User Manual

MDR2400 and MDR5800 User Manual
862-01881 Issue 8 Page 102
Object ID Group Object Type Acce
ss
Description
1.3.6.1.4.1.1316.1.1.1.3.5.1 mdrmteEventLogEntry SYNTAX
1.3.6.1.4.1.1316.1.1.1.3.5.1.1 mdrmteEventIndex INTEGER
1.3.6.1.4.1.1316.1.1.1.3.5.1.2 mdrmteEventDate DisplayString read-
only
Lists the date on which the event
occurred.
1.3.6.1.4.1.1316.1.1.1.3.5.1.3 mdrmteEventTime DisplayString read-
only
Lists the time when the event
occurred.
1.3.6.1.4.1.1316.1.1.1.3.5.1.4 mdrmteEventType INTEGER read-
only
Lists the type of event -
informational, minor, major or
critical.
1.3.6.1.4.1.1316.1.1.1.3.5.1.5 mdrmteEventDescription DisplayString read-
only
Textual description of the logged
event.
1.3.6.1.4.1.1316.1.1.1.3.6 mdrmteClearEventLog INTEGER write
-only
This entry is used to clear the
Event Log.
1.3.6.1.4.1.1316.1.1.1.3.7 mdrmteResetAllFaults INTEGER write
-only
1.3.6.1.4.1.1316.1.1.1.3.8
mdrmteEnableDebug INTEGER read-
write
This entry is used to enable test
and debugging features
1.3.6.1.4.1.1316.1.1.1.3.9
mdrmteErrorWindow INTEGER read-
write
This entry is used to set the time
period in minutes during which
errors are counted, but not
logged.
1.3.6.1.4.1.1316.1.1.1.4 mdrmteAccess
1.3.6.1.4.1.1316.1.1.1.4.1 mdrmteEthernetIPAddress IpAddress read-
write
The IP address associated with
product's Ethernet port (NOTE :
USE A POWER-ON RESET OR
RESET BUTTON POSITION ‘3’
TO ALLOW ACCEPTANCE OF
THE NEW IP ADDRESS – I.E. IT
IS UPDATED IN NON-VOLATILE
MEMORY AND GETS
ACCEPTED BY THE INDOOR
UNIT’S IP STACK AS A VALID
ADDRESS).
1.3.6.1.4.1.1316.1.1.1.4.2 mdrmteEthernetNetMask IpAddress read-
write
The netmask associated with the
Ethernet port.
1.3.6.1.4.1.1316.1.1.1.4.3 mdrmteMaxNumUsers INTEGER read-
only
If the firmware is complied with
the security feature switched on,
users can log into an IU. This
value is read back from the IU
and indicates the maximum
number of users that can
connect to an Indoor Unit.
1.3.6.1.4.1.1316.1.1.1.4.4 mdrmteMaxNumActiveUsers INTEGER read-
only
If the firmware is built with the
security feature switched on,
users can log into an IU. This
entry defines the maximum
number of active users that can
be connected to an Indoor Unit
using IP.
1.3.6.1.4.1.1316.1.1.1.4.5 mdrmteNumActiveUsers Gauge read-
only
If the firmware is built with the
security feature switched on,
users can log into an IU. This
entry defines the number of
active users logged into an IU.
1.3.6.1.4.1.1316.1.1.1.4.6 mdrmteUserTable SEQUENCE
1.3.6.1.4.1.1316.1.1.1.4.6.1 mdrmteUserEntry SYNTAX