D800-Dante D800 A-Net Distributor A-Net Distributor User Guide 9310 1030 0001F rev 1.1 © 2015 Aviom, Inc.
READ THIS FIRST Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
WARNING! TO REDUCE THE DANGER OF ELECTRICAL SHOCK DO NOT REMOVE COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY. To reduce the risk of fire or electrical shock, do not expose this product to rain or other types of moisture. To avoid the hazard of electrical shock, do not handle the power cord with wet hands. Replace fuse with same type and rating. Operating Temperature: 0˚C to 50˚C (32˚F to 122˚F) Risque de choc électrique – ne pas ouvrir.
Certifications EMC: EN55103-1:2009 EN 55103-2: 2009 EN 55022:2006 / CISPR 22:1997 CAN/CSA-CEI/IEC CISPR 22:02 FCC 47 CFR, Part 15 Safety: ANSI/UL 60065 Audio, Video and Similar Electronic Apparatus – Safety Requirements; Issued: 2003/06/30 Ed: 7 Rev: 2013/07/24 CSA C22.2 No.
Aviom, Inc. Limited Warranty Aviom, Inc. warrants this product against defects in materials and workmanship for a period of one year from the date of the original retail purchase. This warranty does not apply if the equipment has been damaged due to misuse, abuse, accident, or problems with electrical power.
Warranty Information Please record the following information for future reference: Your Authorized Aviom Dealer: Name: Address: Phone: Serial Numbers of Your Aviom Products: Date of Purchase: Your Authorized Aviom Dealer is your primary source for service and support. The information recorded above will be helpful in communicating with your Authorized Aviom Dealer should you need to contact Aviom Customer Service.
Table of Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . ii Certifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv Aviom, Inc. Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . v Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . .
Activity LED. . . . . . . . . . . . . . . . . . . . . . . . . . 22 Error LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Sync LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Dante Configuration DIP Switches . . . . . . . . . . . . . . . . . . . . DIP Switch Block 1 . . . . . . . . . . . .
D800 and D800-Dante Thank you for purchasing the Aviom D800 or D800-Dante A-Net Distributor. This User Guide is designed to familiarize you with your new product’s features and to have your personal mixing system up and running as quickly as possible. Two versions of the D800 are available: the standard D800 includes a Pro16e™ A-Net® input, compatible with all Pro16® Series and Pro16e-capable devices; the D800-Dante adds connectivity for a Dante™ digital audio network.
Conventions Used in this Document Using Personal Mixers When referring to the use of the Personal Mixers in a personal mixing system in general, the term Personal Mixer is used to describe a case where an A360 Personal Mixer, A-16II Personal Mixer, or an A-16R Rack-mount Personal Mixer (with or without the optional A-16CS Control Surface) can be used. Cat-5 Cables In most cases Cat-5e, Cat-6, and Cat-6e cables can be interchanged.
Package Contents The D800 (or D800-Dante) A-Net Distributor box includes: •• One A-Net Distributor •• Documentation Options for your personal mixing system include: •• Cat-5e/Cat-6 interconnect cables •• SB4 System Bridge •• D800, D800-Dante, A-16D, or A-16D Pro A-Net Distributors •• A360 Personal Mixers •• A320 Personal Mixers •• A-16II Personal Mixers •• AN-16/o v.
Compatibility The D800 A-Net Distributor is compatible with Pro16, Pro16e, and Pro64 A-Net devices as detailed below. Pro16 Products The A-Net Out from the following Pro16 devices may be connected to the D800 or D800-Dante’s rear panel A-Net In port: •• AN-16/i v.
About Category 5 The term Category 5 (also referred to as Cat-5) is broadly used to describe a type of high performance network cabling used for data transmission purposes to connect computer networks and other devices. A standard patch cable consists of four twisted pairs of copper wire terminated by RJ45 male connectors. The cable assembly is used to provide connectivity between any two Cat-5 female RJ45 jacks.
Pro16 A-Net Out Passive Coupler Passive Coupler Pro16 A-Net In Total Pro16 A-Net cable length: 500 feet (150 meters) Passive A-Net cable length: 400 feet (122 Passive Total Pro16e meters) Pro16 A-Net Out Pro16 A-Net In Coupler Coupler Cable Lengths Pro16e A-Net Out Passive Coupler Passive Coupler Pro16 or Pro16e A-Net In For Pro16 applications—connecting one Pro16 device to another—the Cat-5 cables used with your Aviom products may be up to 500 feet (approximately 150 meters) in length between dev
as you do not exceed the specified maximum cable length). If you need a longer cable on occasion, this is a simple solution. Note that the maximum cable length performance can be compromised by using inline couplers or other passive connection devices. AC Line Conditioning Aviom products are digital devices and as such are sensitive to sudden spikes and drops in the AC line voltage. Changes in the line voltage from lightning, power outages, etc., can sometimes damage electronic equipment.
D800 A-Net Distributor Aviom’s series of D800 A-Net® Distributors provides support for parallel connections of up to eight Pro16® devices, including the A360, A320 A-16II, and A-16R Personal Mixers. Overview Two versions of the D800 are available. The standard D800 includes a Pro16e™ A-Net input, compatible with all Pro16 Series and Pro16e-capable devices. This input port also supports an A-Net Bridge input, allowing up to four synchronous Pro16 A-Net streams to be connected.
D800 Front Panel Front panel features described in this section are found on both the standard and Dante versions of the D800 A-Net Distributor.
Function 5 Sync LED, green 6 Power LED, red 7 USB port 8 Load button D800 and D800-Dante A-Net Distributors User Guide 10
A-Net Ports 1 to 8 The eight A-Net ports on the front panel of the D800 A-Net Distributor provide a copy of the D800’s input signal to the connected A-Net devices. When connected to a personal mixer such as the A320, A-16II or A-16R data flows in only one direction; when connected to an A360 Personal Mixer data can be unidirectional or bidirectional. The switch below the Cat-5 jack controls the data flow.
Connecting Personal Mixers To connect a Personal Mixer to the D800: •• Connect a Cat-5e cable from an A-Net port on the D800 A-Net Distributor to the A-Net In port on the Personal Mixer. •• DC power is supplied automatically to the Personal Mixer—no external DC power supply is required. •• Connect additional Personal Mixers using Cat-5e cables from an available A-Net port on the D800 A-Net Distributor to the A-Net input on the Personal Mixer.
Mode Switches Each of the eight A-Net ports on the front of the D800 has a two-position mode switch labeled with Roman numerals I and II. The switches are used to control data flow, either unidirectional (I) or bidirectional (II).
The front panel Sync LED lights green on the standard version of the D800 A-Net Distributor when a valid A-Net stream is connected to the rear panel A-Net In port.
D800 Rear Panel The features on the left side of the rear panel are found on both the standard and Dante versions of the D800. Function 1 Fuse holder 2 Power On/Off switch 3 AC Power connection, IEC 4 Ethernet network connection, RJ45 5 Pro16e Mixes Out, locking RJ45 6 Pro16e A-Net Out, locking RJ45 7 Pro16e A-Net In or A-Net Bridge In, locking RJ45 P Note: The standard version of the D800 is not field upgradable to the Dante version.
Power Supply The rear of the D800 A-Net Distributor contains the standard IEC power input for the unit. The main power supply in the D800 is a switching type, compatible with the variety of electrical systems in use worldwide. The D800 can operate with input voltages from 100 to 240 volts and at rates from 50 to 60 Hz. Replaceable IEC cables for AC power systems throughout the world are available from many electronics dealers. Avoid using cable adapters whenever possible.
A Wi-Fi router connected to the Ethernet port on a D800 sends additional mix information from an A360 Personal Mixers that can be displayed on an iOS device. A-Net In Port / A-Net Bridge The standard D800 A-Net Distributor gets its network input from the A-Net In port on its rear panel. This A-Net signal can come from: •• a single Pro16 analog input module such as the AN-16/i-M Mic Input Module •• a single Pro16e analog input module such as the AN-16/i v.2 Input Module •• a maximum of four AN-16/i v.
P Note: The console card connected to the port labeled 1-16 on the System Bridge is assumed to be the clock source when using multiple cards. Multiple console cards connect to an SB4 System Bridge. The console card connected to the System Bridge’s 1-16 port is assumed to be providing the clock. A Pro64 digital audio network may also be connected to the D800 by using the Pro64 ASI A-Net Systems Interface and including the SB4 System Bridge to merge its outputs.
A-Net Out Port On the standard version of the D800, the A-Net Out port supplies a copy of the Pro16e A-Net stream (up to 64 slots) that is connected to the A-Net In port. On the D800-Dante version of the product, the A-Net Out also supplies an exact copy of the input source, but note that the source is selectable between the Dante stream connected to the Dante interface’s Dante Primary or Secondary port and the A-Net stream connected to the A-Net In port.
Mixes Out Port The D800 Mixes Out port is used with the Network Mix Back feature and the A360 Personal Mixer. Each A360 Personal Mixer connected to the D800 can send its stereo mix back into the network so that it may be connected to a Pro16 output device such as the AN-16/o v.4 Output Module.
D800-Dante Rear Panel The features described below are found only on the Dante version of the D800. Function 1 Dante configuration and Stereo Link DIP switches 2 Dante network Primary port, locking RJ45 3 Dante network activity LEDs, green 4 Dante 1GB network LEDs, red 5 Dante network Secondary port, locking RJ45 6 Dante network Error LED, red 7 Dante Sync LED, green P Note: The standard version of the D800 is not field upgradable to the Dante version.
Dante Network Ports The Dante interface on the D800-Dante A-Net Distributor has two gigabit network ports labeled Primary and Secondary. The Dante Secondary port can be configured to be a pass-through port or a redundant copy of the Primary port. Configuring Dante settings requires the Dante Controller software available from the Audinate website. The D800-Dante supports sample rates of 44.1kHz and 48kHz coming from the Dante network.
Dante Configuration DIP Switches Setting up a Dante network requires the use of the Dante Controller software available from the Audinate website. Once configured, the D800-Dante’s onboard set of four DIP switch blocks is used to configure the A-Net-specific settings. This document refers to the DIP switch blocks with numbers 1-4 as shown below. DIP switch blocks are referred to using numbers 1-4.
This example uses red handles to show Slots 5-6, 9-10, 11-12, and 15-16 with stereo links on.
DIP Switch Block 3 DIP Switch Down Up 1 Mono Stereo Link Slots 33-34 2 Mono Stereo Link Slots 35-36 3 Mono Stereo Link Slots 37-38 4 Mono Stereo Link Slots 39-40 5 Mono Stereo Link Slots 41-42 6 Mono Stereo Link Slots 43-44 7 Mono Stereo Link Slots 45-46 8 Mono Stereo Link Slots 47-48 9 ID1 Reserved Reserved 10 ID2 Reserved Reserved In DIP Switch block 3, switches 9 and 10 (ID1 and ID2) are reserved for future use. They should be left in the down position by default.
Dante Setup The D800-Dante requires some additional configuration using Audinate’s Dante Controller software when it is part of a Dante network. Routing Channels Any active audio resource in a Dante network may be routed to the D800-Dante. Routing channels requires the Dante Controller software, available from the Audinate website. It can be run on either Mac or PC computers. Complete documentation for the software is available from Audinate.
closed. Channel transmit/receive settings are stored within each Dante device until they are changed using the Dante Controller software. Device View Opening the Device View for any Dante device in the network will display a tabbed view of additional settings for the device. There is an overview of the device’s firmware, its transmit and receive settings, as well as settings for the sample rate and redundancy.
Device Config Tab The settings for Sample Rate and Device Latency are found within the Device Config tab. Choose a sample rate from the drop-down menu. To change the sample rate for the D800-Dante, select a new rate from the drop-down menu. Use the radio buttons in the Device Latency section to choose a latency value that best matches the network you have set up.
Network Config Tab The settings for the D800-Dante’s Primary and Secondary ports are found within the Network Config Tab of the Device View. Two settings are available in the drop-down menu. When set to Switched, both ports are identical; Dante devices can be daisy chained. When set to Redundant, the Secondary port will serve as a redundant copy of the data appearing at the Primary port. Note that using the Redundant setting requires that the network be configured using a pair of gigabit switches.
Personal Mixing Systems A personal mixing system can be configured with a variety of input sources including analog, digital console cards, and Dante network devices and consoles. Up to eight Personal Mixers (A360, A320, A-16II or A-16R) can be connected and powered per D800. This section shows some typical personal mixing system configurations.
Digital Console Card A compatible Pro16 digital console card from any of Aviom’s technology partners may be substituted for the Y1 Yamaha card shown in the diagram. A-Net Out from the console card is connected to A-Net In on the D800. As with the analog version of the basic system, if a D800-Dante A-Net Distributor is used, the Dante Disable DIP switch (#10 in Switch Block 1) must be in the up position to use the A-Net In port.
32-Channels - Analog & Digital Inputs This hybrid system uses one digital console card plus one analog AN-16/i v.2 Input Module to provide up to 32 inputs to the network. The console card provides network slots 1-16 of the network; the AN-16/i v.2 Input Module provides slots 17-32. To configure this system: •• Connect A-Net Out on the console card to A-Net In on the AN-16/i v.2 with a Cat-5 cable. •• Set the Slot Range switch on the AN-16/i v.2 to 17-32.
32-64 Channels - Analog Inputs Up to four analog input devices may be connected to a D800 by cascading the A-Net ports on the A-Net input devices. The first input device in the system (Input Module 1 in the diagrams) can be an original AN-16/i Input Module or AN-16/i-M Mic Input Module. By default these devices supply network slots 1-16. To configure this system: •• Set the Slot Range switch on AN-16/i v.2 Input Module #1 to 1-16. •• Connect A-Net Out on #1 to A-Net In on AN-16/i v.
32-64 Channels - Console Card Inputs Up to four digital console cards from the same clock domain may be connected to a D800 by connecting the cards to an SB4 System Bridge. The A-Net streams connected to the System Bridge will be merged into a single Pro16e data stream by the D800 A-Net Distributor. If the digital console cards are installed in different consoles, the consoles must be clocked together using Word Clock.
32-64 Channels - Console Cards & Analog Up to three digital console cards from the same clock domain plus one AN-16/i v.2 Input Module may be combined to create a hybrid system that uses both analog and digital inputs to the network. An SB4 System Bridge is used to combine the A-Net outputs so that they may be connected to the D800’s A-Net input. Since there can only be one clock source, one of the console cards will be connected to the AN-16/i v.
SB4 Front Panel Setup Connect the SB4 System Bridge to the D800. If the D800-Dante A-Net Distributor is used, the Dante Disable DIP switch must be in the up position to use the A-Net input rather than the Dante network input.
Expanding a Personal Mixing System Any number of Pro16 A-Net devices can be used in a personal mixing system, including multiple D800 A-Net Distributors. To expand a system, additional D800 Distributors can be connected to any available A-Net Out port on a Pro16 device including A-16II and A-16R Personal Mixers, AN-16/O v.4 Output Modules, and the Pro64 ASI Systems Interface. Using Multiple D800 A-Net Distributors Multiple D800 units can be cascaded.
Using the A-16D Pro With the D800 A D800 (or D800-Dante) may be used along with an A-16D Pro A-Net Distributor in the same system. Connecting an A-16D Pro after a D800 allows up to 64 network slots to be transmitted to every port on each A-Net Distributor; use this as the default patching method if you are using A320 and A360 Personal Mixers. Up to 64 inputs may be made active in the network by using analog input devices, console cards connected to an SB4 System Bridge, or a Dante network.
Firmware Updates The D800 and D800-Dante A-Net Distributor’s firmware can be updated by the user to take advantage of new features and product updates. During a firmware update, the front panel A-Net ports are temporarily disabled; connected personal mixers will not be able to output audio. The rear panel A-Net In, A-Net Out, and Mixes Out ports are also disabled while firmware is being updated as is the Dante I/O on the D800-Dante version.
About USB Flash Drives A USB flash drive formatted for FAT32 (standard PC formatting) is required for firmware updates. It’s important to note that not all USB devices are created equal. In fact, even the same make and model USB device can have variations in their manufacture that are impossible to see by simply looking at the device or reading its specs. Some USB devices require that a driver be downloaded and installed before the data on the device can be used.
D800 A-Net Distributor Specifications Eight locking RJ45 connectors, powered A-Net to/from Personal Mixers (front panel) 2-position switch (I/II) accommodates A320, A-16II (I) and the bidirectional A360 Personal Mixer (II) A-Net In or A-Net Bridge In Accepts Pro16 or Pro16e A-Net; One locking RJ45 connector A-Net Out (rear panel) Pro16e A-Net; One locking RJ45 connector, unpowered A-Net Mixes Out Pro16e A-Net; One locking RJ45 connector, unpowered; Provides up to 16 channels of Network Mix Back™ data
D800-Dante Specifications Dante Primary I/O Locking RJ45 connector Dante Secondary I/O Locking RJ45 connector Stereo Link Four DIP Switch blocks: 1-16, 17-32, 33-48, and 49-64; used to set up to 32 channel pairs as stereo links Stereo Link Defeat Bypasses DIP switch stereo link settings Disable DIP switch Chooses Dante (down) or A-Net In (up) as the input source for the D800-Dante; When Dante is enabled, audio from the Network Mix Back feature is available to the Dante network.
Dimensions D800 and D800-Dante A-Net Distributors User Guide 43
D800 and D800-Dante A-Net Distributors User Guide 44
Cat-5 Cable Pinout The tables below detail the two wiring pinout variations for Cat-5 cables. When making custom cables, either pinout can be used, but both ends of a cable must use the same wiring pattern.
Index Symbols 1GB LED 22 2-position switch (I/II) 41 A A-16CS Control Surface 2 A-16D A-Net Distributor 2, 38 A-16D Pro A-Net Distributor 2, 3, 4, 19, 38 A-16II Personal Mixer 2, 4, 8, 11, 12, 32, 37, 38 A-16R Personal Mixer 2, 4, 8, 11, 37, 38 A320 Personal Mixer 8, 11, 12, 13, 30, 32, 38 A360 Channel Manager 3, 11, 12, 32 A360 Display 16 A360 Personal Mixer 3, 8, 11, 13, 16, 20, 30, 32, 37, 38 AC Line Conditioning 7 Active 42 Activity LED ACT 22 ACT LED 22 AN-16/i Input Module 4, 33 AN-16/i-M Mic Input M
console card 4, 8, 17, 31, 32, 34, 35, 38 crossover cables 5 D D800 A-Net Distributor 2, 3, 4 D800-Dante A-Net Distributor 4 daisy chain 11 Dante 8, 18, 21 bypass Stereo Link 42 Configuration 23 Network Mix Back 20 Dante configuration 21 Dante Controlle 26 Dante Controller 19, 20 Dante Controller software 22, 23 Dante Disable DIP switch 30, 31, 32, 37 Dante Firmware 40 Dante Firmware Update Manager 40 Dante input 23 Dante LEDs 21, 42 Dante network Error LED 21 Dante Primary 19, 23, 42 Dante Secondary 19, 2
Mode Switch 13 Mono 23 N network Wi-Fi 8 Network Activity LED 42 network activity LEDs 21 Network Config Tab 29 network input source 18 Network Mix Back 8, 9, 13, 19, 20, 38, 41, 42 Network Mix Back to Dante 20 network slot 11, 30 NTFS format 39 O Operating Temperature iii output module 37 override Stereo Links 23 P Package Contents 3 partition 39 PC format 39 permanent installation 5 Personal Mixer 8, 12, 38, 41 Personal Mixing System 30 Pinout 5, 45 Power LED 10 Power On 41 Power Supply 12, 19, 41 Prim
USB memory stick 39 USB port 10 V Voltage 41 W Warranty Registration 3 Wi-Fi 8 Wi-Fi router 16 wireless in-ear transmitter 20 wiring pinout 5 Word Clock 17, 18, 34, 35 Y Y1 A-Net Card for Yamaha 4, 31 D800 and D800-Dante A-Net Distributors User Guide 49
Warranty Registration Please take a moment to fill in this warranty registration form. Return it to Aviom via mail or fax. All information will be kept confidential.
1157 Phoenixville Pike, Suite 201 • West Chester, PA 19380 USA Voice: +1 610.738.9005 • Fax: +1 610.738.9950 • www.Aviom.
