Installation Manual
Table Of Contents
- 17001_0_Frt-Matr
- 17001_1_Gen-Info
- 1.1 INTRODUCTION
- 1.2 FUNCTIONAL DESCRIPTION
- 1.2.1 Software Release Summary
- 1.2.2 Transponder Functional Overview
- 1.2.3 GPS Functional Overview
- 1.2.4 Lightning Detection (optional)
- 1.2.5 ADS-B System Overview
- 1.2.6 Traffic Display Functional Overview
- 1.2.7 FISB System Overview
- 1.2.8 Traffic Awareness System (option) Overview
- 1.2.9 ADS-B Traffic Advisory System Overview (optional)
- 1.2.10 Traffic Alert and Collision Avoidance System (option) Overview
- 1.2.11 Terrain Awareness and Warning System Overview (optional)
- 1.2.12 TerrainVisionTM
- 1.2.13 Discrete Inputs and Outputs Functional Overview
- 1.3 EQUIPMENT DESCRIPTIONS
- 1.4 INTERFACES
- 1.4.1 ADS-B Out Fail
- 1.4.2 AHRS Input
- 1.4.3 Altitude Encoder Input
- 1.4.4 Audio Out
- 1.4.5 Standby Mode
- 1.4.6 Audio Mute In and Out
- 1.4.7 Audio Acknowledge
- 1.4.8 RF Suppression Input/output
- 1.4.9 Traffic Alert
- 1.4.10 TAWS Caution and Warning Alert
- 1.4.11 WiFi Interface
- 1.4.12 WOW Input
- 1.4.13 Maintenance Interface
- 1.4.14 GPS Antenna
- 1.4.15 L-Band (978/1030/1090 MHz) Antenna
- 1.4.16 Directional Antenna
- 1.4.17 Traffic Display
- 1.4.18 Weather Display
- 1.4.19 Lightning Detection (WX-500)
- 1.4.20 Control Panel
- 1.5 INSTALLATION CONSIDERATIONS
- 1.6 SPECIFICATIONS
- 1.7 TSO INFORMATION
- 1.8 MODIFICATIONS
- 1.9 SOFTWARE REVISIONS
- 1.10 EQUIPMENT REQUIRED NOT SUPPLIED
- 1.11 EQUIPMENT INTERFACES
- 1.12 OBTAINING SOFTWARE
- 1.13 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 1.14 INSTALLATION APPROVAL AND LIMITATIONS
- 17001_2_Instal
- 2.1 INTRODUCTION
- 2.2 UNPACKING AND INSPECTING
- 2.3 INSTALLATION PROCEDURES
- 2.3.1 Panel Mount Location
- 2.3.2 Remote Mount Location
- 2.3.3 Electrical Connections
- 2.3.4 Compatible Equipment Installation Information
- 2.3.5 Discrete Inputs and Output Connections
- 2.3.6 Installation Guidelines for the DCM
- 2.3.7 P1 Mating Connector Assembly
- 2.3.8 Panel mount NGT-9000 Installation
- 2.3.9 Remote Mounted Lynx NGT-9000 Installation
- 2.3.10 CP-2500 Installation Guidelines
- 2.3.11 Antenna Installation Guidelines
- 17001_3_Inst_Check
- 3.1 INTRODUCTION
- 3.2 BASIC OPERATION
- 3.3 MPC (MAT) OPERATION
- 3.4 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 3.5 MAINTENANCE MODE
- 3.6 VERIFY SOFTWARE VERSION
- 3.7 SELECT CONFIGURATION OPTIONS
- 3.8 CALIBRATION SETUP
- 3.9 INTERFACE CHECK
- 3.10 SETUP PIM-9000 WIFI MODULE
- 3.11 INSTALLATION CHECKOUT
- 3.11.1 Functional Checks
- 3.11.2 Ground Checks
- 3.11.3 Electromagnetic Interference (E.M.I.) Check
- 3.11.4 Panel mount NGT-9000 Display Check
- 3.11.5 Flight Test
- 3.11.6 Installation Checkout Complete
- 17001_4_Maint
- 17001_5_App-A_signal
- A.1 INTRODUCTION
- A.2 INPUT AND OUTPUT INTERFACES
- A.2.1 Input Power
- A.2.2 RF Suppression Bus
- A.2.3 Audio Output
- A.2.4 Gillham Input (Altitude Input)
- A.2.5 RS-232 Interface
- A.2.6 RS-422 Interface
- A.2.7 ARINC 429 Input
- A.2.8 ARINC 429 Output
- A.2.9 Discrete Input
- A.2.10 Discrete Output
- A.2.11 I2C Serial Bus (Detachable Configuration Module)
- A.2.12 Antenna Connections
- A.3 PIN DEFINITION SUMMARY
- A.4 [J1 CONNECTOR]
- 17001_6_App-B_Environmental
- 17001_7_App-C_Compatibility
- 17001_8_App-D_TSO
- 17001_9_App-E_Questionaire
Lynx NGT-9000
Installation Manual
0040-17001-01 (Revision W) Maintenance Page 4-40
Table 4-4: List of Fault Log Messages
FAULT ID/ CODE
(HEX)
FAULT DESCRIPTION CORRECTIVE ACTION
0x00001801
Clear Oscillator Synthesizer Out of
Lock
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x00001802
Clear Mutual Supp Bus Failed to
Assert
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x00001803
Clear Mutual Supp Bus Stuck High
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.
0x00001804
Clear DCM CRC Failure
Log the fault.
0x00001806
Clear DCM Configuration Fail
Log the fault.
0x00001807
Clear Over Temp on Ground
Log the fault.
0x00001808
Clear Over Temp in Air
Log the fault.
0x00001809
Clear Failure of Power Monitor
Log the fault.
0x0000180A
Clear Power Out of Tolerance
Log the fault.
0x0000180B
Clear Airport DB Flash CRC Failure
Log the fault.
0x0000180C
Clear Airport DB Flash Compatibility
Failure
Log the fault.
0x0000180D
Clear Map DB Flash CRC Failure
Log the fault.
0x0000180E Clear Map DB Flash Compatibility
Failure
Log the fault.
0x00001811
Clear Operational SW RAM CRC
Failure
Log the fault.
0x00001812
Clear Airport DB RAM CRC Failure
Log the fault.
0x00001813
Clear Map DB RAM CRC Failure
Log the fault.
0x00001815
Clear Factory Data RAM CRC
Failure
Log the fault.
0x00001816
Clear Config Data RAM CRC Failure
Log the fault.
0x00001817 Clear Factory Data NVM CRC
Failure
Log the fault.
0x00001818
Clear Factory Data Compatibility
Failure
Log the fault.
0x00001819
Clear Config Data NVM CRC Failure
Log the fault.
0x0000181A
Clear Config Data NVM Compatibility
Failure
Log the fault.
0x0000181B
Clear Power Loss In Air
Log the fault.
0x0000181C
Clear Ambient Light Sensor Failure
Log the fault.
0x00002001 Audio Mute While On Ground
Audio external failure
Log the fault.
0x00002002 TAS Antenna Failure
TAS External failure
TCAS Antenna Failure
TCAS External failure
Check Table 4-1, Table 4-3, or Table 4-2
0x00002003
1090 ADSB Rcvr Btm Power Failure
ADS-B In Internal degraded
TAS Internal failure
TCAS Internal failure
Reboot the unit and check if the fault
persists. Contact ACSS Field Service
before removal.