Quick Start Guide

ManualsBrandsAvycon ManualsNVR128 Channels 4K UHD Network Video Recorder, 80TB

Table Of Contents

9. Manual Recording

7. UPnP

8. NAT

10. Playback

⑤ Checkmark the device you want to add and then click “Add” button.The

NVR will automatically refresh the cameras and return to “Edit Camera”

interface. “Online” status means connecting the device successfully and

you will see the live image. You may select the added device and click

button to modify channel, IP address, ect.

Versio n

Upgra de

Opera tio n

Display Password

Sync to IPC

Camera Name

Address

Model

Edit Camera

XXX

192 .168 . 1 . 58

admin

XXX

Port

Username

Protocol

Password

IP Camera 3

OKTest Cancel

192.1 68. 1.20IP Cam era 1

192.1 68. 1.38IP Cam era 2

XXX

Onlin e

XXXOffl ine

XXX80

Remai n Ban dwidth: 8 5 / 120 Mb

No. Camer a Nam e

Addre ss

Port

Proto col

Model

Previ ew

Statu s

Edit Camera

Edit Camera Group

Search C amera

192.1 68. 1.45IP Cam era 3

XXXOnlin e

4.1.0 .0

XXX80

►WAN

① Set the network of the NVR. Go to Start → Settings → Network → PPPoE. Input

static IP address or enable PPPoE and then input the user name and password received

from your ISP.

② Go to Start → Settings → Camera. Click “Add Camera” or behind the

column of the search camera and select “Manually Add” to add the IP cameras.

Input IP address, server port, username and password of the IP camera. The IP

camera must be connected over WAN. And here the IP address of the IP camera

must be a WAN IP address.

►NAT Settings

① The NVR shall be powered on and connected to the network.

② Go to Start → Settings → Network → TCP/IP. You can obtain the IP address,

subnet mask and gateway automatically. You can also manually enter them

according to the actual network situation. Please make sure the network

segment is the same as that of the network which is used.

③ Set the preferred or alternative DNS Server. Click “Apply” to save the

parameters.

④ Go to Start → Settings → Network → NAT tab. Enable NAT and select

the NAT Server (The default NAT Server is nat.autonat.com). Click “Apply”

to save the parameters.

nat.auton at.comNAT Server Address

Enable

Visit Address www.autonat.com

Apply

►NAT Access

After finishing the NAT settings, you can input www.autonat.com in the IE

address bar and then press enter to go to the following interface. If you are

the first time to access the NAT, you shall download and install the ActiveX

according to the popup tips. After installing ActiveX successfully, it will

pop the login box.

Before recording, please install and format a HDD. In the live interface

you can see the menu toolbar. Click button to start recording. Click

it again to stop recording. You can also click to check the status of

the recording.

►Instant playback

Click “Instant Playback” in the right-click menu of the camera’s preview

window to select or drag the playback progress bar to change the playback

time to play back the record.

►General playback

Click on the tool bar at the bottom of the live preview interface or click

Start → Playback to go to the playback interface as shown below. You can also

add the playback cameras manually. Click in the playback window to pop

up the “Add Camera” window. Check the cameras in the window and then click

“Add” to add playback camera. The record files of the added playback camera

will be played in the playback interface.

You can use the UPnP function to enable the fast connection of the device to

WAN via a router without port mapping.

① Go to Start → Settings → Network → UPnP, and enable UPnP and then

click “Apply” button to save.

② Enable the UPnP function in the router.

③ Click “Refresh” button to refresh the UPnP status. If the UPnP status were

still “Invalid UPnP” after refreshing it for several times, the port would be wrong.

Please change the mapping type to “Manual” and then click to modify the

port until the UPnP status turns to “valid UPnP”.

HTTP Port

Server Port

6036

80183.17.25 4.19 Valid UPnP

Valid UPnP

Invalid UPn P

6036183 .17. 254. 19

Port Type

Exter nal Po rt

Exter nal Add ress

UPnP Statu s Edit

Port

RTSP Port

554

AutoMap Type

UPnP

NAT

Enable

Refresh Apply

450041000971 A0

Device Serial Number: Click on the menu bar at the bottom of the live

interface to check the serial number or go to Start → Settings → Network →

Network Status to check the serial number of the NVR).

Username: The username of the NVR. The default username is admin.

Password: The password of the NVR. The password is set by yourself when

you configure the wizard for the first time.

Enter Password

Enter Username

Enter device serial number

TCP/IP

Port

PPPoE

DDNS

E-mail

UPnP

NAT

Telnet