IP Kamera 9060A -SL User Guide IP Kamera 9060A-SL Manual version: 1.03 Date: 2008.
Caution: Any changes or modifications not approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for FCC and CE. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in commercial environment. Important Notice: 1.IP Kamera 9060A-SL is for indoor use.
Table of Contents 1. PRODUCT OVERVIEW ...............................................................................................4 FEATURES ........................................................................................................................ 2. PHYSICAL DESCRIPTION..........................................................................................5 BOX CONTENT ....................................................................................................................
1. Product Overview Use latest high sensitivity Sensor, 9060A Plus only need little light for clear video which can be use for lower light source like monitor the road at night .. IP Kamera 9060A-SL is an IP camera that has a embed web server. This camera can put up live image on-line and make immediately remote accessible through standard web browsers. By simply plugging 9060A-SL into Internet IP Kamera 9060A-SL, Users can observe from any where in the world. FEATURES 1.
2. Physical Description BOX CONTENT IP Kamera package content： 1 x IP Kamera 9060A-SL 1 x RJ 45 internet line 1 xTansformer,110~240. 1 x CD 1 x Quick Installation Guide System Requirement Intel Pentium3 and above or relevant AMD CPU Any system can use IE ( Internet Explore) like Windows 98 / SE / 2000 / ME / XP, 64MB memory or above.
3. Interface Description Front Panel : 1. Power indicator ( LED ) 2. Lens ( CMOS ) Rear Panel : 1. Reset Switch (Left: Normal Mode Right: Reset Mode) 2. DC Power: 5V, 1.0A 3. Microphone In 4. RJ 45 (Cat5 Network) Notice * Please use Microphone for Audio In * Reset ON/OFF: please turn to ON for 5-10 seconds and then turn back to OFF to Finish reset: OFF ON (Wait for 5 Second) OFF.
4. Installation Before installation: Before using IP Kamera 9000A-SL, check as follows. Confirm your package contents Prepare a computer connected to your LAN Electricity 110 ~ 240 V Hardware installation 1. Plug in RJ 45 line to connect 9060A-SL with HUB. 2. Connect the HUB into your modem. 3. Connect 9060A-SL power. 4. Turn your computer on: Software installation Please follow the steps below to install the software. 1. Insert the CD that came in the package and windows will auto-run.
3. Please follow the installation wizard and install all the recommended programs. 4. After installation is complete, a shortcut of “IPEDIT” & “INFINITY Cam” will be created on the Desktop and in program list of start of your computer NOTE: * For NEW function – TO Record in “WMV” format, install IP KamVid 1070. 5. Initialization 1. Add IP Service in IPEDIT Open “IPEdit.exe”. Make sure that the IP Kamera 9060A-SL is properly turned on and there is a Ethernet connection from the RJ45 cable.
(Figure 1.1 IPEDIT) A. Local Devices area: (Fig 1.
IPEDIT will search and display all IP Products 9XXX series under the same local Ethernet. The default name for the IP Power 9060A-MP is “Cam_location” Please refer to (Fig. 1.2 above). 1. Double click and highlight your IP Power 9060A-MP device. The default device name and IP/Network settings will all be displayed on the right hand side of IPedit.
b.) Then click Submit after the settings have been selected. Wait about 20 seconds for the new settings to be updated. c.) Click Rescan, and the new device settings will display in text window. Note: 1.) Make sure the RJ45 network cable is connected and the 9060A-MP is powered on. 2.) * The default IP address of the 9060A-MP is 192.168.0.100. If you cannot get into the webpage of the 9060A-MP, please make sure to set subnet of the IP Kamera 9060A-MP to match with your PC Subnet Mask.
* Same SUBNET: The first 3 sections of IP address is same - XXX.XXX.XXX.abc. The part of XXX must be the same. (E.g. IP address is 192.168.1.100, then another IP address 192.168.1.123 is the IP in same subnet.) 5 .The default username and password of IP Kamera 9060A-SL are: Username: admin Password: 12345678 NOTE: 1. DirectX will register automatically after IP Kamera 9060A-MP had been installed on your PC. This will allow the 9060 to be used as a local camera by any software that supports DirectX.
Internet Explorer 7 1.) Open Internet Explorer 2.) At the top of the screen, click on Tools and select Internet Options Figure 1.1 3.) Under the Browsing history section. Click on Delete. (Fig. 1.1) 4.) Under the tempoary internet section hit the delete button, then select yes (figure 1.2.) Figure 1.
5.) Under the Cookies section hit the delete button, then select yes (figure 1.
B. Internet online devices: By setting the server address in IP server of advanced setting page, you can easily to get the IP address of IR IP Kamera 9060A-MP on internet just by searching for the name of your device. The default IP address for the IP server is 220.135.169.136. The configurations for IP Server can be found under the advance setup tab. Step1: Click the green “connect” button Step2: Type the keyword in “Device name“ (Minimum of 3 characters) Step3: Press Search button.
Work with Yahoo /MSN Messenger To use your camera with Yahoo or MSN Messenger: 1. In this case we are using Yahoo Messenger. 2. Select the friend you would like to send your video. In the picture below, we have decided to share the camera with our friend Yahoo Helper. 2. Choose T1/E1 when system ask you about the Internet connecting speed. 3. Then My WEBCAM will pop up. Please go to “file “ “Preference” your prefer video parameter.
4. You can type in appointed IP address (No matter Real IP or Dynamic IP) and confirm by clicking “Add” and choose if reverse the out streaming video. We support: A. Normal B. Flip Vertical C. Flip Horizontal D. Rotate 180 And you can also adjust the color, Brightness, contrast, Hue, Saturation, Sharpness and ETC. Note 1 : For safety issues , when transfering video by Yahoo or MSN, only the Administrator is allowed to stream video. You have to type in the username and password.
6. WEBPAGE FUNCTIONS When you have configured your computers configured IP address, you can finish setting through IE browser. Click the picture in the window of IPEdit directly; you can open the web page of IP9060A-MP. Login setting General user: Default general ID is guest, Password is password. Administrator: Default administrator ID is admin, Password is 12345678. *Note: Login and Password each cannot exceed 15 Characters.
LiveView setting After a few minutes, you will see the video of the IR IP Kamera 9060A-MP. If your system asks you to download ActiveX please select YES and download Only the Administrator can access the settings in the configuration tab located on the top of the window. (Including settings like: Administration, Update, and etc) Image Setting Setting windows is located on the left hand side. It is used to set up image parameter. 1.
3. Anti-Flicker The Anti-Flicker can be adjusted to three different levels of your video streaming quality. Depending on the location of your camera you can pick from Indoor 50hz AC illumination Indoor 60hz illumination Outdoor Note: Please do select “outdoor“ to view a outdoor scene or during the daytime. If the IP Kamera, 9060A-SL gets too much light the picture will be too bright. 4. Audio In default mode the audio is normally closed, but this option allows the user to turn it on. 5.
Advanced setting Advanced menu will be displayed when you right click mouse on the image window. From here you can set up the image, record AVI, record WMV, zoom, motion detect, splits, rotate, set time, and set the directory of your pictures path. The functions can be set in other web page of IR IP Kamera 9060A-MP. 1. Image parameter setting Right click on the picture screen and select “image”.
2. Record image : Support AVI & WMV format 2-1 Record AVI file Right click on the motion image, choose “record AVI ” which will open the corresponding window. Here the user can adjust the settings parameter of AVI Frame Rate, file name and directory. Please do type in full file name, for instance “ C:\tmp\1230-10.avi “. The resolution setting decides the resolution of AVI file. . 2-2 Record WMV: Right click on the motion image, choose “record WMV” which will open corresponding windows.
If you select For local playback: The recorded file will be larger. You can select from two separate resolution sizes 320 x 240 or 640 x 480 For playback on most pocket PCs: The recorded file will by smaller. 3. Zoom Right click mouse on the motion image and choose “zoom”. Draw a frame around the selected image where you would like to zoom. Release the mouse button and the picture will zoom in to the area that you have selected. Right click on the mouse to go back to your original view.
4. Motion detection In this settings, you can enable Motion detection function. Motion detection can send a picture to a PC, send an email, or upload to a FTP site when motion is detected. The resolution of the pictures that is taken corresponds to the resolution that you have set on your screen. . The Motion detection settings allows the user to setup a trigger so that if movement is detected in a certain area of the view, the 9060A-MP will take a picture 1.
Network setting In this menu you can setup or change the method your IP Cam is connected. There are 3 different choices that you can use: A. STATIC: Works in both real and dynamic IP address. B. DHCP: The IP address is distributed by an DHCP Server. C. PPPOE: Directly connects through the connection provided by the ISP. A. To Setup a STATIC mode, please follow the following steps: The IP address of IP camera 9060A-SL should be located in the same subnet as your PC.
B. Set up DHCP mode, steps: 1. Click DHCP, and then click “Submit” 2. Click “Reboot”, its need to wait for 15-20 seconds to enable again. 3. Use Search Tools; click Update to find IP CAM. 4. When change finished, the IP Assignment of Search Tools will show DHCP.. C. Set up PPPOE mode (As use XDSL), steps: Before e setup PPPOE, please do setup “Mail server “ in Server page. Before use PPPOE to get real IP address from ISP please do follow connection: ”Submit” Click PPPOE. 1.
with the ISP to get an IP address. For this to work correctly you will have to setup the username & password in the web page first. It will take few second for IP Kamera to get real IP address from ISP. You can click update to check the status. D. HTTP Server: Appoint port number of HTTP, default is 80. HTTP port setting can help use more than one IP Kamera for customer had only one real IP. E. DNS Server: Appoint address of DNS Server IP, default is 168.95.1.1.
B. FTP (File Transfer Protocol) Steps: *Note: Login and Password each cannot exceed 15 characters. 1. Fill in Ftp Server (IP/ Host), Account ID, Password, and Ftp mode. 2. Click “Submit” to save setting. C. DDNS (Dynamic Domain Name Server) Steps: Before use DDNS service, please create your own account in Websitehttp://www.dyndns.org And apply host name for DDNS service. Register user’s name, password, and account and upload path. In Websitehttp://www.dyndns.org 1. Fill in Hostname (for instance: 1011.
Administration setting In this page the user can set 9060A-MP (Mega Pixels)’s Camera name, Administration’s account, general user’s account, and black list of IP address. By Setting the Name of your camera it makes it easier to distinguish your cameras especially when you have more than one. Camera Name: To change your Camera’s name type over the current default camera name and hit the submit button.
IP Black List: The IP Black List allows the user to block up to a maximum of 5 IP Address. Just enter the IP address you would like to block and hit add Event Trigger & Timer schedule setting Event trigger: In this page settings, the user can select to ENABLE one or two Motion Detect functions and the way to transfer detect pictures: Save in PC, Send by E-mail, Save in Ftp server. Click “Submit” after type account/password to relevant text windows.
Update setting By update functions, user can online update 9060 firmware to get more functions; 1. Press “browse” key to chose new ROM Code 2. Press ”Submit” key to upload, it will holding 7-10 secs (100M Ethernet ) 3. The windows will showing “wait system Reboot”, it means upload finished. 4. Update will last 50 SECS. During this process, make sure power supply stabilization. Power fail will damage the 9060. 5. The web page will auto update after finished. 6.
7. FAQ Q 1: I forgot the ID and password for the administrator account, so I cannot log into the administration Page. A: 1.) Please set the Reset switch to “Reset Mode: Right” 2.) Wait for 10 seconds. 3.) Turn the reset switch back to Normal Mode: Left *Please refer to the picture on page 6 if you have questions. Q 2: The Web Kamera does not launch? A: Upgrade Internet Explorer to 5.0 or higher and make sure the subnet is same as your PC’s. Please refer Initialization settings on page 8.
