Installation Manual
Table Of Contents
- 17001_0_Frt-Matr
- 17001_1_Gen-Info
- 1.1 INTRODUCTION
- 1.2 FUNCTIONAL DESCRIPTION
- 1.2.1 Software Release Summary
- 1.2.2 Transponder Functional Overview
- 1.2.3 GPS Functional Overview
- 1.2.4 Lightning Detection (optional)
- 1.2.5 ADS-B System Overview
- 1.2.6 Traffic Display Functional Overview
- 1.2.7 FISB System Overview
- 1.2.8 Traffic Awareness System (option) Overview
- 1.2.9 ADS-B Traffic Advisory System Overview (optional)
- 1.2.10 Traffic Alert and Collision Avoidance System (option) Overview
- 1.2.11 Terrain Awareness and Warning System Overview (optional)
- 1.2.12 TerrainVisionTM
- 1.2.13 Discrete Inputs and Outputs Functional Overview
- 1.3 EQUIPMENT DESCRIPTIONS
- 1.4 INTERFACES
- 1.4.1 ADS-B Out Fail
- 1.4.2 AHRS Input
- 1.4.3 Altitude Encoder Input
- 1.4.4 Audio Out
- 1.4.5 Standby Mode
- 1.4.6 Audio Mute In and Out
- 1.4.7 Audio Acknowledge
- 1.4.8 RF Suppression Input/output
- 1.4.9 Traffic Alert
- 1.4.10 TAWS Caution and Warning Alert
- 1.4.11 WiFi Interface
- 1.4.12 WOW Input
- 1.4.13 Maintenance Interface
- 1.4.14 GPS Antenna
- 1.4.15 L-Band (978/1030/1090 MHz) Antenna
- 1.4.16 Directional Antenna
- 1.4.17 Traffic Display
- 1.4.18 Weather Display
- 1.4.19 Lightning Detection (WX-500)
- 1.4.20 Control Panel
- 1.5 INSTALLATION CONSIDERATIONS
- 1.6 SPECIFICATIONS
- 1.7 TSO INFORMATION
- 1.8 MODIFICATIONS
- 1.9 SOFTWARE REVISIONS
- 1.10 EQUIPMENT REQUIRED NOT SUPPLIED
- 1.11 EQUIPMENT INTERFACES
- 1.12 OBTAINING SOFTWARE
- 1.13 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 1.14 INSTALLATION APPROVAL AND LIMITATIONS
- 17001_2_Instal
- 2.1 INTRODUCTION
- 2.2 UNPACKING AND INSPECTING
- 2.3 INSTALLATION PROCEDURES
- 2.3.1 Panel Mount Location
- 2.3.2 Remote Mount Location
- 2.3.3 Electrical Connections
- 2.3.4 Compatible Equipment Installation Information
- 2.3.5 Discrete Inputs and Output Connections
- 2.3.6 Installation Guidelines for the DCM
- 2.3.7 P1 Mating Connector Assembly
- 2.3.8 Panel mount NGT-9000 Installation
- 2.3.9 Remote Mounted Lynx NGT-9000 Installation
- 2.3.10 CP-2500 Installation Guidelines
- 2.3.11 Antenna Installation Guidelines
- 17001_3_Inst_Check
- 3.1 INTRODUCTION
- 3.2 BASIC OPERATION
- 3.3 MPC (MAT) OPERATION
- 3.4 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 3.5 MAINTENANCE MODE
- 3.6 VERIFY SOFTWARE VERSION
- 3.7 SELECT CONFIGURATION OPTIONS
- 3.8 CALIBRATION SETUP
- 3.9 INTERFACE CHECK
- 3.10 SETUP PIM-9000 WIFI MODULE
- 3.11 INSTALLATION CHECKOUT
- 3.11.1 Functional Checks
- 3.11.2 Ground Checks
- 3.11.3 Electromagnetic Interference (E.M.I.) Check
- 3.11.4 Panel mount NGT-9000 Display Check
- 3.11.5 Flight Test
- 3.11.6 Installation Checkout Complete
- 17001_4_Maint
- 17001_5_App-A_signal
- A.1 INTRODUCTION
- A.2 INPUT AND OUTPUT INTERFACES
- A.2.1 Input Power
- A.2.2 RF Suppression Bus
- A.2.3 Audio Output
- A.2.4 Gillham Input (Altitude Input)
- A.2.5 RS-232 Interface
- A.2.6 RS-422 Interface
- A.2.7 ARINC 429 Input
- A.2.8 ARINC 429 Output
- A.2.9 Discrete Input
- A.2.10 Discrete Output
- A.2.11 I2C Serial Bus (Detachable Configuration Module)
- A.2.12 Antenna Connections
- A.3 PIN DEFINITION SUMMARY
- A.4 [J1 CONNECTOR]
- 17001_6_App-B_Environmental
- 17001_7_App-C_Compatibility
- 17001_8_App-D_TSO
- 17001_9_App-E_Questionaire
Lynx NGT-9000
Installation Manual
0040-17001-01 (Revision W) Appendix A Page A-5
4. NGT-9000R, Release 3.2 or later. The following ARINC 429 labels are inputs from Control Panel #1
(Front or Left) on Bus #3 [Pins J1-44 & 45] for use by the embedded transponder only and not the
TAS/TCAS or TAWS function. Data speed is low:
• Label 013 – Display Control (DISC)
• Label 016 – Transponder Control (DISC)
• Label 233 – Flight ID 1 (DISC)
• Label 234 – Flight ID 2 (DISC)
• Label 235 – Flight ID 3 (DISC)
• Label 236 – Flight ID 4 (DISC)
NGT-9000R, Release 3.2 or later. The following ARINC 429 labels are inputs from Control Panel #2
(Aft or Right) on Bus #4 [Pins J1-46 & 47]. Data speed is low:
• Label 013 – Display Control (DISC)
• Label 016 – Transponder Control (DISC)
• Label 233 – Flight ID 1 (DISC)
• Label 234 – Flight ID 2 (DISC)
• Label 235 – Flight ID 3 (DISC)
• Label 236 – Flight ID 4 (DISC)
A.2.8 ARINC 429 Output
The unit has one ARINC 429 Output that transmits data at high (100 kbps). The Lynx NGT-9000 have
the option of interfacing to the Traffic display over the ARINC 429 bus using the standard traffic display
(STIF) format as defined in ARINC 735 and the Display Traffic Information File (DTIF) as described in
ARINC 735B. The specific display format is configurable through the DCM.
Release 3.2 or later the ARINC 429 Output can be configured to transmit information to a Control Panel.
The ARINC 429 Output can only be configured for one of these functions not both.
NOTE
The Lynx NGT-9000 follows the same STIF display as the L3 SKY-
497 TAS and SKY899 TCAS system. Select that option (if available)
in the STIF display configuration settings.
A.2.8.1 ARINC 429 Output Labels
1. The following ARINC 429 labels are output to a Traffic Display (CDTI) on Bus #1:
• Label 013 - TCAS Display Control (DSC)
• Label 015 - Altitude Select Limits (DSC)
• Label 016 - Mode S Control Panel Data (DSC)
• Label 103 - - Own Aircraft True Track Angle (BNR)
• Label 162 - Generic Discrete Word #1 (DSC) [Note 1]
• Label 163 - Application Availability (DSC)
• Label 270 - Vertical Resolution Advisories (DSC)
• Label 274 - Selected Sensitivity Level (DSC)
• Label 350 - TCAS Fault Summary (DSC)
• Label 371 - GA Equipment ID (DSC)
• Label 377 - Equipment ID (DSC)
• Label 110 - Own Aircraft Latitude - Coarse (BNR)
• Label 111 - Own Aircraft Longitude - Coarse (BNR)