User Manual
Table Of Contents
- AMENDMENT LIST RECORD SHEET
- INTRODUCTION
- 1.SAFETY CONSIDERATIONS
- 2.OVERVIEW/SYSTEM DESCRIPTION
- 3.SPECIFICATION
- 4.SYSTEM DRAWINGS
- 5.SUB-UNIT MODULES
- 5.1VTA Downlink Duplexer Shelf 60-025302 (4U chassis)
- 5.2VTA Downlink Amplifier Shelf (50-025303, 8U Chassis)
- 5.2.1UHF 3dB Splitter (05-002603)
- 5.2.2¼Watt 0- -30dB Switched Attenuator \(10-00
- 5.2.3Low Noise Amplifier (11-006102)
- 5.2.4Low Noise Amplifiers (11-007302 & 11-007402)
- 5.2.4.1Description
- 5.2.4.2Technical Specification, (11-007302)
- 5.2.4.3Technical Specification (11-007402)
- 5.2.4.4Drg. No. 11-007302, LNA Assembly With Alarm Relay
- 5.2.4.5Drg. No. 11-007370, LNA RF Circuit Diagram
- 5.2.4.6Drg. No. 11-007371, LNA DC Wiring Diagram
- 5.2.5.7Drg. No. 11-003971, LNA DC Circuit Diagram
- 5.2.63 Stage Amplifier Alarm Boards (12-002201)
- 5.2.7450MHz 20W Power Amplifier (12-004201)
- 5.2.8Single DC/DC Converter (13-001702)
- 5.2.924V Single Relay Board (80-008902)
- 5.2.1024V 410W Power Supply (96-300054)
- 5.3VTA Downlink Channel Shelf (50-025304)
- 5.4VTA Uplink Duplexer Shelf (50-025305, 4U Chassis)
- 5.5VTA Uplink Amplifier Shelf (50-025306, 8U Chassis)
- 5.5.120Watt Class A Power Amplifier (12-016301)
- 5.5.2Automatic Gain Control (17-001101, Det. & 17-001201, Atten.)
- 5.5.2.1Description
- 5.5.2.2Technical Specification
- 5.5.2.3Drg. No. 17-001101, ACG Detector Assembly
- 5.5.2.4Drg. No. 17-001171, AGC Detector Circuit Diagram
- 5.5.2.5Drg. No. 17-001171C, AGC Detector Parts List
- 5.5.2.6Drg. No. 17-001201, AGC Attenuator Assembly Drawing
- 5.5.2.7Drg. No. 17-001270, AGC Attenuator Circuit Diagram
- 5.5.2.8Drg. No. 17-001270C, AGC Attenuator Parts List
- 6.INSTALLATION
- 7.MAINTENANCE
- APPENDIX AINITIAL EQUIPMENT SET-UP CALCULATIONS
9 Way Channelised UHF Cell Enhancer
Maintenance Handbook
H/book Number:-50-025301HBKM
Issue No:-
1
Date:-04/07/2003
Page:-
47 of 69
5.3 VTA Downlink Channel Shelf (50-025304)
5.3.1 UHF 3dB Splitter (05-002603) See section 5.2.1
5.3.2 4-Way Splitter (05-003401)
5.3.2.1 Description
The Splitter/Combiners used are devices for accurately matching two or more RF signals
to single or multiple ports, whilst maintaining an accurate 50Ω load to all inputs/outputs
and ensuring that the VSWR and insertion losses are kept to a minimum. Any unused
ports will be terminated with an appropriate 50Ω load.
5.3.2.2 Technical Specification
PARAMETER SPECIFICATION
Frequency range: 170 – 550MHz
Bandwidth: 280MHz
Rejection: >14dB
Insertion loss: 6.5dB (in band, typical)
Connectors: SMA
Weight: <1.5Kgm
operational
:
-10ΒC to +55ΒC
Temperature
range:
storage
-40ΒC to +70ΒC