Installation Manual
Table Of Contents
- 17001_0_Frt-Matr
- 17001_1_Gen-Info
- 1.1 INTRODUCTION
- 1.2 FUNCTIONAL DESCRIPTION
- 1.2.1 Software Release Summary
- 1.2.2 Transponder Functional Overview
- 1.2.3 GPS Functional Overview
- 1.2.4 Lightning Detection (optional)
- 1.2.5 ADS-B System Overview
- 1.2.6 Traffic Display Functional Overview
- 1.2.7 FISB System Overview
- 1.2.8 Traffic Awareness System (option) Overview
- 1.2.9 ADS-B Traffic Advisory System Overview (optional)
- 1.2.10 Traffic Alert and Collision Avoidance System (option) Overview
- 1.2.11 Terrain Awareness and Warning System Overview (optional)
- 1.2.12 TerrainVisionTM
- 1.2.13 Discrete Inputs and Outputs Functional Overview
- 1.3 EQUIPMENT DESCRIPTIONS
- 1.4 INTERFACES
- 1.4.1 ADS-B Out Fail
- 1.4.2 AHRS Input
- 1.4.3 Altitude Encoder Input
- 1.4.4 Audio Out
- 1.4.5 Standby Mode
- 1.4.6 Audio Mute In and Out
- 1.4.7 Audio Acknowledge
- 1.4.8 RF Suppression Input/output
- 1.4.9 Traffic Alert
- 1.4.10 TAWS Caution and Warning Alert
- 1.4.11 WiFi Interface
- 1.4.12 WOW Input
- 1.4.13 Maintenance Interface
- 1.4.14 GPS Antenna
- 1.4.15 L-Band (978/1030/1090 MHz) Antenna
- 1.4.16 Directional Antenna
- 1.4.17 Traffic Display
- 1.4.18 Weather Display
- 1.4.19 Lightning Detection (WX-500)
- 1.4.20 Control Panel
- 1.5 INSTALLATION CONSIDERATIONS
- 1.6 SPECIFICATIONS
- 1.7 TSO INFORMATION
- 1.8 MODIFICATIONS
- 1.9 SOFTWARE REVISIONS
- 1.10 EQUIPMENT REQUIRED NOT SUPPLIED
- 1.11 EQUIPMENT INTERFACES
- 1.12 OBTAINING SOFTWARE
- 1.13 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 1.14 INSTALLATION APPROVAL AND LIMITATIONS
- 17001_2_Instal
- 2.1 INTRODUCTION
- 2.2 UNPACKING AND INSPECTING
- 2.3 INSTALLATION PROCEDURES
- 2.3.1 Panel Mount Location
- 2.3.2 Remote Mount Location
- 2.3.3 Electrical Connections
- 2.3.4 Compatible Equipment Installation Information
- 2.3.5 Discrete Inputs and Output Connections
- 2.3.6 Installation Guidelines for the DCM
- 2.3.7 P1 Mating Connector Assembly
- 2.3.8 Panel mount NGT-9000 Installation
- 2.3.9 Remote Mounted Lynx NGT-9000 Installation
- 2.3.10 CP-2500 Installation Guidelines
- 2.3.11 Antenna Installation Guidelines
- 17001_3_Inst_Check
- 3.1 INTRODUCTION
- 3.2 BASIC OPERATION
- 3.3 MPC (MAT) OPERATION
- 3.4 INSTALLATION PROCEDURE FOR LYNXMSS USB DRIVER
- 3.5 MAINTENANCE MODE
- 3.6 VERIFY SOFTWARE VERSION
- 3.7 SELECT CONFIGURATION OPTIONS
- 3.8 CALIBRATION SETUP
- 3.9 INTERFACE CHECK
- 3.10 SETUP PIM-9000 WIFI MODULE
- 3.11 INSTALLATION CHECKOUT
- 3.11.1 Functional Checks
- 3.11.2 Ground Checks
- 3.11.3 Electromagnetic Interference (E.M.I.) Check
- 3.11.4 Panel mount NGT-9000 Display Check
- 3.11.5 Flight Test
- 3.11.6 Installation Checkout Complete
- 17001_4_Maint
- 17001_5_App-A_signal
- A.1 INTRODUCTION
- A.2 INPUT AND OUTPUT INTERFACES
- A.2.1 Input Power
- A.2.2 RF Suppression Bus
- A.2.3 Audio Output
- A.2.4 Gillham Input (Altitude Input)
- A.2.5 RS-232 Interface
- A.2.6 RS-422 Interface
- A.2.7 ARINC 429 Input
- A.2.8 ARINC 429 Output
- A.2.9 Discrete Input
- A.2.10 Discrete Output
- A.2.11 I2C Serial Bus (Detachable Configuration Module)
- A.2.12 Antenna Connections
- A.3 PIN DEFINITION SUMMARY
- A.4 [J1 CONNECTOR]
- 17001_6_App-B_Environmental
- 17001_7_App-C_Compatibility
- 17001_8_App-D_TSO
- 17001_9_App-E_Questionaire
Lynx NGT-9000
Installation Manual
0040-17001-01 (Revision W) Installation Checkout Page 3-7
NGT-9000R Release 2.0 & 2.1 (continued)
• TAWS FAIL: The TAWS function has failed.
• TAWS UNAVAILABLE: The TAWS function is unavailable due to not having a GPS position
solution of sufficient quality.
• TAS FAIL: The TAS function has failed.
• ADS-B IN FAIL: The ADS-B In and ATAS functions have failed.
• ADS-B IN UNAVAIL - POS: The ADS-B In and ATAS functions are unavailable due to not
having a GPS position solution of sufficient quality.
• XPDR FAIL: The transponder function has failed.
• ADS-B OUT FAIL: The ADS-B out is not being transmitted by the NGT-9000R due to the GPS
position not being available for more than 2 minutes or possibly a failure of the NGT-9000R.
• TAWS INH: The TAWS function is currently inhibited.
• OBST INH: The TAWS function is not alerting on obstacles.
• TAS DEGRADED: The TAS function is operating in a degraded condition.
• ADS-B OUT DEGRADED: The ADS-B out function is operating in a degraded condition.
• GPS FAIL (Priority In Air): The GPS derived position input is not functioning.
• GPS INIT (Priority In Air): GPS Initialization –The GPS contained within the NGT-9000R is
not ready. This message is removed after the GPS completes initialization.
• NO ADS-B COVERAGE: This message is removed once the NGT-900R begins receiving an
ADS-B ground station signal.
• FIS-B FAIL: The FIS-B function has failed.
• TAS OPR: TAS is operating while the aircraft is on ground.
• CONFIG MODULE - SERVICE SOON: Indicates a problem being detected with the
configuration module.
NGT-9000R Release 3.0, 3.1, 3.2, 3.2.1, & 3.2.2
• NO LRU RESPONSE: The CP-2500 has detected loss of communication with the NGT-9000R.
This is a CP-2500 message that was incorporated in Firmware 15 and later.
• GPS FAIL (Priority On Ground): The GPS derived position input is not functioning.
• GPS INIT (Priority On Ground): GPS Initialization –The GPS contained within the NGT-
9000R is not ready. This message is removed after the GPS completes initialization.
• PULL UP: This is a TAWS Warning Alert that is accompanied by an aural announcement.
• TERRAIN: This is a TAWS Caution Alert that is accompanied by an aural announcement.
• TRAFFIC: This is an TAS/TCAS or ATAS Traffic Advisory that is accompanied by an aural
announcement.
• GND MODE: Unit is in ground test mode.