Phoenix2 Rev.
Table of Contents 2 Phoenix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Remote Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Electronic Scan Prevention (ESP). . . . . . . . . . . . . . . . . . . . . 3 Instant Remote Control Code Deletion. . . . . . . . . . . . . . . . . . 3 One-Step Remote Control Code Learning . . . . . . . . . . . . . . . . 3 Valet Switch . . . . . . . . . . . . . .
Phoenix2 Congratulations! You have just purchased the Phoenix2 vehicle security system manufactured by Avital Technologies, Inc. To fully benefit from the capabilities of your system, we encourage you to read the Owner’s Manual thoroughly before using the system. If you have any problems or questions regarding your system, consult the dealer from whom you purchased this product. To locate an authorized Avital dealer, contact Avital Technologies directly at 1-800-253-0334 (toll-free within the U.S.
Electronic Scan Prevention (ESP) Your system includes ESP, which blocks electronic scanner codes preventing unauthorized operation of your system. Instant Remote Control Code Deletion In the event of a lost or stolen remote control, all remote controls can be erased from the system’s memory preventing unauthorized system operation. (See the "Programming Table for Remote Controls" on page 12). One-Step Remote Control Code Learning Your system allows you to add new remote controls in one step.
Operating Instructions To Arm The System The alarm can be programmed for active or passive arming. Active arming means the alarm can only be armed by the remote control. Passive arming means the alarm will automatically arm itself. (See the "Programming Table for System Features" on page 11.) Active Arming Press the remote ARM/DISARM button for 1-2 seconds. The siren will chirp twice, the parking lights will flash twice, the doors will lock, the LED will flash slowly and the starter will be disabled.
User-Programmable Long-Term Silent Arm/Disarm This feature allows you to completely disable the arm/disarm siren chirps until you decide to restore them. (See the "Programming Table for System Features" on page 11.) Two-Stage Unlock Capability If the optional Two-Stage Unlock feature was installed, press the remote ARM/DISARM button for 1-2 seconds and only the driver door will unlock.
User-Programmable Ignition-Controlled Door Lock/Unlock For the ultimate in security and convenience, the system is programmed to automatically lock your doors when the ignition key is turned "ON" or the engine is started, and will unlock when the ignition key is turned "OFF." This feature can be programmed ON or OFF. (See the "Programming Table for System Features" on page 11.
To Deactivate Remote-Controlled Valet 1. Press the remote ARM/DISARM and SILENT buttons at the same time. 2. The parking lights will flash 3 times. 3. The LED will turn off to indicate the alarm is no longer in Remote-Controlled Valet. Keyless Entry in Valet Mode While the system is in the Valet mode, you can still use your remote control to lock and unlock the doors as well as activate any optional accessory such as trunk release or remote engine starter.
Remote-Controlled Sensor Bypass You can bypass the system sensor(s) at any time. The alarm system will still provide full perimeter protection. To Bypass the Sensor(s): 1. Press the remote TRUNK and OPTION buttons at the same time. 2. The siren will chirp twice. . . pause. . . chirp twice. . . pause . . . chirp twice. 3. The sensor(s) is now bypassed until you remotely disarm and then re-arm your system.
User-Programmable Siren Duration Upon activation, the siren can be programmed to run for 30 or 60 seconds before it will shut off and instantly rearm. (See the “Programming Table for System Features” on page 11.) Alarm State Memory If your vehicle battery is disconnected and later reconnected, the system will automatically return to its last state before power was removed, whether it was armed, disarmed or in Valet Mode.
User-Programmable Features All system and remote control programmable features are accomplished by turning the ignition key "ON" (or starting the engine) and flicking the valet switch on and off a preset number of times. The system also allows you to add new remote controls in one step, delete lost or stolen remote controls or rearrange the factory preset remote control functions. 1. Remove the system from Protected or Remote-Controlled Valet mode.
Programming Table for System Features Feature Factory Setting No. of Chirps Secondary Action Active / Passive Arming Passive 4 Wait 3 seconds, the siren will chirp once for Active, twice Passive. Passive Door Lock OFF 5 Wait 3 seconds, the siren will chirp once for OFF, twice for ON. Passive Armed Confirmation ON 6 Wait 3 seconds, the siren will chirp once for OFF, twice for ON. Ignition-Controlled Door Lock / Unlock ON 9 Wait 3 seconds, the siren will chirp once for OFF, twice for ON.
Programming Table for Remote Controls Feature Factory Setting No. of Chirps Secondary Action Arm/Disarm ARM/DISARM Button 15 Press the ARM/DISARM button, the siren will chirp 1 time. Remote-Controlled Trunk Release Output TRUNK Button 16 Press the TRUNK button, the siren will chirp 2 times. Remote-Controlled Silent Arm/Disarm SILENT Button 17 Press the SILENT button, the siren will chirp 3 times.
Phoenix2 Rev.
© 1999 Avital Technologies, Inc. Part Number: 31-1270 Rev. A Phoenix 2 Rev.
