Installation Guide Avigilon High Definition H.264 PTZ IP Dome Camera Models: 1.0W-H3PTZ-DP20 and 2.
This manual provides installation and operation information and precautions for the use of this dome camera. Incorrect installation could cause an unexpected fault. Before installing this equipment read this manual carefully. Please provide this manual to the owner of the equipment for future use.
Caution — Failure to observe the following instructions English may result in injury or damage to the dome camera. • • • • • • ii Do not install near any heat sources such as radiators, heat registers, stoves, or other sources of heat. Do not subject the cables to excessive stress, heavy loads or pinching. Do not open or disassemble the device. There are no user serviceable parts. Refer all servicing to qualified personnel.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003.
English Other Notices Compilation and Publication Notice This manual has been compiled and published covering the latest product descriptions and specifications. The contents of this manual and the specifications of this product are subject to change without notice.
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pendant Mount Adapter . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Camera Package Contents . . . . . . . . . . . . . . . . . . . 4 Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . .
English
English Overview Front View Serial Number Label Link LED Connection Status LED Feature Description Serial Number Label Product serial number and part number label. Link LED Indicates if there is an active connection in the Ethernet port. Connection Status LED Provides information about device operation. See LED indicators for more information.
Top View English Lanyard Anchor Ethernet Port External I/O External Power Feature Description External Power Accepts an external power connection when Power over Ethernet is not available. Lanyard Anchor The safety lanyard attaches to the anchor to prevent the camera from falling during installation. Ethernet Port Accepts an Ethernet connection to a network. Server communication and image data transmission occurs over this connection.
English Pendant Mount Adapter 1 1/2” NPT Mount Adapter Tamper Proof Screws Feature Description 1-1/2” NPT Mount Adapter Standard 1-1/2” NPT adapter for mounting the dome camera to a pendant mount bracket. Tamper Proof Screws TORX tamper-resistant captive screws to fix the dome camera to the NPT adapter.
English Installation Camera Package Contents Ensure the package contains the following: • • • • • • • Avigilon High Definition PTZ Dome Camera 1 ½” NPT Adapter T20 TORX tamper resistant key Teflon Sealing Tape RJ-45 crimp-on plug and weather-resistant housing External Power wiring harness, Avigilon Part #110-0017B External I/O wiring harness, Avigilon Part #110-0018B Installation Steps Complete the following procedures to install the dome camera. 1. 2. 3. 4. 5.
When applying the Teflon sealing tape, be sure to wrap in the same direction that the mount will be tightened. This will ensure the tape does not unravel when installing the mating parts together. Tip: Always apply Teflon tape to threaded mounts to help prevent the threads from binding 2. Pull the required cables through the mounting bracket then install the supplied connectors and wire assemblies. See Cable Connections for wiring details. 5 English camera connection.
Install the 1 1/2” NPT mount adapter. 4. Connect the safety lanyard from inside the NPT mount adapter to the anchor on the PTZ dome camera. English 3.
Refer to the camera’s Top View on page 2 for the location of the different connectors. Make sure the safety lanyard is connected to the PTZ dome camera before you complete the following cable connections: 1. 2. If there are external input or output devices that need to be connected to the camera (for example: door contacts, relays, analog video, speakers, etc), connect the devices to the camera I/O connector cable. For more information, see Connecting to External Devices.
Securing the PTZ Dome Camera English After the cable connections have been made, secure the PTZ dome camera to the mount. 1. Push the PTZ dome camera into the 1 1/2” NPT mount adapter then twist until it locks into place. NOTE: Be careful not to trap any cables between the dome camera housing and the mount adapter. 2. Use the tamper resistant key included with the dome camera to tighten the three tamper proof screws in the mount adapter.
• (Recommended) Avigilon Camera Installation Tool software application. • Camera's web browser interface: http:/// • ARP/Ping method. For more information, see Setting the IP Address through the ARP/Ping Method. • Network Video Management software application (for example, Avigilon Control Center). NOTE: The default camera username is admin and the default password is admin.
English Cable Connections Connecting External Power NOTE: This procedure is not required if Power over Ethernet (PoE) is used. If PoE is not available, the dome camera can be powered with 24 VAC or 24 VDC through the removable power connector: 1. Remove as much insulation as required to splice the supplied power connector to the power adapter wires (not included). Do not nick or damage the wires. 2. Remove the dummy plug from the power receptacle on the device.
External devices, including audio and video devices, are connected to the camera through the I/O cable. The pinout for the I/O connector is shown in the following table.
English The camera can be connected to an external microphone, speaker and video monitor through the I/O connector. NOTE: The camera only supports line level mono audio input and an NTSC or PAL video output. The video output signal is determined by the camera flicker control setting. When the camera flicker control is set to 60 Hz, the video output signal is NTSC. When the flicker control is set to 50 Hz, the video output signal is PAL.
Once the camera is connected to the network, the Connection Status LED will display the camera’s progress in connecting to the Network Video Management software. The following table describes what the LEDs indicate: Table: LED Indicators Connection State Connection Status LED Obtaining IP One short Address flash every second Discoverable Two short flashes every second Upgrading Two short Firmware flashes and one long flash every second Connected On Description Attempting to obtain an IP address.
English Reset to Factory Default Settings If the camera no longer functions as expected, you can choose to restore the camera to its factory default settings. Use the firmware revert button to reset the camera. NOTE: Be careful not to scratch the dome bubble. Firmware Revert Button Figure: The firmware revert microswitch between the status LEDs. 1. 2. 3. 4. Ensure the camera is powered on. Remove the dome cover by loosening the 4 tamper-proof screws that fix the cover to the base.
Complete the following steps to configure the camera to use a specific IP address: 1. 2. 3. 4. Locate and copy down the MAC Address (MAC) listed on the Serial Number Tag for reference. Open a Command Prompt window and enter the following commands: a. arp -s For example: arp -s 192.168.1.10 00-1885-12-45-78 b. ping -l 123 -t For example: ping -l 123 -t 192.168.1.10 Reboot the camera.
English Specifications Camera Lens 4.7-94mm, 20x zoom, F1.6 and automatic focus Network Network Cabling Type Connector API Security Protocols Streaming Protocols 100Base-TX CAT5 RJ-45 ONVIF compliant (www.onvif.
Avigilon warrants to the original consumer purchaser, that this product will be free of defects in material and workmanship for a period of 3 years from date of purchase. The manufacturer’s liability hereunder is limited to replacement of the product, repair of the product or replacement of the product with repaired product at the discretion of the manufacturer.
