Digital Super Hybrid System Getting Started Model No. KX-TD612 Thank you for purchasing a Panasonic Digital Super Hybrid System, Model KX-TD612. Before connecting this product, please read this manual carefully and save this manual for future use.
Contents Preparation Page 3 Connections Page 4 Basic Programming Page 7 PC Programming Page 11 Information on the CD-ROM Page 16 2 Describes the included accessories and required tools for installation. Shows you how to install your system. Describes the basic programming to make/ receive calls. Describes how to set the system programming by a personal computer (PC). Shows the contents of the CD-ROM.
Preparation Before installing your system Check the package contents. The included materials and numbers included are: Main Unit ........... 1 Getting Started (This manual) ........... 1 CD-ROM (Including Manuals, etc.) ........... 1 Template (for wall mounting) ........... 1 AC Cord [PSWAT206E] ........... 1 10-pin Terminal Block [PSJS10S07Z] ........... 1 (for external equipment) Screws [PQHE5004Z] and Washers [XWG35FY] ........... 3 Pin Plugs [PQJP1E1Z] ...........
Connections System Connection Diagram 3 ISDN (BRI) Lines To ISDN (BRI) port 1 and 2 (initial) To ISDN (BRI) port 3 (additional) (Lightning Protectors) 1 Analogue CO Line (optional) Car Batteries External Music Source Printer or Computer External Relay Amplifier Second Ringer Relay Speaker 12 Extension lines Single Line Telephone KX-T7436 KX-T7433 Door Openers Cordless Phone KX-T7431 KX-T7440 German type Doorphone Facsimile Panasonic VOICE PROCESSING SYSTEM KX-TVP50 POWER Voice Processing
Connections Extension Connection Use 8-pin terminal blocks (included) to connect the extension lines. Extension jacks 1 to 4 are available for eXtra Device Port (XDP) connection. Extension jacks 5 to 8 are only for digital proprietary telephones. 1. While pressing down on the hole at the top of the terminal block using a small flat type screwdriver, insert the required telephone wire into the side hole as shown below.
Connections CO Line Connection 1. Insert the modular plugs of the ISDN (BRI) CO line cords (8-conductor wiring) into the ISDN (BRI) ports 1 and 2. 2. Connect the line cords to the terminal board or the modular jacks from the Central Office. To Terminal Board or Modular Jacks from the Central Office ISDN (BRI) ISDN (BRI) ISDN (BRI) Port 1 Port 2 Port 3 TA RA RB TB A. When your system is at the end of the connection Terminal Equipment 7 Network Terminal Termination Equipment 1 To Central Office B.
Basic Programming Before Programming This chapter describes system programming necessary to enable receiving/making an outside call. Setting Status of Extension: ISDN (BRI) port 1, Jack 1-1 (Extension no. 201) The following items are required before the programming Confirm your ISDN telephone number. Confirm whether your connection type is point-to-point or point-to-multipoint. Connect a digital proprietary telephone (DPT) with display (e.g. KX-T7436, KX-T7433, etc.) to the Jack 1-1.
Basic Programming Basic Programming [001] System Speed Dialling and Intelligent Call Handling Number Set 1. Dial 0 0 1 2. Press NEXT. . SYS-PGM NO?→ SPD & CH Number SE NEXT CLR 4. Enter your phone number. 500:Not Stored → SKP+ SE NEXT CLR 5. Press STORE 500: → SE NEXT SEL 3. Dial . 0123456789 SE NEXT SEL 5 0 0 . SPD&CH Cod? SKP+ CLR S E NEXT 6. Press NEXT. 500: 0123456789 SKP+ SEL S E NEXT END 7. Repeat steps 4 though 6 until you store all of your phone number. 8.
Basic Programming [423] ISDN Layer 1 Active Mode 4 1. Dial 2 3 2. Press NEXT. . NO?→ SYS-PGM CLR L1 NEXT Active SKP+ 3. Dial CLR Mode 1 . NO? → Port NEXT SKP+ CLR NEXT END STORE 4. Press . OR 4. Press SEL+ and then STORE press #1 :Permanent → SEL+ #1 . . :Call → NEXT 5. Press SEL+ NEXT [424] ISDN Configuration 1. Dial 1 4 2 SYS-PGM 1 4 2. Press NEXT. .
Basic Programming [425] ISDN Data Link Mode 4 1. Dial 2 5 2. Press NEXT. . NO?→ SYS-PGM CLR Data NEXT STORE 4. Press Link SKP+ SEL+ . NO? → Port NEXT SKP+ CLR S E NEXT . OR :Permanent → Mode CLR END 4. Press SEL+ and then press #1 1 3. Dial #1 STORE . . :Call → NEXT 5. Press SEL+ NEXT [426] ISDN TEI Mode 1 4 1. Dial 2 SYS-PGM 1 6 2. Press NEXT. .
PC Programming System Requirements Before installing the PC programming software, be sure to read the following information. System Requirements: - Microsoft® Windows® 95, Windows 98, Windows Me, Windows 2000 or Windows NT® 4.0 or later - Installation of Internet Explorer 4.
PC Programming PC Installation The PC is used for system programming. Connect the Serial Interface (RS-232C) connector of the PC to the Serial Interface. (A printer can be connected to the system in the same way.) Serial Interface (RS-232C) (D-SUB, 9-pin) Serial Interface (RS-232C) Connector (user-supplied) The cables must be shielded and the maximum length is 2 m. Refer to the following charts for the pin configuration. Port on your system 9-pin port on a PC Pin No. Pin No.
PC Programming PC Programming You can set system programming by PC. An example is shown below. Please change the language on the window of the PC programming software when installing. To enter the programming mode 1. Choose Connect in menu, and then click Local(RS-232C). 2. Enter the password. You can change the password in programming [107] System Password (Default: 1234). 3. Click OK.
PC Programming [001] System Speed Dialling and Intelligent Call Handling Number Set 1. Click Load from PBX. 2. Click OK to start uploading automatically. 3. System Program Menu screen is displayed. Double-click Speed Dial & Call Handling. 4. After entering telephone numbers and names, Click OK to store them.
PC Programming To exit the programming mode 1. After finishing all the necessary programming, click Save to PBX. 2. Click OK to start downloading automatically. 3. Click Exit. 4. Click OK. 5. Click OK.
Information on the CD-ROM You can find electronic documentation for the KX-TD612 System, created in Portable Document Format (PDF), on the attached CD-ROM. Before you begin using the PDF documents, be sure to read the following information. Once you insert the KX-TD612 CD-ROM into your CD-ROM drive, an html file will start up automatically. Following the installation wizard, please select the PBX model you have, the language you want, and the manual you need.
