FRITZ!Box 7272 www.avm.de © AVM GmbH · Alt-Moabit 95 · 10559 Berlin · Telefon 030 39976-0 · info@avm.
Table of Contents Security and Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Handling the FRITZ!Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Conventions in the Manual . . . . . . . . . . . . . . . . . . . . . . 11 1 The FRITZ!Box 7272 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2 Ports, Interfaces, Buttons and LEDs . . . . . . . . . . . .
7 The FRITZ!Box User Interface . . . . . . . . . . . . . . . . . . . . . 33 7.1 7.2 7.3 Opening the User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Overview: FRITZ!Box at a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Standard View and Advanced View . . . . . . . . . . . . . . . . . . . . . . . . . 35 8 Using System Functions of the FRITZ!Box . . . . . . . . . . . 36 8.1 8.2 8.3 8.4 8.5 8.6 Diagnostics: Checking FRITZ!Box Functions. . . . . . . .
12 Password Protection: Using FRITZ!Box Safely . . . . . . . . 59 12.1 12.2 12.3 12.4 12.5 Login with Password: FRITZ!Box Procedures . . . . . . . . . . . . . . . . . . 59 Using a FRITZ!Box Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Using FRITZ!Box Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Forgot Password—What to Do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Mode “No login” . . . . . . . . . . . . . . . . . . . . .
16 FRITZ!Box as a Telephone System . . . . . . . . . . . . . . . . 111 16.1 16.2 16.3 16.4 16.5 16.6 16.7 16.8 16.9 16.10 16.11 Telephone Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 Call List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Answering Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Fax Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21 Assigning FRITZ!Box Name . . . . . . . . . . . . . . . . . . . . . . 155 22 Controlling Smart Home Devices . . . . . . . . . . . . . . . . . 156 23 Configuring Internet Access for Guests . . . . . . . . . . . . 157 23.1 23.2 23.3 Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 Wireless Guest Access: Private Hotspot . . . . . . . . . . . . . . . . . . . . . 157 Configuring Guest Access on the LAN 4 Port . . . . . . . . . . . . . . . . .
28 Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 28.1 28.2 28.3 28.4 28.5 Documentation on the FRITZ!Box . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Information in the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Feedback on FRITZ!Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 Assistance from the Support Team . . . . . . . . . . . . . . . . . . . . . . . . . 183 Manufacturer’s Warranty . . . . . . . .
Security and Handling Before installing and using the FRITZ!Box, please read the following security and handling instructions. Safety Instructions Before connecting the FRITZ!Box 7272, observe the following security instructions in order to protect yourself and the FRITZ!Box from harm. • Overloaded outlets, extension cords and power strips can lead to fires or electric shocks. – Avoid using sockets strips and extension cords if at all possible.
• The base of the FRITZ!Box can heat up during normal operation. This heat can cause damage to heat-sensitive surfaces. – Do not place the FRITZ!Box on heat-sensitive surfaces. • During electrical storms, lightning and electrical surges present a danger to connected electrical devices. – Do not install the FRITZ!Box during an electrical storm. – During a storm, disconnect the FRITZ!Box from the power supply and from the DSL line.
FRITZ!Box 7272 • If you would like to establish wireless connections between the FRITZ!Box and the computer, position the FRITZ!Box at a central location. • Make sure to keep sufficient distance from potential sources of interference like microwave devices or electric devices with large metal housings.
Conventions in the Manual This manual uses the following symbols and emphases: This symbol marks useful hints and tips. This symbol indicates important instructions that must be observed to avoid malfunctions. • Quotation marks designate elements and features in the user interface and paths. Example Select the “Home Network / Smart Home” menu and then click “Register New Device”. • Pointed brackets mark wild cards. Example Press the keys sr. stands for a keyboard sequence.
The FRITZ!Box 7272 1 The FRITZ!Box 7272 Welcome! We are pleased you decided on a FRITZ!Box. The FRITZ!Box 7272 is the hub of your home network, connecting your computers and network devices with the Internet. You can operate the FRITZ!Box as an Internet router on a DSL line. The FRITZ!Box is equipped with ports for computers, telephones and USB devices and supports the wireless technologies WLAN and DECT.
Ports, Interfaces, Buttons and LEDs 2 Ports, Interfaces, Buttons and LEDs This chapter describes the ports, interfaces, buttons and LEDs of the FRITZ!Box. 2.1 Ports and Interfaces DSL ISDN analog USB 2.
Ports and Interfaces • LAN 1—LAN 4 4 Ethernet ports for connecting computers and other network devices like game consoles and network hubs LAN 1—LAN 2: gigabit Ethernet (10/100/1000 Base-T) LAN 3—LAN 4: Ethernet (10/100 Base-T) • USB USB 2.0 port for connecting USB devices like printers or storage media • Wireless access point Integrated wireless access point for connecting to wireless LAN devices that use the radio standard IEEE 802.11b, IEEE 802.11g or IEEE 802.11n in the 2.
Buttons 2.2 Buttons The FRITZ!Box has two buttons on the top of the housing. WLAN WPS Info WLAN Festnetz Internet WLAN WPS Power / DSL Powe DECT DECT FRITZ!Box buttons Button Functions “WLAN” Button • • Switch wireless LAN of the FRITZ!Box on and off Establish a wireless LAN connection using WPS, see Establishing a Wireless LAN Connection Using WPS from page 29 “DECT” Button FRITZ!Box 7272 • Register cordless telephones with the FRITZ!Box; see page 53.
LEDs 2.3 LEDs The FRITZ!Box 7272 has five LEDs, which flash or light up to display various connection statuses and events.
Before You Connect the FRITZ!Box 3 3.1 Before You Connect the FRITZ!Box • • See the information on Security and Handling on page 8. • Make sure that the requirements for operating the FRITZ!Box have been met; see page 17. Check the contents of your FRITZ!Box package. See page 17 to find out what is included in the package. Contents of the FRITZ!Box Package • • • • • • • 3.
Requirements for Operation • for the wireless LAN connection to tablets, smartphones and computers: Tablets, smartphones or computers that support wireless LAN compliant with IEEE 802.11n, IEEE 802.11g or IEEE 802.11b. Computers that do not have wireless LAN integrated can be equipped with wireless LAN support by installing a wireless LAN device, like a FRITZ!WLAN USB Stick, for instance.
Connecting the FRITZ!Box 4 4.1 Connecting the FRITZ!Box • Before you connect the FRITZ!Box, read the instructions on Security and Handling on page 8. • • • Connect the FRITZ!Box to the power supply. Connect the FRITZ!Box to your Internet connection. Connect the FRITZ!Box to your telephone line. Connecting to Electrical Power r/ we Po L DS et er n Int ed Fix e Lin DE CT o Inf DEC T WLA N WPS LAN 4 LAN 3 LAN 2 LAN 1 DSL/TEL FON 1 Power FON S0 FON 2 Connecting to the power supply 1.
Connecting to the Internet 4.2 Connecting to the Internet The FRITZ!Box can be connected using various types of Internet connections: • • • • DSL line Internet cable access using a cable modem Internet via mobile network using a UMTS/HSPA modem Internet connection of another router Connecting to a DSL Line How to connect the FRITZ!Box depends on the type of your line. Line Sockets DSL line with landline Connecting the FRITZ!Box Read the instructions on page 21.
Connecting to the Internet Connecting to a DSL Line with a Landline r/ we Po L DS ern Int et L ed Fix ine DE CT o Inf DEC T WPS FON 2 N FON 1 DSL/TEL WLA LAN 2 LAN 1 LAN 4 LAN 3 Power FON S0 Connecting to the DSL splitter If you have a DSL line and a telephone line, then connect the FRITZ!Box as follows: 1. Connect the long end of the DSL/telephone cable to the socket on the FRITZ!Box labeled “DSL/TEL”. 2.
Connecting to the Internet Connecting to the IP-based DSL Line wer Po SL /D et ern Int ne d Li Fixe DEC T o Inf T WPS FON 2 N FON 1 WLA DSL/TEL LAN 2 DEC LAN 1 LAN 3 Power LAN 4 FON S0 Connecting to the DSL line If you have a DSL line without a connection to the landline telephone network (also known as IP-based or direct access), then connect the FRITZ!Box as follows: 1. Connect the longer end of the DSL cable to the socket on the FRITZ!Box labeled “DSL/TEL”. 2.
Connecting to the Internet Connecting to the Cable Junction With an additional cable modem you can also use your FRITZ!Box 7272 on a cable connection. Use a network cable. 1. Connect the free end of the network cable to the LAN (Ethernet) port on the cable modem. 2. Connect the other end of the network cable to the socket on the FRITZ!Box labeled “LAN 1”. 3.
Connecting to the Landline Telephone Network Connecting to a Router or a Network You can use the FRITZ!Box at an already existing Internet access. To do this the FRITZ!Box is connected to the router or network. Connecting Using a Network Cable A network cable is required to connect the FRITZ!Box to a router. 1. Insert one end of the cable into the socket on the FRITZ!Box labeled “LAN 1”. 2. Insert the other end of the cable into a network socket on the router or in the network.
Connecting to the Landline Telephone Network Connecting to the Analog Line r we Po SL /D er n Int et ed Fix e Lin DE CT o I nf DEC T WPS FON 2 N N1 L FO LAN 2 WLA LAN 1 LAN 3 LAN 4 Power FON S0 DSL/TE Analog telephone line 1. Insert the long, gray end of the DSL/telephone cable in the socket on the FRITZ!Box labeled “DSL/TEL”. 2. Insert the short, black end of the cable into the landline socket for your line.
Connecting to the Landline Telephone Network Connecting to the ISDN Line r we Po /D SL et er n Int ed Fix Lin e CT DE o Inf DEC T WLA N WPS LAN 3 LAN 2 LAN 1 N1 L FO FON 2 LAN 4 Power FON S0 DSL/TE ISDN line 1. Insert the long, gray end of the DSL/telephone cable into the socket on the FRITZ!Box labeled “DSL/TEL”. 2. Insert the short, black end of the cable into a socket (S0 interface) on your ISDN NTBA.
Connecting a Computer with a Network Cable 5 Connecting a Computer with a Network Cable You can connect computers and other network devices with the FRITZ!Box using a network cable. 5.1 Connecting to the Computer One computer or other network device can be connected to each LAN port of the FRITZ!Box. wer Po /D SL er n Int et e Fix dL ine CT DE o I nf DEC T WLAN WPS LAN 4 DSL/TEL FON 1 Power FON S0 FON 2 Connecting a computer using a network cable 1.
Connecting a Network Hub or Switch 5.2 Connecting a Network Hub or Switch You can connect a network hub or network switch to the FRITZ!Box. r we Po SL /D et ern Int e Lin ed Fix CT DE o Inf DEC T WPS 1. FON 1 N DSL/TEL LAN 2 WLA LAN 1 LAN 3 LAN 4 Power FON S0 FON 2 Insert the network cable included in the package into the uplink port of the network hub or network switch. You can also use any other network cable. For more information, see page 179. 2.
Connecting Computers with the FRITZ!Box over Wireless LAN 6 Connecting Computers with the FRITZ!Box over Wireless LAN Computers and other devices with wireless LAN, for instance smartphones and network printers, can be connected wirelessly with the FRITZ!Box. 6.
Establishing a Wireless LAN Connection Using WPS 2. Open the wireless LAN software on the computer. In Windows 8 and 7, for instance, click the wireless LAN icon in the task bar. 3. Select the wireless radio network of the FRITZ!Box. The preconfigured name of the wireless LAN radio network is “FRITZ!Box 7272”. 4. Click “Connect”.
Establishing a Wireless LAN Connection Using WPS Connecting to Other Wireless Devices Here is how to establish a wireless connection with WPS on a wireless LAN device without Windows: 1. If the “WLAN” LED on the FRITZ!Box is off, press the “WLAN” button briefly. The wireless radio network of the FRITZ!Box will be switched on. 2. Use your wireless device to search for wireless networks at your location. See the documentation of the wireless LAN device for instructions on how to do this. 3.
Establishing a Wireless LAN Connection with a Network Key 6.3 Establishing a Wireless LAN Connection with a Network Key You can establish a wireless LAN connection by entering the FRITZ!Box network key on the wireless device: 1. If the “WLAN” LED on the FRITZ!Box is off, press the “WLAN” button briefly. The wireless radio network of the FRITZ!Box will be switched on. 2. Open the wireless LAN software on your wireless device. In Windows 8.
The FRITZ!Box User Interface 7 The FRITZ!Box User Interface The FRITZ!Box has a user interface you can open in a web browser on your computer. In the user interface you can set up the FRITZ!Box, enable or disable functions and receive information on the FRITZ!Box and on your connections. 7.1 Opening the User Interface The FRITZ!Box user interface can be opened on any computer connected with the FRITZ!Box. 1. Start a web browser on your computer. 2. Enter fritz.box in the address line of the browser.
Overview: FRITZ!Box at a Glance The “Overview” page of the FRITZ!Box In the upper area of the window the complete product name of your FRITZ!Box is displayed, along with the currently installed version of FRITZ!OS, and its current energy consumption. Depending on your settings, the following information is displayed here: • • the name you assigned for your FRITZ!Box; see page 155 the availability of a new FRITZ!OS version for your FRITZ!Box; see page 46.
Standard View and Advanced View 7.3 Standard View and Advanced View Combinations of various settings in the “Internet” and “Home Network” areas can produce a situation in which the user interface of the FRITZ!Box can no longer be opened. Enabling the advanced view in these areas is recommended only if you have advanced network expertise. The FRITZ!Box user interface has two views: the standard view and the advanced view. Upon delivery, the FRITZ!Box interface is set to display the standard view.
Using System Functions of the FRITZ!Box 8 Using System Functions of the FRITZ!Box The FRITZ!Box offers a slew of system functions like notification services, diagnostics functions and updating services, which inform you about the activities and functional status of the FRITZ!Box and help you operate the FRITZ!Box safely and always keep it up to date. 8.
Using Energy-Saving Functions of the FRITZ!Box What is more, the FRITZ!Box saves energy by reducing processing power on standby and lowering the power consumption of idle functions. The FRITZ!Box also offers various settings for energy-saving operation. The current energy consumption of the total FRITZ!Box system is displayed on the “Overview” page. From there, click with the mouse to view the “Energy Monitor”, which displays details on the energy consumption.
Using Energy-Saving Functions of the FRITZ!Box Enabling Energy-Saving Mode for USB Hard Drives In the FRITZ!Box you can enable an energy-saving function for USB hard drives connected to the FRITZ!Box. When the energy-saving function is enabled, connected USB hard drives will be switched off when they are idle—as long as the hard drives support the energy-saving function. Enable the energy-saving function in the “Home Network / USB Devices” menu in the FRITZ!Box user interface.
Push Services: Notification Services of the FRITZ!Box 8.3 Push Services: Notification Services of the FRITZ!Box Push services are notification services that inform you about the activities of your FRITZ!Box and assist you in saving your passwords and FRITZ!Box settings. With the push services you can have e-mail sent to you at regular intervals informing you about the latest connections, usage and configuration of your FRITZ!Box.
Push Services: Notification Services of the FRITZ!Box Push Service Information Save settings The settings of your FRITZ!Box are saved automatically and sent to the specified e-mail address before every update and each time the factory settings are restored. Forgot password Sends you an access link to the specified e-mail address if you have forgotten your password. Current IP address Sends the IP address assigned by the Internet service provider every time the Internet connection is established.
Locking the Buttons on the FRITZ!Box 8.4 Locking the Buttons on the FRITZ!Box With the “Keylock” function in the “System / Buttons and LEDs” menu you can lock the buttons on your FRITZ!Box. Locking the keys prevents the settings for your FRITZ!Box or your home network from being changed unintentionally or without authorization. Example With the “WLAN” button the wireless network of the FRITZ!Box can be switched off at the touch of a button.
Saving and Restoring the FRITZ!Box Settings Saving Settings Backup files that are not protected by assigning a password constitute a security gap. Protect your backup file with a password to avoid security problems. A wizard is available in the FRITZ!Box user interface to assist you in saving your FRITZ!Box settings, guiding you through the process step by step. 1. Open the FRITZ!Box user interface; see page 33. 2. On the “Overview” page, select the “Wizards” menu. 3.
Update: Updating FRITZ!OS • Backup files created with a different FRITZ!Box model. If you apply settings from a backup file that was created with a FRITZ!Box of a different model, then you can restore several selected settings to your FRITZ!Box. A wizard is available in the FRITZ!Box user interface to assist you in restoring your FRITZ!Box settings, guiding you through the process step by step. 1. Open the FRITZ!Box user interface; see page 33. 2. On the “Overview” page, select the “Wizards” menu. 3.
Update: Updating FRITZ!OS Performing an Update with the Wizard A wizard is available in the FRITZ!Box user interface to assist you in updating your FRITZ!Box. The wizard checks whether an update of the FRITZ!OS is available for your FRITZ!Box and guides you step by step through installation. Performing the Update 1. Open the FRITZ!Box user interface; see page 33. 2. On the “Overview” page, select the “Wizards” menu. 3. Start the “Update” wizard.
Update: Updating FRITZ!OS Performing a Manual Update In some cases it is not possible to perform an automatic update, for instance when the FRITZ!Box is not connected to the Internet. Then you have the option of performing an update manually. Downloading the FRITZ!OS File Before you can perform a manual update, you must download an up-to-date FRITZ!OS file from the Internet (using your neighbor’s or friend’s computer, or at an Internet café) and save it on your computer or on a connected storage medium. 1.
Update: Updating FRITZ!OS 4. Click the “Save Settings” button to save the current settings of your FRITZ!Box on your computer and save the export file on your computer. Using this file you can restore the settings of your FRITZ!Box as needed. 5. Click the “Browse...” button and choose the file with the new FRITZ!OS you already downloaded and saved on your computer. Interrupting the FRITZ!OS update could damage your FRITZ!Box.
Configuring an Internet Connection in the FRITZ!Box 9 Configuring an Internet Connection in the FRITZ!Box Once you have connected the FRITZ!Box to your Internet connection, you must configure the Internet connection in the FRITZ!Box user interface so that the FRITZ!Box can establish the connection to your Internet service provider and connect to the Internet.
Internet Connection for Cable Configuring Your Internet Connection Without the Wizard Choose this method if the FRITZ!Box is connected to a DSL modem or a DSL router, or integrated into an existing network. 1. Open the FRITZ!Box user interface; see page 33. 2. Switch to the advanced view; see page 35. 3. Select the “Internet / Account Information” menu and enter your account information. 4. Click “Apply” to save your entries. In the Help of the FRITZ!Box user interface detailed instructions. 9.
Internet Connection over LAN 1: FRITZ!Box as a Router 3. Select the “Internet / Mobile Communications” menu. The “Mobile Communications” menu is not available until the UMTS/HSPA modem has been connected to the USB port of the FRITZ!Box. 4. Select the setting “Mobile connection enabled”. 5. Configure the settings for your Internet connection over the mobile communications network. In the Help of the FRITZ!Box user interface you can find detailed instructions.
Internet Connection over LAN 1: FRITZ!Box as a Router 2. Open the FRITZ!Box user interface; see page 33. 3. Select the “Internet / Account Information” menu. 4. Select the “Existing connection over LAN” entry from the “Internet service provider” drop-down list. 5. Click “Apply”. The FRITZ!Box is configured as a router and the network range is changed automatically. The FRITZ!Box, along with the connected network devices, forms its own self-contained network.
Surfing the Net 9.5 Surfing the Net Once you have set up the Internet connection in your FRITZ!Box, you can surf the Internet with any computer connected to the FRITZ!Box. 1. Start a web browser on your computer. 2. Enter in the address field the URL of the web page you would like to visit, for instance en.avm.de. The requested Internet page is opened and displayed.
Connecting Telephones and Other Terminal Devices 10 Connecting Telephones and Other Terminal Devices This chapter describes how to connect telephones, fax machines, answering machines and telephone systems (PBXs) to the FRITZ!Box. 10.1 Connecting an Analog Telephone or Terminal Device r we Po /D SL ern Int et e Lin ed Fix DE CT o I nf DEC T N WPS LAN 2 WLA LAN 1 LAN 3 LAN 4 Power FON S0 FON 2 FON 1 DSL/TEL 1. Connect the terminal device to the “FON 1” or “FON 2” port.
Registering FRITZ!Fon and Other Cordless (DECT) Telephones r we Po /D SL et ern Int e Lin ed Fix CT DE o Inf DEC T WPS FON 2 N N1 L FO LAN 2 WLA LAN 1 LAN 4 LAN 3 Power FON S0 DSL/TE 2. Configure the ISDN telephone in the FRITZ!Box; see page 58. Connecting Multiple ISDN Telephones With S0 bus cabling you can connect up to eight ISDN telephones to the FRITZ!Box. Please note for configuration: 10.
Registering an iPhone or Android Smartphone 10 seconds 3. Info Internet WLAN WPS Fixed LIne WLAN Power / DSL Powe DECT If you are asked for the PIN of the base station, enter the PIN pin of the FRITZ!Box. The preset value is 0000. The PIN is listed in the FRITZ!Box user interface under “DECT / Base Station”. The cordless telephone is registered with the FRITZ!Box. 4. 10.4 Configure the cordless telephone in the FRITZ!Box; see page 58.
Registering an iPhone or Android Smartphone • You can accept calls to your Internet telephone numbers and landline telephone numbers on your smartphone. • The smartphone can still be reached at the mobile telephone number. Registering a Smartphone with FRITZ!Box 1. Establish a wireless LAN connection to the FRITZ!Box on your smartphone; see page 29. 2. Install FRITZ!App Fon on your smartphone. FRITZ!App Fon is available at the Google Play Store and in the Apple App Store. 3.
Connecting an IP Telephone 10.5 Connecting an IP Telephone IP telephones are telephones for making calls over the Internet and other computer networks. If your FRITZ!Box 7272 is connected with a landline, you can use the connected IP telephone to make calls over the landline network as well. Connecting via LAN or Wireless LAN 10.6 1. Connect the IP telephone to the FRITZ!Box using a LAN cable or wireless LAN. 2. Configure the IP telephone in the FRITZ!Box; see page 58.
Configuring the FRITZ!Box for Telephone Calls 11 Configuring the FRITZ!Box for Telephone Calls This chapter describes how to configure your FRITZ!Box for making telephone calls. 11.1 Configuring Your Telephone Numbers Configure the following telephone numbers in the FRITZ!Box using the wizard: • All Internet telephone numbers that are not configured in the FRITZ!Box automatically by the provider. • Landline telephone numbers you would like to assign to telephones and other terminal devices.
Configuring Telephones and Other Terminal Devices in the FRITZ!Box 11.2 Configuring Telephones and Other Terminal Devices in the FRITZ!Box Configure your telephones and other terminal devices in the FRITZ!Box. To do this, for each terminal device define: • Internal name, which will be displayed in the call list of the FRITZ!Box. • Telephone number the terminal device uses for outgoing calls to the public telephone network.
Password Protection: Using FRITZ!Box Safely 12 Password Protection: Using FRITZ!Box Safely Password protection for access to the user interface is a security feature of your FRITZ!Box. This section describes how to use a password for the FRITZ!Box user interface and why you should use password protection. Additional security information on using the FRITZ!Box, see the AVM web site at en/avm.de/guide/security. 12.
Using a FRITZ!Box Password Password Tips • Select a password with at least eight characters, which includes capitals and lower-case letters as well as numerals and special characters. See “Characters for Passwords” in the Help of the FRITZ!Box user interface for more information about which characters you’re allowed to use. • Be sure to keep your passwords in a safe place! – Use the “Forgot password” push service, see Push Services: Notification Services of the FRITZ!Box from page 39.
Using a FRITZ!Box Password 4. Save your changes by clicking “Apply”. You will be directed to the welcome screen of your FRITZ!Box. 5. Enter your user name to log in to the user interface of your FRITZ!Box. Password protection is enabled in your FRITZ!Box. With the FRITZ!Box password it is not possible to access the FRITZ!Box from the Internet. For users who require access to the FRITZ!Box via Internet, you must also set up an account as a FRITZ!Box user; see page 62.
Using FRITZ!Box Users 12.3 Using FRITZ!Box Users If you would like to access your FRITZ!Box from the Internet, you have to configure password-protected login with FRITZ!Box user accounts. Also use this login method if multiple users with different rights are to have access to the FRITZ!Box. A FRITZ!Box user reaches the user interface of the FRITZ!Box by entering her or his personal password. There she or he can view and change those contents or settings for which she or he has been granted access rights.
Using FRITZ!Box Users 5. In the “Rights” area, specify for each FRITZ!Box user which FRITZ!Box contents she or he is allowed to use. Make sure that those users who are allowed to configure settings on the FRITZ!Box are assigned at least the right “FRITZ!Box settings”. For more information on rights, see the section from page 64. 6. Save your entries by clicking “OK”. The FRITZ!Box user account has been set up.
Using FRITZ!Box Users 3. Enter a name, a valid e-mail address and a password for the new user. For more information on the characters you may use for the password, see the Help in the FRITZ!Box user interface. 4. Specify whether or not the new FRITZ!Box user is allowed to access from the Internet the FRITZ!Box contents for which she or he has access rights. Keep in mind that a corresponding service must also be enabled in the FRITZ!Box for Internet access.
Using FRITZ!Box Users • FRITZ!Box settings A user with these rights can open the fritz.box or myfritz.box view of the FRITZ!Box user interface. Here she or he can see and edit all settings. Configuration rights automatically include the right to access voice messages, faxes, FRITZ!App Fon and the call list as well as the right to control smart home devices. A registered user cannot revoke these rights herself or himself and cannot disable her or his own account.
Using FRITZ!Box Users Accessing the FRITZ!Box from the Internet To be able to access your FRITZ!Box from the Internet, the following conditions must be fulfilled: • You have set up an account with the MyFRITZ! service; see page 73. Your FRITZ!Box is registered with this MyFRITZ! account. • The option “Access from the Internet permitted” is enabled in your user account.
Using FRITZ!Box Users • With a FRITZ!Box user account that has only the right to access a certain area of the NAS you can grant your friends Internet access to your latest vacation pictures, for instance. • As a FRITZ!Box user with the “Smart home” right, you can switch your lamps or aquarium pumps on and off from anywhere in the world. The prerequisite is that you connect them to smart home devices from AVM (like FRITZ!DECT 200, for instance) which are integrated in the home network of your FRITZ!Box.
Using FRITZ!Box Users Quick Access to Your Own User Account In the upper navigation bar of the FRITZ!Box is the name of the FRITZ!Box user account with which the user is currently logged in to the user interface. Click the blue triangle to control basic functions of this user account: • Changing the e-mail address Select the “Change e-mail address” entry to assign a different e-mail address to the current user account.
Forgot Password—What to Do 1. In the FRITZ!Box user interface, open the “System / FRITZ!Box Users / User” menu. 2. Click the “Edit” button for the user account to be disabled. 3. In the “User” area, remove the checkmark in front of the “User account enabled” option. 4. Apply the change by clicking “OK”. The user account has been disabled. 12.
Mode “No login” Here is how to restore the factory settings to the FRITZ!Box: 1. Disconnect the FRITZ!Box from the power supply. 2. Reconnect to the power supply after about five seconds and wait until the “Power / DSL” LED lights up. In the first ten minutes after restarting you can restore the factory settings to the FRITZ!Box. 3. Open the browser on a computer connected with the FRITZ!Box by LAN or wireless LAN and enter fritz.box in the address field. 4.
Mode “No login” For comprehensive information about logging in to the FRITZ!Box with a password, see the sections Using FRITZ!Box Users from page 62 and Using a FRITZ!Box Password from page 60.
MyFRITZ!: Accessing the FRITZ!Box from Anywhere 13 MyFRITZ!: Accessing the FRITZ!Box from Anywhere MyFRITZ! is a web service by AVM, with which you can access your FRITZ!Box from anywhere in the world over the Internet, just as if you were at home. This chapter describes what MyFRITZ! does and how to configure MyFRITZ!. Why MyFRITZ!? Using an active Internet connection on any computer, tablet or smartphone, with MyFRITZ! accessing your FRITZ!Box from anywhere is safe and simple.
Configuring MyFRITZ! 13.1 Configuring MyFRITZ! The MyFRITZ! service can be used only with a MyFRITZ! account. Register your MyFRITZ! with this FRITZ!Box account. Once your FRITZ!Box is registered with your MyFRITZ! account, the FRITZ!Box determines the public IP address each time it is changed and conveys it to the MyFRITZ!. The FRITZ!Box can be reached at this IP address in the Internet from anywhere in the world. When you log in to MyFRITZ! you will be forwarded to the FRITZ!Box using the IP address.
Using MyFRITZ! 6. If you do not have a FRITZ!Box user account yet, you will be prompted to set one up by assigning a user name and an additional password. If you already have a FRITZ!Box user account, follow the instructions in the FRITZ!Box user interface. For security reasons access to the FRITZ!Box from the Internet is possible only for users with a FRITZ!Box user account. 7. You receive an e-mail from MyFRITZ! containing a registration link.
Using MyFRITZ! MyFRITZ! in the Web Browser 1. Open the myfritz.net web site. 2. Log in with your e-mail address and your MyFRITZ! password. 3. Click the “To My FRITZ!Box” button. 4. To register with your FRITZ!Box, enter the data of your FRITZ!Box user account. You will be directed to the MyFRITZ! page of your FRITZ!Box. Here you have access to the FRITZ!Box contents that are released for sharing in your FRITZ!Box user account; see page 64.
Using MyFRITZ! 4. To register with your FRITZ!Box, enter the data of your FRITZ!Box user account. These are your e-mail address or your FRITZ!Box user name plus the corresponding password. You will be directed to the MyFRITZ! page of your FRITZ!Box. Here you have access to the FRITZ!Box contents that are released for sharing in your FRITZ!Box user account; see page 64.
Security with MyFRITZ! 13.3 Security with MyFRITZ! For the following MyFRITZ! activities the HTTPS security protocol is used: • • • setting up a MyFRITZ! account with myfritz.net • accessing the user interface of the FRITZ!Box over myfritz.net and over the MyFRITZ!App. registration of the FRITZ!Box with the MyFRITZ! account accessing the MyFRITZ! page of your FRITZ!Box over myfritz.net The FRITZ!Box generates its own HTTPS certificate.
FRITZ!Box as an Internet Router 14 FRITZ!Box as an Internet Router The FRITZ!Box connects computers in your home network with the Internet. This chapter explains the possibilities presented by using the FRITZ!Box as an Internet router and how to take advantage of them. 14.1 Parental Control: Access Profiles for Internet Use Using access profiles you can control the use of the Internet by devices in your network.
Parental Control: Access Profiles for Internet Use • Network devices that log in to the FRITZ!Box guest network are automatically assigned the “Guest” access profile. This is the only access profile possible in the guest network. Preconfigured Access Profiles In the FRITZ!Box there are four preconfigured access profiles available for use. The “Standard” Access Profile FRITZ!Box 7272 Property Description Limitations In the factory settings the “Standard” profile is allowed to do everything.
Parental Control: Access Profiles for Internet Use The “Guest” Access Profile Property Description Limitations The profile has the following settings configured upon delivery: • There are not time restrictions. • HTTPS queries are permitted. • Surfing and mail are allowed. Web access is blocked for all other network applications. Changeable The “Guest” profile can be changed.
Parental Control: Access Profiles for Internet Use Online Time The online time is defined as follows: Setting Description Period On a timetable you define when the Internet connection may be used. Online time For each day of the week you define how long the Internet is allowed to be used. Shared budget You decide and define whether all network devices that use the same access profile must share this online time limit.
Parental Control: Access Profiles for Internet Use • Permit web sites with a whitelist: – The whitelist is a filter list that should be used when access should be limited to just a few web sites. – Access to web pages entered in the whitelist is permitted. – When a whitelist is used, only those web sites included in the list can be opened, and no others.
Parental Control: Access Profiles for Internet Use Limitations The “Internet / Filters” menu is not available if you have configured the FRITZ!Box as IP client. In this case, use the corresponding functions of the router whose Internet connection is being shared. Requirements • Configure the access profiles required for the members of the home network; see Configuring an Access Profile on page 83. • Prepare the filter lists if you would like to use filter lists, see Editing Filter Lists from page 84.
Parental Control: Access Profiles for Internet Use Configuring an Access Profile 1. Open the FRITZ!Box user interface; see page 33. 2. Select the “Internet / Filters” menu. 3. Select the “Access Profiles” tab. 4. Click 5. Configure the settings for the access profile in the “New Access Profile” window. Use the FRITZ!Box Help. .
Parental Control: Access Profiles for Internet Use Adding Network Applications Requirements The “Internet / Filters” menu is available only if you have set up the Internet connection in the FRITZ!Box and already established an Internet connection. Limitations The “Internet / Filters” menu is not available if you have configured the FRITZ!Box as IP client. In this case, use the corresponding functions of the router whose Internet connection is being shared. Adding a Network Application 1.
Parental Control: Access Profiles for Internet Use • AVM FRITZ!Box parental control is installed on the computer as a service. The service must be enabled at all times. If it is not enabled, the FRITZ!Box will not detect the user accounts. Windows users that are not detected are treated like user accounts without any parental controls. Downloading AVM FRITZ!Box Parental Controls from the AVM Web Sites 1. Open the AVM web site: ftp://ftp.avm.de. This will take you to AVM’s FTP server. 2. Select “fritz.
Port Forwarding: Making Computers Accessible from the Internet 14.2 Port Forwarding: Making Computers Accessible from the Internet With default settings in the FRITZ!Box, programs on your computer and LAN cannot be accessed from the Internet. For applications like online games and file sharing software or server services like HTTP, FTP, VPN, terminal and remote access servers, you have to make your computer accessible for other Internet users.
Port Forwarding: Making Computers Accessible from the Internet ESP IPv4: GRE Within IPv4 networks you can open the firewall for the two protocols ESP and GRE, which do not use ports. Exposed host IPv4: (Open firewall completely) Within IPv4 networks you can open the firewall completely for one computer. This computer is then no longer protected by the FRITZ!Box firewall.
Dynamic DNS: Name instead of IP Address 3. The FRITZ!Box’s public IPv4 address is displayed on the “Overview” page in the “Connections” area. Can Always Be Reached, Even When the IP Address Changes Every time the Internet connection is interrupted, the Internet service provider re-assigns the IP address. The IP address may change in the process. Therefore it is a good idea to use MyFRITZ! or dynamic DNS so that the IP address can always be reached under the same name.
Access from the Internet via HTTPS, FTP and FTPS 14.4 Access from the Internet via HTTPS, FTP and FTPS Over the Internet it is possible to access the user interface of the FRITZ!Box. With a laptop, smartphone or tablet PC you can configure settings in the FRITZ!Box user interface.
Prioritization: Right of Way for Internet Access • FTPS (FTP over SSL) FTPS is a method for encrypting the FTP protocol. Enable this protocol to secure transmission over FTP. Enabling HTTPS, FTP and FTPS in the FRITZ!Box 14.5 1. Open the FRITZ!Box user interface; see page 33. 2. Enable the advanced view. 3. Select the “Internet / Permit Access” menu. 4. Select the “FRITZ!Box Services” page and enable the protocols you need. See also the Help the user interface.
Prioritization: Right of Way for Internet Access • When the Internet connection is working at full capacity, the network packets of the applications of this category will always be sent first. In this case data from network applications assigned to other categories will be transmitted later. • If multiple network applications are assigned to this category, then they must share the available capacity.
Prioritization: Right of Way for Internet Access • If no other network applications are active, then the background applications receive the entire bandwidth. Prioritization Method in the FRITZ!Box The following techniques are used in the FRITZ!Box to send data packets according to their prioritization: • Change in the order in which packets are sent to the Internet (upstream direction) The order of the packets the FRITZ!Box receives from the Internet (downstream direction) cannot be changed.
VPN: Remote Access to the Home Network 14.6 VPN: Remote Access to the Home Network Via a VPN (Virtual Private Network) a secure remote access to the network of the FRITZ!Box can be established. VPN in the FRITZ!Box IPSec VPN in the FRITZ!Box is based on the IPSec standard. Computer—LAN Computer—LAN linkup: VPN connections can be configured for individual remote computers. LAN—LAN LAN—LAN linkup: VPN connections can be configured for remote networks.
VPN: Remote Access to the Home Network 4. Select the “VPN” page. See also the Help available in the FRITZ!Box user interface for assistance in configuring VPN. Supplementary Software for VPN All of the information required for a VPN is saved in a configuration file. The terminals involved in any VPN must receive this file. Individual computers that are networked over a VPN require a VPN client.
Freely Selectable DNS Servers 14.7 Freely Selectable DNS Servers DNS servers are preset in the FRITZ!Box for IPv4 and IPv6. These are the DNS servers assigned by the Internet service provider. For both IPv4 and IPv6, the preset DNS server can be replaced by a free DNS server. Free DNS servers include, for instance, OpenDNS and Google DNS. Here is how to change the DNS server entry: The “DNSv6” page is displayed only if you enabled IPv6 support for the FRITZ!Box on the “IPv6” page. 14.8 1.
IPv6: The New Internet Protocol The home user relies on the authenticity of the IP address returned by the DNS server. Authentic means that the response is the IP address of the desired web site, and not a faked IP address that leads to a fake web site. DNSSEC can ensure that the returned addresses are authentic. Support with the FRITZ!Box The FRITZ!Box supports DNSSEC queries over UDP. The FRITZ!Box has a DNS proxy. The computers in the home network use the FRITZ!Box as a DNS server.
IPv6: The New Internet Protocol • The DNS resolver of the FRITZ!Box supports queries for IPv6 addresses (AAAA records) and can query the upstream DNS resolver of the Internet service provider over IPv6. • The globally valid prefix is distributed via router advertisement. • For guest access to the wireless LAN, the home network and wireless guests are separated by IPv6 subnetworks.
Mobile Network: Replacing Faulty DSL • IPv6 is already installed and enabled in the Windows 7 and Windows Vista operating systems. • IPv6 is not installed and enabled in standard Windows XP. You must install and enable IPv6 in order to use it. The IPv6 installation requires Service Pack 2 for Windows XP. • IPv6 has been available in the Mac OS X operating systems since Mac OS 10. 14.
LISP: FRITZ!Box as a LISP Router As soon as the DSL connection is stable and available for at least 30 minutes, the connection will be switched back to DSL. 14.11 LISP: FRITZ!Box as a LISP Router LISP is a routing architecture which separates information about location and identity. There are two IP addresses: one for the location and one for the identity. The FRITZ!Box can be configured as a LISP router. • • • This chapter address system administrators.
LISP: FRITZ!Box as a LISP Router Properties of RLOC and EID RLOC EID • specifies the location where the addressed network (network segment or network device) is located • is assigned by the Internet service provider • is a public IP address • is contained in the external header of the LISP packet • can be an IPv4 address • can be an IPv6 address • identifies a network (network segment or network device) • is assigned by the LISP provider • is contained in the internal header of the LISP
LISP: FRITZ!Box as a LISP Router PETR (Proxy ETR) A PETR (Proxy ETR) is required for communication between LISP sites and non-LISP sites. On the LISP site it works like a LISP router; on the nonLISP site it works like a native IP router. PITR (PROXY ITR) A PITR (Proxy ETR) is required for communication between LISP sites and non-LISP sites. On the LISP site it works like a LISP router; on the nonLISP site it works like a native IP router. xTR xTR is what we call a component that is both ETR and ITR.
LISP: FRITZ!Box as a LISP Router Configuring a LISP Router FRITZ!Box 7272 1. Open the FRITZ!Box user interface; see page 33. 2. Enable the advanced view. 3. Select the “Internet / Account Information” menu. 4. Select the “LISP” tab. 5. Enable the setting “LISP support enabled”. 6. Enter in the fields the information you received from the LISP provider.
FRITZ!Box as a WLAN Access Point 15 FRITZ!Box as a WLAN Access Point The FRITZ!Box is a wireless access point for wireless devices like notebooks, tablets or smartphones. The FRITZ!Box can establish wireless LAN connections compliant with the fast Wireless N standard. The FRITZ!Box is preconfigured with an encryption method from today’s safest method WPA2. This encryption method is supported by most of the latest wireless devices.
Extending a Wireless Radio Network Switching Wireless LAN On and Off You can switch the wireless radio network of the FRITZ!Box on and off at any time, even when the device is hibernating. • Press the “WLAN” button on the FRITZ!Box briefly or • Switch on the wireless LAN radio network using a connected telephone wireless LAN on r96s1s wireless LAN off r96s0s 15.2 Extending a Wireless Radio Network The range of a wireless radio network is not fixed.
Wireless LAN—Getting Technical Using an Existing FRITZ!Box as a Repeater You can extend the wireless LAN radio network of your FRITZ!Box with an additional FRITZ!Box you already have. To extend your wireless LAN, configure the repeater function in this device. You can configure a FRITZ!Box as a repeater by working through the following steps: 1. Open the FRITZ!Box user interface; see page 33. 2. Enable the advanced view. 3.
Wireless LAN—Getting Technical IEEE 802.11b With a maximum throughput rate of 11 Mbit/s, this is the oldest wireless standard. Older wireless devices of the first generation can communicate with the FRITZ!Box using 802.11b. However, if the wireless device supports newer standards such as 802.11g, the latest standard should be used. IEEE 802.11g In this wireless LAN standard data are transmitted in the 2.4GHz range at a maximum gross throughput of 54 Mbit/s.
Wireless LAN—Getting Technical Make a note of which standards the wireless devices in your network are compatible with and then adjust the FRITZ!Box settings according to the following information: 11n, 11g In your radio network there are wireless LAN devices that are compatible with one or both of the following standards: • • 802.11n 802.11g In this case set the wireless LAN standard for the 2.4-GHz frequency band to: 802.11n+g.
Wireless LAN—Getting Technical The Standard for Security IEEE 802.11i The WPA2 security mechanism is defined in the IEEE 802.11i standard. WPA2 is an extension of the familiar security mechanism WPA (Wi-Fi Protected Access). The main feature of the extension of WPA to WPA2 is the AESCCMP encryption process. Mechanism Encryption WPA TKIP (Temporary Key Integrity Protocol) WPA2 TKIP AES-CCMP based on the extremely secure AES (Advanced Encryption Standard) procedure.
Wireless LAN—Getting Technical In the 2.4-GHz frequency range the European regulation authorities have designated 13 channels for wireless LAN. A channel can have a bandwidth of 20 MHz (throughput of up to 216 Mbit/s) or 40 MHz (throughput of up to 450 Mbit/s). Channels located directly next to each other in the 2.4-GHz band may overlap and result in mutual interference. For instance, if several wireless networks are operated close to each other in the 2.
FRITZ!Box as a Telephone System 16 FRITZ!Box as a Telephone System This chapter describes how to use the FRITZ!Box as a telephone system. 16.1 Telephone Book How Can I Use the Telephone Book? • Quick-dial: With quick-dial numbers you assign in the telephone book entries you can make calls on all telephones. • FRITZ!Fon: The telephone book is available in the menu of your FRITZ!Fon cordless telephones. You can set up a separate telephone book for each FRITZ!Fon.
Telephone Book 5. Under “Telephone Assignment”, select all FRITZ!Fon cordless telephones on which you would like to use the telephone book. 6. Save with “OK”. The telephone book is available in the menu of the FRITZ!Fon cordless telephones. Configuring Online Telephone Books (e.g. Google Contacts) 1. Open the FRITZ!Box user interface; see page 33. 2. Select “Telephony / Telephone Book”. 3. Click the “New Telephone Book” link. 4. Select “Use the telephone book of an e-mail account”. 5.
Call List Configuring Click to Dial 1. Open the FRITZ!Box user interface; see page 33. 2. Select “Telephony / Telephone Book / Click to Dial”. 3. Enable click to dial and select a telephone. 4. Save with “OK”. You can use click to dial. In the Help of the FRITZ!Box user interface tailed instructions. 16.2 you can find de- Call List The call list of the FRITZ!Box contains your telephone calls and calls you missed (missed calls).
Answering Machine 16.3 Answering Machine You can use the FRITZ!Box as an answering machine without connecting any additional devices. Features • If desired you can receive any new messages automatically by e-mail. • If you have more than one telephone number, you can configure up to five different answering machines. • Schedule: Specify when the answering machine is on and off on the individual days of the week. • Remote playback: Check the answering machine from on the go.
Answering Machine Operating an Answering Machine on the Telephone The answering machine can be operated using a voice menu on the telephone. 1. Press the following keys on the telephone: Answering Machine Keys Answering machine 1 ss600 Answering machine 2 ss601 Answering machine 3 ss602 Answering machine 4 ss603 Answering machine 5 ss604 2. Pick up the handset. 3. Follow the voice menu. Or you can press a key right away; see the section Voice Menu on page 116.
Answering Machine Voice Menu Main menu 1 Play back messages If no messages are available, you will hear two short audio signals and return to the main menu.
Fax Function 16.4 Fax Function With the FRITZ!Box you can receive faxes without a fax machine. The FRITZ!Box can be configured to forward received faxes by e-mail. Configuring the Fax Function 1. Open the FRITZ!Box user interface; see page 33. 2. Select “Telephony / Telephony Devices”. 3. Click “Configure New Device”. 4. Under “Integrated in the FRITZ!Box”, select the “Fax function” option and confirm by clicking “Next”. 5.
Call Diversion 1. Open the FRITZ!Box user interface; see page 33. 2. Set up the fax function; see page 117. 3. Select “Telephony / Telephony Devices”. 4. Click the “Edit” button to open the settings of the fax function: 5. Click the “Help” button. The Help on the fax function contains instructions on how to set up automatic fax detection. 16.5 Call Diversion You can configure call diversion for incoming calls in the FRITZ!Box.
Dialing Rules for Outgoing Calls 4. Define which calls should be diverted. In the Help of the FRITZ!Box user interface find detailed instructions. 16.6 you can 5. Define the destination and the type of call diversion. 6. Click “OK” to save the settings. Dialing Rules for Outgoing Calls If you have multiple telephone numbers, you can configure dialing rules.
Blocking Telephone Numbers and Callers 16.7 Blocking Telephone Numbers and Callers In the FRITZ!Box you can block telephone numbers for outgoing and for incoming calls. How Does a Call Block Work? You can configure various kinds of call blocks: Call Block for Function Outgoing calls The blocked telephone number can no longer be called from the FRITZ!Box. Ranges of telephone numbers, for instance, mobile networks, can also be blocked.
Do Not Disturb 16.8 Do Not Disturb Do Not Disturb keeps a telephone from ringing at specified times. Calls you miss then appear in the FRITZ!Box call list. Configuring Do Not Disturb 16.9 1. Open the FRITZ!Box user interface; see page 33. 2. Select “Telephony / Telephony Devices”. 3. Click the “Edit” button to open the settings of a telephone: 4. Switch to the “Do Not Disturb” tab and configure the Do Not Disturb settings. 5. Click “OK” to save the settings.
Baby Monitor 16.10 Baby Monitor The following telephones can be configured as a baby monitor: • • FRITZ!Fon cordless telephones Telephones connected to the “FON 1” or “FON 2” on the FRITZ!Box. When a telephone is configured as a baby monitor, it calls a previously specified telephone number automatically whenever the volume in the room reaches a defined level. Configuring a FRITZ!Fon Cordless Telephone as a Baby Monitor 1. Press the menu key on your FRITZ!Fon. 2. Select “Suppl.
Baby Monitor Configuring a Telephone at the FON Port as a Baby Monitor Here is how to configure a telephone at the “FON 1” or “FON 2” port: 1. Press the following keys on the telephone: This Is Where the Baby Monitor Should Call Keys Another telephone or mobile number s41sr Internal telephone number, see page 124 s41sr All other telephones connect- s41s9r ed to the FRITZ!Box (group call) 2. The baby monitor is enabled.
Making Telephone Calls with Convenience Functions 16.11 Making Telephone Calls with Convenience Functions This chapter describes convenience functions you can use when placing and making telephone calls, for instance internal calling, forwarding calls, alternating between calls and three-party conferences. Making Internal Calls You can conduct free, internal calls between telephones connected to the FRITZ!Box. 1. Enter an internal telephone number on the telephone.
Making Telephone Calls with Convenience Functions 3. Hang up to connect the two external parties with each other. Defining the Telephone Number for the Next Call Before making a telephone call you can specify whether the FRITZ!Box connects the call using the landline or a certain Internet telephone number. Dialing rules and telephone numbers configured for the telephone are overridden for this call. 1.
Making Telephone Calls with Convenience Functions Three-Party Conference Call Conducting a Three-Party Conference Call 1. Connect the first call: Call someone or pick up their call. 2. Press the Hold button R. Call 1 is on hold. 3. Connect the second call: Enter an internal or external telephone number. When the called party accepts the call the second call is connected. 4. Press the keys R3. The three-party conference is set up. Any party can hang up. The two other parties remain connected.
Making Telephone Calls with Convenience Functions Accepting or Rejecting Waiting Calls on FON 1 and FON 2 Requirements • The “Call waiting” feature must be enabled for the individual telephone in the FRITZ!Box. The telephone settings can be edited in the user interface of the FRITZ!Box under “Telephony / Telephony Devices”. Rejecting a Waiting Call Press the keys R0. Accepting a Waiting Call and Holding Call 1 1. Press the keys R2. 2.
Making Telephone Calls with Convenience Functions Holding, Consultation and Alternating You can put a call on hold in order to call another party and establish a second call (consultation). You can alternate between the two calls as often as you like. Holding and Consultation 1. While you are conducting the call, press the Hold button R on the telephone. Call 1 is on hold. 2. Enter an internal or external telephone number. When the called party accepts the call the second call is connected.
Making Telephone Calls with Convenience Functions Using Keypad Shortcuts Keyboard shortcuts are commands consisting of multiple characters and numerals. They can be used to control services and features in the telephone network. For information about which keypad sequences you can use, contact your carrier. 1. Press the keys sr< Seq>. stands for a keyboard sequence.
Making Telephone Calls with Convenience Functions One-Time Explicit Transfer on the ISDN Line If ECT is not activated for your ISDN line, you can transfer a call to a second external party over the FRITZ!Box. Attention: While the two parties are talking with each other, your ISDN line is busy, and the charges contracted for your line incurred for two separate calls. Transferring Calls to an External Party 1. Press the keys s32r on the telephone and enter the telephone number of the first party. 2.
Making Telephone Calls with Convenience Functions Enabling Call-Back 1. Press the 5 key. You have 20 seconds for this. Wait for the second-long positive acknowledgment tone. 2. Hang up the handset. Call-back is enabled. Deleting Call-Back 1. On the same telephone, press the keys Rr37r. 2. Pick up the handset and hang it up again. If you are awaiting multiple return calls, the oldest call-back will be deleted.
FRITZ!Box as a DECT Base Station 17 FRITZ!Box as a DECT Base Station The FRITZ!Box is equipped with a DECT base station, on which you can register and configure a total of up to six cordless telephones. 17.1 Paging Cordless Telephones If you have misplaced a cordless telephone, you can find it by using a paging call: 17.2 1. Briefly press the “DECT” button of the FRITZ!Box. All cordless telephones registered on the FRITZ!Box will ring. 2.
Enabling DECT Eco 17.4 Enabling DECT Eco DECT Eco allows DECT radio transmission to be switched off during standby operation. How Does DECT Eco Work? When all registered cordless telephones are in standby operation, the DECT radio transmission of the FRITZ!Box and the telephones is switched off. When a call arrives or you press a key on a cordless telephone, the FRITZ!Box switches DECT radio transmission back on. Standby operation of a cordless telephone: • • • You are not making any calls.
FRITZ!Box Connects Network Devices 18 FRITZ!Box Connects Network Devices All network devices connected with the FRITZ!Box comprise a network. Network devices include, for instance, computers, game consoles and smartphones. The devices can be connected with the FRITZ!Box by cable or wirelessly. This chapter describes the network settings in the FRITZ!Box and how you can change them. You will also learn how you can change the IP settings for the computer in the most common operating systems. 18.
Network Settings in the FRITZ!Box The columns have the following meanings: Icon A green LED before the device name indicates that a device is actively connected with the FRITZ!Box, but not using the Internet connection at this time. A green-blue globe indicates that the device is currently using the Internet connection. Name This column displays the name under which the user or the network device is known to the FRITZ!Box.
Network Settings in the FRITZ!Box Always Assigning the Same IP Address The editing mode for network devices includes the setting “Always assign this network device the same IP address”. When this setting is enabled for a network device, the DHCP server of the FRITZ!Box will assign the same IP address to this device each time the connection is established.
Network Settings in the FRITZ!Box IPv4 Settings in the FRITZ!Box The IPv4 settings of the FRITZ!Box are preset upon delivery with the following values: Factory Settings IPv4 address 192.168.178.1 Subnet mask 255.255.255.0 DHCP server Enabled The IP address and the corresponding subnet mask yield the following values: Network address of the subnet 192.168.178.0 Entire IPv4 address range for the computers 192.168.178.2— 192.168.178.
Network Settings in the FRITZ!Box IPv4 Address in the FRITZ!Box Upon delivery the FRITZ!Box is assigned the following IPv4 address: 192.168.178.1 If you would like to change the IPv4 address, please read through the following sections. When Does It Make Sense to Change the IPv4 Address? You should change the IPv4 address of the FRITZ!Box if the following apply to your network: • You have an existing local IPv4 network, one subnet with several computers.
Network Settings in the FRITZ!Box Only one DHCP server may be active within any network. Assigning the IP addresses via the DHCP server ensures that all of the computers connected with the FRITZ!Box are located in the same IP network. The computers can receive their IPv4 addresses from the DHCP server only if the setting “Obtain an IPv4 address automatically” is enabled in the their IP settings. For more information, see the chapter Obtaining an IP Address Automatically from page 141.
Network Settings in the FRITZ!Box Changing Network Settings 1. Open the FRITZ!Box user interface; see page 33. 2. Enable the advanced view. 3. Select the “Home Network / Network” menu. 4. Select the “Network Settings” page. 5. Click the “IPv4 Addresses” or “IPv6 Addresses” button, depending on the address range you would like to change.
Obtaining an IP Address Automatically Unique Local Addresses Communication within the local network takes place via the Unique Local Addresses (ULA). If no IPv6 Internet connection is established, the network devices do not have a ULA and communication between them is restricted. For this case you can set the FRITZ!Box such that the network devices receive the ULA from the FRITZ!Box. DHCPv6 Servers in the Home Network The FRITZ!Box is equipped with its own DHCPv6 server.
Obtaining an IP Address Automatically 2. Enter “ncpa.cpl” in the search field and press Enter. Entering “ncpa.cpl” in Windows 8 3. Click the network connection between the computer and the FRITZ!Box with the right mouse button and select “Properties”. 4. Under “This connection uses the following items”, select “Internet Protocol Version 4 (TCP/IPv4)”. 5. Click the “Properties” button. 6.
Obtaining an IP Address Automatically Obtaining an IP Address Automatically in Mac OS X 1. Select the “System Preferences...” in the Apple menu. 2. In the “System Preferences” window, click the “Network” icon. 3. In the “Network” window, select the “Built-in Ethernet” entry from the “Show:” list. 4. Switch to the “TCP/IP” tab and select the “Using DHCP” option from the “Configure IPv4:” drop-down list. 5. Click “OK”. The computer now receives an IP address from the FRITZ!Box.
Connecting USB Devices to the FRITZ!Box 19 Connecting USB Devices to the FRITZ!Box The FRITZ!Box has a USB port to which you can connect various USB devices. All network devices in the FRITZ!Box home network can use these USB devices jointly and simultaneously. This chapter describes how to share a printer in the network, which USB devices can be used in your FRITZ!Box home network, and how to use these devices safely. 19.
Using USB Devices Safely • You can connect one standard USB printer or one all-inone device with scanner and fax function. The complete range of functions available in all-in-one printers is guaranteed only with the USB remote connection of the FRITZ!Box; see Sharing a USB Printer on page 147. • You can connect a USB hub to the FRITZ!Box and use up to four USB devices at this hub. You can use USB hubs with or without a separate power supply.
Configuring Access Rights 19.4 Configuring Access Rights You can protect the data on your USB storage from unauthorized access by securing the user interface of your FRITZ!Box with a password. In the “System / FRITZ!Box Users” menu you can • configure a shared password that is requested every time anyone in your home network accesses the FRITZ!Box and the connected USB storage media. • configure various FRITZ!Box users.
Sharing a USB Printer • Participants in the home network can use FTP software like FireFTP to exchange files among the FRITZ!Box storage media and workplaces. Alternatively, you can enter ftp://fritz.box in the address line of your Internet browser to access the storage media of the FRITZ!Box. If you would like to use FTP software, see the documentation of the software as well as the instructions in the Help in the FRITZ!Box user interface.
Sharing a USB Printer For information about how to configure a USB printer as a network printer, see the section Setting Up a USB Printer as a Network Printer on page 148. Using a USB Printer with FRITZ!Box USB Remote Connection Configure the USB printer on the FRITZ!Box with the FRITZ!Box USB remote connection if • the USB printer is an all-in-one device (fax/printer/scanner) and the entire range of functions is to be used.
Sharing a USB Printer Setting Up a USB Printer in Windows 8.1 or 8 1. Press the keyboard shortcut “Windows key+X” and select “Control Panel” from the context menu. 2. Click “Hardware and Sound” and select “Devices and Printers”. 3. In the menu bar, click “Add Printer”. 4. In the “Add a printer” window, select “The printer that I want isn’t listed”. 5. Enable the option “Add a printer using TCP/IP address or hostname” and click “Next”. 6. Enter “fritz.box” in the “Hostname or IP address:” field.
Sharing a USB Printer 5. Click the “Standard TCP/IP Port” entry and click “New Port”, then “Next”. 6. Enter “fritz.box” in the “Printer Name or IP Address” field. If the FRITZ!Box is configured as a wireless repeater or an IP client, enter here the IP address at which the FRITZ!Box can be reached within the network. 7. Enter any name you wish in the “Port Name” field and click “Next”. 8. Select the “Custom” option and click “Settings...”. 9. Enable the “Raw” option. 10.
Sharing a USB Printer 7. In the “Print Using:” drop-down list, select the printer that is connected to the USB port of your FRITZ!Box. If the printer is not displayed, you must first install the printer drivers for this device. Consult the documentation of your printer for instructions. 8. Click “Add”. The USB printer has been configured and can be used as a network printer.
Sharing a USB Printer 2. Open the FRITZ!Box user interface; see page 33. 3. Enable the advanced view. 4. Select the “Home Network / USB Devices / USB Remote Connection”. 5. Click the “USB remote connection software” link. 6. In the “USB Remote Connection” window, click “Download”. 7. Download the file “fritzbox-usb-fernanschluss.exe”. 8. Double-click the file and follow the instructions on your screen. The FRITZ!Box USB remote connection software is now installed on your computer.
Sharing a USB Printer Using a USB Printer with FRITZ!Box USB Remote Connection 1. Open the FRITZ!Box USB remote connection by clicking the icon in the Windows task bar. 2. Enter the FRITZ!Box password in the “My FRITZ!Box” area. 3. Click “Refresh”. 4. Click the USB printer in the “Devices” area. The USB printer is being connected to the computer. Do not conduct any FRITZ!OS updates for USB devices that are connected with the computer via the FRITZ!Box USB remote connection.
Managing Memory with FRITZ!NAS 20 Managing Memory with FRITZ!NAS With FRITZ!NAS you can display the data on the storage media of your FRITZ!Box in a clearly arranged interface. All participants in the FRITZ!Box home network can start FRITZ!NAS in a web browser and use it as a platform to access music, images, videos and documents in the FRITZ!Box memory. 20.
Assigning FRITZ!Box Name 21 Assigning FRITZ!Box Name You can assign an individual name for your FRITZ!Box in the FRITZ!Box user interface.
Controlling Smart Home Devices 22 Controlling Smart Home Devices With smart home devices from AVM you can automate tasks in your household and control them over the Internet. AVM smart home devices can be inserted in any outlets and connected wirelessly with the FRITZ!Box. All connected smart home devices can be configured directly at “Home Network / Smart Home” in the FRITZ!Box user interface, for instance, to automatically switch on and off a lamp and measure its energy consumption.
Configuring Internet Access for Guests 23 Configuring Internet Access for Guests With the FRITZ!Box you can provide houseguests with an Internet connection of their own. At this guest access they can surf the web with their own devices, but cannot access the contents of your home network. 23.1 Requirements The guest access in the FRITZ!Box can be configured and provided only if the FRITZ!Box establishes the Internet connection itself.
Configuring Guest Access on the LAN 4 Port 3. Assign a name for the guest wireless network (SSID) and enter a network key under “Security”. This concludes the setup of your guest access. Now guests can register their wireless devices with the FRITZ!Box. Registering a Wireless Device with the Wireless Guest Access 1. Your guest starts the wireless LAN software of his or her wireless device and searches for the guest network. 2. Your guests authorizes themselves using the network key you assigned.
Help in Case of Errors 24 Help in Case of Errors Here you can find assistance if no DSL connection is established, if the FRITZ!Box cannot be opened, or if errors occur with wireless LAN connections. For more help, see the AVM Knowledge Base in the Internet: 24.1 DSL Connection Not Established If the “Power / DSL” LED keeps flashing, the FRITZ!Box cannot establish a DSL connection. Make sure the correct DSL variant (annex) is set in your FRITZ!Box. Setting the DSL Variant (Annex) 1.
The User Interface Does Not Open 24.2 The User Interface Does Not Open If the FRITZ!Box user interface cannot be opened, this can have various causes. Work through the following steps in sequence until the error has been resolved. Entering http://fritz.box in the Web Browser Enter http://fritz.box in the web browser instead of fritz.box. Google Chrome, for instance, performs a Google search if the address of the FRITZ!Box is not known and entered incompletely. Restarting the FRITZ!Box 1.
The User Interface Does Not Open Internet Explorer 1. Click “Tools” and select “Internet options”. 2. On the “General” tab, click the “Delete...” button in the “Browsing history” area. 3. Enable the “Temporary Internet files” option and click “Delete”. Google Chrome 1. Click the Chrome menu (“Customize and Control Google Chrome” button) and select “History / Clear browsing data...”. 2. Select “the beginning of time”, and below it only the option “Cached images and files”. 3.
The User Interface Does Not Open Internet Explorer 1. Click “Tools” and select “Internet options”. 2. Switch to the “Connections” tab and click the “LAN settings” button. 3. If the “Use a proxy server for your LAN” option is enabled, click “Advanced”. Under “Exceptions” enter the address “fritz.box” and click “OK”. If no proxy server is used, click “Cancel”. Google Chrome Check whether the use of a proxy server is enabled. If so, enter “fritz.box” as an exception in the proxy server settings.
Cannot Establish a Wireless LAN Connection 3. Make sure that the computer obtains its IP address automatically; see page 141. 4. Clear all other connections between your FRITZ!Box and other network devices. 5. In the web browser, enter the address 169.254.1.1. 6. When the FRITZ!Box user interface is displayed, enable the DHCP server of the FRITZ!Box: In the user interface, select “Home Network / Network / Network Settings”.
Cannot Establish a Wireless LAN Connection Announcing the Name of the Wireless Radio Network If the wireless LAN software on your computer cannot find the wireless radio network of the FRITZ!Box, make the following setting in the FRITZ!Box: 1. Connect a computer to the FRITZ!Box with a network cable; see page 27. 2. Open the FRITZ!Box user interface; see page 33. 3. Select “WLAN / Radio Network”. 4. Enable the option “Name of the radio network visible”. 5. Click “Apply”. 6.
Wireless LAN Connection Interrupted 24.4 Wireless LAN Connection Interrupted If the wireless LAN connection between your computer and the FRITZ!Box is disrupted, this may be due to a variety of causes. Work through the following steps in sequence until the error has been resolved.
Configuring FRITZ!Box on the Telephone 25 Configuring FRITZ!Box on the Telephone Various functions can be configured using a telephone connected to the FRITZ!Box. 25.1 Alarm Requirements • You set up an alarm in the FRITZ!Box; see Alarm on page 121. Can I Switch More than One Alarm On and Off? No. With the telephone keys you always switch on or off the first alarm.
Do Not Disturb 25.2 Do Not Disturb For the lines “FON 1” and “FON 2” you can enable the Do Not Disturb feature. In the FRITZ!Box user interface you can also configure the Do Not Disturb function for other telephones; see Do Not Disturb on page 121. Timetable and Do Not Disturb for Other Telephones In the FRITZ!Box user interface you can also configure the Do Not Disturb function for other telephones; see Do Not Disturb on page 121.
Call Diversion 25.3 Call Diversion Call diversion automatically diverts incoming calls to a previously specified external telephone number. If your telephony provider supports this, calls will be diverted by your provider. Otherwise the FRITZ!Box establishes a second connection. In either case, extra charges will accrue according to your contracted telephone rates.
Call Diversion Enabling: Call Diversion for Own Telephone Number You can set up call diversion that applies only for all calls that arrive for a certain telephone number. Calls for your other telephone numbers will not be diverted. Here is how to configure call diversion to an external number (destination number): 1. 2.
Call Diversion Enabling: Call Diversion for FON 1 1. Press the following keys on the telephone: Type of Call Diversion Keys Immediately without ringing r411ss Immediately with ring r451ss Delayed (after 20 seconds) r421ss Only when busy r431ss Immediately when busy, oth- r441ss 2. Pick up the handset. Wait for the second-long positive acknowledgment tone. 3. Hang up the handset.
Switching the Wireless Network On and Off Enabling: Call Diversion for FON 2 1. Press the following keys on the telephone: Type of Call Diversion Keys Immediately without ringing r412ss Immediately with ring r452ss Delayed (after 20 seconds) r422ss Only when busy r432ss Immediately when busy, oth- r442ss 2. Pick up the handset.
Loading Factory Settings 25.5 Loading Factory Settings All settings you made in the FRITZ!Box will be deleted. 1. Press the keys r991s15901590s. 2. Pick up the handset and hang it up again. The factory settings are loaded. Then the FRITZ!Box will restart. 25.6 Disabling and Enabling Automatic Outside Dialing On the “FON 1” and FON 2 lines you can enable and disable automatic outside dialing. The default setting is “enabled”.
Disabling and Enabling Automatic Outside Dialing Automatic Outside Dialing on FON 2 1. 2. FRITZ!Box 7272 Press the following keys on the telephone: Function Keys Disable automatic outside dialing r12s0s Enable automatic outside dialing r12s1s Pick up the handset and hang it up again.
Taking FRITZ!Box Out of Operation 26 Taking FRITZ!Box Out of Operation In this chapter you receive tips and recommendations for taking the FRITZ!Box out of operation. 26.1 Loading Factory Settings When the factory settings are restored to the FRITZ!Box, all of the settings in the FRITZ!Box are restored to their condition upon delivery. This way you can delete incorrect settings that prevent the FRITZ!Box from functioning properly.
Uninstalling Supplementary Software Load Factory Settings Before loading factory settings, we recommend saving the settings configured on your FRITZ!Box in a backup file; see page 41. 1. In the FRITZ!Box user interface, select the “System / Backup” menu. 2. Select the “Factory Settings” tab. 3. Click the “Load Factory Settings” button. The FRITZ!Box is reset to its factory settings. All settings made during operation will be overwritten. 26.
Uninstalling Supplementary Software Uninstalling Programs in Windows 7 1. Open “Start / Control Panel / Programs”. 2. Under “Programs and Features”, click “Uninstall a program”. 3. Mark the AVM program you want to remove in the list. 4. Click the “Uninstall/Change” button. The program will be removed. Uninstalling Programs in Windows Vista 1. Open “Start / Settings / Control Panel / Programs and Functions”. 2. Mark the AVM program you want to remove in the list. 3.
Technical Specifications 27 Technical Specifications Facts worth knowing: Here you will find comprehensive technical data on your FRITZ!Box 7272. 27.1 Ports and Interfaces • DSL/telephone port – ADSL/ADSL2/ADSL2+ modem (also IP-based, Annex J), or alternatively ITU G.992.1, ITU G.992.3 or ITU G.992.
Router Functions 27.2 Router Functions • • • • • • • • 27.3 27.4 27.
Cables • • Maximum power consumption: 16 W Average power consumption: 6 W – 8 W The average power consumption was determined at room temperature (23 °C to 27 °C) with the following load: – DSL connection active – wireless LAN on; no devices registered via wireless LAN – DECT on; one telephone registered via DECT; no active calls – one network device connected to a LAN port; no data transfer; other LAN ports not in use 27.
Cables You can extend one or both ends of the network cable. You will need the following components to extend the cable: • Standard Cat-5 network cable, type STP (shielded twisted pair) – When components of a category smaller than Cat 5 are used, reduced transmission rates may result. – You can use both straight cables and crosslink cables. • 1 standard RJ45 CAT-5 double coupling with a 1:1 pinout All components are available from specialized vendors. Replacement The network cable is a standard cable.
Customer Service 28 Customer Service Be it product documentation, frequently asked questions, tips or support: This chapter presents information on all important service topics. 28.1 Documentation on the FRITZ!Box To take advantage of all commands and features of your FRITZ!Box, consult the following documentation: Help In the FRITZ!Box user interface you can open the comprehensive Online Help by clicking the “Help” icon and the “Help” buttons.
Feedback on FRITZ!Box AVM Knowledge Base In our AVM Knowledge Base you can find answers to your questions and specific solutions to your problems. The AVM Knowledge Base is located in the “Service” area of the AVM web site: en.avm.de/nc/service/fritzbox/fritzbox-7272/knowledgebase 28.3 Feedback on FRITZ!Box In various places in the user interface, the FRITZ!Box offers you the opportunity to send your concrete feedback to AVM. Your feedback helps us to continually improve the FRITZ!Box.
Assistance from the Support Team Evaluating the Voice Quality of Internet Calls In the advanced view of the FRITZ!Box (see page 35), the “Telephony / Own Telephone Numbers / Voice Quality” page offers you the opportunity to evaluate the quality of the Internet call. Your evaluation will help us continue to improve the quality of voice transmission in Internet calls made over the FRITZ!Box. The contents of the call and numbers participating will not be transmitted to AVM. 28.
Assistance from the Support Team Support by e-mail You can send us an English-language e-mail request at any time using the “Service” area of our web site. You can reach the service area at en.avm.de/service/support-request/your-support-request. 1. Select the product group and your product for which you need support from the “Support” area. You will receive a selection of FAQs. 2. If you need more help, click the “Contact Support” button to open the e-mail support form. 3.
Manufacturer’s Warranty 28.5 Manufacturer’s Warranty We offer a manufacturer’s warranty of 5 years on the hardware of this original product. The warranty period begins with the purchase date from the first end user. Compliance with the warranty period can be proven by submission of the original invoice or comparable documents. This warranty does not restrict your warranty rights based on the contract of sale or other statutory rights.
Legal Notice Legal Notice This documentation and the software it describes are protected by copyright. AVM grants the nonexclusive right to use the software, which is supplied exclusively in object code format. The licensee may create only one copy of the software, which may be used exclusively for backup use. AVM reserves all rights that are not expressly granted to the licensee.
Declaration of CE Conformity The manufacturer AVM GmbH Alt-Moabit 95 D 10559 Berlin Germany herewith declares that the product FRITZ!Box 7272 ADSL-WLAN router complies with the following directives: 1999/5/EC R&TTE Directive: Radio Equipment and Telecommunications Terminal Equipment 2009/125/EC EU directive: ecodesign requirements for energy-related products 2011/65/EU EU directive: on the restriction of the use of certain hazardous substances in electrical and electronic equipment The following norms
Disposal Information In accordance with European regulations, the FRITZ!Box 7272, as well as all devices and electronic components contained in the package, may not be disposed with household waste. After use, please dispose of FRITZ!Box 7272 and all electronic components and devices included with delivery at a collection point in your local community for the disposal of electric and electronic appliances.
Drilling Template A drilling template is presented below. Use the drilling template as a guide to mark the holes needed to mount the FRITZ!Box on a wall. This page must be printed out at a size of 100%. Do not enlarge it, adjust its size, reformat or rescale it in your printer settings.
Index A connecting answering machine . . . . . . . . . . . . 52 behind modem . . . . . . . . . . . . . 23, 48 behind router . . . . . . . . . . . . . . . . . 24 computer. . . . . . . . . . . . . . . . . . . . . 27 door intercom system . . . . . . . . . . 56 DSL . . . . . . . . . . . . . . . . . . . . . . . . . 20 electrical power . . . . . . . . . . . . . . . 19 fax machine . . . . . . . . . . . . . . . . . . 52 hub/switch . . . . . . . . . . . . . . . . . . . 28 landline . . . . . . . . . . . . . . . . .
D F declaration of CE conformity . . . . . . . 187 DECT base station . . . . . . . . . . . . .14, 132 DECT button. . . . . . . . . . . . . . . . . . . . . . 15 DECT cordless telephone deregistering. . . . . . . . . . . . . . . . . 132 paging . . . . . . . . . . . . . . . . . . . . . . 132 registering . . . . . . . . . . . . . . . . . . . . 53 DECT Eco . . . . . . . . . . . . . . . . . . . . . . . 133 device properties . . . . . . . . . . . . . . . . 178 DHCP server (integrated) . . . . . . . . . .
G I green AP (wireless LAN) . . . . . . . . . . . . 37 green mode (LAN) . . . . . . . . . . . . . . . . . 38 guest access LAN4 . . . . . . . . . . . . . . . . . . . . . . . 158 see guest network . . . . . . . . . . . . 157 wireless LAN . . . . . . . . . . . . . . . . . 157 guest network configuring . . . . . . . . . . . . . . . . . . 157 imprint . . . . . . . . . . . . . . . . . . . . . . . . . 186 information in the Internet knowledge base . . . . . . . . . . . . . . 182 videos . . . . . . . . . . . . .
L notice legal. . . . . . . . . . . . . . . . . . . . . . . . 186 notifications . . . . . . . . . . . . . . . . . . . . . 39 LAN connecting . . . . . . . . . . . . . . . . . . . 27 guest access . . . . . . . . . . . . . . . . . 158 landline connecting . . . . . . . . . . . . . . . . . . . 25 telephone number . . . . . . . . . . . . 125 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 legal notice . . . . . . . . . . . . . . . . . . . . . 186 LISP . . . . . . . . . . . . . . . . . . . . . .
S T saving data . . . . . . . . . . . . . . . . . . . . . 174 saving electricity . . . . . . . . . . . . . . . . . . 36 schedule . . . . . . . . . . . . . . . . . . . .37, 104 security FRITZ!Box password . . . . . . . . . . . . 60 FRITZ!Box user account . . . . . . . . . 62 FRITZ!OS update . . . . . . . . . . . . . . . 43 installing and connecting . . . . . . . . 8 password protection . . . . . . . . . . . 59 saving settings . . . . . . . . . . . . . . . . 41 VPN . . . . . . . . . . . . . . . . . . . . .
U W UMTS Internet access . . . . . . . . . . . . . . . . 48 Internet connection . . . . . . . . . . . . 23 substitute connection . . . . . . . . . . 99 uninstalling programs. . . . . . . . . . . . . 175 uninstalling supplementary software 175 update . . . . . . . . . . . . . . . . . . . . . . . . . . 43 updating firmware. . . . . . . . . . . . . . . . . 43 usage data. . . . . . . . . . . . . . . . . . . . . . . 39 USB accessing memory . . . . . . . . . . . . 146 hub . . . . . . . . . . . . . . . . . . . .
