USB Net Power 8800 Manual Release Date: 11/12/2010 Manual Version:1.
Table of Contents Welcome ........................................................................................................................ 3 Introduction ........................................................................................................... 3 Minimum System Requirements............................................................................ 3 Product Overview ..........................................................................................................
Welcome Introduction The USB Net Power is an economical device for network power control. With this device power control could not be any easier. Simply plug in the device, run the software and now anyone can turn on turn off their devices via the PC. Also with a scheduler function included this device can easily become automated to turn on and turn off anything connected.
Product Overview Features 1. Remote & Local power control: Turn ON / OFF devices. 2. Control through any other PC on Internet. 3. Timer Scheduler: Preset the time to control power on / off 4. Exchangeable Fuse Protection. 5. SDK Available 6. User friendly, compact, and simply just plug & play.
Package Contents 8800 Device x 1 USB Cable USB cable that is used to connect the 8800 to the computer that will be controlling the device. Installation CD Comes with drivers, manual, and software. Extra Fuse Extra fuse is provided.
Product Interface Hardware Interface Front View The front view of the 8800 consists of a USB port that allows you to connect the 8800 to the computer. Back View On the back of the device there will be a fuse section and the Power Input cord that will be connected to your power source.
Replacing the Fuse The specs for the device are the following: Model: USB Net Power 8800 Input Voltage Range: 100V ~ 240V Maximum Current: 6A Weight: 300 grams Dimensions: 85mm x 85mm x 50mm Operation Temp: 0℃~50℃, (32℉ ~120℉) Fuse Specs: European Standard: 6.3A American Standard:6A If you find that the device is not working correctly you may check the fuse to see if it is still intact. To replace the fuse on the device please follow the following directions. 1.
Software Installation Instructions The software for the device is located on the Media Link-IP Family CD that came with the device. Please follow the directions carefully and install the necessary files 1.) First place the Media Link-IP Family CD that came with your device into your CD/DVD Rom drive. The CD should auto run but if it does not go to the CD/DVD Rom drive and select the file “autorun.html”.
2.) Select the Usb Net Power 8800 in the USB Series section. 3.) Download the following software and save them to the appropriate locations. a. USB Net Power – The USB Net Power software is specifically used to control the device, set a schedule, and setup remote control b. IP Power Center – This software is used to manage IP Power products. It allows a easy way to control devices c. USB Net Power Driver – The driver must be installed for the device to work correctly when connected to a computer. 4.
Software Interface Date & Time The date and time section will automatically synchronize the time and date with the computer that is being used. This time will be used to setup the scheduler for the device so that it can correctly turn on and off devices at the desired times. Scheduler The scheduler allows you to schedule events when your device will turn on / turn off. This creates a very powerful tool, in that all your power needs can become automated.
Start Date: Choose the date of when you want the device to turn on or off. Simply type in the date you would like or click on the dropdown menu to present the calendar. Then simply click on the desired date. End Date: Choose the date when you want the event to stop happening. Time: Select the time when the device will activate. Command: The action that is desired during the specified date and time. Create Event To create a new event, follow the following steps: 1.
everyday at the desired time until the end date has been reached. 3.) Then select a Time and for the command choose on or off 4.) Once everything has been set make sure to hit the New button to add this new event to your scheduler Edit Event To edit an existing event, follow the following steps: 1.) Click on the event located in your scheduled events section that you would like to edit 2.) Then you change the values the different fields for the Start date, End date, Time, & Command. 3.
To the right side of the program you will see a message log that will keep track of power statuses being used. It will report the time and status so that you can easily keep track of your power status. Remote Settings The remote setting section is where you can setup the device so that it can be controlled from outside the network. This means as long as the computer with the 8800 is attached and the software is running you will be able to control the device from a remote location.
Logs & Messages The logs and messages section will basically keep track of the actions of your device. It will state the time and action that was performed at that time. Clear Logs The clear logs button will clear the logs section of the software. Simply just click on the Clear Logs button. Update Software When there is an update for the device software, the update button will become activated. Simply click on the update button and the software will automatically update itself.
Controlling Power Remotely Using Mac With CNT technology connecting to your device without any type of port forwarding has become easy. When you select this option to control the device using Mac you will be required to use this following program: - IP Power Center With IP Power center you can connect to your device from any networked location. By searching for the name of your device you can easily find the device in the network and control it from another computer.
3.) Type the username of your device and click the search button. Then your USB Power will appear. Double click on the device name and a login window will open 4.) Type in the correct the username and password and click the add button to add to IP Power Center 5.) Then expand the group device section and you will find your device there. Right click on the device and select the command of choice.
Using GAE GAE adds a new way to remotely control the USB Net Power. With the power google cloud computing, this GAE functionality allows you to control the USB Net Power from any remote location with internet. To use this functionality simply follow the following steps: 1.) Setup the USB Net Power to accept GAE and hit the send button. 2.) Then after you have sent the login information you can upload an image so that your device is easy to find.
4.) In the link provide type in the user name of your device and click the search button. 5.) Click on your device and a login page will appear to connect to your device. 6.) Then type in the username and login password for your device and press the send button. By default: Login: usbpower Password: 12345678 7.) Once you are connect to your device you can now turn on or turn off the device via a remote location.
FAQ FAQ 1.) Question: How come the relay is not working on the device? Answer: There could be numerous reasons why the relay is working incorrectly. Check the plug to make sure it is plugged in correctly. If not you may need to check the fuse, make sure the device is unplugged before checking the fuse for your safety. 2.) Question: How can I change the fuse on the device? Answer: Please visit page 7 on the manual to learn how to change the fuse on the USB Net Power 3.
