Handbook
Table Of Contents
- AMENDMENT LIST RECORD SHEET
- INTRODUCTION
- 1.SAFETY CONSIDERATIONS
- 2.OVERVIEW/SYSTEM DESCRIPTION
- 3.SPECIFICATION
- 3.150-063701 Parts Lists
- 3.1.1Base Antenna Side UHF Duplex/PA Shelf 50-063702 Parts List
- 3.1.2Downlink UHF 5 Channel Shelf 50-063703 Parts List
- 3.1.3Uplink UHF 4 Channel Shelf 50-063704 Parts List
- 3.1.4Tunnel side UHF Duplex/PA Shelf 50-063705 Parts List
- 3.1.5UHF Simplex Shelf 50-063706 Parts List
- 3.1.6Power Supply Shelf 50-063707 Parts List
- 3.2Technical Specification
- 3.3Mechanical Specification
- 3.150-063701 Parts Lists
- 4.SYSTEM DRAWINGS
- 4.1Drg. No. 50-063751, Channelised Cell Enhancer Rack Layout Drawing
- 4.2Drg. No. 50-063781, Channelised Cell Enhancer System Diagram
- 4.3Drg. No. 50-063792, Base Side Duplex Shelf Outline Drawing
- 4.3Drg. No. 50-063793, Downlink Channels Shelf Outline Drawing
- 4.4Drg. No. 50-063794, Uplink Channels Shelf Outline Drawing
- 4.5Drg. No. 50-063795, Tunnel Side Duplexer Shelf Outline Drawing
- 4.6Drg. No. 50-063796, UHF Simplex Shelf Outline Drawing
- 4.7Drg. No. 50-063797, Power Supply Shelf Outline Drawing
- 5.SUB-UNIT MODULES
- 5.1UHF Duplex Shelf 50-063702
- 5.25 Channel UHF Downlink Shelf 50-063703
- 5.3UHF Uplink 4 Channel Shelf 50-063704
- 5.4UHF Duplex/PA Shelf 50-063705
- 5.5UHF Simplex Channel Shelf 60-063706
- 5.6Power Supply Shelf 50-063707
- 6.INSTALLATION
- 7.MAINTENANCE
- APPENDIX AINITIAL EQUIPMENT SET-UP CALCULATIONS
Denver Channelised CE
User/Maintenance Handbook
Handbook Nō.-50-063708HBKM Issue No:-2
Date:-03/11/2003
Page:-
37 of 51
5.2 5 Channel UHF Downlink Shelf 50-063703
5.2.1 3dB Splitter 905-002603) See section 5.1.2
5.2.2 3 Way Splitter/Combiner (05-003803)
5.2.2.1 Description
The 3 way Splitter/Combiner used is a ‘Zinger’ type design for accurately matching three
RF signals to a single port, whilst maintaining an accurate balance between ports, and
ensuring that the VSWR and insertion losses attain the best possible specification. They are
specialist passive devices and must be replaced in the unlikely event of failure.
5.2.2.2 Technical Specification
PARAMETER SPECIFICATION
Frequency Range: 380 - 520 MHz
Bandwidth: 140 MHz (typical)
Inputs: 3
Outputs: 1
Insertion Loss: 5.2 dB (typical)
Isolation: >18 dB
Return Loss (VSWR) – Input: Better than 1.35:1
Return Loss (VSWR) – Output: Better than 1.35:1
Impedance:
50 ς
Power Rating – Splitter: 20 Watts
Power Rating – Combiner: 0.5 Watt
Connectors: SMA female
Size: 54 x 44 x 21 mm (including
connectors)
Weight: 200 gm (approximately)