Installation Guide

ManualsBrandsAXC ManualsSuper DutyAXC B0001 2018-Up Ford Super Duty

INCLUDED IN HARDWARE KIT:

B0001

2018-Up Ford Super Duty F250 / F350

INSTALLATION GUIDE

PRIOR TO INSTALLATION

A) Install the flares according to these written instructions with the hardware provided.

WARNING: Failure to install according to these instructions will invalidate the

warranty. This includes, but is not limited to, using alternative installation methods,

hardware, or materials. DO NOT USE: Loctite, Superglue, or similar products on the

hardware or the flares. Install flares on cleaned vehicle surfaces.

B) Fit: Verify the fit of the flares to vehicle prior to installation (some filing, sanding, or

cutting may be necessary to ensure proper fit).

C) Painting: (Optional) if paint is desired it must be done prior to installing flares on

vehicle. Clean outer surface with a good grade degreaser. DO NOT USE LACQUER

THINNER OR ENAMEL REDUCER AS A DEGREASER. Wipe outer surface

thoroughly with a tack rag prior to paint. Application of plastic adhesion promoter for

ABS plastic as per your paint system manufacturer’s recommendations is required.

Paint flares using a high-quality enamel, or polyurethane automotive paint. If painting

edge trim (not recommended), use a flex additive.

D) Performance: Using larger tires may increase the area required to turn the vehicle.

Some tire/rim combinations may require lowering bump stops and or installing

steering stops to prevent tire from contacting flare.

E) Exhaust System: Modifications may be necessary to maintain a minimum 4”

clearance between flares and exhaust pipes. (Exhaust gases should not vent directly

onto flares)

F) Metal Protection: All exposed fasteners and bare metal should be treated with

rust resistant paint BEFORE installing flares. Spray inner fender wells with

undercoating AFTER flare attachments have been completed.

G) Decals: Flares may interfere with existing decals on vehicle. If you wish, remove

decals prior to installation of flares.

H) Care & Cleaning: Fender flares are built to last; any detergent you use to wash your

vehicle is sufficient to clean the flare. Do not use any harsh abrasive detergents.

TOOLS FOR EASY INSTALLATION:

 Soft Cloth or Alcohol Wipe

 1/2" or 13mm Wrench

 Utility Knife

 Socket Wrench

 7/32” Socket

 #2 Phillips Screwdriver



Grease Pencil

PLEASE READ: Dirt and debris can become lodged

between the fender flares and the vehicle’s fenders,

causing scratching and paint wear from vibration.

Manufacturer is not responsible for any damage, and

the installation of our fender flares is done with the

buyer’s understanding that this scratching and paint

wear may occur.

LIMITED LIFETIME WARRANTY AGAINST ANY

MANUFACTURING DEFECTS: To claim warranty

you must provide Proof of Purchase.

SS Pocket Torx

Bolt

34 pcs

SS Pocket

Washer

34 pcs

Pocket Nylock

Nut

34 pcs

T-45 Torx Bit

1 pc

Short “U” Clip

6 pcs

Long “U” Clip

8 pcs

Plastic Retainer

2 pcs

10.

Wiper Style Edge

Trim

330 inches

Foam Tabs

8 pcs

Truss-Head

Screw

14 pcs

Summary of content (5 pages)

PAGE 1
B0001 2018-Up Ford Super Duty F250 / F350 INSTALLATION GUIDE PRIOR TO INSTALLATION TOOLS FOR EASY INSTALLATION: A) Install the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions will invalidate the warranty. This includes, but is not limited to, using alternative installation methods, hardware, or materials. DO NOT USE: Loctite, Superglue, or similar products on the hardware or the flares.
PAGE 2
SECTION 1: EDGE TRIM INSTALLATION A) Peel 2-3 inches of red vinyl backing away from supplied edge trim tape. Applying the adhesive side of the edge trim to the inner side of the flare, affix the edge trim to the top edge of the flare (the portion that comes in contact with the side of the vehicle). A Press edge trim into place along the top edge of the flare in one-foot increments, pulling red vinyl backing free as you continue to work your way around the top edge of the flare.
PAGE 3
SECTION 3: FRONT FLARE INSTALLATION 4 Remove 6 factory screws with a 7/32” socket wrench. Retain screws for reinstallation. NOTE: For Platinum Edition, there are additional screws to be removed and retained. 6 Line up holes in the Inner Bracket with the 4-most upper factory holes in wheel well. 8 Aligning flare on fender, press inward on the flare to line up the flare mounting holes with the clips on the Inner Bracket. Install 3 supplied Truss-Head Screws through the flare and into the inner piece.
PAGE 4
10 Completed Front Flare Installation. SECTION 5: REAR FLARE INSTALLATION 11 Align Rear Flare on fender and mark 4 hole locations with a grease pencil. Remove factory fastener on rear splash shield. 13 Hole locations. 12 14 Center a supplied Foam Tab over each mark made in Step 12, folding each tab over the wheel well lip.
PAGE 5
15 16 Slide a supplied Long “U” Clip over each foam tab, making edge of clip flush with outer edge of wheel well lip as shown. While holding flare to vehicle, start supplied Truss-Head Screws through the 4 topmost mounting holes in flare and into clips installed in Step 15. Apply pressure to flare towards vehicle body at each fastening point and tighten all fasteners. 17 18 Install supplied Plastic Retainer through flare and into factory hole at rear of wheel well. Completed Rear Flare Installation.