MANO861 ® Intel LGA1155 Socket Supports ® 22nm / 32nm Intel CoreTM i7 / ® CoreTM i5 / CoreTM i3 / Pentium / ® Celeron Mini ITX Motherboard User’s Manual
Disclaimers This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use. Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. Axiomtek does not make any commitment to update the information in this manual.
ESD Precautions Computer boards have integrated circuits sensitive to static electricity. To prevent chipsets from electrostatic discharge damage, please take care of the following jobs with precautions: Do not remove boards or integrated circuits from their anti-static packaging until you are ready to install them. Before holding the board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. It discharges static electricity from your body.
Conventions Used in This Manual To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. Information to prevent injury to yourself when trying to complete a task. Warning Information to prevent damage to the components when trying to complete a task. Caution Instructions that you MUST follow to complete a task. Important Tips and additional information to help you complete a task.
Table of Contents Disclaimers ..................................................................................................... ii ESD Precautions ........................................................................................... iii Conventions Used in This Manual............................................................... iv Chapter 1 Introduction ............................................. 1 1.1 Features ...............................................................................
3.2 Central Processing Unit (CPU) ......................................................... 20 3.2.1 3.2.2 3.3 System Memory ................................................................................. 24 3.3.1 3.3.2 3.3.3 3.3.4 3.4 Installing the CPU ...................................................................................... 21 Installing the CPU Heatsink and Fan ........................................................ 23 Overview ......................................................
vii
MANO861 Mini ITX Board Chapter 1 Introduction ® ® The MANO861 supports latest Intel Desktop LGA1155 CPU-socket interface processor. Intel ® TM TM TM ® LGA1155 socket supports 22nm/32nm Intel Core i7 / Core i5 / Core i3 / Pentium / ® Celeron desktop CPU, which are built on 22nm/32nm technologies to provide smart performance and responsiveness on executing tasks. It combines the CPU and GPU to offer fantastic HD media and graphics, especially on 3D gaming experience.
MANO861 Mini ITX Board 1.2 Specifications CPU ® Intel ® Intel ® Intel ® Intel ® Intel ® Intel TM Core i7 processor. TM Core i7 processor. TM Core i5 processor. TM Core i3 processor. Pentium® processor. Celeron® processor. System Chipset ® Intel H61. DRAM Transfer Rate 1333/1066MHz. BIOS AMI 32Mb SPI ROM. System Memory Two 204-pin unbuffered DDR3 SO-DIMM sockets. Maximum up to 16GB DDR3 1333/1066MHz memory with two SO-DIMMs.
MANO861 Mini ITX Board Watchdog Timer 1~255 seconds; up to 256 levels. Power Management ACPI (Advanced Configuration and Power Interface). Form Factor Mini ITX form factor. All specifications and images are subject to change without notice. Note 1.
MANO861 Mini ITX Board This page is intentionally left blank.
MANO861 Mini ITX Board Chapter 2 Board and Pin Assignments 2.1 Board Layout 2.
MANO861 Mini ITX Board 2.3 Jumper Settings Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2 jumper pins to close. And remove jumper clip from 2 jumper pins to open. The following illustration shows how to set up jumper. Before applying power to MANO861 Series, please make sure all of the jumpers are in factory default position. Below you can find a summary table and onboard default settings.
MANO861 Mini ITX Board 2.3.1 Clear CMOS (JCMOS1) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which includes system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3.
MANO861 Mini ITX Board 2.3.4 SelectCOM Connector (SelectCOM) Select COM for RS-232/422/485.
MANO861 Mini ITX Board 2.4 Connectors Signals go to other parts of the system through connectors. Loose or improper connection might cause problems, please make sure all connectors are properly and firmly connected. Here is a summary table which shows all connectors on the hardware. Connector Description KBMS_USB USB 2.0, PS/2 Keyboard and Mouse Connector COM1~2 COM1 and COM2 Connector DVI DVI Port VGA1 VGA Port LAN1USB12 LAN1, USB 2.0 Port 1 and 2 LAN2USB34 LAN2, USB 2.
MANO861 Mini ITX Board 2.4.1 1. 2. 3. 4. 5. 6. Rear Panel Connectors PS/2 port (purple). This port is for a PS/2 keyboard and mouse. USB 2.0 ports 5 and 6. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. Serial connectors. These 9-pin COM1 and COM2 ports are for serial devices. VGA port. This 15-pin VGA port connects to a VGA monitor. DVI-D port. This 29-pin DVI-D port is for a DVI monitor. LAN (RJ-45) ports.
MANO861 Mini ITX Board System fan interface is available through SYS_FAN1, see table below. 1 Pin Signal 1 2 3 GND SYSFAN1_VCC(PWM) SYSFAN1_IO Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! DO NOT place jumper caps on the fan connectors. Caution 2.4.3 COM Connectors (COM34 and COM56) These connectors are for serial (COM) ports.
MANO861 Mini ITX Board 2.4.5 Front Panel Connector (F_PANEL1) This connector is for a chassis-mounted front panel. The functions are described as follows. Pin Signal 1 2 3 4 5 6 7 8 9 HDDLED+ POWERLED+HDDLEDPOWERLEDGND PWSWITCH RESET GND NC 1 ATX Power Button/Soft-off Button (Pin 6-8 PWRBT) This 2-pin connector is for the system power button. Pressing the power button turns the system on or puts the system in sleep or soft-off mode depending on the BIOS settings.
MANO861 Mini ITX Board 2.4.6 Power Connectors (EATXPWR and ATX12V) Both connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. Pin Signal Pin Signal EATXPWR 1 2 3 +3.3V +3.3V Ground 1 +5V 5 6 7 17 18 19 20 24 12 9 10 11 12 Ground +5V Ground PWRGD (Power Good) +5V (Standby) +12V +12V +3.3V +3.
MANO861 Mini ITX Board 2.4.7 Internal Audio Connector (FPAUD1) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC ‘97 (optional) audio standard. Connect one end of the front panel audio I/O module cable to this connector.
MANO861 Mini ITX Board 2.4.9 LCD Inverter Connector (JBKL) The connector is for the control of internal LVDS brightness. Pin Signal 1 2 3 4 5 +12V GND BL_EN BRIGHT1 +5V 2.4.10 1 Serial ATA Connectors (SATA1~SATA3) These connectors support SATA 2.0 and are for the Serial ATA signal cables for Serial ATA hard disk drives. Pin Signal 1 2 3 4 5 6 7 GND SATA_TXP2 SATA_TXN2 GND SATA_RXN2 SATA_RXP2 GND 2.4.11 SATA1, SATA2, SATA3 USB Connector (USB78) These connectors are for USB 2.0 ports.
MANO861 Mini ITX Board 2.4.12 SPI Connector (SPI1) Is a point-to-point interface standard, which allows network equipment designers to develop an array of next-generation multi-service switches and routers to support multi-service traffic with aggregate bandwidths up to OC-192 (10Gb/s) and beyond, enabling them to dramatically increase system performance. Pin Signal 1 2 3 4 5 6 7 +3V GND SPI_CS# SPI_CLK SPI_MISO SPI_MOSI SPI_HOLD# 2.4.
MANO861 Mini ITX Board 2.4.
MANO861 Mini ITX Board This page is intentionally left blank.
MANO861 Mini ITX Board Chapter 3 Hardware Installation Take note of the following precautions before you install motherboard components or change any motherboard settings. Caution 3.1 Unplug the power cord from the wall socket before touching any component. Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity.
MANO861 Mini ITX Board Place this side towards the rear of the chassis. 3.2 Central Processing Unit (CPU) ® The motherboard comes with a surface mount Intel LGA1155 socket supports 22nm/32nm ® ® ® Intel Core™ i7 / i5 / i3 / Pentium / Celeron processor in the LGA1155 package. Important Caution 20 ® Your boxed Intel Core™ i7/ i5/ i3 mobile processor package should come with installation instructions for the CPU, fan and heatsink assembly.
MANO861 Mini ITX Board 3.2.1 1. Installing the CPU Locate the CPU socket on the motherboard. Before installing the CPU, make sure that the socket box is facing towards you and the load lever is on your left. Caution 2. Separate CPU cooler and its base first with screw driver. 3. Assemble the CPU fan retention module.
MANO861 Mini ITX Board 4. Position the CPU over the socket, making sure that the gold triangle is the same side as CPU socket triangle. CPU socket triangle 5. Lock and unlock CPU. Caution 22 Gold triangle The CPU fits in only one correct orientation.
MANO861 Mini ITX Board 3.2.2 Installing the CPU Heatsink and Fan 1. 2. Place the heatsink base on the relative bottom of motherboard. Place the heatsink assembly on the top of the CPU, making sure that the four fasteners match the holes on the motherboard. 3. Screw tightly the four fasteners. 4. Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN. Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.
MANO861 Mini ITX Board 3.3 System Memory 3.3.1 Overview The motherboard comes with two 204-pin Double Data Rate 3 (DDR3) Small Outline Dual Inline Memory Modules (SO-DIMM) sockets. A DDR3 module has the same physical dimensions as a DDR SO-DIMM but has a 204-pin footprint compared to the 204-pin DDR2 DIMM. DDR3 DIMMs are notched differently to prevent installation on a DDR2 DIMM socket.
MANO861 Mini ITX Board 3.3.2 Memory Configurations You may install 1GB, 2GB, and 4GB non-ECC DDR3 SO-DIMMs into the SO-DIMM sockets using the memory configurations in this section. Important 3.3.3 IF you installed four 1GB memory modules, the system may detect less than 3GB of total memory because of address space allocation for other critical functions. This limitation applies to Windows XP 32-bit version operating system since it does not support PAE (Physical Address Extension) mode.
MANO861 Mini ITX Board 3. Firmly insert the SO-DIMM into the socket until the retaining clips snap back in place and the SO-DIMM is properly seated. Locked retaining clip Important Caution 3.3.4 1. 2. A DDR3 SO-DIMM is keyed with a notch so that it fits in only one direction. DO NOT force a SO-DIMM into a socket to avoid damaging the SO-DIMM. The DDR3 SO-DIMM sockets do not support DDR2 SO-DIMMs. DO NOT install DDR2 SO-DIMM to the DDR3 SO-DIMM socket.
MANO861 Mini ITX Board 3.4 Expansion Card In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. Warning 3.4.1 1. 2. 3. 4. 5. 6.
MANO861 Mini ITX Board 3.4.4 PCI-Express Mini Card Connector This motherboard supports one PCI-Express Mini Card connector. The following figure shows a Decode card installed on this connector.
MANO861 Mini ITX Board Chapter 4 Hardware Description 4.1 Microprocessors ® TM TM TM ® ® The MANO861 Series supports Intel Core i7 / Core i5 / Core i3 / Pentium / Celeron ® ® processors, which enable your system to operate under Windows XP, Windows 7 and Linux environments. The system performance depends on the microprocessor. Make sure all correct settings are arranged for your installed microprocessor to prevent the CPU from damages. 4.
MANO861 Mini ITX Board 4.4 I/O Port Address Map ® TM TM TM ® ® The Intel Core i7 / Core i5 / Core i3 / Pentium / Celeron processors communicate via I/O ports. Total 1KB port addresses are available for assigning to other devices via I/O expansion cards.
MANO861 Mini ITX Board Hardware Description 31
MANO861 Mini ITX Board 4.
MANO861 Mini ITX Board Hardware Description 33
MANO861 Mini ITX Board 34 Hardware Description
MANO861 Mini ITX Board 4.
MANO861 Mini ITX Board This page is intentionally left blank.
MANO861 Mini ITX Board Chapter 5 AMI BIOS Setup Utility The AMI UEFI BIOS provides users with a built-in setup program to modify basic system configuration. All configured parameters are stored in a flash chip to save the setup information whenever the power is turned off. This chapter provides users with detailed description about how to set up basic system configuration through the AMI BIOS setup utility. 5.1 Starting To enter the setup screens, follow the steps below: 1. 2.
MANO861 Mini ITX Board Hot Keys Description Left/Right The Left and Right keys allow you to select a setup screen. Up/Down The Up and Down keys allow you to select a setup screen or sub-screen. + Plus/Minus The Plus and Minus keys allow you to change the field value of a particular setup item. Tab The key allows you to select setup fields. F1 The key allows you to display the General Help screen. F2 The key allows you to Load Previous Values.
MANO861 Mini ITX Board 5.3 Main Menu When you first enter the setup utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. System Time/Date can be set up as described below. The Main BIOS setup screen is shown below. BIOS Information Display the auto-detected BIOS information. System Date/Time Use this option to change the system time and date. Highlight System Time or System Date using the keys.
MANO861 Mini ITX Board 5.4 Advanced Menu The Advanced menu also allows users to set configuration of the CPU and other system devices. You can select any of the items in the left frame of the screen to go to the sub menus: ► ► ► ► ► ► ► ► ► ► ACPI Settings CPU Configuration SATA Configuration PCH-FW Configuration USB Configuration Second Super IO Configuration Super IO Configuration H/W Monitor Option Rom Policy CPU PPM Configuration For items marked with “”, please press for more options.
MANO861 Mini ITX Board ACPI Settings You can use this screen to select options for the ACPI configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen. ACPI Sleep State Select the highest ACPI sleep state the system will enter when the suspend button is pressed. Configuration options are Suspend Disabled, S1 only (CPU Stop Clock), and S3 only (Suspend to RAM).
MANO861 Mini ITX Board CPU Configuration This screen shows the CPU information. Active Processor Cores Allow users to set how many processor cores should be active. Intel Virtualization Technology This item allows a hardware platform to run multiple operating systems separately and simultaneously, enabling one system to virtually function as several systems.
MANO861 Mini ITX Board SATA Configuration In this Configuration menu, you can see the currently installed hardware in the SATA ports. During system boot up, the BIOS automatically detects the presence of SATA devices. SATA Controller(s) Enable or disable SATA device. SATA Mode Selection Determine how SATA controller(s) operate. Operation mode options are: IDE Mode, AHCI Mode and RAID Mode.
MANO861 Mini ITX Board 44 PCH-FW Configuration This screen displays Management Engine (ME) Firmware information.
MANO861 Mini ITX Board USB Configuration You can use this screen to select options for the USB Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen. USB Devices Display all detected USB devices. Legacy USB Support Use this item to enable or disable support for USB device on legacy operating system. The default setting is Enabled. Auto option disables legacy support if no USB devices are connected.
MANO861 Mini ITX Board Second Super IO Configuration You can use this screen to select options for the Second Super IO Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen. For items marked with “”, please press for more options. Serial Port 3~6 Configuration Use these items to set parameters of serial port 3~6.
MANO861 Mini ITX Board Super IO Configuration You can use this screen to select options for the Super IO Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen. For items marked with “”, please press for more options. Serial Port 1~2 Configuration Use these items to set parameters of serial port 1~2. Parallel Port Configuration Use this item to set parameters of parallel port.
MANO861 Mini ITX Board H/W Monitor Use this screen for Smart Fan configuration and hardware health status monitoring. This screen displays the temperature of system and CPU, cooling fan speed in RPM and system voltages (VCORE, +12V, +5V, 5VSB, etc). Smart Fan This option allows users to configure Smart Fan function.
MANO861 Mini ITX Board Option Rom Policy Boot Option Filter This option controls what devices system can boot to. Launch PXE OpROM policy Enable or disable boot options for legacy network devices. Launch Storage OpROM policy Control the execution of UEFI and legacy storage OpROM.
MANO861 Mini ITX Board CPU PPM Configuration Use this screen for CPU PPM configuration. EIST ® Enable or disable Intel SpeedStep. When enabled, CPU speed is controlled by the operating system. When disabled, CPU runs at its default speed. Turbo Mode This item is for enabling or disabling turbo mode. When enabled, it allows processor cores to run faster than marked frequency under certain conditions. CPU C3 Report Enable or disable CPU C3 report to the operating system.
MANO861 Mini ITX Board 5.5 Chipset Menu The Chipset menu allows users to change the advanced chipset settings. You can select any of the items in the left frame of the screen to go to the sub menus: ► PCH-IO Configuration ► System Agent (SA) Configuration For items marked with “”, please press for more options.
MANO861 Mini ITX Board PCH-IO Configuration This screen allows users to set PCH parameters. USB Configuration USB configuration settings. PCH Azalia Configuration PCH Azalia device configuration settings. LAN1 Controller Enable or disable LAN1 controller. LAN2 Controller Enable or disable LAN2 controller. Mini-PCIe Speed Allow you to select mini PCI-Express speed. Restore AC Power Loss Set the system power status when power returns from a power failure situation.
MANO861 Mini ITX Board PCH USB Configuration EHCI1/EHCI2 Enable or disable the EHCI controller. USB Ports Per-Port Disable Control Enable or disable each USB port individually.
MANO861 Mini ITX Board PCH Azalia Configuration Azalia Control detection of the Azalia device. Configuration options are Disabled, Enabled and Auto.
MANO861 Mini ITX Board System Agent (SA) Configuration This screen shows System Agent information and provides function for specifying related parameters. For items marked with “”, please press for more options. VT-d ® Enable or disable Intel chipset virtualization technology for directed I/O. VT-d can help end users improve security and reliability of the systems and also improve performance of I/O devices in virtualized environment.
MANO861 Mini ITX Board Graphics Configuration Primary Display Allow you to select which graphics controller to use as the primary boot device. Internal Graphics Enable or disable IGD. DVMT Pre-Allocated Select DVMT pre-allocated memory size. DVMT Total Gfx Mem Select DVMT total memory size.
MANO861 Mini ITX Board NB PCIe Configuration PEG0 – Gen X Select PEG0 speed. PEG0 ASPM Control ASPM support for the PEG device. Enable PEG Enable or disable PEG always. Detect Non-Compliance Device Enable or disable the detection of a non-compliance PCI-Express device in PEG.
MANO861 Mini ITX Board 58 Memory Configuration This screen displays system memory information.
MANO861 Mini ITX Board 5.6 Boot Menu The Boot menu allows users to change boot options of the system. Setup Prompt Timeout Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting. Bootup NumLock State Use this item to select the power-on state for the keyboard NumLock. Quiet Boot Select to display either POST output messages or a splash screen during boot-up. Boot Option Priorities These are settings for boot priority.
MANO861 Mini ITX Board 5.7 Save & Exit Menu The Save & Exit menu allows users to load your system configuration with optimal or fail-safe default values. Save Changes and Exit When you have completed the system configuration changes, select this option to leave Setup and return to Main Menu. Select Save Changes and Exit from the Save & Exit menu and press . Select Yes to save changes and exit.
MANO861 Mini ITX Board Appendix A Watchdog Timer About Watchdog Timer Software stability is major issue in most application. Some embedded systems are not watched by human for 24 hours. It is usually too slow to wait for someone to reboot when computer hangs. The systems need to be able to reset automatically when things go wrong. The watchdog timer gives us solution. The watchdog timer is a counter that triggers a system reset when it counts down to zero from a preset value.
MANO861 Mini ITX Board Sample Program Assembly sample code : #define #define #define #define #define #define #define #define NCT6776F_CONFIG_INDEX NCT6776F_CONFIG_DATA NCT6776F_CONFIG_MODE_ENTER_VALUE NCT6776F_CONFIG_MODE_EXIT_VALUE NCT6776F_LDN_SEL_REGISTER NCT6776F_ACTIVATE_REGISTER NCT6776F_LDN_GPIO3 NCT6776F_LDN_WDT 0x2e 0x2f 0x87 0xAA 0x07 0x30 0x09 0x08 #ifdef Oem_NCT6776F_WDT_PRESENT #if Oem_NCT6776F_WDT_PRESENT UINT8 Data8=0; IoWrite8(NCT6776F_CONFIG_INDEX, NCT6776F_CONFIG_MODE_ENTER_VALUE); I
MANO861 Mini ITX Board Appendix B Digital I/O About Digital I/O The onboard digital I/O has 8 bits. Each bit can be set to function as input or output by software programming. In default, all pins are pulled high with +5V level (according to main power). The BIOS default settings are 4 inputs and 4 outputs where all of these pins are set to 1.
MANO861 Mini ITX Board IoWrite8(NCT6776F_CONFIG_INDEX,0x27); //CR27 bit6, bit7 need to set 1, GP70 to GP77 Data8 = IoRead8(NCT6776F_CONFIG_DATA) | 0xC0; IoWrite8 (NCT6776F_CONFIG_DATA , Data8); IoWrite8 (NCT6776F_CONFIG_INDEX , NCT6776F_LDN_SEL_REGISTER); IoWrite8 (NCT6776F_CONFIG_DATA , NCT6776F_LDN_GPIO3); IoWrite8 (NCT6776F_CONFIG_INDEX , NCT6776F_ACTIVATE_REGISTER); Data8=IoRead8(NCT6776F_CONFIG_DATA)|0x80;//Active GPIO7 IoWrite8 (NCT6776F_CONFIG_DATA , Data8); IoWrite8 (NCT6776F_CONFIG_INDEX , NCT6776F
