SZU 21-00 OPERATION INSTRUCTIONS SAT-Navi EN – Read and keep
Operation Instructions SZU 21-00 Safety Notes 2 Turn off the receiver or any used power supply before installing, to avoid shortcircuit. Installation and repairs to the equipment may only be carried out by technicians observing the current VDE guidelines. No liability will be assumed in the case of faulty installation and commissioning. Before opening the device, pull the mains cable or remove the power supply, otherwise there is a danger to life.
Operation Instructions SZU 21-00 Content 1 Common 4 1.1 Delivery 4 1.2 Description 5 2 Power supply 2.1.1 External power supply 2.1.2 Satellite receiver 2.1.3 Internal batteries 7 7 7 7 3 Operation 8 4 14.04.11 3.1 3.1.1 Main menu Short Circuit Protection 8 10 3.2 Light menu 10 3.3 Update menu 11 Technical specifications 14 4.1 List of tables 15 4.
Operation Instructions SZU 21-00 Chapter 1: Common 1 Common 1.1 Delivery Fig.
Operation Instructions SZU 21-00 Chapter 1: Common 1.2 Description This product is simple and convenient for setting and aligning a satellite dish. Using the satellite parameters the user can set and align a satellite dish quickly, accurately and easily. DC-power supply socket LNB Multiswitch SAT-Receiver ext. power supply Fig. 2: Inputs, display, buttons Inputs, display, buttons 1.
Operation Instructions SZU 21-00 Chapter 1: Common 5. Buttons ( , , OK) To navigate in the software menu 6. LC- Display Shows menu and additional information. 7. LNB input Satellite signal input port - connect directly to the LNB. 8. DC power supply input The SAT-Navi can be supplied by a connected power supply (SZU 99-22) or satellite receiver using this F-socket. At the bottom side 9 10 8 7 Fig. 3: Battery compartment 9.
Operation Instructions SZU 21-00 Chapter 2: Power supply 2 Power supply There are three ways to establish the power supply of the device: 2.1.1 External power supply Connect the external power supply to the DC-power supply socket (1). Make sure the slide switch (2) is in the position (“EXT”). Fig. 4: DC-power supply socket (1),slide switch (2) 2.1.
Operation Instructions SZU 21-00 Chapter 3: Operation Low Voltage If the voltage of any power source is lower than 13.3V, the red low voltage LED lights up Take care, that the input voltage is always higher than 13.3V. If you are using rechargeable batteries, switch off (to “EXT”) the device when the red LED lights up to prevent the cells from total discharge. 3 Operation 3.1 Main menu At power on, the display shows version information of the software, and then appears the main menu. Fig.
Operation Instructions SZU 21-00 Chapter 3: Operation SAT-Navi menu To align a satellite dish, please take the following steps: 1. Select a satellite from the list Fig. 6: SAT-Nav menu 2. Choose if you want to search the satellite with the default transponder (FREQ. DEFAULT) or with other transponders (FREQ. LIST). Please prefer (FREQ. DEFAULT), because the identification of the satellite is more precise for this option. Fig. 7: Transponder Î If you choose (FREQ.
Operation Instructions SZU 21-00 Chapter 3: Operation 3. Please move now the Satellite dish antenna slowly until you clearly hear the buzzer noise. The SAT Navi has logged-in and reckognized the wanted Satellite. The following other informations are displayed now too: P: Signal Strength (in dBµV) BER: Bit Error Rate Q: Signal Quality (Bar Graph) Fig. 9: Signal With this Information and the acoustic signal, you can fine-tune the antenna to the optimal position.
Operation Instructions SZU 21-00 Chapter 3: Operation 3.3 Update menu For always being up to date, there is a possibility to update the software of the Satellite Navigator by a serial (RS-232) interface. Since most modern PCs don’t have a RS-232 port any more, an adapter to USB has to be used. To update the software, please do the following steps: 1. Connect the update adapter to the Satellite Navigator at the connector found in the battery compartment (see picture).. RS-232Adapter Fig.
Operation Instructions SZU 21-00 Chapter 3: Operation Fig. 11: Null modem cable and USB adapter 3. Connect the USB adapter to your PC. 4. Start the software update application on your PC and choose the right COM-Port. If you are not sure, which COM-Port to choose, under Windows you can find out the right port in the device manager. 5. Press “Send” on the update tool. 6. Power on the Satellite Navigator and choose “Update” from the main menu.
Operation Instructions SZU 21-00 Chapter 3: Operation Fig. 13: Update cancelled There will also be the message “The STB is up to date!” in that case. 14.04.
Operation Instructions SZU 21-00 Chapter 4: Technical specifications 4 Technical specifications Frequency range RF connecters Operating voltage Current consumption Tab. 1: Data sheet 14 950…2150 MHz F female 13...19 VDC 300mA © AXING AG • Reserving change in design and type - We cannot be held liable for printing errors 14.04.
Operation Instructions SZU 21-00 Chapter 4: Technical specifications 4.1 Tab. 1: 4.2 List of tables Data sheet 14 List of illustrations Fig. 1: Fig. 2: Fig. 3: Fig. 4: Fig. 5: Fig. 6: Fig. 7: Fig. 8: Fig. 9: Fig. 10: Fig. 11: Fig. 12: Fig. 13: Delivery Inputs, display, buttons Battery compartment DC-power supply socket (1),slide switch (2) Main menu SAT-Nav menu Transponder Searching of a signal Signal RS-232-Adapter Null modem cable and USB adapter Time out Update cancelled 14.04.
Operation Instructions SZU 21-00 Chapter 4: Technical specifications 16 © AXING AG • Reserving change in design and type - We cannot be held liable for printing errors 14.04.
