Quick Start Guide

ManualsBrandsAvycon ManualsHD Recorders8 Channel HD All-In-One Digital Video Recorder, 12TB

Note: Please read this instruction carefully for correct use of the product and preserve it for reference purposes.

All the examples and pictures used here are for reference only. There may be several technically incorrect places

or printing errors in this manual. The updates will be added into the new version of this manual. The contents of

this manual are subject to change without notice.This device should be operated only from the type of power

source indicatedon the marking label. The voltage of the power must be veriﬁed before using the same.

All-in-One DVR

Quick Start Guide

This series of the product supports 1 SATA hard drive. Please make sure

that the device is powered off before the installation. The pictures of

the installation are only for reference, please take the real object as the

standard.

The interfaces of the rear panels are for reference only.

1. HDD Installation

2. Rear Panel Installation

• Startup

1. Connect the monitor and the power.

2. The device will boot and the power indicator will display blue.

3. A wizard window will pop up.

• Shutdown

Go to “Main Menu” and then select “Shutdown” icon. This will bring up

a shutdown window. The device will shut down by clicking “OK” button.

Then disconnect the power.

3. Startup & Shutdown

4. Login

First connect the camera to the DVR. Then go to Start → Settings

→ Camera → Manage Camera → Signal Access Set to checkmark

the video mode. The actual signals input shall correspond to the

video mode. Please refer to User Manual for details.

5. Analog Camera Connection

After you ﬁnish adding IP cameras, you can see the live images

through the monitor of the DVR. The following will mainly

introduce how to add the IP cameras via LAN/WAN.

6. Network Configuration & Add IP Camera

• LAN

1.Set the network of the DVR. Go to Start → Settings → Network

→TCP/IPv4. Input IP address, subnet mask, gateway, etc. If using

DHCP, please enable DHCP in both the DVR and the router.

2. Go to Start → Settings → Network → Port. Input HTTP port

(the default value is 80), server port (the default port is 6036).

3. Click “Apply” to save the settings.

4. Go to Start → Settings → Camera → Add Camera. The DVR will

automatically refresh the cameras searched. The IPC which

supports the Onvif protocol may be added manually. If the IPC

searched is not in the same local network as the DVR, you should

select the device and click to modify the IP address.

1.Loosen the screws to open the

cover.

2.Screw the screws into the HDD

but not tighten them.

3.Place the HDD onto the bottom

of the machine.

4.Connect the power and data

cables.

5. Turn over the machine and secure

the HDD with the screws.

6. Install back the cover and secure

it with the screws.

Username

Password

admin

Enter Password

Display Password Log In Automatically

Edit Security Question Login Cancel

Mac Ad dres s

IP Ad dres s

Edit IP

19 2 .168 . 1 . 45

25 5 . 255 . 255 . 0

ad m i n

19 2 .168 . 1 . 1

Su bne t Mask

Use rnam e

Gat ewa y

Pa sswor d

OK Cancel

CE :98 :23 :7 5 :35 :22

4.0.0.1.beta1

Version

No.

IP Address

EditPort

Protocol Model

Subnet Mask

192.168.2.45

XXXXXX

255.255.255.0

Quickly Add

Manually Add

Add Camera

Selected: 1/1

Add

Default Password

Remain Bandwidth: 10 / 10 Mb

Cancel

Port

TCP/IPv4

DDNS

E-mail

NAT

IP Address Settings

Obtain an IP address automaticall y

Ethernet Port 1 ( Online )

Obatin DNS server address autom atically

IP Address

Preferred DNS

192 . 168 . 1 . 2

0 . 0 . 0 . 0

192 . 168 . 1 . 1

0 . 0 . 0 . 0

Subnet Mask

Alternate DNS

Gateway

UPnP Network Status

For our HT500A series DVRs, the default username is admin and the

default password is 123456. When starting HT500A series DVR for

the ﬁrst time, you will see a prompt to begin a startup wizard. You can

skip this wizard if you would like, but it will help you conﬁgure basic

settings for your DVR. The wizard may allow you to also change the

default password for better security. If you decide to skip the wizard,

to access the live view and start using your DVR click on the Start

button in the bottom left of the menu bar on the bottom of the

screen and then click on Login and enter in the default password.

Inte rnet

CV BS

DC 12 V

US B

e SATA

LA N

VG A

AU DIO I N

1 5

2 6

3 7

4 8

VI DEO I N

6 8

AU DIO O UT

48 5

GND

COM 2

COM 1

NO2

NO1

531

AL ARM O UT

AL ARM I N

Audio input

Alarm input for connecting sensor

Audio output

Relay output; connect to external alarm

Video input

Connect to high definition display device

Connect to monitor

CVBS output

Ground

Ethernet connector

Connector for USB devices

Connector for e-SATA

Power input

Connect

for

RS485 devices

. A is TX+,B is TX-

AUDIO OUT

ALARM OUT

Name

Description

VIDEO IN

AUDIO IN

ALARM IN

CVBS

GND

VGA

HDMI

LAN

USB

e-SATA

DC12V

RS485

Rear Panel for 8CH

Summary of content (2 pages)

PAGE 1
5. Analog Camera Connection ALARM OUT ALARM IN COM1 NO1 GND 1 3 5 1 3 5 7 3 1 5 7 e SATA CVBS 7 B COM2 NO2 GND 2 All-in-One DVR Quick Start Guide 4 6 8 2 4AUDIO IN6 This series of the product supports 1 SATA hard drive. Please make sure that the device is powered off before the installation. The pictures of the installation are only for reference, please take the real object as the standard.
PAGE 2
5. Checkmark the device you want to add and then click “Add” button. The DVR will automatically refresh the cameras and return to “Edit Camera” interface. “Online” status means connecting the device successfully and you will see the live image. You may select the added device and click button to modify channel, IP address, ect. Edit Camera Signal Access Set TCP/IPv4 Port Camera Name 1 IP Camera 1 2 [A01]Camera1 3 [A02]Camera2 4 [A03]Camera3 5 [A04]Camera4 IP Address Edit Camera Group 192.