IP Kamera 9070-IR User Manual Release Date: 10/20/2009 Manual Version: 1.
Warning: Any changes made to this equipment without permission may cause damages to the device! IMPORTANT NOTICE 1. IP Kamera 9070-IR was designed for outdoor/ indoor. 2. Please use the power adapter provided by the dealer, the manufacturer is not responsibility for the possible damage from using power adapters. 4. Do not shake the IP Kamera 9070-IR in any fashion 5. Please contact the dealer If IP Kamera 9070-IR is not working properly. Copyright © 2008 All rights reserved.
Table of Content INTRODUCTION ............................................................................................................................ 5 MINIMUM SYSTEM REQUIREMENTS ................................................................................................. 5 2.) PRODUCT OVERVIEW .......................................................................................................... 6 FEATURES ........................................................................................
NETWORK ................................................................................................................................ 26 NETWORK ......................................................................................................................................... 26 FTP ................................................................................................................................................. 27 SMTP (OUTGOING E‐MAIL SERVER) ........................................
1.) Welcome Introduction The IP Kamera 9070-IR provides reliable, high quality solution to IP Kameras. Its distinctive 720P HD quality picture, Tri-mode video capability, built in SD memory storage, RTSP broadcasting capability, internal microphone and many more functions makes this small device very powerful and unique. The built in web server of the IP Kamera 9070-IR will allow the IP Kamera to be viewed from any remote locations around the world while bringing ease of mind.
2.) Product Overview Features 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. Tri-Mode Camera (MPG4-1/MPEG4-2/M-Jpeg) Advance Motion detection trigger AVI /Jpeg save on FTP / SD card or Email 3 layers (Admin, Operator, and User) Password protected Resolution from CIF 352x192 up to HD 1280x720P Supports NTP protocol to get correct time schedule. 1/2.5” Advance CMOS sensor, with highly sensibility for quick response insufficient lighting.
Package Contents 1.) 9070-IR Unit x 1 with Lid 3.) 9070-IR Installation CD 4.) AC Adaptor (AC adaptor will be included and will correspond to the countries power standards) Specs: Input: 100-250Vac /47-63Hz, 1A Output: 12Vdc/1A Max: 12W 5.
3.) Interface Description Cable Description Cables DC 12 V Power Input: Plugs in the Power Adapter to the DC 12V Card RJ45 Ethernet: Plug in the RJ45 Ethernet cable to the Ethernet Reset Button: Reset to Manufacturer Default: Hold Reset button for 5-10 Seconds and the device will reset to manufacturer default. Video Out: The Video out requires a BNC connector to output video to a different source. Built In SD Card Built in 512MB SD Memory Card. 4.
Internet Accessible Setup The internet connection can be setup in two main ways so that the 9070-IR can be accessed through the internet The network uses a Router/Firewall to connect each device to the internet In this case, the 9070-IR will need to be port forwarded on the router so that it can accessed by the internet. For example 9070-IR IP Address: 192.168.1.882 9070-IR Port: 9070 On the router that is being used port forwarded (port triggered) IP Address 192.168.1.882 and port 9070.
In this case, the 9070-IR is being connected to the internet through a hub, which is different from a router. The hub does not provide DHCP, and therefore would require that this setup have a static IP Address that is provided by the ISP. Contact the ISP to find out the static IP address so that your device can be accessed through the internet. Once a Static IP has been assigned the device will be able to automatically go onto the internet. . 5.
3.) Download the following software and save them to the appropriate locations. a. IPEdit - Device search tool which allows you to modify IP settings, find your on the local network and IP Service. b. Surf 16 CH – 16 Channel DVR, Monitoring, & Recording Software. Views up to 16 channels on one screen. 4.) Once installation is complete please double click the IPEdit to configure and search for your device.
2.) Open IPEdit and any device in the same network should automatically be detected and listed in the local devices sections. Note: If the device is not showing up, please hit the rescan button and wait about 1 minute Setup the Device: All devices will need to be on the same network if not the device cannot be accessed and will not be detected. Quick Easy Setup (Recommended) 1.) Click on the REF button, and wait a few seconds. IPEdit will automatically detect the network settings and setup the device. 2.
3.) Hit yes to confirm and Enter the login and password for the Device to Approve changes 4.) Then hit the rescan button on IPEdit to confirm the changes have been made. Custom Setup (Advance Users) 1.) Highlight the device on the local devices section and on the right side of IPEdit all network information on the device will be displayed.
2.) To setup the device, you will need type in the correct Gateway and IP Address. The Gateway Address: The gateway address can be obtained in Windows under the network connections page IP Address: Make sure the first 3 sections of the IP Address matches the gateway address. Example: Gateway Address – 192.168.1.1 IP Address – 192.168.1.xxx 3.) Once the Default Gateway information has been obtained, enter the correct information into IPEdit and hit the submit button. 4.
IP Service How to use IP Service on IPEdit: IP service allows the user to directly connect to his / her device through the internet without having to remember long confusing IP Address. Instead you only need to remember the name of the device that the you have selected. Then the user can connect to IP Service, type in the device name, and connect directly to the device. Note: The IP Kamera 9070 requires you to select Server 2 on IP Service 1.
Default IP: 192.168.1.168 (When 9070-IR is connected to PC directly) Default Login: Admin Default Password: 12345678 1.) After logging into the device active x controls will be required to be installed. If this screen does not appear make sure that active x has been allowed in internet explorer. 2.) Right click on yellow bar and install the activeX controls.
3.) Then click the install button and install the active X controls. 4.
Note: If no active x controls are showing up, please go to internet explorer and enable activeX controls.
The Control Console The IP Kamera 9070-IR Control Console starts in the navigate to the other options and settings of the 9070-IR Section of the webpage. In this section Live Video: The Live Video section allows the user to view the camera, change resolution views, Image: The Image section allows the user to adjust the image settings, including recording / viewing codec, frame rate, image tuning, brightness, contrast, saturation, and etc.
Live Video The Live video section of the IP Kamera 9070-IR is where the user can view the video of the device. From here resolution, record onto current pc, take a snapshot, zoom, and detect motion detection settings can be changed. Type and Zoom Type: The type function sets the streaming format for the IP Kamera 9070-IR. Select from the following type of resolutions depending on the format type set in the image settings.
To Zoom In: To Zoom into the picture move the mouse cursor over the picture and click and hold the left mouse. To Zoom Out: To Zoom out of the picture move the mouse cursor over the picture and click and hold the right mouse. Quick Zoom In: Quick zoom in is used to quickly zoom into the maximum zoom of the picture. To use this function on the picture double click the left mouse. Quick Zoom Out: Quick zoom out is used to quickly zoom into the maximum zoom of the picture.
Automatic Recording Inactivated Automatic Recording Activated Record Record: The record button on the 9070-IR when pressed will record the live video feed and save the video into the computer viewing. To record follow the following steps: 1.) Click on the record button 2.) Then select the designated folder to store the file. Then hit okay. 3.) Once the folder has been selected the device will start to record. To stop recording click on the red icon and it will return to the original state.
To use the snapshot function: 1.) Click on the snapshot button 2.) In explorer go to the selected path and the files will be created there. Image The image section changes the Image settings for the device and tunes the image of the IP Kamera 9070-IR Image Settings The Image settings section changes the video settings and the Name of the Kamera.
Resolution: Resolution (MPEG4+MPEG4+JPEG): M4:720P,M4:CIF,JPG:352 (MPEG4+JPEG): M4:VGA,JPEG:VGA (MPEG4+JPEG): M4:720,JPEG:352 (MEG4+MPEG4): M4:720,M4:CIF (Single MPEG4): M4:720 Color System: Select the broadcasting color system that pertains the country. NTSC/60Hz PAL/50Hz Rate Control: Select the most suitable Bit Rate Control.
From here control the live view Zoom Function and direction. Also once EPTZ is enabled, in the Live View Screen buttons will appear on the bottom with the pan, tilt, and zoom button Note: PTZ is only available in the mode below. When PTZ is enabled, it will automatically jump into that mode. Tune Image The tune image settings section controls and tunes the picture quality of the image. Keep in mind, the quality of the picture will also be affected by the quality of the lens that is being used.
Binning / Skipping mode: Binning enables low light-light performance. Select Binning, Skipping, 4x Binning mode (default is Binning). During BLC (Backlight control): Here Backlight control can be turned on or turned off. Backlight: Backlight controls how the 9070 will react by turning the picture darker or lighter depending on the amount of back light that is available. Brightness: Brightness controls the brightness of the picture.
FTP The FTP allows the user to easily save files onto a FTP server. With the 9070-IR, Video Files & Picture files (Jpeg) can both easily be saved onto the FTP server. Make sure the following information is filled out correctly FTP Server: Enter the FTP server address here User Name: Enter the FTP Username Password: Enter the FTP Password File Upload Path: Enter the upload path of the FTP Server SMTP (Outgoing E-mail Server) Enter the SMTP E-mail server information here.
Account Name: Enter then login of the mail account Password: Enter the password of the E-mail account Use SSL Connect: If the email server requires SSL (Secure Sockets Layer) this option need Sender Email: Enter the Sender Email Address SMTP Server: Enter the SMTP Outgoing mail address Email Address: Enter the Receiving Email address SNTP The SNTP is a protocol for synchronizing the clocks of computer systems over packet-switched, variablelatency data networks please setup the correct SNTP server informati
System The system section set ups the IP 9070-IR system configurations. This includes the following. Date and Time Set the date and Time of the device here. The Local Time: The local time corresponds to the current time of the IP Kamera 9070-IR. Time Setup: Setup the current time of the device here 1.) Set Manually: Set the time manually 2.) Synchronize with Computer Time: Synchronize the time with the current computers time 3.
The time stamp adds a time to the live video. When a recording is made this time stamp will show up with in the video file as well. To enable the Time Stamp check the enable box. User The user setting creates and removes users for access to the IP Kamera 9070-IR. Authority: Select one of the following options: Admin: Admin can operate all functions in Web interface. As well as, add or delete any user’s account. Operator: Operator can operate all functions in Web interface except user Add/Delete.
Light Enable Infrared: To disable the Infrared select on and hit submit Disable Infrared: To disable the Infrared select off and hit submit Device Tune Up The device tune up resets the 9070 to make sure that the device is running smoothly. This resets the internal memory of the device by restarting the 9070.
The language setting section is where you can select the language that you would like to use to use the 9070. Currently there are 3 languages available: English, Chinese (Traditional), Chinese (Simplified) there will be more to come. The 9070 will automatically detect the favored language of choice depending the settings used in Windows.
Update The Update Firmware section is where information on the 9070 is displayed. The Kernel Version, Uboot Version, Firmware Version, and other technical information on the device is displayed here. Updating the Device To update the device go to the update section. Here you will find the Current Version description. To update the device: 1.) Browse for the correct update file. 2.) Hit the update button. 3.) A message will appear, reminding you not to disconnect when updating. 4.
the device. You will need reconfigure the IP Kamera 9070, including Email, FTP, IP Address, Gateway, and etc. 6.) Enter update page, then hit the restart button. 7.) Then make sure you re-setup the device.
Setting Snapshot Path Select the snapshot path to the destination where snapshots will be saved. Video File Select the Video File format that the device will record in. 1.) Avi Duration: From the drop-down list, select the length of an AVI file. 2.) Avi Format: MPEG4 (720) MPEG4 (CIF) 3.) Hit the submit button to confirm new settings. FTP In the FTP section, select the file format that will be used for FTP transfer. Note: 1.) Before using the FTP function, set the FTP server information.
SD Card File Format: Select the video format to save into the SD card Split Filename Type: Select the format to save the files in the SD card. Select from: Name by Index: Creates file names according to index. Name by Time: Creates file names according to time. Split File Size: Select the size of each file that will be saved into the SD. Select from the following: None, 10mb, 25mb, 50mb, & 100mb.
Select the file format for IP Kamera 9070-IR to send in. Select from MPEG4 or MJPEG. EZ-Blog Note: To use the Ez Blog functionality, please make sure that your device has been port forwarded so that it can be accessed through the internet. EZ Blog allows you to easily integrate code into your blog which will let you directly stream into your blog, website, and any compatible site. This way you can IP Kamera as more than a regular security camera but also a promotional tool.
2.) Then select the size and dimensions that you would like the video to be displayed on the blog. 3.) Click on the create code button. 4.) You can highlight the embed code from inside the box and then copying (ctrl + C) or you can just hit the copy button to copy the code. 5.) Place that code somewhere in the body of your blog platform or website to display the video on the blog.
View in Full Screen To view the IP Kamera in full screen model you will need to press the Full Screen mode.
The My-Web functionality will make your IP Kamera more than just a surveillance tool. Now you can use it to promote your company, restaurant, business, school, and etc. With some basic website skills or tools any can make a My Web site. Turning On My Web Enable my web button: The enable My Web button will activate the My Web functionality. Once enabled every time the device is accessed it will be set to the My Web Page.
Using My Web To use the My Web feature: 1.) Use IPEdit and directly log into the IP camera. 2.) The device will open the root page of the 9070 to the My Web page. 3.) If you would like to return to the normal administrator page for the 9070 you can login to the admin site. For Example: 9070 IP Address: 192.168.12.111 Port:8080 Then on the web browser type in the following http://192.168.12.111:8080/index.
Alarm Motion Detection To enable motion detection: 1.) Select Enable in the motion detection option. 2.) Select the desired sensitivity of choice a. Pick from Lowest, Low, Medium, High, Highest b. The threshold can be selected from (1-99) 3.) Once the settings are set, on the window screen click on the picture where motion will be detected. Double click on the selected areas to remove the choice. Right click on the window screen for more options 4.
Enable Alarm Enable Alarm – Lost Ethernet Connection: Save into SD Card: When Ethernet connection is lost the device will automatically save into the SD card. FTP Enable Alarm - Upload When motion is detected, the IP Kamera 9070-IR will upload the video file to the selected FTP server. Enable Alarm - Save Into SD Card When motion is detected, the IP Kamera 9070-IR will upload the video file to the SD card.
Note: When using the mouse to zoom in the snapshot function will not take a picture of the zoomed picture but the resolution size. How to Enable and Use EPTZ Controller Note: When EPTZ is activated Video Codec mode will be switched to MPEG4 & M-Jpeg when disabled the codec will be set on Mpeg1, Mpeg2, & M-Jpeg. Also snapshot function works only with the EPTZ controller and not when using the mouse to EPTZ. 1.) Click on the EPTZ button located on the bottom of the screen of the 9070-IR. 2.
7.) Controlling the Device CGI HTTP Commands Http commands are command lines that execute commands to the device from a web browser, software, or code. The basic commands are provided below. There are two ways to input http commands with authorization required Password in http: http://login:password@ipaddress:port/command Password not in http: http://ipaddress:port/command Note: If using password not in http: command the browser asks for the login and password.
Ex. http command http://192.168.1.192/vb.htm?subnetmask=255.255.0.0 Note: Default subnet mask is 255.255.0.0 Change Gateway: This command changes the gateway the IP Kamera 9070-IR. http://ipaddress:port/vb.htm?gateway=gatewayaddress Ex. http command http://192.168.1.192/vb.htm?gateway=192.168.1.1 Change DNS: This command changes the gateway the IP Kamera 9070-IR. http://ipaddress:port/vb.htm?dnsip=dnsipaddress Ex. http command http://192.168.1.192/vb.htm?dnsip=168.95.1.
6.) Check the Cache value. For low latency, it should be 70~80 based on PC’s performance. Note: If the video is not smooth, set the caching value from 150~1200. This problem could be due to too much congestion, busy pc, and etc. 7.) Save the new settings 8.) Then go back to the VLC media player and go to Media > Advance Open File 9.) Next select the network tab and under the protocol select RTSP. 10.
Hit the play button and wait a few seconds for the program to start streaming. 9.) Using CNT with Surf16 CH CNT makes connecting to the IP Kamera 9070-IR a very simple task. Surf 16 CH a multi-device DVR monitoring software easily allows the user view the 9070-IR. Follow these simple steps: Finding the MAC Address There are two ways to find the MAC address in IPEdit. *Note: IP Server must be enabled on the device’s webpage. By default IP Server is enabled.
1.) In IPEdit, highlight the device that is being used. On the right side of IPEdit the MAC Address for CNT will be listed. *Note: Make sure when typing in the MAC address to leave out the “:” Find MAC Address in WAN Using IPService on IPEdit 1.) Find the MAC Address through the internet, Open IPEdit and hit the connect button on IP Service. 2.) Then Type in the name of the device, in this case it is “Sample Name”, then hit the search button. 3.
10.) Frequently Asked Questions (F.A.Q) Q1: Why can’t I view the video files that I have recorded, nothing is playing? Ans: VLC Codec, download VLC Codec from their website at: http://www.videolan.org/ Q2: How do I reset the device to manufacturers default values? Ans: On the back of the device there is a reset button, hold down the reset button for more than 7 seconds. Then give the 9070-IR a 1 minute to restart. Once the device has restarted it will be set back to manufacturer default settings.