SC264 Guide System 5
Legal Notices This guide is copyrighted ©2011 by Avid Technology, Inc., (hereafter “Avid”), with all rights reserved. Under copyright laws, this guide may not be duplicated in whole or in part without the written consent of Avid.
Contents Chapter 1. Introduction to the SC264 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 System Requirements and Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 About This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv SC264 Guide
Chapter 1: Introduction to the SC264 The SC264 is the System Control Computer for the postproduction versions of the System 5 and MaxAir families. Features of the SC264 include: • 4U rack-mountable chassis The following symbols are used to highlight important information: User Tips are helpful hints for getting the most from your system.
2 SC264 Guide
Chapter 2: SC264 Features Front Panel SC264 Front Panel Front Panel Elements Status Module Power Switch and Status Indicators See Status Module below. Software Status Indicator The blue wave icon in the Euphonix logo lights up to indicate the software in the SC264 is operating correctly. Detail of Status Module on Front Panel System Reset Switch Forces a manual reset of the SC264. Alarm Cancel Switch Cancels the audible hardware fault alarm.
Back Panel SC264 Back Panel 1. VGA Connector (DA-15) 11 SNMP LAN Port (RJ45) Main video monitor connection. Connect this port to a network with SNMP monitoring or e-mail services to enable the hardware monitoring system to report errors. 2. Keyboard (PS/2) Main keyboard connection. 3. Mouse (PS/2) Main trackball connection. 4. Serial Port 1 (DE-9) • Com1: not used. • Com2: wired internally to the SNMP board's Com port. 12. USB Ports Connect the USB MIDI Interface to one of these ports.
Connecting the SC264 Connect the machine room KVM extender (transmitter end) to the VGA, keyboard, and mouse connectors on the back panel of the SC264. A second KVM extender (receiver end) should be installed at the control surface, close to where the Emix monitor, keyboard and mouse are to be located. MaxAir systems have the receiver end inside the CM404. The KVM extenders are connected by a single CAT5 cable built into the console Ethernet harness (provided).
6 SC264 Guide
Appendix A: Compliance Information Environmental Compliance Disposal of Waste Equipment by Users in the European Union Proposition 65 Warning This product contains chemicals, including lead, known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. Perchlorate Notice This product may contain a lithium coin battery.
EMC (Electromagnetic Compliance) Avid declares that this product complies with the following standards regulating emissions and immunity: • FCC Part 15 Class A • EN55103-1 E4 • EN55103-2 E4 • AS/NZS CISPR 22 Class A • CISPR 22 Class A FCC Compliance for United States Communication Statement Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Safety Compliance Safety Statement This equipment has been tested to comply with USA and Canadian safety certification in accordance with the specifications of UL Standards: UL 60950-1:2007, 2nd Ed and CAN/CSA-22.2 No. 60950-1-07, 2nd Ed. Avid Inc., has been authorized to apply the appropriate NRTL mark on its compliant equipment. Warning 13) Unplug this equipment during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel.
10 SC264 Guide
Avid Technical Support (USA) Product Information 2001 Junipero Serra Boulevard Daly City, CA 94014-3886 USA Visit the Online Support Center at www.avid.com/support For company and product information, visit us on the web at www.avid.
