sub menu.
SHB210 Socket M Half-Size SBC User’s Manual Scroll to this item and press to view the sub menu to decide the disk boot priority. Press to return to the Advanced BIOS Features page. z Virus Warning This option flashes on the screen. During and after the system boot up, any attempt to write to the boot sector or partition table of the hard disk drive will halt the system with the following message. You can run an anti-virus program to locate the problem. The default setting is “Disabled”.
SHB210 Socket M Half-Size SBC User’s Manual NOTE: This function is only available with DOS and other operating systems that do not trap INT13. z CPU L1 & L2 Cache These two options speed up memory access. However, it depends on the CPU/chipset design. The default setting is “Enabled”. CPUs without built-in internal cache will not provide the “CPU Internal Cache” item on the menu.
SHB210 Socket M Half-Size SBC User’s Manual z Boot Up NumLock Status Set the the Num Lock status when the system is powered on. The default value is “On”. z Security Option This item allows you to limit access to the system and Setup, or just to Setup. The default value is “Setup”. System Setup If a wrong password is entered at the prompt, the system will not boot, the access to Setup will be denied, either.
SHB210 Socket M Half-Size SBC User’s Manual 5.7 Advanced Chipset Features This section contains completely optimized chipset’s features on the board that you are strongly recommended to leave all items on this page at their default values unless you are very familiar with the technical specifications of your system hardware. z PCI Express Port 1 ~ 6 There are several PCI Express Ports for your selection.
SHB210 Socket M Half-Size SBC User’s Manual z DVMT Mode DVMT (Dynamic Video Memory Technology) helps you select the video mode. z DVMT/Fixed Memory Size DVMT (Dynamic Video Memory Technology) allows you to select a maximum size of dynamic amount usage of the video memory. The system would configure the video memory dependent on your application. z Boot Display This item is for Intel define ADD card only. Press to return to the Main Menu page. 5.
SHB210 Socket M Half-Size SBC User’s Manual z OnChip IDE Device Scroll to this item and press to view the sub menu OnChip IDE Device. ¾ ¾ ¾ IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can support.
SHB210 Socket M Half-Size SBC User’s Manual ¾ ¾ Slave PIO and/or IDE Secondary Master/Slave PIO items on the menu. IDE Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 to 4 provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device.
SHB210 Socket M Half-Size SBC User’s Manual z Azalia Controller Enable it when HD audio kit AX92342 is used. z Onboard Device Scroll to this item and press to view the sub menu Onboard Device. ¾ ¾ ¾ USB Controller Enable this item if you are using the USB in the system. You should disable this item if a higher-level controller is added. USB 2.0 Controller Enable this item if you are using the EHCI (USB2.0) controller in the system.
SHB210 Socket M Half-Size SBC User’s Manual z Super IO Device Scroll to this item and press to view the sub menu Super IO Device. ¾ ¾ ¾ ¾ ¾ Onboard FDC Controller Select Enabled, if your system has a floppy disk controller (FDC) installed on the system board and you want to use it. If you install and-in FDC or the system has no floppy drive, select Disabled in this field. Options: Enabled and Disabled.
SHB210 Socket M Half-Size SBC User’s Manual ¾ ¾ ECP Mode Use DMA Select a DMA channel for the parallel port while using the ECP mode. PWRON After PWR-Fail This item enables your computer to automatically restart or return to its operating status. Press to return to the Integrated Peripherals page, and press it again to the Main Menu page. 5.9 Power Management Setup The Power Management Setup allows you to save energy of your system effectively.
SHB210 Socket M Half-Size SBC User’s Manual Standby mode in S1 (POS) or S3 (STR) fashion through the setting of this field. Options are: [S1 (POS)] The S1 sleep mode is a low power state. In this state, no system context is lost (CPU or chipset) and hardware maintains all system contexts.
SHB210 Socket M Half-Size SBC User’s Manual Disabled 1/2/4/6/8/10/2 0/30/40 Min/1 Hr The System will never enter the SUSPEND mode. It defines continuous idle time before the system entering the SUSPEND mode. If any item defined in (J) is enabled and active, the SUSPEND timer will be reloaded. z HDD Power Down If HDD activity is not detected for a specified length of time in this field, the hard disk drive will be powered down while other devices remain active.
SHB210 Socket M Half-Size SBC User’s Manual 5.10 PnP/PCI Configuration Setup This section describes the configuration of PCI (Personal Computer Interconnect) bus system, which allows I/O devices to operate at speeds close to the CPU speed while communicating with other important components. This section covers very technical items that only experienced users could change default settings. z Init Display First This item allows you to decide whether PCI Slot or AGP to be the first primary display card.
SHB210 Socket M Half-Size SBC User’s Manual value is “Manual”. z IRQ Resources When resources are controlled manually, assign each system interrupt to one of the following types in accordance with the type of devices using the interrupt: 1. Legacy ISA Devices compliant with the original PC AT bus specification, requiring a specific interrupt (such as IRQ4 for serial port 1). 2. PCI/ISA PnP Devices compliant with the Plug and Play standard, whether designed for PCI or ISA bus architecture.
SHB210 Socket M Half-Size SBC User’s Manual 5.11 PC Health Status This section supports hardware monitering that lets you monitor those parameters for critical voltages, temperatures and fan speed of the board. z Current CPU Temperature The current system CPU temperature will be automatically detected by the system. z Current SYSTEM Temperature Show you the current system1 temperature. z Current FAN1 Speed Show you the current system fan1 temperature.
SHB210 Socket M Half-Size SBC User’s Manual 5.12 Load Fail-Safe Defaults When you press on this item, a confirmation dialog box pops out to show you such a message: Please press “Y” to load default values that will be factory settings for accomplishing the optimal performance of system operations.
SHB210 Socket M Half-Size SBC User’s Manual 5.13 Load Optimized Defaults This option allows you to load your system configuration with default values. These default settings are optimized to enable high performance features. To load CMOS SRAM with SETUP default values, please enter “Y”. If not, please enter “N”. 5.14 Set Supervisor/User Password You can set a supervisor or user password, or both of them. The differences between them are: 1. 2.
SHB210 Socket M Half-Size SBC User’s Manual Type a maximum eight-character password, and press . This typed password will clear previously entered password from the CMOS memory. You will be asked to confirm this password. Type this password again and press . You may also press to abort this selection and not enter a password. To disable the password, just press when you are prompted to enter a password. A message will confirm the password is getting disabled.
SHB210 Socket M Half-Size SBC User’s Manual 5.15 Save & Exit Setup This section allows you to determine whether or not to accept your modifications. Type “Y” to quit the setup utility and save all changes into the CMOS memory. Type “N” to bring you back to the Setup utility. 5.16 Exit Without Saving Select this option to exit the Setup utility without saving changes you have made in this session. Type “Y”, and it will quit the Setup utility without saving your modifications.
SHB210 Socket M Half-Size SBC User’s Manual Chapter 6 Installation of Drivers The device drivers are located on the Product Information CD-ROM that comes with the SHB210 Series package. The auto-run function of drivers will guide you to install the utilities and device drivers under a Windows system. You can follow the onscreen instructions to install these devices: Chipset VGA LAN 6.1 Installing Chipset Driver 1. Run the SETUP.EXE program from the driver directory in your driver CD.
SHB210 Socket M Half-Size SBC User’s Manual ® 2. An Intel License Agreement appears to show you the important information. Click “Yes” to next step. 3. Please wait while running the following setup operations.
SHB210 Socket M Half-Size SBC User’s Manual 4. 56 Click “Finish” to complete the setup process.
SHB210 Socket M Half-Size SBC User’s Manual 5. 6.2 You will be asked to reboot your computer when the installation is completed. Please click “Yes, I want to restart my computer now” if you don’t need to install any other drivers. Otherwise, please click “No, I will restart my computer later”, and go on next step. Installing VGA Driver 1. Run the SETUP.EXE program from the driver directory in your driver CD. Click “Next” to next step.
SHB210 Socket M Half-Size SBC User’s Manual 58 ® 2. An Intel License Agreement appears to show you the important information. Click “Yes” to next step. 3. The message of Readme File Information appears to show you the system requirements and installation information. Please click “Next”.
SHB210 Socket M Half-Size SBC User’s Manual 4. Please wait while running the following setup operations. 5. When this message appears, please click “Next”.
SHB210 Socket M Half-Size SBC User’s Manual 6. You will be asked to reboot your computer when the installation is completed. Please click “Yes, I want to restart my computer now” if you don’t need to install any other drivers. Otherwise, please click “No, I will restart my computer later”, and click “Finish” to complete the installation.
SHB210 Socket M Half-Size SBC User’s Manual 6.3 Installing LAN Driver 1. Run the InstallShield Wizard for Ethernet from the driver directory in your driver CD. Click “Next” to next step. 2. Click “Install” to start the installation.
SHB210 Socket M Half-Size SBC User’s Manual 3. Please wait while running the following installation operation. 4. Click “Finish” to complete the installation. 2. When this message appears, please click “Next”.
SHB210 Socket M Half-Size SBC User’s Manual MEMO Installation of Drivers 63
SHB210 Socket M Half-Size SBC User’s Manual Appendix Watch Dog Timer Please follow the below WDT process for setup the WDT function.
SHB210 Socket M Half-Size SBC User’s Manual MEMO Watch Dog Timer 65
