DTVS-1B User Guide Digital Satellite Receiver
Digital Satellite Receiver DTVS-1B User Guide Safety Instructions - Always read the safety instructions carefully. Keep this User's Manual for future reference. Keep this equipment away from humidity. Lay this equipment on a reliable flat surface before setting it up. Do not stand it on soft furnishings. If any of the following situation arises, get the equipment checked by a service Technician: ● The equipment has been exposed to moisture. ● The equipment has been dropped and damaged.
Contents Safety Instructions ........................................................................................................................................................... 2 Contents .............................................................................................................................................................................. 3 About the Set Top Box ..................................................................................................................
Digital Satellite Receiver DTVS-1B User Guide About the Set Top Box This DVB-S Satellite Receiver is a Free-To-Air digital satellite receiver, allowing you to access freeto-air digital Satellite TV channels and radio broadcasts on your TV set. Its digital reception covers VHF & UHF band. Compared with analog TV programs, digital TV programs eliminate the noise and interference by offering high quality video and audio.
Front Panel and Rear Panel Illustration Front panel 1 2 3 4 1. POWER To turn the standby mode ON/OFF 2. ▲ To change the channel upward 3. ▼ To change the channel downward 4. LED digital display: To display the status of the receiver: when playing menu, it shows "MENU"; when watching TV channel, it shows the channel No.; when in standby mode, it shows the time. When searching channels, it shows "TUNE". Rear panel 1 3 5 8 13/18V 500m A Max .
Digital Satellite Receiver DTVS-1B User Guide Remote Control Remote key functions 1. POWER To turn the standby mode ON/OFF 1 2 2. MUTE To mute or recover the sound of the receiver 1 3 2 3 3. Numeric buttons (0-9) To control the 5 4 6 numerical operation and to change programs directly 7 8 9 4. SUBTL To select closed caption TV/RADIO SUBTL 5 0 4 5. TV/RADIO To switch the program between TV and Radio EPG TXT 6 7 6. EPG To introduce some program info to the user 8 9 OK 7.
Installing the Batteries Remove the battery cover from the remote control and put two AAA size batteries inside the compartment. The diagram inside the battery compartment shows the correct way to install the batteries Caution: 1. Keep batteries out of childrens’ reach. 2. Don’t attempt to recharge, short-circuit, disassemble, heat or throw the batteries into fire. 3. Always replace both batteries at the same time. Never mix new and old batteries or batteries of a different type. 4.
Digital Satellite Receiver DTVS-1B User Guide Connecting to Equipment How to get good reception There are many ways to connect the satellite receiver to your home entertainment system, depending on the equipment and connection types you have. However, for the best video/audio quality, use the higher quality YCbCr and S/PDIF connections if available.
First Time Installation Note: Be sure to turn on the main power at the rear of your receiver before using the receiver. Before you press power button, the receiver is on standby mode. After all the connections have been made properly switch on your TV. Make sure the receiver is connected to the mains and press the POWER button to switch the receiver on. If you are using the receiver for the first time or restored to factory default, the Main Menu will be displayed.
Digital Satellite Receiver DTVS-1B User Guide Basic Operations Switch program 1. Press the numeric buttons (0~9) on the remote control to select the channel number you want. 2. Press the CH▲/▼key on the remote control or the front panel to change the available channels upward/downward. 3. Press the RECALL button to view the previous channel selected. Volume control 1. Press the Vol+/- button on the remote control or front panel to adjust the volume. The following volume bar will appear on screen.
Basic Operations Teletext service 1. Press the TXT button to open a teletextpage (if the teletext is transmitted) 2. Press the TXT button again or press the EXIT button to close the teletext. EPG (Electric Program Guide) 1. Press the EPG button to view the EPG information that are provided by the content providers. 2. Press ◄/► show EPG for the adjacent channels, and then press OK to select the program/channel to watch. 3.
Digital Satellite Receiver DTVS-1B User Guide Main Menu This section guides you to walk through of all options on the Menu screen. Navigation in the main menu 1. Press the MENU button to bring up the main menu. 2. Press the ▲/▼ button to move upward/downward to the desired menu. press the ◄/► button to move to the sub menu and press ▲/▼ to choose the one you want. 3. Press the OK button to enter into the sub menu you select. 4. Press the EXIT button to exit the main menu.
Main Menu Menu Tree Main Menu Channel Manager Channel Organiser New Channel Edit Channel Delete All Installation Satellite Setup Blind Scan Transponder Setup DisEqc Motor Setup Factory Default Reset Box Info System Setup Language Setup OSD Setup TV Setup Time Setup Password Setup Wakeup Timer Accessories S/W Upgrade Version Signal Monitoring Country Setup EPG 13
Digital Satellite Receiver DTVS-1B User Guide Channel Organiser Channel Organiser 1. Go to Main Menu > Channel Manager > Channel Organiser. 2. Press RED button to Skip, GREEN button to lock the channel, BLUE button to delete the channel; press▲/▼to select the channel; press INFO button to rename the channel name; press FAV button to set the favourite list; press TV/R button to change the program mode between TV and Radio. 3. Press EXIT to exit the menu. New Channel 1.
Channel Organiser Edit Channel 1. Go to Main Menu > Channel Manager > Edit Channel 2. Press ▲/▼ and ◄/► to select the item and press numerical 0~9 to set as you want, then Press OK . 3. Press EXIT to exit the menu. Delete All 1. Go to Main Menu > Channel Manager > Delete All 2. There are five items you can chose: All TV Service, ALL Radio Service, All FTA Service, All Scrambled, All Transponders. Press ▲/▼ to choose the item you want to delete.
Digital Satellite Receiver DTVS-1B User Guide Installation Satellite Setup 1. Go to main menu ﹥ Installation ﹥ Satellite Setup 2. Press ▲/▼ to choose LNB No., LNB power, 22kHz, DisEqc, DisEqc Switch and press OK to select the satellite that you want to scan. There will be a window displayed to confirm with you if you want to scan. Press ▲/▼to choose YES or NO, and then OK. 3. Press EXIT to exit the menu.
Installation Blind Scan 1. Go to main menu ﹥ Installation ﹥Blind Scan 2. Press OK to start scanning. 3. Press EXIT to exit the menu. Transponder Setup 1. Go to main menu ﹥ Installation ﹥ Transponder Setup 2. You can perform the transponder scan [Add/Edit] based on the LNB frequency, LNB power, 22KHz and DiSEqc values stored in the satellite setup for that selected satellite. 3. There are three items you can choose: Add, Edit, Delete. Press ◄/► to choose the item you want to do.
Digital Satellite Receiver DTVS-1B User Guide Installation DisEqC Motor Setup There are two items you can choose: DisEqc1.2 Setup and USALS Setup. a) DisEqC1.2 setup 1. If you have only one Set Top box, but you like to watch all coverage of satellite signal then you need to go for motorized dish which is called DiSEqC1.2. 2.
Installation LEFT/RIGHT key. 3. Goto X - GoTo X option is used to move the motor to specified Dish position. To perform this option - select Dish moving type as GoTo X and enter the Dish position by pressing numeric keys and now press OK key to move the dish to specified position. 4. Advanced - This setup is used to perform the below listed Motor related settings, * DiSEqC 1.2 Enable/Disable - To enable (or) disable the DiSEqC option by pressing OK key.
Digital Satellite Receiver DTVS-1B User Guide Installation Factory Default 1. Go to main menu ﹥ Installation ﹥ Factory Default 2. Press OK, there will be a window to displayed to confirm with you if you want to default all of the settings. Press ▲/▼ to choose YES or NO, and then OK. If you choose YES, there will be a window asking you to enter the password, if you have not set a new password, press 0000; if you have, enter the password that you have set. 3.
System Setup Reset Box Info 1. Go to main menu ﹥ Installation ﹥ Reset Box Info 2. Press OK, there will be a window displayed to confirm with you if you want to set the box information. Press ▲/▼ to choose YES or NO, and then OK. If you choose YES, there will be a window asking you to enter the password, if you have not set a new password, press 0000; if you have, enter the password that you have set. 3. Press EXIT to exit the menu.
Digital Satellite Receiver DTVS-1B User Guide System Setup System Setup Go to Main Menu > System Setup. There will be the following items, such as: Language Setup, OSD Setup, TV Setup, Time Setup, Password Setup, Wakeup Timer. Language Setup 1. Select Language Setup , and press OK to enter into it. 2. Press ▲/▼ to choose the item you want to set. Press ◄/► and OK to select what you would like. There are six languages for OSD item: ENG, FRA, ITA, ESL, DEU, RUS. 3. Press EXIT to exit the menu.
System Setup OSD Setup 1. Select OSD setup, and press OK to enter into it. 2. Press ▲/▼ to choose the item you want to set. Press ◄/► and to select what you would like. 3. Press EXIT to exit the menu. TV Setup 1. Select TV srtup, and press OK to enter into it. 2. Press ▲/▼ to choose the item, and press ◄/► to match with your TV set and press OK. The receiver; can support aspect ratios: 4:3 Letter box, 4:3 full screen, 16:9 3. Press EXIT to exit the menu.
Digital Satellite Receiver DTVS-1B User Guide System Setup Time Setup 1. Select Time setup, and press OK to enter into it. 2. Press ▲/▼ to choose the item, and press ◄/► to choose timer mode, if you select Manual, you can set the date and time with the numeric keys 0~9. 3. Press EXIT to exit the menu. Password Setup 1. Select Password Setup, Press OK to enter into it. 2. Select Lock Type to set the type you want select old password to change the password to a password that you can easily remember.
System Setup Wakeup Timer 1. Select Wakeup Timer, and press OK to enter into. 2. Press ▲/▼ to choose the item, and press ◄/► or numeric keys 0~9 to set Timer., Timer Mode, Service, Date, Start Time, Duration and press OK. 3. Press EXIT to exit.
Digital Satellite Receiver DTVS-1B User Guide Accessories In this menu, there are three submenus: S/W upgrade, Version and Signal Monitoring S/W Upgrade 1. Select S/W upgrade and and press OK to enter it. 2. There will be a window showed “search for S/W upgrade from air is in progress and you will wait for about 20 seconds. Then a menu will be showed to confirm with you if you want to upgrade the software. Press ▲/▼ to choose YES or NO, if you choose YES, the software will be upgraded.
Accessories Version 1. Select Version, and press OK. 2. You can find the version information of your receiver. 3. Press OK or EXIT to exit. Signal Monitoring 1. Go to main menu ﹥ Accessories ﹥ Signal Monitoring 2. You can check the availability of signal, such as signal strength and signal quality by changing these parameters: Satellite name, LNB Low & High frequency, LNB Power, Frequency, Symbol rate, Polarization, 22KHz mode. 3. Press EXIT to exit the menu.
Digital Satellite Receiver DTVS-1B User Guide Country Setup/EPG Country Setup 1. Go to main menu > Country Setup 2. In this menu, there are twenty major areas to choose from: Southern Lakes, Canterbury, Westcoast, Wellington, Wairarapa, Manawatu, Wanganui, Taranaki, Hastings, Napier, Gisborne, Taupo, Bay of Plenty, Rotorua, Waikato, Auckland, Northland, All free channels, Southland and Otago. 3. Press EXIT to exit the menu. EPG 1. Go to main menu > EPG 2.
Troubleshooting If you experience problems with this receiver or its installation, in the first instance please read carefully the relevant sections of this User Manual and this Troubleshooting section.
Digital Satellite Receiver DTVS-1B User Guide Receiver Specifications Item Connectors Power supply Display Others Specification LNB INPUT IF in, connects to your dish antenna LNB OUT IF out, provides a loop out for a second STB TV ANT IN IEC female connector To TV Anlog RF output RS232C Serial port for software upgrade S/PDIF RCA, for SPDIF digital audio output Video RCA, for CVBS video output YCbCr RCA, for component video output L/R x 2 RCA, Analog audio output Input AC 170 - 2
Warranty Please keep your receipt as proof of purchase. This product is warranted for any defect in materials or workmanship for one year after the original date of purchase. This product is for normal domestic and office use only. This warranty does not cover damage from misuse or neglect, accidental damage, vermin in festation, excessive voltages such us lightning or power surges or any alternation that affects the performance or reliability of product.
