Instructions

2020-06-30 | Technical improvements, changes in design, printing- and other errors expected. 13
4. Configuration
4.1. Basic setting for the reception of a satellite
In the basic setting, the Unicable II output functions in the dynamic mode (compatible with EN50494/EN50607)
and provides 32 user bands. This enables the connection of up to 32 receivers. Each receiver must be assigned
to one of the 32 user bands.
The standard frequencies, supported protocols and PINs of the user bands (basic setting, bandwidth 30 MHz):
UB1: 1280 MHz (EN50494+EN50607, PIN=1)
UB2: 1382 MHz (EN50494+EN50607, PIN=2)
UB3: 1484 MHz (EN50494+EN50607, PIN=3)
UB4: 1586 MHz (EN50494+EN50607, PIN=4)
UB5: 1688 MHz (EN50494+EN50607, PIN=5)
UB6: 1790 MHz (EN50494+EN50607, PIN=6)
UB7: 1892 MHz (EN50494+EN50607, PIN=7)
UB8: 1994 MHz (EN50494+EN50607, PIN=8)
UB9: 974 MHz (EN50607, PIN=9)
UB10: 1008 MHz (EN50607, PIN=10)
UB11: 1042 MHz (EN50607, PIN=11)
UB12: 1076 MHz (EN50607, PIN=12)
UB13: 1110 MHz (EN50607, PIN=13)
UB14: 1144 MHz (EN50607, PIN=14)
UB15: 1178 MHz (EN50607, PIN=15)
UB16: 1212 MHz (EN50607, PIN=16)
UB17: 1246 MHz (EN50607, PIN=17)
UB18: 1314 MHz (EN50607, PIN=18)
UB19: 1348 MHz (EN50607, PIN=19)
UB20: 1416 MHz (EN50607, PIN=20)
UB21: 1450 MHz (EN50607, PIN=21)
UB22: 1518 MHz (EN50607, PIN=22)
UB23: 1552 MHz (EN50607, PIN=23)
UB24: 1620 MHz (EN50607, PIN=24)
UB25: 1654 MHz (EN50607, PIN=25)
UB26: 1722 MHz (EN50607, PIN=26)
UB27: 1756 MHz (EN50607, PIN=27)
UB28: 1824 MHz (EN50607, PIN=28)
UB29: 1858 MHz (EN50607, PIN=29)
UB30: 1926 MHz (EN50607, PIN=30)
UB31: 1960 MHz (EN50607, PIN=31)
UB32: 2028 MHz (EN50607, PIN=32)
If you use programmable antenna sockets SSD 6-xx, you must program the corresponding user bands at
these sockets. We recommend you to note the user bands assigned to the antenna sockets. Use, for
example the marking label of the AXING SSD 6-xx single cable antenna sockets.
Use the highest frequency for the antenna socket with the shortest cable route to the multiswitch and the
lowest frequency for the antenna socket with the longest cable route to the multiswitch.
If you use less than 32 receivers, use the lowest frequencies.
Assign the corresponding user bands programmed on the antenna socket to the connected receivers.
4.2. Changing the basic settings
The basic configuration of the multiswitch can be changed by means of the SZU 55-00 programmer ( available
as an accessory). The PC software can be downloaded at www.axing.com | Download.
Note: The software includes an online help (starts with key F1). In this help you will find a detailed description
of all programming steps. The SES 5532-19 is called ODU (Out-Door-Unit) in this online help.