Installation Manual
Table Of Contents
- 17001_0_Frt-Matr
- 17001_1_Gen-Info
- 1.1 INTRODUCTION
- 1.2 FUNCTIONAL DESCRIPTION
- 1.2.1 Software Release Summary
- 1.2.2 Transponder Functional Overview
- 1.2.3 GPS Functional Overview
- 1.2.4 Lightning Detection (optional)
- 1.2.5 ADS-B System Overview
- 1.2.6 Traffic Display Functional Overview
- 1.2.7 FISB System Overview
- 1.2.8 Traffic Awareness System (option) Overview
- 1.2.9 ADS-B Traffic Advisory System Overview (optional)
- 1.2.10 Traffic Alert and Collision Avoidance System (option) Overview
- 1.2.11 Terrain Awareness and Warning System Overview (optional)
- 1.2.12 TerrainVisionTM
- 1.2.13 Discrete Inputs and Outputs Functional Overview
- 1.3 EQUIPMENT DESCRIPTIONS
- 1.4 INTERFACES
- 1.4.1 ADS-B Out Fail
- 1.4.2 AHRS Input
- 1.4.3 Altitude Encoder Input
- 1.4.4 Audio Out
- 1.4.5 Standby Mode
- 1.4.6 Audio Mute In and Out
- 1.4.7 Audio Acknowledge
- 1.4.8 RF Suppression Input/output
- 1.4.9 Traffic Alert
- 1.4.10 TAWS Caution and Warning Alert
- 1.4.11 WiFi Interface
- 1.4.12 WOW Input
- 1.4.13 Maintenance Interface
- 1.4.14 GPS Antenna
- 1.4.15 L-Band (978/1030/1090 MHz) Antenna
- 1.4.16 Directional Antenna
- 1.4.17 Traffic Display
- 1.4.18 Weather Display
- 1.4.19 Lightning Detection (WX-500)
- 1.4.20 Control Panel
- 1.5 INSTALLATION CONSIDERATIONS
- 1.6 SPECIFICATIONS
- 1.7 TSO INFORMATION
- 1.8 MODIFICATIONS
- 1.9 SOFTWARE REVISIONS
- 1.10 EQUIPMENT REQUIRED NOT SUPPLIED
- 1.11 EQUIPMENT INTERFACES
- 1.12 OBTAINING SOFTWARE
- 1.13 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 1.14 INSTALLATION APPROVAL AND LIMITATIONS
- 17001_2_Instal
- 2.1 INTRODUCTION
- 2.2 UNPACKING AND INSPECTING
- 2.3 INSTALLATION PROCEDURES
- 2.3.1 Panel Mount Location
- 2.3.2 Remote Mount Location
- 2.3.3 Electrical Connections
- 2.3.4 Compatible Equipment Installation Information
- 2.3.5 Discrete Inputs and Output Connections
- 2.3.6 Installation Guidelines for the DCM
- 2.3.7 P1 Mating Connector Assembly
- 2.3.8 Panel mount NGT-9000 Installation
- 2.3.9 Remote Mounted Lynx NGT-9000 Installation
- 2.3.10 CP-2500 Installation Guidelines
- 2.3.11 Antenna Installation Guidelines
- 17001_3_Inst_Check
- 3.1 INTRODUCTION
- 3.2 BASIC OPERATION
- 3.3 MPC (MAT) OPERATION
- 3.4 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 3.5 MAINTENANCE MODE
- 3.6 VERIFY SOFTWARE VERSION
- 3.7 SELECT CONFIGURATION OPTIONS
- 3.8 CALIBRATION SETUP
- 3.9 INTERFACE CHECK
- 3.10 SETUP PIM-9000 WIFI MODULE
- 3.11 INSTALLATION CHECKOUT
- 3.11.1 Functional Checks
- 3.11.2 Ground Checks
- 3.11.3 Electromagnetic Interference (E.M.I.) Check
- 3.11.4 Panel mount NGT-9000 Display Check
- 3.11.5 Flight Test
- 3.11.6 Installation Checkout Complete
- 17001_4_Maint
- 17001_5_App-A_signal
- A.1 INTRODUCTION
- A.2 INPUT AND OUTPUT INTERFACES
- A.2.1 Input Power
- A.2.2 RF Suppression Bus
- A.2.3 Audio Output
- A.2.4 Gillham Input (Altitude Input)
- A.2.5 RS-232 Interface
- A.2.6 RS-422 Interface
- A.2.7 ARINC 429 Input
- A.2.8 ARINC 429 Output
- A.2.9 Discrete Input
- A.2.10 Discrete Output
- A.2.11 I2C Serial Bus (Detachable Configuration Module)
- A.2.12 Antenna Connections
- A.3 PIN DEFINITION SUMMARY
- A.4 [J1 CONNECTOR]
- 17001_6_App-B_Environmental
- 17001_7_App-C_Compatibility
- 17001_8_App-D_TSO
- 17001_9_App-E_Questionaire
Lynx NGT-9000
Installation Manual
0040-17001-01 (Revision W) Maintenance Page 4-43
Table 4-4: List of Fault Log Messages
FAULT ID/ CODE
(HEX)
FAULT DESCRIPTION CORRECTIVE ACTION
0x0000380B
Clear 1030 Rcvr Top TR Isolation
Failure
Log the fault.
0x0000380C
Clear 1030 XPDR ATCRBS Receiver
Failure
Log the fault.
0x0000380D
Clear XPDR 1090 XMIT Bottom
Power Failure
Log the fault.
0x0000380E
Clear XPDR 1090 XMIT Top Power
Failure
Log the fault.
0x00004001
GPS Sensor Fail
ADS-B In Internal failure
ADS-B Out Internal Degraded
GPS Internal failure
Check Table 4-1, Table 4-3, or Table 4-2
0x00004002 GPS Antenna Open/Short
ADS-B In External failure
ADS-B Out External Degraded
GPS External failure
Check if GPS antenna is properly
connected.
0x00004003
GPS/UAT LVDS Bus
ADS-B In Internal failure
ADS-B Out Internal Degraded
GPS Internal failure
FIS-B Internal failure
Check Table 4-1, Table 4-3, or Table 4-2
0x00004801
Clear GPS Sensor Fail
Log the fault.
0x00004802
Clear GPS Antenna Open/Short
Log the fault.
0x00004803
Clear GPS/UAT LVDS Bus
Log the fault.
0x00005001
UAT Sensor Failure
ADS-B In Internal degraded
FIS-B Internal failure
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x00005801
Clear UAT Sensor Failure
Log the fault.
0x00006003 Gillham C Bit Error
ADS-B In External failure
TAS External failure
TCAS External failure
Transponder External failure
Check wiring
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x00006004
RS232 Altitude Input Fail
ADS-B In External failure
TAS External failure
TCAS External failure
Transponder External failure
Check wiring
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x00006005
ARINC 429 Altitude Input Fail
ADS-B In External failure
TAS External failure
TCAS External failure
Transponder External failure
Check wiring
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x00006006
ARINC 429 AHRS Input Fail
ADS-B In External degraded
TAS External degraded
TCAS External degraded
Check wiring
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x00006007
ARINC 429 Receiver #1 Loop Back
Failure causes a reset
Log the fault.