IP Kamera 9070-IRW User Manual Release Date: 2010/7/22 Manual Version: V1.00 Firmware Version : V1.2.1.
Warning: Any changes made to this equipment without permission may cause damages to the device! IMPORTANT NOTICE 1. IP Kamera 9070-IRW was designed for outdoor/ indoor. 2. Please use the power adapter provided by the dealer, the manufacturer is not responsibility for the possible damage from using power adapters. 4. Do not shake the IP Kamera 9070-IRW in any fashion 5. Please contact the dealer If IP Kamera 9070-IRW is not working properly. Copyright © 2010 All rights reserved.
Table of Content 1.) WELCOME ........................................................................................................................................... 5 INTRODUCTION .............................................................................................................................................. 5 MINIMUM SYSTEM REQUIREMENTS ................................................................................................................... 6 2.) PRODUCT OVERVIEW ................
SNTP .................................................................................................................................................... 36 IP Service ............................................................................................................................................. 37 RTSP .................................................................................................................................................... 38 SYSTEM ...................................
1.) Welcome Introduction The IP Kamera 9070-IRW provides reliable, high quality solution to IP Kameras. Its distinctive 802.11N , 720P HD quality picture, Tri-mode video capability, built in SD memory storage, RTSP broadcasting capability, internal microphone and many more functions makes this small device very powerful and unique. The built in web server of the IP Kamera 9070-IRW will allow the IP Kamera to be viewed from any remote locations around the world while bringing ease of mind.
Minimum System Requirements CPU Minimum Requirements Intel(R), Pentium(R), DUAL Core (D),CPU 3.0GHz or equivalent Operating Systems: WINDOWS Operating Systems (IE5.0+SPI) 512 MB system memory or above Video Card: 3D hardware accelerator card required – 100% DirectX 9.0c compatible 10/100 Ethernet switch/hub Sound Card: DirectX 9.
Package Contents 1.) 9070-IRW Unit x 1 with Lid 3.) 9070-IRW Installation CD 4.) AC Adaptor (AC adaptor will be included and will correspond to the countries power standards) Specs: Input: 100-250Vac /47-63Hz, 1A Output: 12Vdc/1A Max: 12W 5.) Camera Mounting Bracket 6.
3.) Interface Description Rear View & Cable Description Rear View: Cable and Antenna hole for Wireless Cables: DC 12 V Power Input: Plugs in the Power Adapter to the DC 12V Card RJ45 Ethernet: Plug in the RJ45 Ethernet cable to the Ethernet Reset Button: Reset to Manufacturer Default: Hold Reset button for 5-10 Seconds and the device will reset to manufacturer default. Video Out: The Video out requires a BNC connector to output video to a different source.
4.) Hardware Setup *Before setup the device make sure of the following: 1.) Make sure that all the package contents are all included if anything is missing please contact the store or your distributor. 2.) Make sure the power adaptor is the correct specification. 3.
Static IP Setup Static IP Address provided by the ISP. In this case, the 9070-IRW is being connected to the internet through a hub, which is different from a router. The hub does not provide DHCP, and therefore would require that this setup have a static IP Address that is provided by the ISP. Contact the ISP to find out the static IP address so that your device can be accessed through the internet. Once a Static IP has been assigned the device will be able to automatically go onto the internet.
5.) Software Setup The software for the device is located on the Media Link-IP Family CD that came with the device. IP Kamera Pack is located on the main page of the CD. Please follow the directions carefully and install the necessary files Software 1.) First place the Media Link-IP Family CD that came with your device into your CD/DVD Rom drive. The CD should auto run but if it does not go to the CD/DVD Rom drive and select the file ―autorun.html‖. 2.
3.) Download the following software and save them to the appropriate locations. a. IP Edit - Device search tool which allows you to modify IP settings, find your on the local network and IP Service. b. Surf 16 CH – 16 Channel DVR, Monitoring, & Recording Software. Views up to 16 channels on one screen. c. Surf Pop – Surf Pop is a new interactive IP Kamera monitoring software 4.) Once installation is complete please double click the IP Edit to configure and search for your device.
IP Edit IP Edit is a search tool designed to setup and access the IP Kamera 9070 IRW. IP Service is an additional feature which searches for the device easily without having to remember long complicated IP addresses. Instead, this technology allows the user find his or her device through the internet just by device name. Note: Please allow the IP Kamera 9070 IRW 1 to load before using IPEdit. Default IP: 192.168.1.
Setup the Device: All devices will need to be on the same network if not the device cannot be accessed and will not be detected. Quick Easy Setup (Recommend for Beginner Users) 1.) Click on the REF button, and wait a few seconds. IP Edit will automatically detect the network settings and setup the device. 2.) Once settings have been detected hit the apply button to apply the new settings. 3.) Hit yes to confirm and Enter the login and password for the Device to Approve changes 4.
Custom Setup (Advance Users) 1.) Highlight the device on the local devices section and on the right side of IP Edit all network information on the device will be displayed. If the device is not on the same network a Red Exclamation mark Network information section will appear in the IP 2.) To setup the device, you will need type in the correct Gateway and IP Address.
3.) Once the Default Gateway information has been obtained, enter the correct information into IP Edit and hit the submit button. 4.) Then hit the rescan button on IP Edit to confirm the changes have been made.
Setting up Wireless Settings Step by Step: 1.) After log in web page, please go to the network settings on the bottom and select Wireless. A new window should pop up with the wireless settings . 2.) Select the Step by Step option on the wireless screen. 3.) Click on the for more information on how to setup the device. 4.
5.) Type in the passphrase for the router and hit the apply button. 6.) Wait about 60 seconds for device to connect. 7.) Then check to see for the connection successful under the connection status and the device is good to go.
8.) Unplug the RJ45 cable of the device and search on IPEdit for the new wireless settings. You will see a (W) next to your device in IPEdit which means wireless is activated. If the RJ45 cable is not disconnect you will see two IP Address on the device.
Then hit apply to save all settings and wait about 60 seconds for device to connect. Then go back to the Main Wireless page and click on the on link under Advance for more options. Select the Profile link to see the profiles that you have added to the device.
Click on your newly added profile and hit the activate button to start up the Wireless settings. Then click on Link Status to make sure that your device is connected to the wireless network. Note: If the device is connected it will show some information in the Link Status page.
Now the device is connected to the wireless network. Unplug the Ethernet cable to the device. Then unplug the power cable to the device for about 15 seconds. Then plug in the power to the device and give the device about 1 minute to start up. Then with IP Edit search for the new wireless device. If the device is using wireless, you should see a (w) next to the name of your device.
4.) Double click on your device and an Internet Explorer window will appear connecting directly to your device. Note: It is crucial to have the IP Address of the device port forwarded from the router that you are using so you can connect to your device from anywhere. Please refer to your routers user manual on how to port forward your device.
6.) Web Interface Connecting to the 9070-IRW Once the 9070-IRW has been setup correctly, connect to the login page. An Internet Explorer browser screen pop up with the login screen. Default IP: 192.168.1.168 (When 9070-IRW is connected to PC directly) Default Login: Admin Default Password: 12345678 1.) Once you have logged into the device you will be required to install active x controls. 2.) Right click on yellow bar and install the activeX controls. 3.
Note: If there is no active X controls that are showing up, please go to internet explorer and enable active X controls.
Web Console The IP Kamera 9070-IRW Control Console starts in the navigate to the other options and settings of the 9070-IRW Section of the webpage. In this section Live Video: The Live Video section allows the user to view the camera, change resolution views, Image: The Image section allows you to edit the image settings, including recording / viewing codec, frame rate, image tuning, brightness, contrast, saturation, and etc.
Live Video The Live video section of the IP Kamera 9070-IRW is where the user can view the video of the device. From here resolution, record onto current pc, take a snapshot, zoom, and detect motion detection settings can be changed. Type and Zoom Type: The type function allows you to set the streaming format for the IP Kamera 9070. You can select from the following type of resolutions depending on the format type you have set in the image settings.
Motion Detection Motion Detection: The motion detection icon will display when motion has been detected. This setting must be activated in the application section When no motion is detected the motion detection icons will look like the following. No Motion Detected But, in the case that motion is detected and recording has started, the icon will look will light up blue.
Record Record: The record button on the 9070-IRW when pressed will record the live video feed and save the video into the computer viewing. To record follow the following steps: 1.) Select the recording path that you would like to store the file under in the applications tab in snapshot path. 2.) Click on the record button 3.) Once the folder has been selected the device will start to record. To stop recording click on the red icon and it will return to the original state.
To use the snapshot function: 1.) Click on the snapshot button, and you will see the screen flicker black. 2.) In explorer go to the selected path and the files will be created there. Image The image section allows you to change the Image settings for the device and tune the image of the IP Kamera 9070-IRW Image Settings The Image settings section allows you to change the video settings and the Name of the Kamera.
Resolution: In the resolution section you can select from the following options. Resolution (MPEG4+MPEG4+JPEG): M4:720P,M4:CIF,JPG:352 (MPEG4+M-JPEG): M4:VGA,JPEG:VGA M4:720P, JPG:720 (MPEG4-1+MPEG4-2) M4:720,M4:CIF Not supported in Firefox: (Single MPEG4): M4:720 (Single MJPEG): M4:720 Color System: Select the broadcasting color system that pertains to your country.
Fiber Optics: High speed fiber optics provides the best solution for outside the network because it is very fast. Intranet (LAN): When using the IP Kamera from within the network this is the best option. Custom: This setting allows you to manually input a setting for the Bit Rate, FPS, and picture quality.
TV Output: Select the mode enable or disable to output to a T.V Binning / Skipping mode: Binning enables low light-light performance.
Default Gateway: The default gateway address is the address to connect to the router. DNS Server: Domain Name System Address Http Port: Enter the port that you would like the 9070 to connect on.
Wireless Settings The wireless settings section will allow you to setup the wireless feature of the 9070-IRW. Please refer to page 18 or Setting up wireless section for more details. FTP The FTP section of the IP Kamera 9070 allows you to save video clips FTP Server: The FTP server address is where the IP Address of the FTP server will be entered.
My Server Requires Authentication: Some servers require SMTP Authentication for security purposes. If your email server requires this option, make sure to have this section checked.
IP Service IP service is a added service that provides you a platform so you do not remember a long IP Address. Just enter the name of your device into IP Service and you can find your device. Note: Port forwarding will be required on your router to connect to the device In this section you can to turn off/on this service as well as select which server you would like your device on. . Note: IP Service is set to ON by default. To close this feature, uncheck the enable button.
City: The city where the device is located. MAC: Physical address or MAC of the device. Once you have setup IP Service you can connect to IP Service through software IP Edit Search tool or through www.myIP Edit .com Enable Share: Check this feature to enable video sharing on guest accounts only. Make sure that the guest account has already been created in the user section. Once this section has been made you can come here to verify that Note: This function is for IP Surf Pop software.
Date and Time Set the date and Time of the device here. The Local Time: The local time corresponds to the current time of the IP Kamera 9070. Time Setup: Setup the current time of the device here 1.) Set Manually: Set the time manually 2.) Synchronize with Computer Time: Synchronize the time with the current computers time 3.) Synchronize with SNTP: Synchronize with SNTP Time Stamp The time stamp adds a time to the live video.
User In this section, you can create different user access rights for different types of users. Authority: Select one of the following options: Admin: You can operate all functions in Web interface. Also, you can add or delete any user’s account. Operator: You can operate all functions in Web interface except user Add/Delete. Viewer: You can only monitor the Web interface, but cannot operate all function and set parameters.
Device Tune Up The device tune up resets the 9070 to make sure that the device is running smoothly. This resets the internal memory of the device by restarting the 9070. You can set the Device tune up to reset each hour, day Month, or Week Language Settings The language setting section is where you can select the language that you would like to use to use the 9070. Currently there are 3 languages available: English, Chinese (Traditional), Chinese (Simplified).
Update The Update Firmware section is where information on the 9070 is displayed. The Kernel Version, Uboot Version, Firmware Version, and other technical information on the device is displayed here. Updating the Device To update the device go to the update section. Here you will find the Current Version description. To update the device: 1.) Browse for the correct update file. 2.) Hit the update button. 3.) A message will appear, reminding you not to disconnect when updating.
4.) Please wait for the loading circle to finish, and wait for an update confirmation page. 5.) Once the device is updated you will see a update confirmation and click okay. Warning: Before you go to the next step make sure you have all your setting information written down. The device will reset back to manufacturers default values after you restart the device. You will need reconfigure the IP Kamera 9070, including Email, FTP, IP Address, Gateway, and etc. 6.) Unplug the device then plug it back in. 7.
Application The Application Section allows you to setup the Video File information, FTP, Memory Management, SMTP Settings Snapshot Path The Snapshot path is the location where the snapshot pictures will be saved onto your computer. The default snapshot path will be set to C:\. To select the snapshot path click on the button and select the folder where the snapshots will be saved.
Recording Format Select the Video File format that the device will record in. 1.) Avi Format: MPEG4 (720) & MPEG4 (CIF) 2.) Avi Duration: From the drop-down list, select the length of an AVI file, then press submit FTP The FTP section allows you to view your current FTP settings. From here you may have to un-mount the SD memory so that you can record in MPEG4 format.
Note: 1.) Before you use the FTP function, you will need to set the FTP server information. You can click on the link to take you to the FTP setup section. 2.) If the SD Card is inserted into the device, the 9070 will only be able to record in M-Jpeg mode to the FTP. SD Card File Format: Select the video format that you would like to save into the SD card Split Filename Type: Select the format that you would like to save the files in the SD card.
E-mail SMTP In the settings section, you can find the SMTP information by clicking on the SMTP tab. Here you can see the current SMTP Server information and email address. Storage Settings You can also select the file format in which you would like the IP Kamera 9070-IRW to send. Select from MPEG4 or MJPEG.
EZ-Blog Note: To use the Ez Blog functionality, please make sure that your device has been port forwarded so that it can be accessed through the internet. EZ Blog allows you to easily integrate code into your blog which will let you directly stream into your blog, website, and any compatible site. This way you can IP Kamera as more than a regular security camera but also a promotional tool. Note: Any blog platform that supports javascript can utilize the Ez blog functionality (i.e Blogspot).
Media Player The media player allows you to view your recordings on the SD card directly through the internet without requiring downloading the file first. This feature makes it very convenient for live streaming. View in Full Screen To view the IP Kamera in full screen model you will need to press the Full Screen mode.
My Web The My-Web functionality will make your IP Kamera more than just a surveillance tool. Now you can use it to promote your company, restaurant, business, school, and etc. With some basic website skills or tools any can make a My Web site. Turning On My Web Enable my web button: The enable My Web button will activate the My Web functionality. Once enabled every time the device is accessed it will be set to the My Web Page.
How to use my WEB 1. Download sample. 2. Save the zip file to the location . 3. Press browse, and select the zip file you download. 4. Press upload and send the zip file to 9070 web. 5. Confirm setting . *** If familiar with webpage langrage, you can change the webpage in zip file to your own webpage. *** Setting up My Web To setup My Web you can download the My Web file from the 9070. 1.) Click on the Download Default Page. 2.) Save the Zip file to a location where you can edit it 3.
9070 IP Address: 192.168.12.111 Port:8080 Then on the web browser type in the following http://192.168.12.111:8080/index.htm RSS Use can get 9070-IRW message by RSS as Snapshot, Motion detection , Record as motion ***Notice: User need to register in DDNS *** In the Dyndns section, type in the Dyndns that you register from www.dyndns.com and add a /rss20.
The schedule allows you to select days and times that you would like to schedule automatic recording. You can pick a day from (Sunday – Saturday) and also a option for Everyday. To schedule automatic recording: 1.) Select the day that you would want to start recording. 2.) Select the From time and the To time. 3.) Once the schedule has been created hit the submit button to apply the new settings. Schedule Recording Schedule Record allows you to select where the schedule will record the video files to.
Alarm Enable Alarm Enable Alarm – Lost Ethernet Connection: Save into SD Card: When Ethernet connection is lost the device will automatically save into the SD card. Saving a backup. Enable Alarm - Upload FTP When motion is detected, the IP Kamera 9070 will upload the video file to the selected FTP server. Enable Alarm - Save Into SD Card When motion is detected, the IP Kamera 9070 will upload the video file to the SD card.
Motion Detection To enable motion detection: 1.) Select Enable in the motion detection option. 2.) Select the sensitivity of your choice a. You can pick from Lowest, Low, Medium, High, Highest b. You can also customize your own threshold from (1-99) 3.) Once you have set your settings on the window screen click on the picture where you want the motion to be detected. Double click on the selected areas to remove the choice. 4.) You can right click on the window screen for more options 5.
Media Player The media player allows you to view your recordings on the SD card directly through the internet without requiring downloading the file first. This feature makes it very convenient for live streaming. View in Full Screen To view the IP Kamera in full screen model you will need to press the Full Screen mode. Logout When you are done use the IP Kamera 9070 CSWO/CSO the logout function allows you to easily logout of your device.
7.) Controlling the Device CGI HTTP Commands Http commands allow you to control the device with commands. The basic commands are provided below. There are two ways to input http commands with authorization required Password in http: http://login:password@ipaddress:port/command Password not in http: http://ipaddress:port/command Note: If you use the password not in http: command you will need to enter it when the browser asks for the password.
Change Name: This command allows you to change the name of the IP Kamera 9070-IRW http://ipaddress:port/vb.htm?cameratitle=name Ex. http command: http://192.168.1.192/vb.htm?cameratitle=test_907011 Change IP Address: This command allows you to change the IP Address of the IP Kamera 9070-IRW http://ipaddress:port/vb.htm?internetip=ipaddress Ex. http command: http://192.168.1.192/vb.htm?internetip=192.168.1.
MJPEG Streaming This command allows you to integrate streaming data into a software, website, or any other application. http://ipaddress:port/ipcam/mjpeg.cgi Ex. http command http://192.168.1.192/ipcam/mjpeg.cgi 8.) Using RTSP with VLC Before Setting up VLC: Make sure that the 9070-IRW is set to be the DMZ host on the router that you are using, please refer to the routers manual on how to accomplish this.
6.) Check the Cache value. For low latency, it should be 70~80 based on PC’s performance. Note: If the video is not smooth, set the caching value from 150~1200. This problem could be due to too much congestion, busy pc, and etc. 7.) Save the new settings 8.) Then go back to the VLC media player and go to Media > Advance Open File 9.) Next select the network tab and under the protocol select RTSP.
10.) Type in the RTSP address of your device For Mpeg4 Stream1 : rtsp:///mpeg4 For Mpeg4 Stream2 : rtsp://:8554/mpeg4 Example: rtsp://122.116.137.123/mpeg4 11.) Hit the play button and wait a few seconds for the program to start streaming.
9.) Using CNT with Surf16 CH CNT makes connecting to the IP Kamera 9070 a very simple task. Using Surf 16 CH and multi device DVR monitoring software, you can easily view your 9070-IRW. Follow these simple steps: MAC Address There are two ways to find the MAC address in IP Edit . *Note: IP Server must be enabled on your device’s webpage. By default IP Server is enabled. Find MAC Address in LAN Using IP Edit 1.) In IP Edit , highlight the device that you are using.
3.) Do not forget to enter the password and login. 10.) Frequently Asked Questions (F.A.Q) For More updated FAQ please visit the FAQ section of website at: http://sites.google.com/site/aviosysfaq/ Q1: Why can’t I view the video files that I have recorded, nothing is playing? Ans: VLC Codec, you can download VLC Codec from their website at: Q2: How do I reset the device to manufacturers default values Ans: On the back of the device there is a reset button, hold down the reset button for more than 7 seconds.
11.) Customer Feedback Your Feedback is definitely important for us to continue providing the great quality products and service that Aviosys has to offer. We definitely would like to know what you think about our products and how we can we can make your Aviosys experience even better. Please email us at our service department at Service@Aviosys.com or visit customer feedback form at: http://spreadsheets.google.com/viewform?hl=en&formkey=dGowalg3UndrdTJHNUIxdlljQXI3Q2c6MA..
