Installation Manual

Lynx NGT-9000
Installation Manual
0040-17001-01 (Revision W) Appendix D Page D-10
Table D-2: Applicable TSO and Deviations for NGT-9000RD
HW PART NO /
SW PART NO /
TYPE DESIGNATION DESCRIPTION APPLICABLE TSO AND DEVIATIONS CLASS, COMMENTS
9029000-40000 /
9020010-010 /
NGT-9000RD 3.2.2
Supports GPS, WiFi, and
ADS-B In via 1090ES and
ADS-B Out via 1090ES and
UAT.
Specific models support
TAS and Diversity and
TAS/Diversity.
Interfaces with traffic (RS-
422 and ARINC 429) and
weather (RS-422) displays.
Interfaces with control
panel (CP-2500 via RS-
232) or (other LRUs via
ARINC 429).
Supports ATAS and
Class
B
TAWS functionality.
Supports TCAS
Functionality.
TSO-C112d – Deviation Note 3, 5, 8 Level 2 dens Class 1
TSO-C118a – Deviation Note 2, 3, 10,
11, 12, 13
TSO-C145c – Deviation Note 1, 2, 4 Class Beta 1 (GPS
SBAS Output)
TSO-C147 – Deviation Note 1, 2, 4 Class A
TSO-C151c – Deviation Note 2, 9 Class B
TSO-C154c – Deviation Note 2, 4 Class A1S (receive
only)
TSO-C157a – Deviation Note 2, 4 Class 2 incomplete
TSO-C166b – Deviation Note 2, 3, 4, 8 Class A2
TSO-C195b – Deviation Note 2,4, 7 Class C1, C5, C7
Deviation Notes:
Deviation 1: TSO-C145c, TSO-C147. DO-160G was used instead of earlier versions.
Deviation 2: TSO-C118a, TSO-C145c, TSO-C151c, TSO-C147, TSO-C154c, TSO-C157a, TSO-C166b, TSO-
C195a, TSO-C195b Per the guidance in FAA Order 8150.1c, the units are marked with the primary TSO along with
a reference to the Installation Manual for the other TSO information (other applicable TSO’s, deviations, etc.).
Deviation 3: TSO-C112d, TSO-C166b. The Lynx NGT-9000 has an RF transmitter, which is used to generate both
the 1030MHz and 1090MHz waveforms for Mode S Transponder, ADS-B Out, and TAS functions. Due to the RF
power requirement and inherent non-linearity’s in RF transmitters, the harmonics of the transmitter exceed the RF
radiated emissions limit in DO-160G. ACSS deviates from DO—160G Section 21 Category M Radiated RF
Emissions in the following frequency bands when the transmitter is active:
TSO-C112d
• 2180 MHz ± 78 MHz (2nd Transmitter Harmonic) Exceeds Cat M by as much as 23 dB
• 3270 MHz ± 23 MHz (3rd Transmitter Harmonic) Exceeds Cat M by as much as 13 dB
• 4360 MHz ± 23 MHz (4th Transmitter Harmonic) Exceeds Cat M by as much as 14 dB
TSO-C166b
• 2180MHz ± 7MHz (2nd Transmitter harmonic) Exceeds Cat M by as much as 19.3dB
• 3270MHz ± 23MHz (3rd Transmitter harmonic) Exceeds Cat M by as much as 22.0dB
• 4360MHz ± 23MHz (4th Transmitter harmonic) Exceeds Cat M by as much as 24.4dB
• 5450MHz ± 23MHz (5th Transmitter harmonic) Exceeds Cat M by as much as 21.4d
Deviation 4: TSO-C145c, TSO-C147, TSO-C154c, TSO-157a, TSO-C166b, TSO-195a, TSO-195b. The Lynx NGT-
9000 utilizes a Maintenance Computer (i.e., a “special tool”) as its primary support tool required for installation and
debug effort. All installations will require that the Maintenance Computer be used to verify the software part number
that is stored electronically in the unit thereby ensuring the part has been installed in compliance to the type design
data. All software updates will also require that the Maintenance Computer be used to verify the software part
number that is stored electronically in the unit thereby ensuring the part is in compliance to the type design data.
Deviation 5: TSO- C112d. The NGT-9000 does not perform Comm-A (broadcast or addressed) or Comm-B Air-
Initiated ADLP (Airborne Data Link Processor) link operations. The NGT-9000 meets the certification of Level 2
transponders except for the support of the above listed ADLP functions.