Installation Manual
Table Of Contents
- 17001_0_Frt-Matr
- 17001_1_Gen-Info
- 1.1 INTRODUCTION
- 1.2 FUNCTIONAL DESCRIPTION
- 1.2.1 Software Release Summary
- 1.2.2 Transponder Functional Overview
- 1.2.3 GPS Functional Overview
- 1.2.4 Lightning Detection (optional)
- 1.2.5 ADS-B System Overview
- 1.2.6 Traffic Display Functional Overview
- 1.2.7 FISB System Overview
- 1.2.8 Traffic Awareness System (option) Overview
- 1.2.9 ADS-B Traffic Advisory System Overview (optional)
- 1.2.10 Traffic Alert and Collision Avoidance System (option) Overview
- 1.2.11 Terrain Awareness and Warning System Overview (optional)
- 1.2.12 TerrainVisionTM
- 1.2.13 Discrete Inputs and Outputs Functional Overview
- 1.3 EQUIPMENT DESCRIPTIONS
- 1.4 INTERFACES
- 1.4.1 ADS-B Out Fail
- 1.4.2 AHRS Input
- 1.4.3 Altitude Encoder Input
- 1.4.4 Audio Out
- 1.4.5 Standby Mode
- 1.4.6 Audio Mute In and Out
- 1.4.7 Audio Acknowledge
- 1.4.8 RF Suppression Input/output
- 1.4.9 Traffic Alert
- 1.4.10 TAWS Caution and Warning Alert
- 1.4.11 WiFi Interface
- 1.4.12 WOW Input
- 1.4.13 Maintenance Interface
- 1.4.14 GPS Antenna
- 1.4.15 L-Band (978/1030/1090 MHz) Antenna
- 1.4.16 Directional Antenna
- 1.4.17 Traffic Display
- 1.4.18 Weather Display
- 1.4.19 Lightning Detection (WX-500)
- 1.4.20 Control Panel
- 1.5 INSTALLATION CONSIDERATIONS
- 1.6 SPECIFICATIONS
- 1.7 TSO INFORMATION
- 1.8 MODIFICATIONS
- 1.9 SOFTWARE REVISIONS
- 1.10 EQUIPMENT REQUIRED NOT SUPPLIED
- 1.11 EQUIPMENT INTERFACES
- 1.12 OBTAINING SOFTWARE
- 1.13 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 1.14 INSTALLATION APPROVAL AND LIMITATIONS
- 17001_2_Instal
- 2.1 INTRODUCTION
- 2.2 UNPACKING AND INSPECTING
- 2.3 INSTALLATION PROCEDURES
- 2.3.1 Panel Mount Location
- 2.3.2 Remote Mount Location
- 2.3.3 Electrical Connections
- 2.3.4 Compatible Equipment Installation Information
- 2.3.5 Discrete Inputs and Output Connections
- 2.3.6 Installation Guidelines for the DCM
- 2.3.7 P1 Mating Connector Assembly
- 2.3.8 Panel mount NGT-9000 Installation
- 2.3.9 Remote Mounted Lynx NGT-9000 Installation
- 2.3.10 CP-2500 Installation Guidelines
- 2.3.11 Antenna Installation Guidelines
- 17001_3_Inst_Check
- 3.1 INTRODUCTION
- 3.2 BASIC OPERATION
- 3.3 MPC (MAT) OPERATION
- 3.4 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 3.5 MAINTENANCE MODE
- 3.6 VERIFY SOFTWARE VERSION
- 3.7 SELECT CONFIGURATION OPTIONS
- 3.8 CALIBRATION SETUP
- 3.9 INTERFACE CHECK
- 3.10 SETUP PIM-9000 WIFI MODULE
- 3.11 INSTALLATION CHECKOUT
- 3.11.1 Functional Checks
- 3.11.2 Ground Checks
- 3.11.3 Electromagnetic Interference (E.M.I.) Check
- 3.11.4 Panel mount NGT-9000 Display Check
- 3.11.5 Flight Test
- 3.11.6 Installation Checkout Complete
- 17001_4_Maint
- 17001_5_App-A_signal
- A.1 INTRODUCTION
- A.2 INPUT AND OUTPUT INTERFACES
- A.2.1 Input Power
- A.2.2 RF Suppression Bus
- A.2.3 Audio Output
- A.2.4 Gillham Input (Altitude Input)
- A.2.5 RS-232 Interface
- A.2.6 RS-422 Interface
- A.2.7 ARINC 429 Input
- A.2.8 ARINC 429 Output
- A.2.9 Discrete Input
- A.2.10 Discrete Output
- A.2.11 I2C Serial Bus (Detachable Configuration Module)
- A.2.12 Antenna Connections
- A.3 PIN DEFINITION SUMMARY
- A.4 [J1 CONNECTOR]
- 17001_6_App-B_Environmental
- 17001_7_App-C_Compatibility
- 17001_8_App-D_TSO
- 17001_9_App-E_Questionaire
Lynx NGT-9000
Installation Manual
0040-17001-01 (Revision W) Maintenance Page 4-42
Table 4-4: List of Fault Log Messages
FAULT ID/ CODE
(HEX)
FAULT DESCRIPTION CORRECTIVE ACTION
0x00003007
1030 Rcvr Top Power Failure
Transponder Internal failure
TAS Internal failure
TCAS Internal failure
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x00003008
1030 Rcvr Btm PIN Isolation Failure
Transponder Internal failure
TAS Internal failure
TCAS Internal failure
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x00003009
1030 Rcvr Top PIN Isolation Failure
Transponder Internal failure
TAS Internal failure
TCAS Internal failure
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x0000300A 1030 Rcvr Btm TR Isolation Failure
Transponder Internal failure
TAS Internal failure
TCAS Internal failure
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x0000300B
1030 Rcvr Top TR Isolation Failure
Transponder Internal failure
TAS Internal failure
TCAS Internal failure
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x0000300C
1030 XPDR ATCRBS Receiver
Failure
Transponder Internal failure
TAS Internal failure
TCAS Internal failure
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x0000300D
XPDR 1090 XMIT Bottom Power
Failure
Transponder Internal failure
ADS-B Internal failure
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x0000300E
XPDR 1090 XMIT Top Power Failure
Transponder Internal failure
ADS-B Internal failure
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x00003801
Clear Invalid Mode S Address
Log the fault.
0x00003802
Clear FPGA 1090 Transmission
Failure
Log the fault.
0x00003803
Clear Squitter rate failure
Log the fault.
0x00003804
Clear Squitter scheduler process not
running at expected rate
Log the fault.
0x00003805
Clear 1090 ATCRBS rx
Failure(without directional antenna)
Log the fault.
0x00003806
Clear 1030 Rcvr Btm Power Failure
Log the fault.
0x00003807
Clear 1030 Rcvr Top Power Failure
Log the fault.
0x00003808
Clear 1030 Rcvr Btm PIN Isolation
Failure
Log the fault.
0x00003809
Clear 1030 Rcvr Top PIN Isolation
Failure
Log the fault.
0x0000380A Clear 1030 Rcvr Btm TR Isolation
Failure
Log the fault.