Installation Manual
Table Of Contents
- 17001_0_Frt-Matr
- 17001_1_Gen-Info
- 1.1 INTRODUCTION
- 1.2 FUNCTIONAL DESCRIPTION
- 1.2.1 Software Release Summary
- 1.2.2 Transponder Functional Overview
- 1.2.3 GPS Functional Overview
- 1.2.4 Lightning Detection (optional)
- 1.2.5 ADS-B System Overview
- 1.2.6 Traffic Display Functional Overview
- 1.2.7 FISB System Overview
- 1.2.8 Traffic Awareness System (option) Overview
- 1.2.9 ADS-B Traffic Advisory System Overview (optional)
- 1.2.10 Traffic Alert and Collision Avoidance System (option) Overview
- 1.2.11 Terrain Awareness and Warning System Overview (optional)
- 1.2.12 TerrainVisionTM
- 1.2.13 Discrete Inputs and Outputs Functional Overview
- 1.3 EQUIPMENT DESCRIPTIONS
- 1.4 INTERFACES
- 1.4.1 ADS-B Out Fail
- 1.4.2 AHRS Input
- 1.4.3 Altitude Encoder Input
- 1.4.4 Audio Out
- 1.4.5 Standby Mode
- 1.4.6 Audio Mute In and Out
- 1.4.7 Audio Acknowledge
- 1.4.8 RF Suppression Input/output
- 1.4.9 Traffic Alert
- 1.4.10 TAWS Caution and Warning Alert
- 1.4.11 WiFi Interface
- 1.4.12 WOW Input
- 1.4.13 Maintenance Interface
- 1.4.14 GPS Antenna
- 1.4.15 L-Band (978/1030/1090 MHz) Antenna
- 1.4.16 Directional Antenna
- 1.4.17 Traffic Display
- 1.4.18 Weather Display
- 1.4.19 Lightning Detection (WX-500)
- 1.4.20 Control Panel
- 1.5 INSTALLATION CONSIDERATIONS
- 1.6 SPECIFICATIONS
- 1.7 TSO INFORMATION
- 1.8 MODIFICATIONS
- 1.9 SOFTWARE REVISIONS
- 1.10 EQUIPMENT REQUIRED NOT SUPPLIED
- 1.11 EQUIPMENT INTERFACES
- 1.12 OBTAINING SOFTWARE
- 1.13 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 1.14 INSTALLATION APPROVAL AND LIMITATIONS
- 17001_2_Instal
- 2.1 INTRODUCTION
- 2.2 UNPACKING AND INSPECTING
- 2.3 INSTALLATION PROCEDURES
- 2.3.1 Panel Mount Location
- 2.3.2 Remote Mount Location
- 2.3.3 Electrical Connections
- 2.3.4 Compatible Equipment Installation Information
- 2.3.5 Discrete Inputs and Output Connections
- 2.3.6 Installation Guidelines for the DCM
- 2.3.7 P1 Mating Connector Assembly
- 2.3.8 Panel mount NGT-9000 Installation
- 2.3.9 Remote Mounted Lynx NGT-9000 Installation
- 2.3.10 CP-2500 Installation Guidelines
- 2.3.11 Antenna Installation Guidelines
- 17001_3_Inst_Check
- 3.1 INTRODUCTION
- 3.2 BASIC OPERATION
- 3.3 MPC (MAT) OPERATION
- 3.4 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 3.5 MAINTENANCE MODE
- 3.6 VERIFY SOFTWARE VERSION
- 3.7 SELECT CONFIGURATION OPTIONS
- 3.8 CALIBRATION SETUP
- 3.9 INTERFACE CHECK
- 3.10 SETUP PIM-9000 WIFI MODULE
- 3.11 INSTALLATION CHECKOUT
- 3.11.1 Functional Checks
- 3.11.2 Ground Checks
- 3.11.3 Electromagnetic Interference (E.M.I.) Check
- 3.11.4 Panel mount NGT-9000 Display Check
- 3.11.5 Flight Test
- 3.11.6 Installation Checkout Complete
- 17001_4_Maint
- 17001_5_App-A_signal
- A.1 INTRODUCTION
- A.2 INPUT AND OUTPUT INTERFACES
- A.2.1 Input Power
- A.2.2 RF Suppression Bus
- A.2.3 Audio Output
- A.2.4 Gillham Input (Altitude Input)
- A.2.5 RS-232 Interface
- A.2.6 RS-422 Interface
- A.2.7 ARINC 429 Input
- A.2.8 ARINC 429 Output
- A.2.9 Discrete Input
- A.2.10 Discrete Output
- A.2.11 I2C Serial Bus (Detachable Configuration Module)
- A.2.12 Antenna Connections
- A.3 PIN DEFINITION SUMMARY
- A.4 [J1 CONNECTOR]
- 17001_6_App-B_Environmental
- 17001_7_App-C_Compatibility
- 17001_8_App-D_TSO
- 17001_9_App-E_Questionaire
Lynx NGT-9000
Installation Manual
0040-17001-01 (Revision W) Maintenance Page 4-7
Table 4-1: Troubleshooting The Panel Mount NGT-9000
SYMPTOM
SCREEN
CAUSE/CORRECTIVE ACTIONS
• Other aircraft are not shown
on the traffic screen.
• Ownship data is displayed.
• Alternate display shows
normal operation.
• ADS-
B Out Fail lamp is OFF.
• No Coverage Indicator is
showing on the display.
Traffic The aircraft is not in an ADS-B (UAT / 1090ES) coverage
area, or the targets are not transmitting ADS-B data, or the
ground station is not transmitting TIS-B data.
1.
The symptoms are normal if the target or ground station
is not transmitting TIS-B data.
2. The target or ground station needs to be within line-of-
site range.
3. Contact ACSS Field Service before removal of unit.
• Other aircraft are not shown
on the traffic screen.
• Ownship data may or may
not be displayed on the
weather screen.
• MSG button on screen.
Traffic Possible hardware problem with the unit.
1. Cycle power to the unit.
2. Check System Status Messages.
3. Check the MPC (MAT) fault log.
4. Contact ACSS Field Service before removal of unit.
• Ownship is shown, but no
traffic is being displayed.
• ADS-
B Out Fail lamp is OFF.
Traffic Possible problem with the UAT/1090 antenna or RF cables.
1. Cycle power to the unit.
2. Check cable connections.
3. Check System Status Messages.
4. Check the MPC (MAT) fault log.
5. Contact ACSS Field Service before removal of unit.
The traffic symbols on the traffic
display are non-directional
(diamond shape).
Traffic Non-directional traffic symbols on the traffic display is due to
one of the following reasons:
1. The traffic information that is being received by the unit
does not have directional data. The unit continues to
transmit non-directional data to the traffic display.
Note - TAS/TCAS traffic is not displayed as directional.
A TAS/TCAS and ADS-B correlated target will use the
ADS-B/TIS-B directional information.
2. An alternate (secondary STIF) traffic display does not
support the DTIF data format necessary to show
directional data provided by ADS-B.
Traffic display is working
correctly, but some aircraft are
not showing up on the display.
Traffic Lack of data as described below:
1. The ADS-B In requires other aircraft to be equipped
with ADS-B Out.
2. The TIS-B and ADS-R services are supported when in
range of ground stations and are providing the service.
3. If receiving the TIS-B service, but the Mode C and
Mode S transponder equipped aircraft that do not
provide altitude information are not seen on the traffic
display.
4. If receiving the TIS-B service, but aircraft not equipped
with a transponder, or equipped with a Mode A
transponder are not part of the TISB data and will not
be seen on the traffic display. Refer to the NGT-9000
Pilot guide for more information regarding what traffic
can be displayed.