AXI00004 INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’UTILISATION MANUALE DI ISTRUZIONI
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com or towerhobbies.com and click on the support tab for this product.
EN TABLE OF CONTENTS Water-resistant Vehicle with Waterproof Electronics ....... 3 Box Contents ....................................................................... 4 USB Charging Warnings ..................................................... 5 Charge the Vehicle Battery ................................................. 5 Transmitter Layout .............................................................. 6 Install the Transmitter Batteries .........................................
EN WET CONDITIONS MAINTENANCE • Drain any water that has collected in the tires by spinning them at high speed. With the body removed, place the vehicle upside down and pull full throttle for a few short bursts until the water has been removed. CAUTION: Always keep hands, fingers, tools and any loose or hanging objects away from rotating parts when performing the above drying technique. • Remove the battery pack(s) and dry the contacts.
EN USB CHARGING WARNINGS WARNING: Failure to exercise caution while using this product and comply with the following warnings could result in product malfunction, electrical issues, excessive heat, FIRE, and ultimately injury and property damage. • NEVER LEAVE CHARGING BATTERIES UNATTENDED. • NEVER CHARGE BATTERIES OVERNIGHT. • Never attempt to charge dead, damaged or wet battery packs. • Never attempt to charge a battery pack containing different types of batteries.
EN TRANSMITTER LAYOUT Use the diagram below to familiarize yourself with the different parts of your transmitter. The transmitter antenna is mounted internally and is located in the front portion of the transmitter. When you are driving your model, hold the transmitter so it is oriented as close to vertical as possible. Do not try to follow your model with the transmitter. This provides the best RF signal between the transmitter and the receiver.
EN INSTALL THE TRANSMITTER BATTERIES 1. Press the battery compartment latch and rotate the batter cover to open. 2. Install 4 AA alkaline batteries (or Ni-Cd or Ni-MH), verifying correct polarity. 3. Close the battery cover until it latches. CAUTION: NEVER remove the transmitter batteries while the vehicle is powered ON. Loss of vehicle control, damage, or injury may occur. CAUTION: If using rechargeable batteries, charge only rechargeable batteries.
EN INSTALL THE VEHICLE BATTERY POWER ON THE TRANSMITTER 8
EN POWER ON THE VEHICLE TEST THE CONTROLS With the vehicle wheels off the ground, test the throttle and steering controls. Ensure the wheels spin in the proper direction and the front wheels turn in the proper direction with steering input. After checking for proper direction of controls, start driving slowly. If the vehicle does not go straight without steering input, adjust the steering trim dial on the transmitter until the vehicle holds a straight line with no steering input..
EN AFTER DRIVING When you are finished driving your vehicle: 1. Power off the vehicle. 2. Power off the transmitter. 3. Remove the vehicle battery and charge if necessary. BINDING THE TRANSMITTER AND RECEIVER Binding is the process of programming the receiver to recognize a specific transmitter signal, thus preventing interference from other transmitters. The transmitter and receiver included with your vehicle are bound at the factory. If you need to rebind, follow the instructions below.
EN TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Batteries are not installed properly in the transmitter Weak or no battery in the vehicle Vehicle does not move Damaged motor Frayed or broken wiring ESC is shut down by heat protection circuit Improper antenna placement Loss of vehicle control Steering and/or throttle function is reversed Weak or no batteries in the transmitter or vehicle Neutral or trim position is incorrect Receiver and/or battery not connected properly Servo travel is reversed at
EN Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
EN WARRANTY AND SERVICE CONTACT INFORMATION Country of Purchase Horizon Hobby Contact Information Horizon Service Center servicecenter.horizonhobby.com/RequestForm/ (Repairs and Repair Requests) productsupport@horizonhobby.com United States Horizon Product Support (Product Technical Assistance) 877-504-0233 of America websales@horizonhobby.com Sales 800-338-4639 European Union Horizon Technischer Service service@horizonhobby.
EN COMPLIANCE INFORMATION FOR THE EUROPEAN UNION EU Compliance Statement: Axial SCX24 B17 Betty 1/24 Scale Electric 4WD RTR (AXI00004) Hereby, Horizon Hobby, LLC declares that Wireless Frequency Range and Wireless Output Power: the device is in compliance with the following: EU Radio 2405.0 – 2450.0 MHz Equipment Directive 2014/53/EU. 19dBm The full text of the EU declaration of conformity is Manufacturer: available at the following internet address: https://www. Horizon Hobby, LLC horizonhobby.
EN EXPLODED VIEWS // EXPLOSIONSZEICHNUNGEN // VUES ÉCLATÉES // VISTE ESPLOSE AXI31612 SCX24 Shock Set (assembled) SCX24 Stoßdämpfersatz (montiert) Ensemble d’amortisseurs SCX24 (assemblés) SCX24 Set ammortizzatori (assemblati) AXI31611 SCX24 Driveshaft Set (short, medium, long) SCX24 Antriebswellensatz (kurz, mittel, lang) Ensemble d’arbre de transmission SCX24 (court, moyen, long) SCX24 Set albero di trasmissione (corto, medio, lungo) AXI31608 SCX24 Transmission (assembled) SCX24 Getriebe (montiert) Tra
AXI31610 SCX24 Rear Axle (assembled) SCX24 Hinterachse (montiert) Essieu arrière SCX24 (assemblé) SCX24 Assale posteriore (assemblato) AXI31609 SCX24 Front Axle (assembled) SCX24 Vorderachse (montiert) Essieu avant SCX24 (assemblé) SCX24 Assale anteriore (assemblato) 52
EN AXI31613 SCX24 Suspension Links (short, medium, long) SCX24 Aufhängeglieder (kurz, mittel, lang) Bras de suspension SCX24 (court, moyen, long) SCX24 Bielle sospensioni (corte, medie, lunghe) 53
AXI31614 SCX24 Chassis Set SCX24 Karosseriesatz Ensemble de carrosserie SCX24 SCX24 Set telaio AXI31614 AXI200004 DYNS1217 AXI31608 AXI200004 AXI31611 AXI31611 AXI200003 AXI31614 AXI31609 AXI31613 AXI31611 AXI31620 DYNB0012 AXI31619 AXI31612 54
EN AXI200003 SCX24 B-17 Betty Body Clear SCX24 B-17 Betty Karosserie farblos B-17 Betty carrosserie transparente SCX24 Carrozzeria trasparente B-17 Betty SCX24 AXI40002 AXI40003 55
facebook.com/axialinc | instagram.com/axialracing | twitter.com/axialrc youtube.com/axialvideos | flickr.com/axialrc ©2020 Horizon Hobby, LLC. Axial, the Axial logo, B-17 Betty, SCX24, Dynamite, IC3, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. Nitto® and Trail Grappler® are registered trademarks of Nitto Tire U.S.A., Inc. The CRC name and logo are trademarks or registered trademarks of Casey Currie Motorsports and are used under license.
