User Manual
Table Of Contents
- AMENDMENT LIST RECORD SHEET
- INTRODUCTION
- 1.SAFETY CONSIDERATIONS
- 2.OVERVIEW/SYSTEM DESCRIPTION
- 3.SPECIFICATION
- 4.SYSTEM DRAWINGS
- 5.SUB-UNIT MODULES
- 5.1VTA Downlink Duplexer Shelf 60-025302 (4U chassis)
- 5.2VTA Downlink Amplifier Shelf (50-025303, 8U Chassis)
- 5.2.1UHF 3dB Splitter (05-002603)
- 5.2.2¼Watt 0- -30dB Switched Attenuator \(10-00
- 5.2.3Low Noise Amplifier (11-006102)
- 5.2.4Low Noise Amplifiers (11-007302 & 11-007402)
- 5.2.4.1Description
- 5.2.4.2Technical Specification, (11-007302)
- 5.2.4.3Technical Specification (11-007402)
- 5.2.4.4Drg. No. 11-007302, LNA Assembly With Alarm Relay
- 5.2.4.5Drg. No. 11-007370, LNA RF Circuit Diagram
- 5.2.4.6Drg. No. 11-007371, LNA DC Wiring Diagram
- 5.2.5.7Drg. No. 11-003971, LNA DC Circuit Diagram
- 5.2.63 Stage Amplifier Alarm Boards (12-002201)
- 5.2.7450MHz 20W Power Amplifier (12-004201)
- 5.2.8Single DC/DC Converter (13-001702)
- 5.2.924V Single Relay Board (80-008902)
- 5.2.1024V 410W Power Supply (96-300054)
- 5.3VTA Downlink Channel Shelf (50-025304)
- 5.4VTA Uplink Duplexer Shelf (50-025305, 4U Chassis)
- 5.5VTA Uplink Amplifier Shelf (50-025306, 8U Chassis)
- 5.5.120Watt Class A Power Amplifier (12-016301)
- 5.5.2Automatic Gain Control (17-001101, Det. & 17-001201, Atten.)
- 5.5.2.1Description
- 5.5.2.2Technical Specification
- 5.5.2.3Drg. No. 17-001101, ACG Detector Assembly
- 5.5.2.4Drg. No. 17-001171, AGC Detector Circuit Diagram
- 5.5.2.5Drg. No. 17-001171C, AGC Detector Parts List
- 5.5.2.6Drg. No. 17-001201, AGC Attenuator Assembly Drawing
- 5.5.2.7Drg. No. 17-001270, AGC Attenuator Circuit Diagram
- 5.5.2.8Drg. No. 17-001270C, AGC Attenuator Parts List
- 6.INSTALLATION
- 7.MAINTENANCE
- APPENDIX AINITIAL EQUIPMENT SET-UP CALCULATIONS
9 Way Channelised UHF Cell Enhancer
Maintenance Handbook
H/book Number:-50-025301HBKM
Issue No:-
1
Date:-04/07/2003
Page:-
48 of 69
5.3.3 Channel Control Module (17-002101)
5.3.3.1 Description
The purpose of the channel control modules is to change the channel selective module
frequencies by means of a series of D.I.P switch banks, each switch corresponding to a
different ‘frequency bit’.
5.3.3.2 Technical Specification
Below shows the pin assignments for each switch on a channel control module.
IDC PIN 25-way Connector Function
1 13 Freq. bit 1 (12.5kHz)
2 25 Freq. bit 2 (25kHz)
3 12 Freq. bit 3 (50kHz)
4 24 Freq. bit 4 (100kHz)
5 11 Freq. bit 5 (200kHz)
6 23 Freq. bit 6 (400kHz)
7 10 Freq. bit 7 (800kHz)
8 22 Freq. bit 8 (1.6MHz)
9 9 Freq. bit 9 (3.2MHz)
10 21 Freq. bit 10 (6.4MHz)
11 8 Freq. bit 11 (12.8MHz)
12 20 Freq. bit 12 (25.6MHz)
13 7 Freq. bit 13 (51.2MHz)
14 19 Freq. bit 14 (102.4MHz)
15 6 Freq. bit 15 (204.8MHz)
16 18 Freq. bit 16 (409.6MHz)
17 5 Module alarm
18 17
19 4
20 16
21 3
N/C
22 15 +5V
23 2 0V
24 14 Switched 12V
25 1 0V
26 --- ---