Installation Manual
Table Of Contents
- 17001_0_Frt-Matr
- 17001_1_Gen-Info
- 1.1 INTRODUCTION
- 1.2 FUNCTIONAL DESCRIPTION
- 1.2.1 Software Release Summary
- 1.2.2 Transponder Functional Overview
- 1.2.3 GPS Functional Overview
- 1.2.4 Lightning Detection (optional)
- 1.2.5 ADS-B System Overview
- 1.2.6 Traffic Display Functional Overview
- 1.2.7 FISB System Overview
- 1.2.8 Traffic Awareness System (option) Overview
- 1.2.9 ADS-B Traffic Advisory System Overview (optional)
- 1.2.10 Traffic Alert and Collision Avoidance System (option) Overview
- 1.2.11 Terrain Awareness and Warning System Overview (optional)
- 1.2.12 TerrainVisionTM
- 1.2.13 Discrete Inputs and Outputs Functional Overview
- 1.3 EQUIPMENT DESCRIPTIONS
- 1.4 INTERFACES
- 1.4.1 ADS-B Out Fail
- 1.4.2 AHRS Input
- 1.4.3 Altitude Encoder Input
- 1.4.4 Audio Out
- 1.4.5 Standby Mode
- 1.4.6 Audio Mute In and Out
- 1.4.7 Audio Acknowledge
- 1.4.8 RF Suppression Input/output
- 1.4.9 Traffic Alert
- 1.4.10 TAWS Caution and Warning Alert
- 1.4.11 WiFi Interface
- 1.4.12 WOW Input
- 1.4.13 Maintenance Interface
- 1.4.14 GPS Antenna
- 1.4.15 L-Band (978/1030/1090 MHz) Antenna
- 1.4.16 Directional Antenna
- 1.4.17 Traffic Display
- 1.4.18 Weather Display
- 1.4.19 Lightning Detection (WX-500)
- 1.4.20 Control Panel
- 1.5 INSTALLATION CONSIDERATIONS
- 1.6 SPECIFICATIONS
- 1.7 TSO INFORMATION
- 1.8 MODIFICATIONS
- 1.9 SOFTWARE REVISIONS
- 1.10 EQUIPMENT REQUIRED NOT SUPPLIED
- 1.11 EQUIPMENT INTERFACES
- 1.12 OBTAINING SOFTWARE
- 1.13 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 1.14 INSTALLATION APPROVAL AND LIMITATIONS
- 17001_2_Instal
- 2.1 INTRODUCTION
- 2.2 UNPACKING AND INSPECTING
- 2.3 INSTALLATION PROCEDURES
- 2.3.1 Panel Mount Location
- 2.3.2 Remote Mount Location
- 2.3.3 Electrical Connections
- 2.3.4 Compatible Equipment Installation Information
- 2.3.5 Discrete Inputs and Output Connections
- 2.3.6 Installation Guidelines for the DCM
- 2.3.7 P1 Mating Connector Assembly
- 2.3.8 Panel mount NGT-9000 Installation
- 2.3.9 Remote Mounted Lynx NGT-9000 Installation
- 2.3.10 CP-2500 Installation Guidelines
- 2.3.11 Antenna Installation Guidelines
- 17001_3_Inst_Check
- 3.1 INTRODUCTION
- 3.2 BASIC OPERATION
- 3.3 MPC (MAT) OPERATION
- 3.4 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 3.5 MAINTENANCE MODE
- 3.6 VERIFY SOFTWARE VERSION
- 3.7 SELECT CONFIGURATION OPTIONS
- 3.8 CALIBRATION SETUP
- 3.9 INTERFACE CHECK
- 3.10 SETUP PIM-9000 WIFI MODULE
- 3.11 INSTALLATION CHECKOUT
- 3.11.1 Functional Checks
- 3.11.2 Ground Checks
- 3.11.3 Electromagnetic Interference (E.M.I.) Check
- 3.11.4 Panel mount NGT-9000 Display Check
- 3.11.5 Flight Test
- 3.11.6 Installation Checkout Complete
- 17001_4_Maint
- 17001_5_App-A_signal
- A.1 INTRODUCTION
- A.2 INPUT AND OUTPUT INTERFACES
- A.2.1 Input Power
- A.2.2 RF Suppression Bus
- A.2.3 Audio Output
- A.2.4 Gillham Input (Altitude Input)
- A.2.5 RS-232 Interface
- A.2.6 RS-422 Interface
- A.2.7 ARINC 429 Input
- A.2.8 ARINC 429 Output
- A.2.9 Discrete Input
- A.2.10 Discrete Output
- A.2.11 I2C Serial Bus (Detachable Configuration Module)
- A.2.12 Antenna Connections
- A.3 PIN DEFINITION SUMMARY
- A.4 [J1 CONNECTOR]
- 17001_6_App-B_Environmental
- 17001_7_App-C_Compatibility
- 17001_8_App-D_TSO
- 17001_9_App-E_Questionaire
Lynx NGT-9000
Installation Manual
0040-17001-01 (Revision W) Maintenance Page 4-21
Table 4-3: Troubleshooting The Remote Mount NGT-9000R
SYMPTOMS CAUSE / CORRECTIVE ACTIONS
• No communication between NGT-
9000R and MAT tool.
• CP-2500 does NOT display “No
LRU Response” (FW 15 and
later).
1. Check Device Manager and look for NGT-9000 on USB
port.
2. If Device Manager shows no USB connection of NGT-
9000R, troubleshoot USB cable. Check laptop for ability to
connect USB to other device (printer, etc.).
3. If Device Manager shows USB connection to a generic
device, right click on this connection and load Zadig driver
for this connection.
The CP-2500 menu Initiated Self
Test shows Fail.
A fail condition is detected on the Lynx NGT-9000R.
1. Cycle power to the NGT-9000R and the CP-2500.
2. Replacement of the unit may be required. Contact ACSS
Field Service before removal of the unit.
• CP-2500 displays "ADS-B
SYSTEM FAIL".
• ADS-B Out Fail lamp flashes for
2 minutes and then remains ON
or ADS-B Out Fail lamp
illuminates without flashing
• Traffic (STIF) displays indicate
"DATA-FAIL" and WI-FI
information is not available.
The unit is operating, but has failed.
If installation was previously operational:
1. Connect to MAT and view fault logs and status screens to
troubleshoot cause of the failure.
2. Replacement of the Unit may be required. Contact ACSS
Field Service before removal of the unit.
In new installation (Assuming wiring has been verified):
1. Verify DCM was configured properly, applied, and the
power to the Unit was cycled to apply those settings.
2. Connect to MAT and view fault logs and status screens to
troubleshoot cause of the failure.
3. Replacement of the Unit may be required. Contact ACSS
Field Service before removal of the unit.
• CP-2500 displays “NO ADS-B
COVERAGE”.
• Displays – Normal operation.
NOTE
The lamp does not illuminate and
the CP-2500 message is not shown
if TAS/TCAS is active, if so
equipped.
A ground station is not being detected by the Lynx NGT-9000R.
1. Aircraft may not be within range of a local ground station.
2. Replacement of the Unit may be required. Contact ACSS
Field Service before removal of the unit.
NOTE
When crossing boundaries between ground station
coverage areas, out of coverage indications are normal.