IP Kamera 9070 User Manual Release Date: 10/05/2009 Manual Version: 1.
Warning: Any changes made to this equipment without permission may cause damages to the device! IMPORTANT NOTICE 1. IP Kamera 9070 was designed for indoor use, it is the responsibility of the user for any possible damages caused by outdoor use, especially in the rain. 2. Please use the power adapter provided by the dealer, the manufacturer responsibility for the possible damage from using power adapters not . 3. Do not shake the IP Kamera 9070 in any fashion 4.
Table of Content 1.) WELCOME........................................................................................................................... 5 INTRODUCTION ............................................................................................................................ 5 MINIMUM SYSTEM REQUIREMENTS ................................................................................................. 5 2.) PRODUCT OVERVIEW .....................................................................
TUNE IMAGE ..................................................................................................................................... 26 NETWORK ................................................................................................................................ 27 NETWORK ......................................................................................................................................... 27 FTP .......................................................................
1.) Welcome Introduction The IP Kamera 9070 provides reliable, high quality solution to IP Kameras. Its distinctive 720P HD quality picture, Tri-mode video capability, RTSP broadcasting capability, wide angle lens, built in 2GB microSD memory, and much more functions makes this small device very powerful and unique. Also with innovative features like My Web and EZ blog technology the 9070 can take your IP Kamera and make it a wonderful promotional tool, blogging camera.
Software • • • VLC media player 0.8.6b or above. Windows XP Service Pack 2 or above. Resolution of screen setting: 1280x960 or higher for the display of 720P 2.) Product Overview Features 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25.
Package Contents 1.) 9070 Unit x 1 2.) 9070 Installation CD 3.) AC Adaptor (One AC adaptor will be included and will correspond to the countries power standards) Specs: Input: 100-250Vac /47-63Hz, 1A Output: 5Vdc/1A 4.) Camera Mounting Bracket 5.
3.) Interface Description Rear Panel View Rear View Device Reset: Reset to Manufacturer Default: Hold Reset button for 5-10 Seconds and the device will reset to manufacturer default Video Out: The Video out requires a RCA connector to output video to a different source.
4.) Hardware Setup *Before setup the device make sure of the following: 1.) Make sure that all the package contents are all included if anything is missing please contact the store or your distributor. 2.) Make sure the power adaptor is the correct specification. 3.) Make sure that all the cables are working correctly Internet Accessible Setup The internet connection can be setup in two main ways so that the 9070 can be accessed through the internet a.
In this case, the 9070 is being connected to the internet through a hub, which is different from a router. The hub does not provide DHCP, and therefore would require that this setup have a static IP Address that is provided by the ISP. Contact the ISP to find out the static IP address so that your device can be accessed through the internet. Once a Static IP has been assigned the device will be able to automatically go onto the internet. . Connecting the Device 1.
2.) Select the IP Kamera section and pick the IP Kamera and Model that you are using. 3.) Download the following software and save them to the appropriate locations. a. IPEdit - Device search tool which allows you to modify IP settings, find your on the local network and IP Service. b. Surf 16 CH – 16 Channel DVR, Monitoring, & Recording Software. Views up to 16 channels on one screen. 4.) Once installation is complete please double click the IPEdit to configure and search for your device.
Installing VLC Codec The files that are recorded by the 9070 requires this codec so that you are able to view the view. Download the latest version of the VLC codec and install it into your computer. You can find the latest version of the codec from here http://www.videolan.org/ Using IP Edit IPEdit is a search tool designed to setup and access the IP Kamera 9070. IP Service is an additional feature which searches for the device easily without having to remember long complicated IP addresses.
Setup the Device: All devices will need to be on the same network if not the device cannot be accessed and will not be detected. Quick Easy Setup (Recommended) 1.) Click on the REF button, and wait a few seconds. IPEdit will automatically detect the network settings and setup the device. 2.) Once settings have been detected hit the apply button to apply the new settings. 3.) Hit yes to confirm and Enter the login and password for the Device to Approve changes 4.
Custom Setup (Advance Users) 1.) Highlight the device on the local devices section and on the right side of IPEdit all network information on the device will be displayed. If the device is not on the same network a Red Exclamation mark Network information section will appear in the IP 2.) To setup the device, you will need type in the correct Gateway and IP Address.
4.) Then hit the rescan button on IPEdit to confirm the changes have been made. IP Service How to use IP Service on IPEdit: IP service allows the user to directly connect to his / her device through the internet without having to remember long confusing IP Address. Instead you only need to remember the name of the device that the you have selected. Then the user can connect to IP Service, type in the device name, and connect directly to the device.
4.) Double click on your device and an Internet Explorer window will appear connecting directly to your device. Note: It is crucial to have the IP Address of the device port forwarded from the router that you are using so you can connect to your device from anywhere. Please refer to your routers user manual on how to port forward your device.
6.) Web Interface Connecting to the 9070 Once the 9070 has been setup correctly and access your IP Kamera 9070. An Internet Explorer browser screen pop up with the login screen. Default IP: 192.168.1.168 (When 9070 is connected to PC directly) Default Login: Admin Default Password: 12345678 1.) After you have logged into the device you will be required to install active x controls. If this screen does not appear make sure you allow active x. 2.) Right click on yellow bar and install the activeX controls.
3.) Then click the install button and install the active controls. 4.) Once activeX controls have been installed the video feed will show on the screen Note: If there is no active x controls that are showing up, please go to internet explorer and enable activeX controls.
The Control Console The IP Kamera 9070 Control Console starts in the navigate to the other options and settings of the 9070 Section of the webpage.
Live Video: The Live Video section allows the user to view the camera, change resolution views, Image: The Image section allows you to edit the image settings, including recording / viewing codec, frame rate, image tuning, brightness, contrast, saturation, and etc. Network: The network section allows you to change the devices network settings, ftp settings, smtp (email) settings, sntp settings, and IP service settings.
1X zoom: The 1X zoom is the normal view for each type. 2X zoom: This 2X zoom is 2 times the normal view for that type. Scaled 720: Is a resolution only available in MPEG-4-1, which sets the picture at 720P. Screen Size: Will enlarge the image to the who size of the screen. This function is very useful when trying to display on larger monitors. Mouse EPTZ Mouse EPTZ On the live video screen move the mouse cursor to the video and click left or right click to use the Mouse ETPZ functionality.
To Zoom Out: To Zoom out of the picture move the mouse cursor over the picture and click and hold the right mouse. Quick Zoom In: Quick zoom in is used to quickly zoom into the maximum zoom of the picture. To use this function on the picture double click the left mouse. Quick Zoom Out: Quick zoom out is used to quickly zoom into the maximum zoom of the picture. To use this function on the picture double click the right mouse.
3.) Once the folder has been selected the device will start to record. To stop recording click on the red icon and it will return to the original state. Note: Remember the VLC codec is required to play the video files that are recorded Snapshot Snapshot: The snapshot function, creates a easy way take pictures of the current view in the IP Kamera 9070. To setup the snapshot destination folder: 1.) Click on the Application link on the bottom menu 2.) Then select Snapshot path 3.
1.) Click on the snapshot button 2.) In explorer go to the selected path and the files will be created there. Image The image section allows you to change the Image settings for the device and tune the image of the IP Kamera 9070 Image Settings The Image settings section allows you to change the video settings and the Name of the Kamera.
Color System: Select the broadcasting color system that pertains to your country. NTSC/60Hz PAL/50Hz Rate Control: Select the Bit Rate Control that fits your needs. CVBR: Constrained Variable Bit Rate CBR: Constant Bit Rate M-JPEG Settings: The available Quality settings and FPS for the M-JPEG settings are shown below M-JPEG Quality Settings High Medium Low M-JPEG Frame Rate Settings 30 FPS 15 FPS MPEG4-1 Bit Rate: Select a value from 64~8000. FPS: Select a FPS from 30fps, 15fps, or 7.5fps 7.
Tune Image The tune image settings section allows you to control and tune the picture quality of the image. Keep in mind, the quality of the picture will also be affected by the quality of the lens that is being used. White Balance: Select from the following options auto, indoor, or outdoor Day and Night: Select the mode Day or Night TV Output: Select the mode enable or disable to output to a T.V Binning / Skipping mode: Binning enables low light-light performance.
Network Network The network section allows you to setup the network information for the IP Kamera 9070. IP Address: Actual IP Address of the device can be found here LAN IP Address: Local Area Network Address.
SMTP (Outgoing E-mail Server) Enter the SMTP E-mail server information here. My Server Requires Authentication: Check this section if your email requires Server Authentication.
Europe — europe.pool.ntp.org Asia — asia.pool.ntp.org Oceania — oceania.pool.ntp.org North America — north-america.pool.ntp.org South America — south-america.pool.ntp.org Africa — africa.pool.ntp.org Time Zone: Enter the corresponding time zone Automatically adjust for daylight saving time: Check this section if you want daylight saving time to be implemented automatically. IP Service With IP Service, the user will not have to remember long IP Address numbers.
Set the date and Time of the device here. The Local Time: The local time corresponds to the current time of the IP Kamera 9070. Time Setup: Setup the current time of the device here 1.) Set Manually: Set the time manually 2.) Synchronize with Computer Time: Synchronize the time with the current computers time 3.) Synchronize with SNTP: Synchronize with SNTP Time Stamp The time stamp adds a time to the live video. When a recording is made this time stamp will show up with in the video file as well.
The user setting allows you to create and remove users for access to the IP Kamera 9070. Authority: Select one of the following options: Admin: Admin can operate all functions in Web interface. Also, add or delete any user’s account. Operator: Operators can operate all functions in Web interface except user Add/Delete. Viewer: Viewer can only monitor the Web interface, but cannot operate all function and set parameters.
Language The language setting section is where you can select the language that you would like to use to use the 9070. Currently there are 3 languages available: English, Chinese (Traditional), Chinese (Simplified) there will be more to come. The 9070 will automatically detect the favored language of choice depending the settings used in Windows.
The Update Firmware section is where information on the 9070 is displayed. The Kernel Version, Uboot Version, Firmware Version, and other technical information on the device is displayed here. Updating the Device To update the device go to the update section. Here you will find the Current Version description. To update the device: 1.) Browse for the correct update file. 2.) Hit the update button. 3.) A message will appear, reminding you not to disconnect when updating. 4.
Warning: Before you go to the next step make sure you have all your setting information written down. The device will reset back to manufacturers default values after you restart the device. You will need reconfigure the IP Kamera 9070, including Email, FTP, IP Address, Gateway, and etc. 6.) Enter update page, then hit the restart button. 7.) Then make sure you re-setup the device.
Application Setting Snapshot Path The Snapshot path is the location where the snapshot pictures will be saved onto your computer. The default snapshot path will be set to C:\. To select the snapshot path click on the button and select the folder where the snapshots will be saved. Video File Select the Video File format that the device will record in. This setting will affect the FTP and the SMTP(Email) video formats. 1.
From the drop-down list, select the length of an AVI file. 2.) Avi Format: MPEG4(720) MPEG4(CIF) 3.) Hit the submit button to confirm new settings. FTP Note: 1.) Before you use the FTP function, you will need to set the FTP server information. You can click on the link to take you to the FTP setup section. 2.) If the SD Card is inserted into the device, the 9070 will only be able to record in M-Jpeg mode to the FTP.
Name by Index: Creates file names according to index. Name by Time: Creates file names according to time. Split File Size: Select the size of each file that will be saved into the SD. You can select from: None, 10mb, 25mb, 50mb, & 100mb. Enable Auto Overwrite: Auto Overwrite allows the device to automatically replace the oldest file on the SD card when it is full.
User List: This shows the Users Available to create an Ez Blog link with. Use a guest user account of the 9070 to create the EZ-Blog. You can easily create more users on the 9070 by clicking on the User link menu. Setup the Embed Code The Embed Code will be input into your html coding of your blog, website, etc. 1.) Type in the correct user and password for your 9070 account. (We highly recommend using a guest account) 2.
Media Player The media player allows you to view your recordings on the SD card directly through the internet without requiring downloading the file first. This feature makes it very convenient for live streaming. View in Full Screen To view the IP Kamera in full screen model you will need to press the Full Screen mode.
The My-Web functionality will make your IP Kamera more than just a surveillance tool. Now you can use it to promote your company, restaurant, business, school, and etc. With some basic website skills or tools any can make a My Web site.
The enable My Web button will activate the My Web functionality. Once enabled every time the device is accessed it will be set to the My Web Page. Login Required: The login required will require your My Web users to login to the device before being able to use it. This is a way to keep unwanted viewers from entering the My Web Setting up My Web To setup My Web you can download the MyWeb file from the 9070. 1.) Click on the Download Default Page. 2.) Save the Zip file to a location where you can edit it 3.
http://192.168.12.111:8080/index.htm Schedule Record Schedule The schedule allows you to select days and times that you would like to schedule automatic recording. You can pick a day from (Sunday – Saturday) and also a option for Everyday. To schedule automatic recording: 1.) Select the day that you would want to start recording. 2.) Select the From time and the To time. 3.) Once the schedule has been created hit the submit button to apply the new settings.
To enable motion detection: 1.) Select Enable in the motion detection option. 2.) Select the sensitivity of your choice a. You can pick from Lowest, Low, Medium, High, Highest b. You can also customize your own threshold from (1-99) 3.) Once you have set your settings on the window screen click on the picture where you want the motion to be detected. Double click on the selected areas to remove the choice. You can right click on the window screen for more options 4.
Enable Alarm – Lost Ethernet Connection: Save into SD Card: When Ethernet connection is lost the device will automatically save into the SD card. Saving a backup. Enable Alarm - Upload FTP When motion is detected, the IP Kamera 9070 will upload the video file to the selected FTP server. Enable Alarm - Save Into SD Card When motion is detected, the IP Kamera 9070 will upload the video file to the SD card.
How to Enable and Use EPTZ Controller Note: When EPTZ is activated Video Codec mode will be switched to MPEG4 & M-Jpeg when disabled the codec will be set on Mpeg1, Mpeg2, & M-Jpeg. Also snapshot function works only with the EPTZ controller and not when using the mouse to EPTZ. 1.) Click on the EPTZ button located on the bottom of the screen of the 9070. 2.) If the EPTZ has not been enabled you will be notified that it must be enabled. 3.) Select Enable on the EPTZ function then hit the submit button .
Change Name: This command allows you to change the name of the IP Kamera 9070 http://ipaddress:port/vb.htm?cameratitle=name Ex. http command: http://192.168.1.192/vb.htm?cameratitle=test_907011 Change IP Address: This command allows you to change the IP Address of the IP Kamera 9070 http://ipaddress:port/vb.htm?internetip=ipaddress Ex. http command: http://192.168.1.192/vb.htm?internetip=192.168.1.191 Change Port: This command allows you to change the Port of the IP Kamera 9070 http://ipaddress:port/vb.
MJPEG Streaming This command allows you to integrate streaming data into a software, website, or any other application. http://ipaddress:port/ipcam/mjpeg.cgi Ex. http command http://192.168.1.192/ipcam/mjpeg.cgi 8.) Using RTSP with VLC Before Setting up VLC: Make sure that the 9070 is set to be the DMZ host on the router that you are using, please refer to the routers manual on how to accomplish this. How to setup VLC media player & Open a network stream 1.) 2.) 3.) 4.
7.) Check the Cache value. For low latency, it should be 70~80 based on PC’s performance. Note: If the video is not smooth, set the caching value from 150~1200. This problem could be due to too much congestion, busy pc, and etc. 8.) Save the new settings 9.) Then go back to the VLC media player and go to Media > Advance Open File 10.) Next select the network tab and under the protocol select RTSP. 11.
- 49Ref#90020326K0709
9.) Using CNT with Surf16 CH CNT makes connecting to the IP Kamera 9070 a very simple task. Using Surf 16 CH and multi device DVR monitoring software, you can easily view your 9070CS. Follow these simple steps: Finding the MAC Address There are two ways to find the MAC address in IPEdit. *Note: IP Server must be enabled on your device’s webpage. By default IP Server is enabled. Find MAC Address in LAN Using IPEdit 1.) In IPEdit, highlight the device that you are using.
3.) Do not forget to enter the password and login. 10.) Frequently Asked Questions (F.A.Q) Q1: Why can’t I view the video files that I have recorded, nothing is playing? Ans: VLC Codec, you can download VLC Codec from their website at: Q2: How do I reset the device to manufacturers default values Ans: On the back of the device there is a reset button, hold down the reset button for more than 7 seconds. Then give the 9070 a 1 minute to restart.
