User Manual
Manuals
Brands
Axell Wireless Manuals
Electronics
BSR 3308-PS-NFPA
51
52
53
54
55
56
57
58
59
60
Table Of Contents
1 Introduction
1.1 Features
1.2 Repeater Models
1.3 Applications
1.4 NFPA Installation Architecture
1.5 Special Features
1.5.1 Smart-ALC Function
1.5.2 Switchable Bandwidth
1.5.3 Protection
1.6 Interfaces
2 Antenna Requirements
2.1 Base (Donor) Antenna Requirements
2.1.1 Required Antenna Information
2.1.2 Donor Antenna specifications
2.1.3 Installation Criteria
2.2 Service Antenna Requirements
2.2.1 Required Antenna Information
2.2.2 Recommended Antennas
2.2.3 Installation Criteria
3 Installing the Repeater
3.1 Pre-Installation Requirements
3.1.1 Safety Guidelines
3.1.2 Required BTS Information
3.1.3 Criteria for Repeater Installation Location
3.1.4 RF Cable Installation Guidelines
3.1.5 Overcurrent Protection
3.1.6 Grounding Wires Requirements
3.2 Overview of the Installation Procedure
3.3 Required Tools and Materials
3.4 Unpacking
3.5 Mounting the BSR 3308
3.5.1 Pre-Mounting Procedure
3.5.2 Installing the Mounting Bracket
3.5.3 For AC Models - Preparing Power Supply Cables
3.5.4 Mounting the Repeater
3.6 Grounding
3.7 Before Connecting the Antennas or Power
3.7.1 Verifying Isolation between Donor and Mobile Antennas
3.7.2 Verify Link between BTS and Repeater
3.8 Antenna Connections
3.9 Powering Up the BSR 3308 Repeater
3.9.1 Non-NFPA AC Model - Power Connection
3.9.2 BSR 3308-PS NFPA Power Connection
3.9.2.1 For AC repeater models:
3.9.2.2 For DC repeater models:
3.10 Dry Contact Alarm Connections
3.10.1 General
3.10.2 Alarm Connector Pinout
3.10.3 Load Restrictions
3.10.3.1 Alarm Dry Contact Output Restrictions
3.10.3.2 External Alarm Input Restrictions
3.10.4 Summary Alarms Trigger Criteria
3.10.5 BSR 3308-PS NFPA Installation Alarm Connections
4 Initial Setup and Commissioning
4.1 Open a Local WEB Session to the Repeater
4.1.1 Connecting to the Repeater
4.1.2 Configure the Computer Network Parameters
4.1.3 Login to the Repeater
4.2 Navigating the Web GUI Application
4.2.1 Operation Buttons
4.2.2 Axell3308 Tabs
4.2.3 CMU Pane and Tabs
4.3 Configuring the RF Parameters and Sub-band
4.3.1 Reducing the Max Output Power and Gain – Optional
4.3.2 Defining the Sub-band
4.3.3 Verify No Alarms are Generated
4.4 Configuring the External Alarms
4.5 Setting Date and Time
4.6 Configuring the System Parameters
4.6.1 The Communication Configuration Tab
4.6.2 IP Address Configuration
4.6.3 Configuring SNMP Trap Destinations
4.7 What Next?
5 Administration
5.1 User Management
5.1.1 User Levels
5.1.2 Viewing the List of Defined Users
5.1.3 Adding Users
5.1.4 Editing a User
5.1.5 Deleting a User
5.2 Repeater Level and Band Level Information
5.2.1 Repeater Level Information
5.2.2 Band Level Info
5.3 Software Upgrade
5.3.1 CMU Software Upgrade
5.3.2 Band Module Software Upgrade
5.4 Backup/Restore of Repeater Configuration
5.4.1 Backup of Repeater Configuration
5.4.2 Restoring Previous Repeater Configuration
5.4.3 Uploading New Configuration File to Repeater
5.4.4 Saving Configuration File to Computer
6 Maintenance and Troubleshooting
6.1 Periodic Maintenance
6.2 Failure Display
6.2.1 Status LEDs on the Repeater Front Panel
6.2.2 Alarms Screen
6.2.2.1 Alarm Description
6.2.2.2 Alarm Analysis
6.3 Viewing Alarms Log
6.4 Dry-Contact External Alarms
Appendix A: Specifications
Axell BSR
3308
-
PS NFPA
Produc
t
Descript
ion and
User’s
Manual
© Axell W
ireless Ltd
Doc PN 400
000413
1
Rev. 2.7
49
•
Click the
link in the
File
column.
•
Select the
location in the Browse dialog.
1
...
...
57
58
59
60
61
...
...
66
