Installation Manual
Table Of Contents
- 17001_0_Frt-Matr
- 17001_1_Gen-Info
- 1.1 INTRODUCTION
- 1.2 FUNCTIONAL DESCRIPTION
- 1.2.1 Software Release Summary
- 1.2.2 Transponder Functional Overview
- 1.2.3 GPS Functional Overview
- 1.2.4 Lightning Detection (optional)
- 1.2.5 ADS-B System Overview
- 1.2.6 Traffic Display Functional Overview
- 1.2.7 FISB System Overview
- 1.2.8 Traffic Awareness System (option) Overview
- 1.2.9 ADS-B Traffic Advisory System Overview (optional)
- 1.2.10 Traffic Alert and Collision Avoidance System (option) Overview
- 1.2.11 Terrain Awareness and Warning System Overview (optional)
- 1.2.12 TerrainVisionTM
- 1.2.13 Discrete Inputs and Outputs Functional Overview
- 1.3 EQUIPMENT DESCRIPTIONS
- 1.4 INTERFACES
- 1.4.1 ADS-B Out Fail
- 1.4.2 AHRS Input
- 1.4.3 Altitude Encoder Input
- 1.4.4 Audio Out
- 1.4.5 Standby Mode
- 1.4.6 Audio Mute In and Out
- 1.4.7 Audio Acknowledge
- 1.4.8 RF Suppression Input/output
- 1.4.9 Traffic Alert
- 1.4.10 TAWS Caution and Warning Alert
- 1.4.11 WiFi Interface
- 1.4.12 WOW Input
- 1.4.13 Maintenance Interface
- 1.4.14 GPS Antenna
- 1.4.15 L-Band (978/1030/1090 MHz) Antenna
- 1.4.16 Directional Antenna
- 1.4.17 Traffic Display
- 1.4.18 Weather Display
- 1.4.19 Lightning Detection (WX-500)
- 1.4.20 Control Panel
- 1.5 INSTALLATION CONSIDERATIONS
- 1.6 SPECIFICATIONS
- 1.7 TSO INFORMATION
- 1.8 MODIFICATIONS
- 1.9 SOFTWARE REVISIONS
- 1.10 EQUIPMENT REQUIRED NOT SUPPLIED
- 1.11 EQUIPMENT INTERFACES
- 1.12 OBTAINING SOFTWARE
- 1.13 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 1.14 INSTALLATION APPROVAL AND LIMITATIONS
- 17001_2_Instal
- 2.1 INTRODUCTION
- 2.2 UNPACKING AND INSPECTING
- 2.3 INSTALLATION PROCEDURES
- 2.3.1 Panel Mount Location
- 2.3.2 Remote Mount Location
- 2.3.3 Electrical Connections
- 2.3.4 Compatible Equipment Installation Information
- 2.3.5 Discrete Inputs and Output Connections
- 2.3.6 Installation Guidelines for the DCM
- 2.3.7 P1 Mating Connector Assembly
- 2.3.8 Panel mount NGT-9000 Installation
- 2.3.9 Remote Mounted Lynx NGT-9000 Installation
- 2.3.10 CP-2500 Installation Guidelines
- 2.3.11 Antenna Installation Guidelines
- 17001_3_Inst_Check
- 3.1 INTRODUCTION
- 3.2 BASIC OPERATION
- 3.3 MPC (MAT) OPERATION
- 3.4 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 3.5 MAINTENANCE MODE
- 3.6 VERIFY SOFTWARE VERSION
- 3.7 SELECT CONFIGURATION OPTIONS
- 3.8 CALIBRATION SETUP
- 3.9 INTERFACE CHECK
- 3.10 SETUP PIM-9000 WIFI MODULE
- 3.11 INSTALLATION CHECKOUT
- 3.11.1 Functional Checks
- 3.11.2 Ground Checks
- 3.11.3 Electromagnetic Interference (E.M.I.) Check
- 3.11.4 Panel mount NGT-9000 Display Check
- 3.11.5 Flight Test
- 3.11.6 Installation Checkout Complete
- 17001_4_Maint
- 17001_5_App-A_signal
- A.1 INTRODUCTION
- A.2 INPUT AND OUTPUT INTERFACES
- A.2.1 Input Power
- A.2.2 RF Suppression Bus
- A.2.3 Audio Output
- A.2.4 Gillham Input (Altitude Input)
- A.2.5 RS-232 Interface
- A.2.6 RS-422 Interface
- A.2.7 ARINC 429 Input
- A.2.8 ARINC 429 Output
- A.2.9 Discrete Input
- A.2.10 Discrete Output
- A.2.11 I2C Serial Bus (Detachable Configuration Module)
- A.2.12 Antenna Connections
- A.3 PIN DEFINITION SUMMARY
- A.4 [J1 CONNECTOR]
- 17001_6_App-B_Environmental
- 17001_7_App-C_Compatibility
- 17001_8_App-D_TSO
- 17001_9_App-E_Questionaire
Lynx NGT-9000
Installation Manual
0040-17001-01 (Revision W) General Information Page 1-49
1.12 OBTAINING SOFTWARE
Software is available on the ACSS Publications website. If you have access to the ACSS Technical
Publications website go to https://support.acsscustomerservices.com/ACSS/support.aspx
. refer to the
LYNX 9000 SW folder for each software package.
If you do not have access go to and select the “Request Account Button” and fill out the form. After
completing the form press Submit.
If you cannot access the software or databases please contact ACSS via phone +1 (623) 445-7070 option
3 or via email at crc.acss@l3t.com
.
The MPC (MAT) is installed on the Maintenance PC and is used to transfer application software and
database data to the Lynx NGT-9000.
NOTES
1. Software tools are located in the equipment list (paragraph 1.10).
2. System software updates may only be accomplished by maintenance
personnel.
3. Starting with Release 2.1 updates to the 68DC and 72DC databases
must be purchased from Jeppesen. See Paragraph 1.12.1.
1.12.1 Obtaining Databases from Jeppesen
Databases for Airport (68DC), Map (72DC), and Terrain (71DC) are must be purchased from Jeppesen
®
.
Updates and subscriptions can be purchased for all the databases. The (71DC) Terrain database is
required for Release 3.0 and later. The 68DC, 72DC and 71DC databases are included in the product. See
Service Bulletin SB9029000-5 for more information.
NOTES
1. 71DC Terrain Database (World Terrain coverage) is updated on a 28-
day cycle to provide high resolution terrain co-located with airport
runway thresholds from the same cycle 68DC Navigation Database.
The Jeppesen Data Service has been setup to deliver cyclic updates of
both 68DC and 71DC databases.
2. For international customers it is necessary that the PC or laptop is set
for an American Windows installation (not only the language setting),
in order for the MPC (MAT) tool to operate correctly.
Jeppesen processes, compiles, reproduces, and provides the subscription service for the databases used in
the Lynx NGT-9000. Like all aviation databases, the information is ultimately supplied by government
agencies or other publicly available data. Because the information is provided by third party sources,
Jeppesen cannot guarantee the accuracy and completeness of the data. Jeppesen is continually working
towards improving the databases, so please report any irregularities or anomalies to Jeppesen at
www.jeppesen.com
.
Use the following procedure to obtain a database subscription from Jeppesen:
1. Contact Jeppesen via the web at http://www.jeppesen.com/company/feedback.jsp
and fill out the
form or contact Jeppesen directly at 1-800-353-2107 (direct - 1-303-799-9090).
2. A customer account will be established by Jeppesen and login credentials provided.