AVUE Advanced Video Surveillance G55IR-WB36N Infrared Intelligent Vehicle PTZ Camera User Manual
TABLE OF CONTENT 1. Notice--------------------------------------------------------------------------------------------------------1 2. Performance-----------------------------------------------------------------------------------------2 2.1 PTZ t echnology parameter --------------------- -------------- ------------------------------------------2 2.2 Camera parameter----------- ----------------------------------------- --- - ----------------------------- 2 2.
5.8.2 White balance mode ---------- ---------------- ----- ----------------------------------------26 6. Function setting -------------------------------------------------------------------------------------------27 6.1 Preset ---------------------------- ------- ------- --- ------------------------------------------------------ 27 6.2 Scan -------------- --------------------------------- ------------------------------------------------------ 28 6.
Precaution 1. Precaution Ø Electrical safety Conform to country and local electrical safety standard when using or installing the product. Ø Transportation The PTZ should be protected against extremes of pressure, vibration and humidity during storage installation and transportation. The infrared PTZ camera is transported by integrated packing. Ø Installation of care Please refer to user installation manual when installation.
Performance 2. 1 Technology parameter Setting: Electrical： AC24V Power supply Consumption PTZ + Infrared light(50W) PTZ + Searchlight(100W) Protocol Decoder Built-in Address setting Operation: 360°continuously Tilt rotation Tilt180°，with auto flip Pan0.4～80°/S Rotation speed Tilt0.4～60° /S -40 ~ + 60℃ Environmental humidity 0—95% no compensation Surveillance Physical: Infrared night vision 2.
Performance 2.3 PTZ Performance and Feature The intelligent Pan/tilt was complete new design, compact structure, built-in constant temperature device and rapidly heat dissipation from chip; wiper function can retain full resolution picture in raining day; AMP socket is convenient for installation; Infrared LED range more than 60 meters; Camera rotate flexibly with low noise, wide range capture and certain auto-functions can provide perfect quality of image for customer.
Performance Ø Internal temperature test Set time display ● When the temperature exceeds the limit, the screen will display alarm information. ● When the temperature is under the limit, the PTZ will delay to startup, and when the heat device is heated and got higher than low limit temperature to startup. ● According to the temperature, the fan measures if it is to start or not, and prolong the life of fan.
Function Instruction 3. Function Instruction This passage mainly describes the main function and general principle of intelligence PTZ, and not refer to the concrete operation methods. Different system platform has different operation methods, generally, should according to the system manufactory's operation manual. Please contact dealer to get necessary information, there are some particular requirements and operations under specific condition. 3.
Function Instruction 3. 3 Camera control Ø Magnification control The user can control“Wide/Tele” to adjust zoom far and near of the image by keyboard controller to obtain panoramic image or close view that you need. The PTZ support digital zoom and optical zoom. Ø Focus control System defaults Auto focus. When the lens changes, camera will auto-adjust focus according to the center of the image to get legible image; user can also manually focus to get desire image by operating keyboard “FAR/NEAR”.
Function Instruction Ø Scan The operator can prompt set right limit and left limit in advance by keyboard and menu, so as to make the camera repeatedly scanned between right and left limit at a setting speed. Ø Pattern Pattern is built-in function in camera; the PTZ can record tracks that are no less than 180s, when running pattern, the PTZ moves repeatedly according to the recorded tracks. A PTZ can set up to 4 pattern tours.
System Setting 4. System setting 4. 1 Basic operation 4. 1.
System setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 4. 2 Edit dome label When using a lot of PTZs’systems, in order to identify each PTZ, the systems support title setting. The setting ways as follow： 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. 2、Moving joystick up and down to move the cursor to 【SYSTEM SETTING】, and pressing【OPEN】 to enter into the next menu.
System Setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 4. 3 Display initial information 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. 2、Tilt up/down joystick to 【SYSTEM SETTING】, press 【OPEN】 to enter submenu. 3、Tilt up/down joystick to 【INITIAL INFO】, press【OPEN】 to display initial information as below the left picture .
System setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT SYSTEM SETTING EDIT PTZ LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETUP CLOCK SETTING DOME ADDRESS BACK EXIT DISPLAY SETUP PTZ LABEL OFF PRESET LABEL OFF ZOOM LABEL ON ZONE LABEL OFF DIRECTION LABEL ON TEMPERATURE LABEL OFF TIME LABEL ON DATE LABEL ON BACK EXIT 4.
System Setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 4. 5 Systematic motion control Systematic motion controlling may control a series of canonical movement of the PTZ, and play an important role in controlling the PTZ. 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. 2、Tilt up/down joystick to【SYSTEM SETTING】, press【OPEN】to enter submenu.
System setting 4. 5. 3 Park action MOTION AUTO FLIP ON PROPORTION PAN ON PARK TIME 005 PARK ACTION SCAN POWER UP ACTION AUTO FAN ENABLED 040 TEMP C/F CENT ADVANCE SETTING BACK EXIT This setting allows the PTZ to run an appointed action after it enters vacancy for a few time (1-240minutes). If default sets as 0, it means not to run this action automatically.
System Setting 4.5.6 Advance setting MOTION AUTO FLIP ON PROPORTION PAN ON PARK TIME 005 PARK ACTION SCAN1 POWER UP ACTION AUTO FAN ENABLED 040 TEMP CENT ADVANCE SETTING BACK EXIT ADVANCE SETTING EIS ENABLED N/A PRESET FREEZE N/A HEAD-DOWN ON/OFF DEFOGGER 10 A D J SPEED 100 WIPER IR HEADLIGHT BACK EXIT 1.
System setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 4. 6 Clear and restart 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. 2、Tilt up/down joystick to 【SYSTEM SETTING】, press 【OPEN】to enter submenu. 3、Tilt up/down joystick to 【CLEAR】, press 【OPEN】to enter submenu, as left picture shows.
System Setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 4.7 Password set 1. The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. 2. Operate the joystick up and down, move the cursor to 【SYSTEM SETTING】 , press 【OPEN】 to call the submenu. 3. Operate the joystick up and down , move the cursor to 【PASSWORD SETUP】, press 【OPEN】 to call the submenu. Please refer to the left picture. 4.
System setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 4.8 Time set 1. The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. 2. Operate the joystick up and down, move the cursor to 【SYSTEM SETTING】 , press 【OPEN】 to call the submenu. 3. Operate the joystick up and down, move the cursor to 【CLOCK SETTING】 , press【 OPEN 】to call the submenu. Please refer to the left picture. 4.
System Setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 4.9 DOME Address Setting 1.The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. 2.Tilt up/down the joystick and move the cursor to【SYSTEM SETTING】, press【OPEN】 to enter submenu. 3.Tilt up/down the joystick and move the cursor to【DOME ADDRESS】, press【OPEN】 to call dome parameter setting menu . S/N : Series No.
Camera setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 5. Camera setting 5. 1 Zoom speed 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds.
Camera Setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 5. 2 Digital zoom control 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds.
Camera setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 5. 3 Back light compensation 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. 2、Operate joystick, move the cursor to 【CAMERA SETTING】 to enter submenu.
Camera Setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 5. 4 Slow shutter control 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. 2、Operate joystick, move the cursor to【CAMERA SETTING】 to enter submenu.
Camera setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 5. 5 Line sync control 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. 2、Operate joystick, move the cursor to 【CAMERA SETTING】, press 【OPEN】 to enter submenu. 3、Operate joystick, move the cursor to 【LINE SYNC】; press 【OPEN】, tilt up/down joystick to set line sync.
Camera Setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 5. 7 IR cut filter 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. 2、Operate joystick, move the cursor to 【CAMERA SETTING】 to enter submenu.
Camera setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 5. 8 Advance setting 2 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. 2、Operate joystick, move the cursor to 【CAMERA SETTING】 to enter submenu. 3、Operate joystick, move the cursor to 【ADVANCE SETTING2】; press 【OPEN】 to enter submenu, as left picture shows; 5. 8 .
Camera Setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 5. 8. 2 White balance mode System supports 【AUTO】 、indoor mode 【INDOOR】 、outdoor mode 【OUTDOOR】 、auto track mode 【ATW 】 、single mode 【OPW】 、 【OPT】 mode、manual mode【MANUAL】 and kinds of white balance modes, etc. Detail setting as follow: 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds.
Function setting 6. Function setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT FUNCTION SETTING PRESETS SCAN PATTERNS TOUR ZONES TIME RUNNING BACK EXIT 6. 1 Preset 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. Click each command to enter“ preset menu” according to the order of the left picture.
Function setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 6. 2 Scan Scan is that preset two points , then the camera repeatedly scan between the two points at a stable speed, the same magnification and pan. A dome has four scan tour. 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. click menu to enter “scan” menu, as the left picture shows.
Function setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 6. 3 Pattern Pattern is built-in function in camera; the PTZ can record tracks that are no less than 180s. (A series of pan/tilt controlling and lens controlling command). A PTZ may set up to 4 pattern tours. 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds.
Function setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 6. 4 Tour Tour is the built-in function in the PTZ, it will arrange the presets into the queue of auto-tour, and can set how long it will park at preset. Operate auto-tour is a process of incessantly transfer each preset. One tour can store 32 presets at most. 1、 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds.
Function setting 6. 5 Zone MAIN MENU A PTZ may be set up to 8 zones; the regional scene can't be overlapped. SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT User can set label for each zone. When setting【ZONE LABEL】 as ON, the PTZ will display zone label as it runs some zone. It is convenient to know the zone that the camera shoots by setting zone label. 1、The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds.
Function setting 6 . 6 Time running MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT User can set the time of preset, scan, tour and pattern. 1.Call 95 preset or call 9 preset twice within 3 seconds to enter into the main menu. 2. Operate the joystick, move the cursor to 【FUNCTION SETTING】 , press 【OPEN】 to call the submenu. 3. Operate the joystick, move the cursor to 【TIME RUNNING】 , press 【OPEN】 to enter into the menu setting.
Privacy zone masking MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 7. Privacy zone masking Privacy function can show someone piece of regional shielding while protecting. For example, protect the window of bedroom or ATM of bank. A PTZ can set up to 24 privacy windows.(Masking setting function is relative with the model of camera module. The masking numbers will be different according to the different cameras.
Alarm Function MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT ALARMS RESUME OFF SEQUENCE 002 RESET DELAY 020 ALARM CONTACT N/C ALARM SETTING ARM SETTING BACK EXIT ALARM SETTING ALARM NUMBER 001 ALARM ACTION TOUR ACTIVATE AUX NONE ALARM PRIORITY HIGH BACK EXIT 8. Alarm function The PTZ may connect with 7 alarm input, 2 alarm output, and support alarm linkage.
Alarm Function MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT 3.ARM Setting 1. Call 95 preset or call 9 preset twice within 3 seconds and then input the password to enter the main menu. 2. Operate the joystick up and down, move the cursor to 【ALARMS 】 , press 【OPEN】 to call the submenu. 3. Operate the joystick up and down, move the cursor to 【ARM SETTING】 , press 【OPEN 】to call the submenu. Please refer to the left picture. 4.
Set Language MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT LANGUAGE LANGUAGE BACK EXIT 36 ENGLISH 9.Set Language 1. Call 95 preset or call 9 preset twice within 3 seconds and then input the password to enter the main menu. 2. Operate the joystick up and down, move the cursor to 【LANGUAGE】 , press 【OPEN】 to call the submenu.
Appendix 10 Appendix 10. 1 Menu Index SYSTEM SETTING CAMERA SETTING EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETUP CLOCK SETTING DOME ADDRESS BACK EXIT ZOOM SPEED HIGH DIGITAL ZOOM OFF BLC MODE OFF SLOW SHUTTER OFF LINE SYNC N/A WDR MODE N/A ADVANCE SETTING 1 ADVANCE SETTING2 BACK EDIT DOME LABEL IR CUT FILTER AUTO IR CUT ON TIME N/A IR CUT OFF TIME N/A THRESHOLD 10dB FLIP OFF MIRROR OFF MAX GAIN 08dB EXPOSURECOMP OFF BACK EXIT INITIAL INFO S/N:8D SAD7B26200 000 FIRMWARE V1.
Appendix 10.2 24VAC Wire Diameter and Transmission Distance Comparison chart The transmission distances listed below are farthest ones recommended for each giving wire diameter when the 24VAC voltage loss ratio is below 10%(for equipment powered by AC, the allowed maximum voltage loss ratio is 10%). The rating power of PTZ is 50W, need a wire with a minimum diameter of 1.0mm. Wi re Diameter (mm) 0 .8 00 1. 0 00 1 .2 50 2.
Appendix 10.3 Domestic and Abroad Wire Gauge Conversion Chart Bare Wire Diameter Metric Size(mm) AWC (Apprximate) SWC (Approximate) Bare Wire Cross-Sectional Area（mm 2） 0.0 50 43 47 0. 0 0196 0.0 60 42 46 0.0 0283 0.0 70 41 45 0.0 0385 0.0 80 40 44 0.0 0503 0.0 90 39 43 0.0 06 36 0.0 10 38 42 0.0 0785 0.1 10 37 41 0.0 09 50 0.1 30 36 39 0.0 13 27 0.1 40 35 0.1 60 34 0.1 80 33 0.2 00 32 0.2 30 31 0.2 50 30 33 0.0 49 09 0.2 90 29 31 0.0 6605 0.
Appendix 10. 4 Rs485 Bus Basic Knowledge Ø Characteristics of Rs485 Bus Ø The connection of 120Ω termination resistor: As specified by Rs485 standard, Rs485 Bus is of half-duplexed data transmission cables with characteristic impedance as 120Ω. The maximum load capacity is 32 unit loads (including main controller and controlled equipment.) Connection mode for 120 Ω resistance of equipment terminal. Setting connection of terminal resistance 120Ω in the base cover. (Refer to Picture 10-4.
Appendix Ø Problems in practical connections In some circumstances user adopts a star co- In such circumstances the factory recommends the usage of RS485 distributor. The distributor can nfiguration in practical connection. The termina- change the star configuration connection to the mode tion resistors must be connected to the two equi- of connection stipulated in the RS485 standards. pment 1# and 5# in Picture 10-4.4.
Appendix 10. 5 DIP switch setup Open base, there are two code switches with 10. 5. 2 Protocol setup（SW2） 8 digits, SW1and SW2. SW1 is for setting of PROTOCOL PTZ ID; SW2 is for settings of control protocol, FACTORY baud rate, terminal resistance connect. SW2 SW1 Picture 10-5.
Appendix ID S w i t c h n u m b e r (Sw1) (Bit) 1 2 3 4 5 6 7 8 ID S w i t c h n u m b e r (Sw1) (Bit) 1 2 3 4 5 6 7 8 Factory defaults set as debug address 0 0 0 0 0 0 0 0 34 0 1 0 0 0 1 0 0 1 1 0 0 0 0 0 0 0 35 1 1 0 0 0 1 0 0 2 0 1 0 0 0 0 0 0 36 0 0 1 0 0 1 0 0 3 1 1 0 0 0 0 0 0 37 1 0 1 0 0 1 0 0 4 0 0 1 0 0 0 0 0 38 0 1 1 0 0 1 0 0 5 1 0 1 0 0 0 0 0 39 1 1 1 0 0 1 0 0 6 0 1 1 0 0 0 0 0 40 0 0 0 1 0 1 0 0 7 1 1 1 0 0 0 0 0 41 1 0 0 1 0 1 0 0 8 0 0 0 1 0 0 0 0 42
Appendix ID 44 Switch number (Sw1) Switch number (Sw1) (Bit) 1 2 3 4 5 6 7 8 ID 68 0 0 1 0 0 0 1 0 102 0 1 1 0 0 1 1 0 69 1 0 1 0 0 0 1 0 103 1 1 1 0 0 1 1 0 70 0 1 1 0 0 0 1 0 104 0 0 0 1 0 1 1 0 71 1 1 1 0 0 0 1 0 105 1 0 0 1 0 1 1 0 72 0 0 0 1 0 0 1 0 106 0 1 0 1 0 1 1 0 73 1 0 0 1 0 0 1 0 107 1 1 0 1 0 1 1 0 74 0 1 0 1 0 0 1 0 108 0 0 1 1 0 1 1 0 75 1 1 0 1 0 0 1 0 109 1 0 1 1 0 1 1 0 76 0 0 1 1 0 0 1 0 110 0 1 1 1 0 1 1 0 77 1 0 1 1 0 0 1 0 111 1 1 1 1 0
Appendix ID Switch number (Sw1) (Bit) 1 2 3 4 5 6 7 8 ID Switch number (Sw1) (Bit) 1 2 3 4 5 6 7 8 136 0 0 0 1 0 0 0 1 170 0 1 0 1 0 1 0 1 137 1 0 0 1 0 0 0 1 171 1 1 0 1 0 1 0 1 138 0 1 0 1 0 0 0 1 172 0 0 1 1 0 1 0 1 139 1 1 0 1 0 0 0 1 173 1 0 1 1 0 1 0 1 140 0 0 1 1 0 0 0 1 174 0 1 1 1 0 1 0 1 141 1 0 1 1 0 0 0 1 175 1 1 1 1 0 1 0 1 142 0 1 1 1 0 0 0 1 176 0 0 0 0 1 1 0 1 143 1 1 1 1 0 0 0 1 177 1 0 0 0 1 1 0 1 144 0 0 0 0 1 0 0 1 178 0 1 0 0 1 1 0 1 145 1 0
Appendix ID 46 Switch number (Sw1) (Bit)1 2 3 4 5 6 7 8 ID Switch number (Sw1) (Bit) 1 2 3 4 5 6 7 8 204 0 0 1 1 0 0 1 1 238 0 1 1 1 0 1 1 1 205 1 0 1 1 0 0 1 1 239 1 1 1 1 0 1 1 1 206 0 1 1 1 0 0 1 1 240 0 0 0 0 1 1 1 1 207 1 1 1 1 0 0 1 1 241 1 0 0 0 1 1 1 1 208 0 0 0 0 1 0 1 1 242 0 1 0 0 1 1 1 1 209 1 0 0 0 1 0 1 1 243 1 1 0 0 1 1 1 1 210 0 1 0 0 1 0 1 1 244 0 0 1 0 1 1 1 1 211 1 1 0 0 1 0 1 1 245 1 0 1 0 1 1 1 1 212 0 0 1 0 1 0 1 1 246 0 1 1 0 1 1 1 1 213
Warnings 11.Installation 11.1 Caution l Please refer to user manual before installation. l Power: AC 220V/110V-AC24V, for actual needs, please refer to label of product. l Precise optical and electronic parts inside of product. Avoiding severe press, hard vibration etc non-correct operation methods, which may cause damage to product when transportation and installation. l Please do not disassemble parts inside of product at random, which may cause negative influence on use of product.
Warnings 11. 3 Lightning Proof and Surge Proof This product uses TVS lightning Proof technology, can prevent from the damage of the equipment caused by kinds of pulse signal such as instant lightning strike of power below 4000V, the surge and so on. At the same time, you must adopt the essential protective measure according to the actual situation regarding outdoor installation under the guarantee electricity security. (Refer to chapter 1.3 Distributing the line in security) 11.
Installation Introduction 11.6 Structure Introduction The pan/tilt camera has five parts: main body, camera protection shield, LED protection shield, pedestal and pedestal pad. DIP switch setup inside pedestal; and original integrated packing. Main body Camera protection LED protection shield Pedestal up cover Pedestal down cover Pedestal pad Picture11.6-1 11.7 Basic Size graph 411 210 161 Picture11.
Installation Introduction 11.8 Installation Stand-up mount，top-dowm mount and wall mount are available for this product, which are suitable for different installation environment. Because this product is integrated package, please set parameters of baud rate, control protocol as well as PTZ IP address by setting switch number before any installation. Please refer to “setting of switch number” in appendix. 11.8.2 Top-down Mounting (Non standard setting) 1.
Installation Introduction Please make video cable, power cable, control cable and alarm cable penetrated the bracket, and fixed the bracket stably. Keep enough length of cables: Video cable should be kept 50 mm out of the bracket , and other cables should be kept 80-100 mm from the bracket. 1 2 3 4 5 6 Red Yellow Black Red “AC24V+ ” Black “AC24V-” 1. Al arm terminal 2 2. Video connector 3. Al arm terminal 1 4. RS485 terminal 5. Power supply terminal 6.
Maintenance 12.Maintenance service terms 1. Range of warranty ● The product will be maintained free for one year. ● The product will be obtained the free maintenance service if the same malfunction appears again within three months. ● Malfunction of products caused by force majeure (such as war, earthquake, lightning strike and so on ), abuse, non-standard operation, change of construction, non-normal wear or accident are non-free of warranty.
AVUE 1180 MIRALOMA WAY SUITE C SUNNYVALE, CA 94085 WWW.AVUEINC.COM 408.481.9355; INFO@AVUEINC.COM Intelligence Heavy-duty PTZ Camera User Manual Version V2.11.
