is COMA 2000 Wireless Las! Loop AXHLPISABPISOOE The WLL (Wireless Local Loop} phone operates through a wireless connection instead of a phone wire, linking the subscribers of the general wire phone and the phone office. AX W-PBO0 & AX W-P1200, 2 CDMA2000 Fixed Wireless Phone has an elegant design with advanced features. A large 3-line dot matrix liquid crystal display provides user-friendly interface for quick and easy information display.
BALES OF CONTENTS Safety Precautions Checking Parts | Set ling up Your Phone Getting to Know Your Hon Display Icons Function Keys, Basic Operation Placing Calls . Redial Receiving Cal Adjusting Volumes Choosing the Ring Ton On-Hank Call . internal Phone Book The internal Phone Book Storing Numbers in Memo Searching for Numbers in Memory... 1g Erasing & Number in Memory. One-Touch Calling Two Touch Calling Used Features Call Log: Electronic Dialing. Displaying Your Phone Number 26 Muse . Silent Scratchpad ..
Nig CDA G00 Wiriness Local Loop CAUTERIZATION wim IN Bier PRECAUTIONS 1. Avoid placing the phone in a dusty location, of near a source of gas o fire. Don't shake, hit or drop the phone. # you clean the outside of the phone, use only a soft, dry cloth. The chemicals in alcohol, benzine or acetone can damage the surface of the phone, Do not twist or pull the cord out of the phone. Da not disassemble the phone. DO NOT use the power adapter if: «The power cord Is damaged.
HECKLING THE PARTS Nee you have unpacked your phone, make sure that you have all the parts shown baton, If any pica is missing or broken, please call your customer service. 1. Main Unit 2. Handset 3. CAI Adapter 4. User's Manual 5. Antenna 6, Battery 7.
Bern UP YOUR PHONE Installing the phone This phone operates by repaving DC power from the TASTELESS power adapter, which is connected 1o electrical outlet. The phone is equipped with a rechargeable battery to back up AC power failure.
EC Cato 209 ts va Lag 130: eso inn 7K SETTING UP YOUR PHONE Wall mount installation 1. Mark two mounting hole locations on the wall. 2. Drill twa holes at the marked location, 3. Attach the wall surmountable bracket. 4 Tighten the screws firmly. 5. Plug In power connector and route the cords in a groove, €. Install the phone onto the wall mount bracket hook. Push the phone against the wall and pull it down to lock. 7. Sower the antenna into antenna connector. 8.
SETTING UP YOUR PHONE Service Status Check Display in service area When the power cord is connected property, all segments in the LCD window will turn on briefly and Power LED will it. | All @8 The number of bars of signal strength indicator (antenna icon) TASTELESS indicates the strength of service signal of the area, » The display will show the greeting (TASTELESS as default), THU 10109 5:24P teems and date. You can change the greeting. (See page 34.
DT iN > SETTING UP YOUR PHONE Installing the battery 1. Remove screws with a screw driver and remove the battery cover on the bottom of the phone. 2. Plug in battery connector 3. Replace the battery cover and screws.
COMA 2000 Wireless Local Lou A XI-FROGEPISOR Antenna: Adjusting the antenna improves the sound quality of the call 2 MENU. Press to access the phone's menus. 3 CLEAR: Lets you clear your last entry. 4 STORE: Stores phone numbers, and any sailings you select in the menu within the phone's memory 5 MESSAGE: Press to retrieve messages. § RECALL Allows you to redial the fast number called. SETTING TO KNOW YOUR PHONE VOL/SC R: Lets you adjust sound revels and scroll through the menu opticians and displays.
> COMA 2060 css Let Loop AXP 1008 [apiarist ICONS Ions display on the screen to indicate what features you are using, signal strength and battery status etc... EEX TASTELESS THU 10/09 2:32P indicates the strength of the current signal, The more bars, Nfl i the stronger the signal, ym} indicates the level of battery power. The more bars, the more power. No When the battery is low, the icon blinks and an alert phone sounds. ~ JED) Indicates that you are using the phone's menu.
Coa 08 ono tg sig Se | — KEYS sm pros C0 GE @® Press this key to display the phone's main mean. Press this key to store a phone number in the phone book 10 save menu settings. Pros this key ta retrieve messages. Clears information from the display screen. -To erase one character from he display screen, press it once. To erase all the characters on the screen, press and hold down. To go back one step in menu mode, briefly press it incs.
= Basic Operation Placing Cali Redial Receiving Call Adjuring Volumes Choosing the Ring Tone On-Hook Call
CDM 2008 Wiretaps Lucas Loop AN W-PSTOBPIHIR Se IN PI. CALLS 1 Make sure your phone is turned on. 2 Pick up the handset to hear a dial tone. Foil men) When the phone fails to acquire service signal, you will hear PLEASE “No Service'tons (intermittent tone). DIAL 3 Dial the number to call. The LGD window displays the number. 0 7 4 Walt for a Moment or Dress «mse 5 When the other person answers, begin your conversation, [| CALLING. 6To end the call, replace the handset.
Ne COMA 2608 Wiriness Local Lapp LXSPIOMLPISIGR SL coven sn wis ost asp IK Ela FREE CALL This feature allows you to make a call without picking up the handset. 1 Press (8. 2 Enter the phone number you want to call. 3 When you hear the other pant answer, begin the conversation. For privacy conversation, just pick up the handset and continue conversation. ‘NOTE: tin intended OFF-HOOK recognition.
Augustine VOLUMES you can control the sound volumes including the key tone, earpiece, speaker and the ringer & Controlling key tone volume Tall Pres aS repeatedly until it reaches proper volume. KEY VOLUME & Controlling external speaker volume oil @mn ¢ Cross wie repeatedly during hand free call to adjust SPEAKER VOLUME external speaker volume. em & Controlling earpiece volume Yal Pick up the handset and press am repeatedly during PERPLEX VOLUME a phone call to adjust earpiece volume.
Phone book The Internal Phone Book Storing Numbers in Memory Searching for Numbers in Memory Erasing a Number in Memory One-Touch Calling Two-Touch Calling
INTERNAL PHONE BOOK Your phone has an internal "Phone Book" in which you can store up to 99 frequently calling names and numbers. |S [a NUMBERS IN MEMORY 1 Enter
toms She has already been stored, "OVERWRITE will display. Press wim to overwrite or press ad to go back to automatic location. KEEP SECRET ? 8 "KEEP SECRET?" displays. Press wise if no NO secret feature is necessary, To store the number in secret, select "YES" by pressing «ime or (9), (8) and press imbibe NOTE: secretly saved burner won't be displayed unless password is entered. 16 secretly saved number will prompt password entry.
Se crs sto Romans & Searching by Phone Number 1 Press om (2) (Phone book), (3) (Search), (2) (number) 2 Enter all or part of the umber you remember and Press wim. 3 The phone displays the memory location numbers ard names which has the number matches your entry. © NUMBER MATCHES’ appears when there's no beriberi matches your entry. 4 Press «2% or (5), (P) to search for the name you're poking for and press wae 10 display the number. NOTES ENTER LOCK CODE’ appears when you try to access secretly saved number.
Ny Co 200 Hess Loot Lop AX FtouBPISGS Sie iN [Eisner A NUMBER IN MEMORY & To Erase a Specific Number 1 (2) (Phone book), (Memory) 2 Press one of search options, (Name) or (2) (Number) or @ memory) Tall » 01: DAVID KiM 3 Enter name, address or phone number according to 05 : DANIEL search option. Select item (0 erase by pressing
4 Select YES by pressing «ii or G8), (73 Tall 5 Press «ds lo confirm. ~ ERASED CALLING Memory locations 01 ~ 03 are special one-touch dialing locations. You can dial the numbers stored in 01~08 by pressing just one key, 1 Pick up the handset or press Yat 2 Press and hold the number of the location (1-8) Memory 1 containing the number to be called. DAVID Kit 3 The name and number displays and dials automatically.
Useful Features Call Logs Display Your Phone Number Mute Silent Scratchpad Sending Your Phone Number Selecting Time Mode Setting the Alarm Checking and Clearing Call Times Setting Warning Beeps
3 COM 2088 Wises Lee Lou AX P0108 ALL HISTORY Your phone stores the last 10 outgoing calls and the last 10 incoming calls {only when Caller ID function is activated). You can display and redial these numbers. & Redialing Outgoing Calls 1 Press adm, History), (B) (Outgoing). NOTE: If there's no out going call history, "OUTGOING CALL MEMORY EMPTY! displays. OUTGOING 2 Press «oi mm or (37), (8) to select number 1a radial.
Ne COA HE Hires Loco Loop AX W-PEUEIPIRE wrote 7K & Erasing All Numbers In Call History 1 Press «in (8) (Security) Tull 2 Enter lock code OTE: Code's i set as from the factory. You can change lock code (see page 77) ENTER LOCK CODE You'll 8 3 Press (8) (Erase Logs) ERASE CALL LOGS 4 Select YES by pressing 22, or (9), @) . > YES 6 Press «2s to confirm. Soul EB ~ ERASED [3 striae PHONE NUMBER You can display your own phone number.
UEC Cots 00 tes cog ev xv as esy JIN Is working. The other party can na finger hear you, but you Gan hear them, 2 Cross wisdom (F)again to resume the conversation... BH. KEYPAD You can check your own phone number or save a number during a conversation without transmitting the dial tones to the other party. ‘This function is available only during a telephone conversation. 1 Press wie Key) during conversation. SILENT KEY’ blinks to indicate the function is waking.
[ Bec TIME MODE 1 Press wim (2) (Time Made). oil 80 EZ 2 Select time display mode by pressing 2 6). TIME MODE AMP AMP: Display D~12 hours with Aor P indicator 24 Hour: Display 00~24 hours $Press to save change. |S [— THE ALARM You can set the alarm sound daily or one time only. Ti em 1 Press eis, (3) (Fatima, (T) (Alarm). Tul 2 Select "SET" by pressing imitator (62), () and RESALE egress Enter alarm Tina and press wis. v : stem 3 im 4 Select alarm mods by pressing <2, ALARM MODE Daily: Alar sounds daily.
“SH sonatina sss HECKLING AND CLEARING CALL TIMES 4 Affecting the Last Gall Time 1 Press «22 , (3) (Time), (2) (Last Call). Toll xt Em 2 Press wienie 10 clear the display. LAST CALL TIME 3:25 £9 checking Accumulated Air Time of Incoming Calls Tall 1 Press «die . (8) (Air Time), INCOMING CALLS 3:25 @) oncoming. 2 Crass ati to clear the display. 4&9 Checking Accumulated Air Time of Outgoing Calls Tull 8 1 Press «2m , (Time), (D(A Time), OUTGOING CALLS 12:26:32 2 Press 10 clear the display.
Is = N COM 2900 Wins Lost Kop ANTIABORTIONIST motion Heine WARNING ALERT You can set your phone to sound warning beeps that indicate: each minute you are on a phone call when you are out of the service area &i somersetting 1 Minute Alert Toni 1 Press «iis, @)1 Min Alert). 2 Select ON or OFF by pressing 2, or (5), (5) 1 MINUTE ALERT 3 Cross «fis. > OFF Nero: Whir minute alert is set, the pane gives alert sound each minute while you are on a phone call.
Advanced Features Changing Greeting Message System Reset Restricting Use of the Phone Locking the Euphoria Changing the Lock Code Tone Length and Back Light
CA 2080 Wis Lol Lou AX N-3008P13068 SE HANGING GREETING MESSAGE This feature lets you change the greeting message that the phone displays while it's standby. 1 Press wits (2) (Security). Bull FED 0 2 Enter lock code 1. GREETING NOTE: Lock code is set as from the factory. 2. CHANGE CODE “To change rock code (see page 77) 3 Press Current greeting displays. Sal 4 Press «iis to change greeting. DO NOT TOUCH, 5 Enter your new greeting message by pressing the alphanumeric keys.
USE OF THE PHONE You can restrict the use of the phone by unauthorized persons. &F Restricting Outgoing Calls Tal 1 Press wis (5) (Security). 1. OUTGOING v 2 Enter lock code. 2. INTERNATIONAL NOTE: Lock code is set as from the factory. To change lock code (see page 77) All IE} Em 3 Press (Restrict), (Outgoing). OUTGOING CALL 4 Select "ON" by pressing <2 or G0), Press to save change. In this made, when you try to call, OUTGOING Tl CALL RESTRICTED" displays and no outgoing cal OUTGOING GALL goes through.
Ne Cato MOREISH ie 7K COKING / UNLOCKING THE PHONE You can lock your phone so that calls cannot be made by unauthorized persons. You can still receive incoming calls. Turning the phone off does not erase this feature; the phone stays in mode until you reset it. 1 Press wim (8) (Security) 2 Enter lack code ul 3 Press (E) {Alta Lock} 5 Select "ON" or "OFF" by pressing «Xs or (3), (3). 8 Press «ius to save the change. ~ LOCKED FRE 10/11 2:44P NOTE: Wah locked, the phone display LOCKED-.
Lr 7] SH Cato 100 Wests owt Leap preen IK ONE LENGTH AND BACK LIGHT Tone Length Some ARS you call may be able to recognize only long tones. You may have to change the tone length to LONG. 1 Press oii. (8) (Auto Setup), (3) line Length) il 2. Solect "NORMAL" or "LONG" by pressing 22 0). TONE LENGTH Press «Sm to save the change. > NORMAL & Back Light ‘You can control the length of back lighting of the display and the keypad. 1. Press «2, (5) (Auto Setup), (2) (Back light) 2.
Ni osm C0080 2000 Winches Local Loop AXHPIONBIPISNR AIN all Forwarding Call Forwarding is a feature that lets you forward your in corning calls to another phone number, even if your phone is turned off service area. Contact your service provider 10 activate Call Forwarding. all Waiting Call Waiting alerts you to a second incoming call while you are on the phone. When there's another incoming call, you will hear warming beep. To respond to the call waiting, press «wor hit shortly the hook switch once.
2 [Messes Service Message Service is network dependent feature and is available only when your service provider supports it. Check your service provider is providing message service before using this function. £3 Sending New Tot Messages 1 Press J. , MSG), (B) (New). 2 Enter destination number and press ie . 3 Write message using the alphanumeric keypad and Press iim Note: See page 19 ta see how 10 edit text. 4 Your pane number is displayed as call back number. You can change cal back number. Press «iim.
[ 5] > CoA 308 is Lat Lo XO COLORLESSNESS & Retrieving Text Message 1 When text message arrives, TEXT MESSAGE Fol ww = ARRIVED displays shortly and 53 appears in " plays shortly ore NEW TEXT MESSAGE the icon ding. ARRIVED! 2 Press JES. Message). 3 Press «Him ore), (#10 select message you want all to see and press wim. 4 The message, arrival time and call back number (if 1: VOICE [00] available} show up. If the message is long, it will be scrolled down in 3 seconds automatically.
COA 900 Weiss Lat np ARPSBERI0D om ZN & Erasing All Message ill + Press SE. (2) (Erase MSG) Tl to 2 Select YES with «22 or . ERASE ALL? 3 Press oI, . > YES £9 misinterpreting Message Lock 1 Press JESSE, Option), Lock). Toll 2 Select ON or OFF with £28, or (5), MESSAGE LOCK 3 Press on > oN While message lock is set, the phone will ask Lock Code whenever you try lo retrieve messages. & trendsetting Message Alert r— 1 Press 225, , (3) (MSG Option) (B) (MSG Alert, al 2 Select ON or OFF with JA, or (3.
MENU OPTION TABLE I Hn Explanation OUTGOING Flores ten phone numbers cad CAL mast recently HISTORY [Tm Sores ton phone testes of calls ” radioactive most recently SEARCH OPTION Used when searching 107 a phone Rams pong | SEARCH NAME / NUMBER / MEMORY | in the phone book by innumerably! ” stored memory number BOOK Used when staring & phone number and 1: STORE nam in the phone book P—— SEARCH OPTION Used when erasing a phone umber in : NAME / NUMBER / MEMORY | the phone book ALARM RELEASE / SET Set Release la
36 Colt 38 iss Lac op ARISTOPHANES ERASE HISTORY? Erase numbers in ganglion of incoming PHRASEOLOGY | noes cal history, 9 LANGUAGE ase Selects user interlace language. 1: DATA PORT DATA PORT Selects data port configuration SERIALIZE para |2DS SPEED 0S SPEED Selects data service speed SERVICE RECENTNESS MODE | RECEIVE MODE Semiconducting call rec mode VOICE SYNCOPATION FAX * Tie lock coda i preset ta G00G at the factory. * Batmen, press "CLEAR" to reborn to the previous menu.
Safety Information 1. SAFETY INFORMATION FOR FIXED WIRELESS TERMINALS .POET INITIALLY EXPLOSIVE ATMOSPHERES Turn your phone OFF when in any area with a potentially explosive atmosphere and obey all signs and instructions. Sparks in such areas could caulks e an explosion or fire resulting in bodily injury or even death.
SAR INFORMATION THIS MODEL PHONE MEETS THE GOVERNMENT 'S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency {Energy set by the Federal Communications Commission of the U.S.Government.These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population.
FCC Compliance Information This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: {1) This device may not cause harmful interference, and {2) This device must accept any interference received. Including interference that may cause undesired operation. Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
FCC RF EXPOSURE INFORMATION In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this phone complies with the FCC guidelines and these international standards.
