User Manual
Table Of Contents
- AMENDMENT LIST RECORD SHEET
- INTRODUCTION
- 1.SAFETY CONSIDERATIONS
- 2.OVERVIEW/SYSTEM DESCRIPTION
- 3.SPECIFICATION
- 4.SYSTEM DRAWINGS
- 5.SUB-UNIT MODULES
- 5.1VTA Downlink Duplexer Shelf 60-025302 (4U chassis)
- 5.2VTA Downlink Amplifier Shelf (50-025303, 8U Chassis)
- 5.2.1UHF 3dB Splitter (05-002603)
- 5.2.2¼Watt 0- -30dB Switched Attenuator \(10-00
- 5.2.3Low Noise Amplifier (11-006102)
- 5.2.4Low Noise Amplifiers (11-007302 & 11-007402)
- 5.2.4.1Description
- 5.2.4.2Technical Specification, (11-007302)
- 5.2.4.3Technical Specification (11-007402)
- 5.2.4.4Drg. No. 11-007302, LNA Assembly With Alarm Relay
- 5.2.4.5Drg. No. 11-007370, LNA RF Circuit Diagram
- 5.2.4.6Drg. No. 11-007371, LNA DC Wiring Diagram
- 5.2.5.7Drg. No. 11-003971, LNA DC Circuit Diagram
- 5.2.63 Stage Amplifier Alarm Boards (12-002201)
- 5.2.7450MHz 20W Power Amplifier (12-004201)
- 5.2.8Single DC/DC Converter (13-001702)
- 5.2.924V Single Relay Board (80-008902)
- 5.2.1024V 410W Power Supply (96-300054)
- 5.3VTA Downlink Channel Shelf (50-025304)
- 5.4VTA Uplink Duplexer Shelf (50-025305, 4U Chassis)
- 5.5VTA Uplink Amplifier Shelf (50-025306, 8U Chassis)
- 5.5.120Watt Class A Power Amplifier (12-016301)
- 5.5.2Automatic Gain Control (17-001101, Det. & 17-001201, Atten.)
- 5.5.2.1Description
- 5.5.2.2Technical Specification
- 5.5.2.3Drg. No. 17-001101, ACG Detector Assembly
- 5.5.2.4Drg. No. 17-001171, AGC Detector Circuit Diagram
- 5.5.2.5Drg. No. 17-001171C, AGC Detector Parts List
- 5.5.2.6Drg. No. 17-001201, AGC Attenuator Assembly Drawing
- 5.5.2.7Drg. No. 17-001270, AGC Attenuator Circuit Diagram
- 5.5.2.8Drg. No. 17-001270C, AGC Attenuator Parts List
- 6.INSTALLATION
- 7.MAINTENANCE
- APPENDIX AINITIAL EQUIPMENT SET-UP CALCULATIONS
9 Way Channelised UHF Cell Enhancer
Maintenance Handbook
H/book Number:-50-025301HBKM
Issue No:-
1
Date:-04/07/2003
Page:-
35 of 69
5.2.7 450MHz 20W Power Amplifier (12-004201)
5.2.7.1 Description
The power amplifiers fitted to this unit are multi-stage, solid state power amplifiers. Class
A circuitry is employed throughout the units to ensure excellent linearity over a wide
dynamic frequency range. All the semi-conductor devices are very conservatively rated to
ensure low device junction temperatures and a long, trouble free working lifetime.
The power amplifiers should require no maintenance over their operating lives. Under no
circumstances should the cover be removed or the side adjustments disturbed unless it is
certain that an amplifier has failed; since they are critically aligned during manufacture
and any re-alignment will require extensive test equipment.
5.2.7.2 Technical Specification
PARAMETER SPECIFICATION
Frequency Range: 350 – 550MHz (tuned to spec.)
Bandwidth: 20MHz (tuned to spec.)
Maximum Output Power: >20W (each)
Gain: 30dB
1dB Compression Point: <+43dBm
3rd Order Intercept Point: <+54dBm
VSWR: better than 1.45:1
Connectors: SMA female
Supply: 3.50A @ 24V DC
Size: 276 x 78 x 40mm (ex. Cons. & h’sink)
Weight: 1.5 kg (approx., excl. h’sink)
operational: -10°C to +55°CTemperature
range:
storage: -40°C to +70°C