An Aviation Technologies Company Avtech Corporation 3400 Wallingford Ave. North Seattle, WA 98103-9041 www.avtcorp.
File Last Saved: April 16, 2001 (3:20PM) CSD-714 SELCAL INSTALLATION AND OPERATION MANUAL Avtech Part Numbers 1200008-000, -001, -002, & -003 MANUAL PART NUMBER 0200013-000 PROPRIETARY RIGHTS NOTICE THIS DATA IS PROPRIETARY TO AVTECH CORP. DISCLOSURE, REPRODUCTION, OR USE OF THIS DATA FOR ANY PURPOSE IS NOT AUTHORIZED WITHOUT WRITTEN PERMISSION FROM AVTECH CORP.
CSD-714 Installation and Operation Manual CHANGE RECORD REV PAGE DESCRIPTION 1 Cloned from Coltech document 0200013-000 Rev C. All textual references to Coltech and formatting has been changed to Avtech where possible. This component maintenance manual may contain references to Coltech drawings and document numbers.
CSD-714 Installation and Operation Manual SERVICE BULLETIN RECORD Service Bulletin Date Issued Model Effected Subject 1 Seattle, WA USA 23-21-01 Rev 1 June 1995 Page II
CSD-714 Installation and Operation Manual LIST OF EFFECTIVE PAGES Section Page Date 1 Seattle, WA USA 23-21-01 Rev 1 June 1995 Page III
CSD-714 Installation and Operation Manual TABLE OF CONTENTS PAGE TITLE DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION . . . . . . . . . .
CSD-714 Installation and Operation Manual DESCRIPTION The CSD-714 SELCAL DECODER is a rack mounted, 16 tone decoder for the ICAO and ARINC standard SELCAL system, as defined in RTCA paper DO-93. It is available in both two channel (-001, -003) and five channel (-000, -002) versions. It has independent inputs for up to five radios, depending on version, to drive up to five decoder channels.
CSD-714 Installation and Operation Manual OPERATION Pilot operation of the CSD-714 is limited to resetting it after a call and performing a self-test. Normal Operation There are several installation options concerning how the annunciator lamps and audio annunciation work, as well as how the unit is reset after a call. The lamps may be connected to either be on steady or to flash when a call is received, and the audio annunciator may either ring once, ring repeatedly, or not at all.
CSD-714 Installation and Operation Manual SPECIFICATIONS Model Number: CSD-714 Avtech Part Numbers: 1200008-000 (5 channel, standard self-test) 1200008-001 (2 channel, standard self-test) 1200008-002 (5 channel, auto-reset self-test) 1200008-003 (2 channel, auto-reset self-test) Certified to TSO: C59 Conforms to RTCA Spec: DO-93 as amended.
CSD-714 Installation and Operation Manual Mating Connector: ARINC 600 style, size 1 with blank cavity A, Middle insert Arrangement 01 (60 pins), Bottom insert Arrangement 03 (2 coax, 2 size 16 pins, 1 size 12 pin). Tone Inputs: Two or five inputs, transformer coupled. Each input is nominally 10,000 ohms input impedance. Input Tone Level: 0.1 VMS to 3.2 VMS Tone Frequency Tolerance: Normal operation with tones less than 0.3% off frequency.
CSD-714 Installation and Operation Manual Power-On Self Test: Unit checks for valid decode code strapping upon power-on and will latch all annunciators on if invalid. INSTALLATION The CSD-714 is intended for mounting in the radio equipment bay of an aircraft and due to its wide operating temperature range does not need to be in a temperature controlled environment. Although the CSD-714 is equipped to monitor two or five inputs depending on version, it is not necessary to use all channels.
CSD-714 Installation and Operation Manual There is no charge for a code assignment at this time. This code is assigned to the USER and does NOT transfer with the aircraft when it is sold. INSTALLATION TESTING The following tests should be performed to verify the installation in the airplane is operating properly: 1. Apply power to the unit and press the SELF-TEST button to initiate a SELF-TEST.
CSD-714 Installation and Operation Manual NOTES FOR INSTALLATION FIGURES Note 1 - DECODE PROGRAMMING Programming the CSD-714 to respond to a selective call is done by connecting the code selection pins on the rear connector to the CODE SELECT RETURN pin on the rear connector (Pin MP9B). The SELCAL code is composed of four letters. For instance a code might be FJ-LQ. The order of the letters within a group of two is not critical, however it is customary to place them in alphabetical order.
CSD-714 Installation and Operation Manual If manual reset is desired, they may all be tied together and grounded through a normally open, momentary contact switch. The SELF-TEST input (Pin MP3D) is activated by grounding it momentarily. All of these inputs are considered grounded when the voltage on the pin is less than 3.5 volts and are open when it is above 8 volts. Internally they are connected to 10 VDC through a 4700 ohm resistor and will source approximately 2 milliamps when grounded.
CSD-714 Installation and Operation Manual If the squelched audio output of the VHF is used, care must be taken to keep the audio input to the CSD-714 within rating. The frequency response of the output must be such that the difference in output level at any two frequencies between 300 and 1500 Hz is less than 3 dB. A 20 dB attenuator may be required to reduce the audio level as referenced at the beginning of this section. Do not use audio from cockpit volume controls as input to the CSD-714.
CSD-714 Installation and Operation Manual Figure 1 - Wiring Diagram 1 Seattle, WA USA 23-21-01 Rev 1 June 1995 Page 10
CSD-714 Installation and Operation Manual Figure 2 - Outline Drawing 1 Seattle, WA USA 23-21-01 Rev 1 June 1995 Page 11
CSD-714 Installation and Operation Manual Code Letter Position First Second Third Fourth J1 Pin MP10C MP11C MP13C MP15C MP10D MP11D MP13D MP15D Code Letter A B C D E F G H MP10B MP11B MP13B MP15B MP10A MP11A MP13A MP15A J1 MP10, MP11, MP13, MP15 Pin Coding DCBA 0001 0010 0011 0100 0101 0110 0111 1000 J K L M P Q R S DCBA 1001 1010 1011 1100 1101 1110 1111 0000 0 represents a connection to the CODE SEL RETURN, Pin MP9B, or ground. 1 represents no connection to this pin.
CSD-714 Installation and Operation Manual Figure 4 - 20 dB Attenuator 1 Seattle, WA USA 23-21-01 Rev 1 June 1995 Page 13
CSD-714 Installation and Operation Manual Figure 5 - Annunciator Output Circuits 1 Seattle, WA USA 23-21-01 Rev 1 June 1995 Page 14
