Quick Start Guide
Table Of Contents
- Quick Installation Guide
- 1. Introduction
- 2. Safety Instructions
- 3. General Guidelines
- 4. Features
- 5. Installing the Hard Disk Drive (HDD)
- 6. User Interface
- 7. Hardware overview
- 8. Connection and Setup
- 9. Basic Operation
- 10. Push Video Configuration
- 11. Mobile Surveillance via EagleEyes
- 12. Setting Up Push Video
- 13. Set flow counting – virtual fence – one-way pass
- 14. Technical Specifications
- Korte handleiding
- 1. Inleiding
- 2. Veiligheidsinstructies
- 3. Algemene richtlijnen
- 4. Eigenschappen
- 5. De hard disk drive (HDD) installeren
- 6. Gebruikersinterface
- 7. Overzicht hardware
- 8. Aansluiting en instelling
- 9. Basisfuncties
- 10. Push Video-configuratie
- 11. Mobiele bewaking via EagleEyes
- 12. Push Video-configuratie
- 13. Mensentelling - virtuele muur - mensenstroom
- 14. Technische specificaties
- Guide d'installation rapide
- 1. Introduction
- 2. Consignes de sécurité
- 3. Directives générales
- 4. Caractéristiques
- 5. Installer le disque dur (HDD)
- 6. Interface utilisateur
- 7. Aperçu du matériel
- 8. Connexion et configuration
- 9. Fonctionnement de base
- 10. Configurer la fonction push video
- 11. Surveillance mobile via EagleEyes
- 12. Configurer la fonction push video
- 13. Comptage de personnes - barrière virtuelle - flux humain
- 14. Spécifications techniques
- Guía rápida
- 1. Introducción
- 2. Instrucciones de seguridad
- 3. Normas generales
- 4. Características
- 5. Instalar el disco duro (HDD)
- 6. Interfaz de usuario
- 7. Descripción
- 8. Conexión y configuración
- 9. Funciones utilizadas frecuentemente
- 10. Configurar la función de notificación Push Video
- 11. Vigilancia a distancia por el móvil con EagleEyes
- 12. Configurar la notificación Push Video
- 13. Contador de personas – barrera virtual – flujo de personas
- 14. Especificaciones
- Schnelleinstieg
- 1. Einführung
- 2. Sicherheitshinweise
- 3. Allgemeine Richtlinien
- 4. Eigenschaften
- 5. Die Festplatte installieren (HDD)
- 6. Benutzeroberfläche
- 7. Beschreibung
- 8. Anschluss und Konfiguration
- 9. Häufig benutzte Funktionen
- 10. Push Video-Konfiguration
- 11. Fernüberwachung über EagleEyes
- 12. Push Video einstellen
- 13. Personenzählung – virtuelle Mauer – Flusskontrolle
- 14. Technische Daten
- Guia rápida para instalação
- 1. Introdução
- 2. Instruções de segurança
- 3. Normas gerais
- 4. Características
- 5. Instalação da drive de disco rígido (HDD)
- 6. Interface do utilizador
- 7. Visão do hardware
- 8. Instalação e ligação
- 9. Utilização básica
- 10. Configuração da função push vídeo
- 11. Vigilância móvel através do EagleEyes
- 12. Configurar o envio de notificações
- 13. Configure a contagem de fluxo – barreira virtual – passagem numa direcção
- 14. Especificações
DVR16H2
V. 01 – 28/03/2013 5 ©Velleman nv
Notes:
It is not recommended to use a green hard disk in this device. For a list of compatible hard disks, please
refer to the appendices in the full user manual.
It is recommended to clear all data on a new hard disk after the DVR is powered on, and to set the date
and time correctly to make sure that recorded data are not mixed with older data. For details on clearing all
data, refer to Clearing the Hard Disk.
Refer to the illustrations on page 2 of this manual.
There are two hard disk brackets.
1. Loosen the screws on the top cover of the DVR and open it.
2. To install a hard disk in the first bracket: first remove the bracket. Make sure the PCB side of the hard disk
is facing up. Then align the screw holes of the bracket with the screw holes of the hard disk, and fasten the
hard disk to the bracket. Connect the power and data bus connectors to the hard disk. Replace the bracket
in the DVR.
3. To install a hard disk in the second bracket: first connect the power and data bus connectors to the hard
disk. Make sure the PCB side of the hard disk is facing up. Then align the screw holes of the bracket with
the screw holes of the hard disk, and fasten the hard disk to the bracket.
4. When the hard disk is installed, close the top cover and fasten it with the screws.
6. User Interface
Refer to the illustrations on page 2 of this manual.
6.1 DVR Access
1. Connect a USB mouse (not incl.) to the mouse port on the DVR front panel, and check if there is a mouse
icon on the screen, indicating the USB mouse is detected properly.
2. Move your mouse to enter the DVR password with the password keypad. The default user name and
password are both admin.
The status will change from (key lock) to (unlock).
Note: You can configure four different user levels with different access privileges in the main menu
(SYSTEM) > ACCOUNT. For more information, refer to User Creation further in this manual.
6.2 Live Page
1. system time
2. DVR status bar
3. available HDD capacity
4. channel status bar
DVR Status
key lock
key unlock
overwrite on
overwrite off
internet disconnected
internet connected
local connection
USB mouse connected
USB flash drive/device connected
no USB device connected