Datasheet

Anhang
Annex
Stand: März 2010 – Konstruktions- und Typenänderung vorbehalten
state of the art: March 2010 – Reserving change in design and type
Seite 195
Page 195
4.5.4 Pegelumrechnung
Pegel (dBµV) / in Spannung (mV)
4.6 EMV Anforderungen
(EMV - Elektromagnetische Verträglichkeit)
4.6.1 Störstrahlleistung
Grenzwerte laut EN 50083 - 2
für die Störstrahlleistung:
Diese Grenzwerte dürfen aktive Komponenten bei dem angegebenen
max. Ausgangspegel nicht überschreiten.
4.6.2 Schirmungsmaß
Anhand der Grenzwerte der Störstrahlleistung lässt sich das
erforderliche Schirmungsmaß der aktiven Geräte berechnen, bzw. bei
bekanntem Schirmungsmaß hieraus der maximal zulässige
Betriebspegel.
Max. Betriebspegel (dBµV) =
Grenzwertpegel an 75 Ohm (dBµV) + Schirmungsmaß (dB)
Schirmungsmaß (dB) =
Max. Betriebspegel (dBµV) –39 dBµV
4.6.3 Klassifizierung
Mit der Einführung der Ergänzung 1 zur EN 50083 - 2 wurden für pas-
sive Geräte zusätzlich zu den bisherigen Grenzwerten des Mindest-
schirmungsmaßes erhöhte Werte festgelegt. Diese Geräte sind
einzusetzen, wenn am Installationsort erhöhte Feldstärken zu erwart-
en sind.
Pegel (dBµV)
Level (dBµV)
0123456789
40 0,10 0,11 0,13 0,14 0,16 0,18 0,20 0,22 0,25 0,28
50 0,32 0,36 0,40 0,45 0,50 0,56 0,63 0,71 0,79 0,89
60 1 1,1 1,3 1,4 1,6 1,8 2 2,2 2,5 2,8
70 3,23,644,555,66789
80 10 11 13 14 16 18 20 22 25 28
90 32 36 40 45 50 56 63 71 79 89
100 100 112 126 141 158 178 200 224 251 281
110 316 355 398 447 501 562 631 708 794 891
120 1000 1122 1259 1413 1585 1778 2000 2239 2512 2818
Frequenzbereich
(MHz)
Grenzwert (dBpW)
Grenzwertpegel
an 75 Ohm (dBµV)
5 - 30 in Beratung -
30 - 1000 20 39
1000 - 2500 43 62
2500 - 25 GHZ 57 76
Klassifizierung nach EN 50083-2
(Geräte und Bauteile)
Frequenzbereich (MHz) Grenzwert (dB)
Klasse A Klasse B
30 - 300 85 75
300 - 470 80 75
470 - 1000 75 65
1000 - 3000 55 55
Klassifizierung nach EN 50117 - 2/A1
(koaxiale Leitungen)
Frequenzbereich (MHz) Grenzwert (dB)
Klasse A Klasse B
5 - 30 (Rückkanal) 5 mOhm/m <15 mOhm/m
30 - 300 85 75
300 - 470 85 75
470 - 1000 85 75
1000 - 2000 75 65
2000 - 3000 65 55
4.5.4 Level conversion
Level (dBµV) / in voltage (mV)
4.6 EMC requirements
(EMC - Electromagnetic compatibility)
4.6.1 Interference radiation output
Limit values according to EN 50083 - 2
for interference radiation output
Active components may not exceed these limit values at the indicated
maximum output level.
4.6.2 Screening
Based on the limit value of the interference radiation output the
required screening of the active devices can be calculated, or with
known screening the admissible maximum operating level.
Max. operating level (dBµV) =
limit value at 75 Ohm (dBµV) + screening (dB)
screening (dB) =
max. operating level (dBµV) –39 dBµV
4.6.3 Classification
With the introduction of amendment 1 for EN 50083 - 2 increased
values were defined for passive devices in addition to the current limit
values of the minimum screening. These devices have to be used
when an increased field strength has to be expected at the installation
site.
0
0,10
0,32
1
3,2
10
32
100
316
1000
Frequency range
(MHz)
Limit value (dBpW)
Limit level
at 75 Ohm (dBµV)
5 - 30 in consideration -
30 - 1000 20 39
1000 - 2500 43 62
2500 - 25 GHZ 57 76
Classification according to EN 50083-2
(devices and components)
Frequency range (MHz) Limit value (dB)
Class A Class B
30 – 300 85 75
300 – 470 80 75
470 - 1000 75 65
1000 - 3000 55 55
Classification according to EN 50117 - 2/A1
(coax. cable)
Frequency range (MHz) Limit value (dB)
Class A Class B
5 - 30 (return path)) 5 mOhm/m <15 mOhm/m
30 - 300 85 75
300 - 470 85 75
470 - 1000 85 75
1000 - 2000 75 65
2000 - 3000 65 55