Quick Start Guide
Note: Please read this instruction carefully for correct use of the product and preserve it for reference purposes.
All the examples and pictures used here are for reference only. There may be several technically incorrect
places or printing errors in this manual. The updates will be added into the new version of this manual. The
contents of this manual are subject to change without notice.This device should be operated only from the
type of power source indicatedon the marking label. The voltage of the power must be verified before using
the same.
Network Video Recorder
Quick Start Guide
This series of the product supports 1 SATA hard drive. Please make
sure that the device is powered off before the installation. The pictures
of the installation are only for reference, please take the real object as
the standard.
For our HN500 series NVRs, the default username is admin and the
default password is 123456. When starting HN500 series NVR for
the first time, you will see a prompt to begin a startup wizard. You can
skip this wizard if you would like, but it will help you configure basic
settings for your NVR. The wizard may allow you to also change the
default password for better security. If you decide to skip the wizard,
to access the live view and start using your NVR click on the Start
button in the bottom left of the menu bar on the bottom of the
screen and then click on Login and enter in the default password.
1. HDD Installation
2. Rear Panel Installation
1.Loosen the screws to open the cover. 2. Screw two screws into the holes of HDD but
not tighten them.
3. Turn over the machine and place the HDD
with two screws onto the bottom of the case.
Then lock the screws according to the order
of the marks.
5. Connect the power and data cables. 6. Install the cover back and fix it.
4. Install the other three HDDs according to
above-mentioned method.
The interfaces of the rear panel are for reference only.
• Startup
1. Connect the monitor and the power.
2. The device will boot and the power indicator will display blue.
3. A wizard window will pop up.
• Shutdown
Go to “Main Menu” and then select “Shutdown” icon. This will bring
up a shutdown window. The device will shut down by clicking “OK”
button. Then disconnect the power.
3. Startup & Shutdown
4. Login
Username
Password
admin
Login
Enter Password
Display Password Log In Automatically
LoginEdit Security Question Cancel
5. Checkmark the device you want to add and then click “Add”
button. The NVR will automatically refresh the cameras and
return to “Edit Camera” interface.
LAN
US B
1
3
5
7
2
4
6 8 10
9
12
11
14
13
16
15
N
O1
N
O
2
NO
3
NO4
GND
GND
G
N
D
GND
C
O
M
1
COM 2
C
OM3
C
OM4
A BY Z
K/ BP/ Z
AL AR M OU T
AL AR M IN
RS 4 85
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Po E Po r ts
After you finish adding IP cameras, you can see the live images
through the monitor of the NVR. The following will mainly
introduce how to add the IP cameras via LAN/WAN.
5. Network Configuration
• LAN
1. Set the network of the NVR. Go to Start → Settings →
Network → TCP/IPv4. Input IP address, subnet mask, gateway,
etc. If using DHCP, please enable DHCP in both the NVR and
the router.
2. Go to Start → Settings → Network → Port. Input HTTP port
(the default value is 80), server port (the default port is 6036).
3. Click “Apply” to save the settings
4. Go to Start → Settings → Camera → Add Camera. The NVR
will automatically refresh the cameras searched. The IPC which
supports the Onvif protocol may be added manually. If the IPC
searched is not in the same local network as the NVR, you
should select the device and click to modify the IP address.
4.0.0.1 .beta1
Version
1
2
192.168 .1. 20
192.168 .1. 38
XXX80
80
80
XXX
XXX
XXX
3.4.2
3.4.2
255.255 .25 5.0
255.255 .25 5.0
No.
IP Address
EditPort
Protoco l Model
Subnet Ma sk
3
192.168 .2. 45
XXXXXX
255.255 .25 5.0
Quickly Add
Manually Add
Add Camera
Selecte d: 1/3
Add
Default P ass word
Remain Bandwidth: 108 / 120 Mb
Cancel
Mac Addres s
IP Addr ess
Port
CE :98 :23 :7 5 :35 : 22
Edit IP Camera
80
192 .168 . 1 . 45
255 . 255 . 255 . 0
admin
192 .168 . 1 . 1
Subnet Mask
Username
Gateway
Password
OK Cance l
4.0.0.1 .beta1
Version
1
2
192.168 .1. 20
192.168 .1. 38
XXX80
80
80
XXX
XXX
XXX
3.4.2
3.4.2
255.255 .25 5.0
255.255 .25 5.0
No.
IP Address
EditPort
Protoco l Model
Subnet Ma sk
3
192.168 .2. 45
XXXXXX
255.255 .25 5.0
Quickly Add
Manually Add
Add Camera
Selecte d: 1/3
Add
Default P ass word
Remain Bandwidth: 108 / 120 Mb
Cancel
Mac Addres s
IP Addr ess
Port
CE :98 :23 :7 5 :35 : 22
Edit IP Camera
80
192 .168 . 1 . 45
255 . 255 . 255 . 0
admin
192 .168 . 1 . 1
Subnet Mask
Username
Gateway
Password
OK Cance l
4.0.0.1 .beta1
Version
1
2
192.168 .1. 20
192.168 .1. 38
XXX80
80
80
XXX
XXX
XXX
3.4.2
3.4.2
255.255 .25 5.0
255.255 .25 5.0
No.
IP Address
EditPort
Protoco l Model
Subnet Ma sk
3
192.168 .2. 45
XXXXXX
255.255 .25 5.0
Quickly Add
Manually Add
Add Camera
Selecte d: 1/3
Add
Default P ass word
Remain Bandwidth: 108 / 120 Mb
Cancel
Mac Addres s
IP Addr ess
Port
CE :98 :23 :7 5 :35 : 22
Edit IP Camera
80
192 .168 . 1 . 45
255 . 255 . 255 . 0
admin
192 .168 . 1 . 1
Subnet Mask
Username
Gateway
Password
OK Cance l
4.0.0.1 .beta1
Version
1
2
192.168 .1. 20
192.168 .1. 38
XXX80
80
80
XXX
XXX
XXX
3.4.2
3.4.2
255.255 .25 5.0
255.255 .25 5.0
No.
IP Address
EditPort
Protoco l Model
Subnet Ma sk
3
192.168 .2. 45
XXXXXX
255.255 .25 5.0
Quickly Add
Manually Add
Add Camera
Selecte d: 1/3
Add
Default P ass word
Remain Bandwidth: 108 / 120 Mb
Cancel
Mac Addres s
IP Addr ess
Port
CE :98 :23 :7 5 :35 : 22
Edit IP Camera
80
192 .168 . 1 . 45
255 . 255 . 255 . 0
admin
192 .168 . 1 . 1
Subnet Mask
Username
Gateway
Password
OK Cance l
Port
TCP/IPv4
DDNS
E-mail
NAT
IP Address Settings
Obtain an IP address autom ati cally
Ethernet Por t 1 ( Online )
Obatin DNS server a ddr ess automatically
IP Addr ess
Preferred DNS
192 . 168 . 1 . 2
0 . 0 . 0 . 0
192 . 168 . 1 . 1
192 . 168 . 1 . 1
0 . 0 . 0 . 0
Subnet Mask
Alternate DN S
Gateway
UPnP Telnet