Installation Guide

ManualsBrandsAwnings in a Box ManualsAwnings8 ft. Traditional Manually Retractable Awning (26.5 in. Projection) in Sand

Basic Tools Required (not included)



Tape Measure & Pencil Level

 Phillips Screwdriver



Drill with ¼” bit (Cement or Masonry bit for concrete installation)



Ladder

Note: Make sure that the awning you purchased exceeds the window width.

Allow for clearance for windows or doors in opens outward.

General Comments



Wash your hands before installation when handling the fabric.



Always be careful with the fabric during installation.

Drills, screwdrivers and other items can puncture the fabric.

Punctures during installation is not covered by the warranty.



A second person to assist in holding the awning during installation is

RECOMMENDED.

Included in awning kit

Item

Part Number

Description

Awnings Traditional & Classic

Designs

4ft

6ft

8ft

1200145

Head Rod Clamps

1200144

Hinge w/bolt attached

1200148

Eye End

1200093

Screws #10 (1 ½”)

1200146

Elbow

1200146

Pulleys

1200720

Internal Connectors

1200142

Cleat

Installation Instructions

Traditional Awnings in a box™

Classic Awnings in a Box™

Summary of content (6 pages)

PAGE 1
Installation Instructions Traditional Awnings in a box™ Classic Awnings in a Box™ Basic Tools Required (not included)     Tape Measure & Pencil Level Phillips Screwdriver Drill with ¼” bit (Cement or Masonry bit for concrete installation) Ladder Note: Make sure that the awning you purchased exceeds the window width. Allow for clearance for windows or doors in opens outward. General Comments  Wash your hands before installation when handling the fabric.
PAGE 2
I 1410010 Instructions Sheet 1 1 1 J 1020010 21’ Pull Cord 1 1 1 K N/A Awning Fabric Cover 1 1 1 L 1300224 Arms (Outside Threaded Pipe) 2 2 2 M 1300222 (Inside Threaded Pipe with Black Cap on end) 2 2 2 N 1300225 Front Bar 2 2 2 O 1300223 Center Bar 0 2 4 Head Rod Bar (Inside / Outside Threaded Pipe) (Inside / Outside Threaded Pipe) ASSEMBLY O M G E G O DRAWING Instructions Sheet
PAGE 3
Traditional & Classic Awning Assembly and Mounting 1. Measure and mark wall for head rod clamps 6 inches in from both sides of the window. a) Drill pilot or anchor holes for each head rod clamp. b) Fasten both head rod clamps to the wall, use a level to ensure clamps will be level with each other and centered above window. WINDOW 2. Optional pulley a) Install one pulley on the left head rod clamp hook. Install two pulleys on the side you want the pull cord. (One each hook) 3.
PAGE 4
Awning Cover Insert Head Rod Bar Here Head Rod Pocket Head Rod Clamp (mounted on wall) Insert Front Bar Here Front Bar Pocket Insert Side Arms Here Side Arm Pocket 6. Add the elbows to the ends of front bar. N E 7. Screw the Eye end onto the Arm (repeat on other arm). C L a) Slide the Arms into the side pocket of awning. b) Screw into the elbows on front bar. 8. Straighten the Front bar; making sure the awning is level and straight. 9. Screw both camelback hinges into the wall. 10.
PAGE 5
11. For Optional Pulley: Install tie down cleat on the side with the two pulleys. (4-6” below the bottom of the awning) Tie one end of the pull cord to the left front bar of the awning, thread through left side pulley, then over closet right side pulley and down to the cleat and back up to open right pulley, tie the end of pull cord to the right and left side of the front bar. Draw all slack in pull cord towards cleat and tie off.
PAGE 6
Customer satisfaction and end user satisfaction is a number one concern and priority. THE WARRANTY Warranties apply for 1 year from date of original purchase with proof of purchase (original receipt) Customer satisfaction and end user satisfaction is a number one concern and priority.