IP Kamera 9070-IRW User Manual Release Date: 8/2/2011 Firmware Version : V1.2.1.
Warning: Any changes made to this equipment without permission may cause damages to the device! IMPORTANT NOTICE 1. IP Kamera 9070-IRW was designed for outdoor/ indoor. 2. Please use the power adapter provided by the dealer, the manufacturer is not responsibility for the possible damage from using power adapters. 4. Do not shake the IP Kamera 9070-IRW in any fashion 5. Please contact the dealer If IP Kamera 9070-IRW is not working properly. Copyright © 2011 All rights reserved.
Table of Content 1.) WELCOME ........................................................................................................................................... 5 INTRODUCTION .............................................................................................................................................. 5 MINIMUM SYSTEM REQUIREMENTS ................................................................................................................... 6 2.) PRODUCT OVERVIEW ................
Network .............................................................................................................................................. 32 Wireless Settings ................................................................................................................................. 33 FTP ...................................................................................................................................................... 33 SMTP (Outgoing E-mail Server) ...................
1.) Welcome Introduction The IP Kamera 9070-IRW provides reliable, high quality solution to IP Kameras. Its distinctive 802.11N , 720P HD quality picture, Tri-mode video capability, built in SD memory storage, RTSP broadcasting capability, internal microphone and many more functions makes this small device very powerful and unique. The built in web server of the IP Kamera 9070-IRW will allow the IP Kamera to be viewed from any remote locations around the world while bringing ease of mind.
Minimum System Requirements CPU Minimum Requirements • • • • • • • • • Intel(R), Pentium(R), DUAL Core (D),CPU 3.0GHz or equivalent Operating Systems: WINDOWS Operating Systems (IE5.0+SPI) 512 MB system memory or above Video Card: 3D hardware accelerator card required – 100% DirectX 9.0c compatible 10/100 Ethernet switch/hub Sound Card: DirectX 9.
Package Contents 9070IRW Unit x 1 with sun cover 9070IRW Installation CD AC Adaptor x 1 Camera Mounting Bracket x 1 Antenna x 1 3.) Hardware Description Cable Description Cables: DC 12 V Power Input: Plugs in the Power Adapter to the DC 12V Card RJ45 Ethernet: Plug in the RJ45 Ethernet cable to the Ethernet Reset Button: Reset to Manufacturer Default: Hold Reset button for 5-10 Seconds and the device will reset to manufacturer default.
4.) Setting up the device Hardware setup Setting up the device Before setting up the device make sure of the following: 1.) Make sure that all the package contents are all included if anything is missing please contact the store or your distributor. 2.) Make sure the power adaptor is the correct specification. 3.) Make sure that all the cables are working correctly Connecting the Device 1.) Connect the IP Kamera 9070 to a HUB or Router with a RJ45 network cable. 2.
3.) Download the following software and save them to the appropriate locations. a. IP Edit - Device search tool which allows you to modify IP settings, find your on the local network and IP Service. b. Surf 16 CH – 16 Channel DVR, Monitoring, & Recording Software. Views up to 16 channels on one screen. c. Surf Pop – Surf Pop is a new interactive IP Kamera monitoring software 4.) Once installation is complete please double click the IP Edit to configure and search for your device.
3.) Simply double click on your device in the local device section and a internet explorer window will appear, and start connecting to your device. All devices will need to be on the same network if not the device cannot be accessed and will not be detected. Custom Setup (Manual Setup) Note: If no DHCP is found on the device, the 9070IRW will be given a static IP Address. Default IP: 192.168.1.168 (When 9070IRW is connected to PC directly) Default Login: admin Default Password: 12345678 1.
IP Address: Make sure the first 3 sections of the IP Address matches the gateway address. Example: Gateway Address – 192.168.1.1 IP Address – 192.168.1.xxx 3.) Once the Default Gateway information has been obtained, enter the correct information into IP Edit then press the submit button. 4.) Then hit the rescan button on IP Edit to confirm the changes have been made. Setting up Wireless Settings Step by Step: 1.) After log in web page, please go to the network Wireless.
3.) Click on the for more information on how to setup the device. 4.
5.) Type in the passphrase for the router and hit the apply button. 6.) 7.) Wait about 60 seconds for device to connect. 8.) Then check to see for the connection successful under the connection status and the device is good to go. 9.) Unplug the RJ45 cable of the device and search on IPEdit for the new wireless settings. You will see a (W) next to your device in IPEdit which means wireless is activated. If the RJ45 cable is not disconnect you will see two IP Address on the device.
Advance Setup: Click on the On Link under advance section Click on the Site Survey Link then select the wireless internet network that you would like to connect to and hit the add profile button to add a new profile A new window pop and you will be required to enter the necessary network information including the passphrase or password for the wireless internet.
Then hit apply to save all settings and wait about 60 seconds for device to connect. Then go back to the Main Wireless page and click on the on link under Advance for more options. Select the Profile link to see the profiles that you have added to the device.
Click on your newly added profile and hit the activate button to start up the Wireless settings. Then click on Link Status to make sure that your device is connected to the wireless network. Note: If the device is connected it will show some information in the Link Status page. Now the device is connected to the wireless network. Unplug the Ethernet cable to the device. Then unplug the power cable to the device for about 15 seconds.
IP Service Using IP Service How to use IP Service on IP Edit: IP service allows the user to directly connect to his / her device through the internet without having to remember long confusing IP Address. Instead you only need to remember the name of the device that the you have selected. Then the user can connect to IP Service, type in the device name, and connect directly to the device.
2.) IP Service through Google cloud Note: Make sure that the enable IP Service feature is turned on under the network settings of your device. Searching with IP Service: To use IP Service: 1.) Click on the image and you will be taken to the IP Service webpage. 2.) Depending on which server you selected in the IP Service settings, you will need to select from server 1 or server 2. 3.) Type in the name that you have selected for your device and hit the submit button.
Searching with IP Service (Google Cloud): To use IP Service (Cloud): 1.) Click on the image and you will be taken to the IP Service webpage. 2.) Type in the name that you have selected for your device and hit the submit button. Note: You can name your device in the network settings of your device under IP Service. 3.) Simply put your mouse over the picture of your device and if you have selected your location it will show on the map in the left. Then click on the Icon to connect to your device.
5.) Internet Access (Port Forwarding) The internet connection can be setup in two main ways so that the 9070IRW can be accessed through the internet Router / Firewall Setup Using a Router/Firewall to connect each device to the internet Note: The device needs to be port forwarded on the router so that it can be accessed by the internet. For example 9070IRW IP Address: 192.168.1.882 9070IRW Port: 9070 On the router that is being used port forwarded (port triggered) IP Address 192.168.1.882 and port 9070.
Static IP Setup Static IP Address provided by the ISP In this case, the 9070IRW is being connected to the internet through a hub, which is different from a router. The hub does not provide DHCP, and therefore would require that this setup have a static IP Address that is provided by the ISP. Contact the ISP to find out the static IP address so that your device can be accessed through the internet. Once a Static IP has been assigned the device will be able to automatically go onto the internet. 6.
1.) Once you have logged into the device you will be required to install active x controls. 2.) Right click on yellow bar and install the activeX controls. 3.) Then click the install button and install the active controls. 4.) Once active X controls have been installed the video feed will show on the screen Note: If there is no active X controls that are showing up, please go to internet explorer and enable active X controls.
1.) Under internet options in IE select the security tab. 2.) Then click on the custom level button 3.
The Control Console The IP Kamera 9070-IRW Control Console starts in the navigate to the other options and settings of the 9070-IRW Section of the webpage. In this section Live Video: The Live Video section allows the user to view the camera, change resolution views, Image: The Image section allows you to edit the image settings, including recording / viewing codec, frame rate, image tuning, brightness, contrast, saturation, and etc.
Application: The application section allows you to change the video recording format, ftp storage settings, SD Card settings, Media Player: The Media player can directly access the files in the built in memory. Each video file & picture can be accessed here and streamed through the internet. Logout: After using the 9070, the user can click on the Logout feature to ensure that no one else can see the IP Kamera without a login or password. Please do not forget to log out after each use.
Motion Detection Motion Detection: The motion detection icon will display when motion has been detected. This setting must be activated in the application section Motion Inactive - When motion detection is inactive Motion Activated - When motion detection is activated, the icon will turn blue Active Record Active Record: Active record will show up when the device is actively recording. Active recording functions like motion detection, scheduler, or an alarm will set off this automatic recording.
To use the snapshot function: 1.) Click on the snapshot button, and you will see the screen flicker black. 2.) In explorer go to the selected path and the files will be created there. Record Record: The record button on the 9070IRW when pressed will record the live video feed and save the video into the computer viewing. To record follow the following steps: 1.) Select the recording path that you would like to store the file under in the snapshot path. under 2.
3.) Once the folder has been selected the device will start to record. To stop recording click on the red icon and it will return to the original state. Note: Remember you need VLC codec to play the video files that are recorded Mouse EPTZ Mouse EPTZ On the live video screen move the mouse cursor to the video and click left or right click to use the Mouse ETPZ functionality. Here you can easily Zoom in, Zoom Out, Quick Zoom, Quick Zoom Out.
Image The image section allows you to change the Image settings for the device and tune the image of the IP Kamera 9070-IRW Image Settings The Image settings section allows you to change the video settings and the Name of the Kamera. Camera Name: Select a camera name for the device and then hit submit Video Codec: In this section you can select the codec formats that you want allowed on your live mode and available for other functionality.
Resolution: In this section you can select the resolution type that you need to be able to display or use. Simply select the resolution that best fits your needs Resolution (MPEG4+MPEG4+JPEG): M4:720P,M4:CIF,JPG:352 (MPEG4+M-JPEG): M4:VGA,JPEG:VGA M4:720P, JPG:720 (MPEG4-1+MPEG4-2) M4:720,M4:CIF Not supported in Firefox: (Single MPEG4): M4:720 (Single MJPEG): M4:720 Color System: Select the broadcasting color system that pertains to your country.
Cable / ADSL: Most high speed internet users today use Cable / ADSL as the main internet provider line. Fiber Optics: High speed fiber optics provides the best solution for outside the network because it is very fast. Intranet (LAN): When using the IP Kamera from within the network this is the best option. Custom: This setting allows you to manually input a setting for the Bit Rate, FPS, and picture quality.
Day and Night: Select the mode Day or Night TV Output: Select the mode enable or disable to output to a T.V Binning / Skipping mode: Binning enables low light-light performance.
Wireless Settings The wireless settings section will allow you to setup the wireless feature of the 9070-IRW. Please refer to Setting up wireless settings page 11 FTP The FTP section of the IP Kamera 9070-IRW allows you to save video clips FTP Server: The FTP server address is where the IP Address of the FTP server will be entered.
Use SSL Connect: If the email server requires SSL (Secure Sockets Layer) this option need Sender Email: Enter the Sender Email Address SMTP Server: Enter the SMTP Outgoing mail address Email Address: Enter the Receiving Email address Submit: After all settings have been made. Hit the submit button to save all changes. Send Test E-Mail: This button will send a test e-mail to the designated account. This way, you can check to make sure that the settings are correct.
IP Service IP service is a added service that provides you a platform so you do not remember a long IP Address. Just enter the name of your device into IP Service and you can find your device. Note: Port forwarding will be required on your router to connect to the device In this section you can to turn off/on this service as well as select which server you would like your device on. . Note: IP Service is set to ON by default. To close this feature, uncheck the enable button.
Camera Title: This is the name of the device. Country: The country where the device is located. City: The city where the device is located. MAC: Physical address or MAC of the device. GAE Start: Will setup the device load information to the Google cloud so that your device can be accessed on the cloud. See the section on www.myipedit.com for more information. CNT Sharing of Account and Password: Cross Network Technology allows for your device to be reached without having to port forward.
RTSP Real Time Streaming Protocol (RTSP) gives the device another way to stream live video. Using programs that support RTSP, you can broadcast the videos from the 9070-IRW live. Note: To access the device from outside the network. Please make sure of the following: 9070-IRW should be set to DMZ host, or mapping router's TCP ports 554 and 8554 to 9070-IRW, preferably at the same time mapping UDP port 6970-9999 System The system section allows you to setup the IP 9070-IRW’s system configurations.
Date and Time Set the date and Time of the device here. The Local Time: The local time corresponds to the current time of the IP Kamera 9070-IRW. Time Setup: Setup the current time of the device here 1.) Set Manually: Set the time manually 2.) Synchronize with Computer Time: Synchronize the time with the current computers time 3.) Synchronize with SNTP: Synchronize with SNTP Time Stamp & OSD The time stamp adds a time to the live video.
User In this section, you can create different user access rights for different types of users. Authority: Select one of the following options: Admin: You can operate all functions in Web interface. Also, you can add or delete any user’s account. Operator: You can operate all functions in Web interface except user Add/Delete. Viewer: You can only monitor the Web interface, but cannot operate all function and set parameters.
The beeper function allows the device to make beeping sounds when network connection is lost or unavailable. In this section you can adjust the beeper interval which will set the number of seconds between each beep. Press the beeper test to test the beeper. Device Tune Up The device tune up resets the 9070-IRW to make sure that the device is running smoothly. This resets the internal memory of the device by restarting the 9070-IRW.
Update The Update Firmware section is where information on the 9070-IRW is displayed. The Kernel Version, Uboot Version, Firmware Version, and other technical information on the device is displayed here. Updating the Device To update the device go to the update section. Here you will find the Current Version description. To update the device: 1.) Browse for the correct update file. 2.) Hit the update button. 3.) A message will appear, reminding you not to disconnect when updating.
4.) Please wait for the loading circle to finish, and wait for an update confirmation page. 5.) Once the device is updated you will see a update confirmation and click okay. Warning: Before you go to the next step make sure you have all your setting information written down. The device will reset back to manufacturers default values after you restart the device. You will need reconfigure the IP Kamera 9070-IRW, including Email, FTP, IP Address, Gateway, and etc. 6.
Event Log In the Events Log section you can find the log for the IP Camera. This section will notify you any events that have taken place with the IP Kamera.
Setting Snapshot Path The snapshot path section allows you to configure where you would like your live snapshot and recording files are stored on your local computer. Simply, click on the folder to where you want to save the files. button and choose a PC Split File Size: Allows you to select the segment size of the files that will be recorded onto your computer. File Settings The file settings page allows you to configure certain settings for files that are sent to E-mail, FTP, or SD card.
File Configuration: Under this section you can select a prefix name for your recorded files. Here you can also add a date stamp to your files by checking the box that says Add Date Stamp File Format Settings: In this section you can select the file that type that you would like to record in. Depending on the resolution and video codec selected you can choose from various format types. Select the Video File format that the device will record in. 1.) Avi Format:MPEG4 (720) & MPEG4 (CIF) 2.
SD Card The SD card section is where settings to setup the SD card recording is located. In this section you can configure Enable Auto Overwrite: Auto Overwrite allows the device to automatically replace the oldest file on the SD card when it is full. Split Filename Type: Allows you to sort the file into two different methods. section is selected the 9070-IRW will sort the Name by Time: If add date stamp in the device by time.
SD Format: SD format will format the entire SD card Unmount: The unless remounted. feature will unmount the SD card from the device, so it cannot be accessed Reset: To mount the SD card back onto the device, you can use the button Net Drive The net drive function allows you to save your recordings to a local network computer. This provides a extra storage place for pictures and videos from motion detection and schedule recording.
4.) Here you can select a user in your windows OS that you would like to share with or Everyone which will share this drive with everyone on your network. Select everyone and hit the add button. Note: The user selected must have Read / Write capabilities for this function to work correctly. 5.) Then hit the share button on the bottom and you should receive a confirmation to show that the folder has been shared.
6.) Click the done button and it will take you back to the folders properties. Under the sharing tab you will find a section that says network path. Copy that information and put it into the 9070-IRW webpage in the net drive section. Setting up Net Drive After the computer has been setup. Now you will need to setup the net drive in the 9070-IRW 1.) For the login and password since we have selected everyone as the sharing user, simply type in any login or password.
3.) Now select the split size to select how big you want the files to be. Then hit the submit button and the net drive will start to work. E-mail SMTP The SMTP application settings is where the file format uploaded by email can be selected. From here you can choose the files to be in either Jpeg (picture) format or Mpeg. Note: To use the device in Mpeg format make sure to unmount the SD card of the device first.
EZ-Blog EZ Blog is a an easy way to integrate your IP camera with your blog or website. Simply by using the code produced you can have live video from your IP camera on your blog and websites. Start by selecting which method you would like to use EZ blog. There are two ways that you can use EZ blog. 1.) Using OCX to broadcast EZ blog Advantages of using OCX: Instant Response Disadvantages: Router needs to be setup in order to use this method.
User List: The user list shows the available users you can use to setup EZ Blog. We highly recommend to use guest accounts and if a guest account is needed you can easily do so by accessing the menu. Once the user is selected, now you can easily create the embed code: 1.) Type in the password for the selected user. 2.) Select the dimensions you would like the image to be 3.) Select the create code button to create the embed code 4.) Press the copy button to copy the code that you would like to use.
Advantages of using CNT: Does not require router setup to use. Can cross network, simply plug and play. Disadvantage: Requires constant communication to make sure device is connected. Note: To use CNT feature, the GAE server must be turned on. You can do this by going to the network tab, and click on the IP Service link To use CNT to integrate your IP camera with your blog: 1.) After you have enabled the GAE feature, click on the copy button of EZ Blog by pressing the copy button. 2.
4.) On the bottom where you can preview the image you will see that it will show a login screen. 5.) Then hit the copy button and paste the code that you have copied into your blog or website. My Web The My-Web functionality will make your IP Kamera more than just a surveillance tool. Now you can use it to promote your company, restaurant, business, school, and etc. With some basic website skills or tools any can make a My Web site.
Enable my web button: The enable My Web button will activate the My Web functionality. Once enabled every time the device is accessed it will be set to the My Web Page. Login Required: The login required will require your My Web users to login to the device before being able to use it. This is a way to keep unwanted viewers from entering the My Web How to use my WEB 1. Download sample. 2. Save the zip file to the location . Press browse, and select the zip file you download. 3. 4.
Using My Web To use the My Web feature: 1.) Use IP Edit and directly log into the IP camera. 2.) The device will open the root page of the 9070-IRW to the My Web page. 3.) If you would like to return to the normal administrator page for the 9070-IRW you can login to the admin site. For Example: 9070-IRW IP Address: 192.168.12.111 Port:8080 Then on the web browser type in the following http://192.168.12.111:8080/index.
Schedule Record Schedule The schedule allows you to select days and times that you would like to schedule automatic recording. You can pick a day from (Sunday – Saturday) and also a option for Everyday. To schedule automatic recording: 1.) Select the day that you would want to start recording. 2.) Select the From time and the To time. 3.) Once the schedule has been created hit the submit button to apply the new settings.
Schedule Recording Schedule Record allows you to select where the schedule will record the video files to. Schedule Record – Upload Via FTP: Saves schedule recordings into FTP Schedule Record – Save into SD Card: Saves schedule recordings into SD Card Schedule Record – Upload via E-mail SMTP: schedule recordings into e-mail Alarm Motion Detection To enable motion detection: 1.) Select Enable in the motion detection option.
2.) The Mode: Can be set for indoors or outdoors. Indoors will have a more sensitive motion detection setting while outdoor will be less sensitive. 3.) Select the sensitivity of your choice a. You can pick from Lowest, Low, Medium, High, Highest b. You can also customize your own threshold from (1-99) 4.) Once you have set your settings on the window screen click on the picture where you want the motion to be detected. Double click on the selected areas to remove the choice. 5.
Enable Alarm – Lost Ethernet Connection: Save into SD Card: When Ethernet connection is lost the device will automatically save into the SD card. Saving a backup. FTP Enable Alarm - Upload When motion is detected, the IP Kamera 9070-IRW will upload files to the selected FTP server. SD Card Enable Alarm - Save Into When motion is detected, the IP Kamera 9070-IRW will upload files to the SD card.
The media player allows you to view your recordings on the SD card directly through the internet without requiring downloading the file first. This feature makes it very convenient for live streaming. View in Full Screen To view the IP Kamera in full screen model you will need to press the Full Screen mode. Logout When you are done use the IP Kamera 9070IRW the logout function allows you to easily logout of your device.
7.) Controlling the Device CGI HTTP Commands Http commands allow you to control the device with commands. The basic commands are provided below. There are two ways to input http commands with authorization required Password in http: http://login:password@ipaddress:port/command Password not in http: http://ipaddress:port/command Note: If you use the password not in http: command you will need to enter it when the browser asks for the password.
http://ipaddress:port/vb.htm?subnetmask=subnetmask Ex. http command http://192.168.1.192/vb.htm?subnetmask=255.255.0.0 Note: Default subnet mask is 255.255.0.0 Change Gateway: This command allows you to change the gateway the IP Kamera 9070-IRW. http://ipaddress:port/vb.htm?gateway=gatewayaddress Ex. http command http://192.168.1.192/vb.htm?gateway=192.168.1.1 Change DNS: This command allows you to change the gateway the IP Kamera 9070-IRW. http://ipaddress:port/vb.htm?dnsip=dnsipaddress Ex.
3.) On the bottom of the screen click the Reset preference button. 4.) On the bottom left hand side of VLC select the all under the show settings area. 5.) Then in the left panel select Input / Codecs > Demuxers > RTP/RTSPl and type in the RTSP user name and RTSP password. 6.) Check the Cache value. For low latency, it should be 70~80 based on PC’s performance. Note: If the video is not smooth, set the caching value from 150~1200. This problem could be due to too much congestion, busy pc, and etc. 7.
10.) Type in the RTSP address of your device For Mpeg4 Stream1 : rtsp:///mpeg4 For Mpeg4 Stream2 : rtsp://:8554/mpeg4 Example: rtsp://122.116.137.123/mpeg4 11.) Hit the play button and wait a few seconds for the program to start streaming.
9.) Using CNT with Surf16 CH CNT makes connecting to the IP Kamera 9070-IRW a very simple task. Using Surf 16 CH and multi device DVR monitoring software, you can easily view your 9070-IRW. Follow these simple steps: MAC Address There are two ways to find the MAC address in IP Edit . *Note: IP Server must be enabled on your device’s webpage. By default IP Server is enabled. Find MAC Address in LAN Using IP Edit 1.) In IP Edit , highlight the device that you are using.
3.) Do not forget to enter the password and login. 10.) Frequently Asked Questions (F.A.Q) For More updated FAQ please visit the FAQ section of website at: http://sites.google.com/site/aviosysfaq/ Q1: Why can’t I view the video files that I have recorded, nothing is playing? Ans: VLC Codec, you can download VLC Codec from their website at: Q2: How do I reset the device to manufacturers default values Ans: On the back of the device there is a reset button, hold down the reset button for more than 7 seconds.
11.) Customer Feedback Your Feedback is definitely important for us to continue providing the great quality products and service that Aviosys has to offer. We definitely would like to know what you think about our products and how we can we can make your Aviosys experience even better. Please email us at our service department at Service@Aviosys.com or visit customer feedback form at: http://spreadsheets.google.com/viewform?hl=en&formkey=dGowalg3UndrdTJHNUIxdlljQXI3Q2c6MA..
