Installation Guide

ManualsBrandsAwnings in a Box ManualsAwnings8 ft. Designer Manually Retractable Awning (36.5 in. Projection) in Burgundy

Basic Tools Required (not included)



Tape Measure & Pencil Level

 Phillips Screwdriver



Drill with ¼” bit (Cement or Masonry bit for concrete installation)



Ladder

Note: Make sure that the awning you purchased exceeds the window width.

Allow for clearance for windows or doors that open outward.

General Comments



Wash your hands before installation when handling the fabric.



Always be careful with the fabric during installation.

Drills, screwdrivers and other items can puncture the fabric.

Punctures during installation are not covered by the warranty.



A second person to assist in holding the awning during installation is RECOMMENDED.

Included in Awning Kit

Item

Part Number

Description

Awning Designer

4ft

6ft

8ft

1200145

Head Rod Clamps

1200170

Powder-Coated Black

Hinges w/bolts

1200171

Powder-Coated Black

Eye Ends

1200094

Powder-Coated Black

Screws

#10 (1 ½”)

1200172

Powder-Coated Black

“T”- Connectors

1200146

Pulleys

1200720

Internal Connectors

1200176

Powder-Coated Black

Cleat

Installation Instructions

Designer Awnings in a box™

Summary of content (6 pages)

PAGE 1
Installation Instructions Designer Awnings in a box™ Basic Tools Required (not included)     Tape Measure & Pencil Level Phillips Screwdriver Drill with ¼” bit (Cement or Masonry bit for concrete installation) Ladder Note: Make sure that the awning you purchased exceeds the window width. Allow for clearance for windows or doors that open outward. General Comments  Wash your hands before installation when handling the fabric.  Always be careful with the fabric during installation.
PAGE 2
I 1200180 Powder-Coated Black Finials 2 2 2 J 1410760 Instruction Sheet 1 1 1 K 1020010 21’ Pull Cord 1 1 1 L N/A Awning Fabric Cover 1 1 1 M 1300262 2 2 2 N 1300258 Powder-Coated Black 4” Finial Bar 2 2 2 O 1300222 Head Rod Bar (Inside Threaded Pipe with Cap on end) 2 2 2 P 1300225 Front Bar 2 2 2 Q 1300223 Center Bar (Inside Threaded Pipe both ends) 0 2 4 Powder-Coated Black Arm Bar (Outside Threaded Pipe both ends) (Inside / Outside Threaded Pipe) In
PAGE 3
Designer Awning Assembly and Mounting 1. Measure and mark wall for head rod clamps 6 inches in from both sides of the window. a) Drill pilot or anchor holes for each head rod clamp. b) Fasten both head rod clamps to the wall, use a level to ensure clamps will be level with each other and centered above window. WINDOW 2. Optional Pulley a) Install one pulley on the left head rod clamp hook. Install two pulleys on the side you want the pull cord. (One each hook) 3.
PAGE 4
6. Add the "T" Connectors to the ends of front bar N E 7. Screw the eye end onto the Arm (repeat on other arm). M C 8. Thread T connector onto arm pipe. M E 9. Measure 36" down from head rod on each side of awning and attach camelback hinges to wall making sure arms are straight when viewed from front. Decreasing this dimension will increase the awnings projection from wall to clear door openings if desired. 10. Remove middle screw on the camelback hinge. 11.
PAGE 5
b) Tie one end of the pull cord to the left front bar of the awning, thread through left side pulley, then over closet right side pulley and down to the cleat and back up to open right pulley, tie the end of pull cord to the right and left side of the front bar. Draw all slack in pull cord towards cleat and tie off.
PAGE 6
Customer satisfaction and end user satisfaction is a number one concern and priority. THE WARRANTY Warranties apply for 1 year from date of original purchase with proof of purchase (original receipt) Customer satisfaction and end user satisfaction is a number one concern and priority.